Oligo Ethylene Glycol Side Chains Research Articles

The Role of Long-Alkyl-Group Spacers in Glycolated Copolymers for High-Performance Organic Electrochemical Transistors.

Semiconducting polymers with oligoethylene glycol (OEG) sidechains have attracted strong research interest for organic electrochemical transistor (OECT) applications. However, key molecular design rules for high-performance OECTs via efficient mixed electronic/ionic charge transport are still unclear. In this work, new glycolated copolymers (gDPP-TTT and gDPP-TTVTT) with diketopyrrolopyrrole (DPP) acceptor and thiophene (T) and vinylene (V) thiophene-based donor units are synthesized and characterized for accumulation mode OECTs, where a long-alkyl-group (C12 ) attached to the DPP unit acts as a spacer distancing the OEG groups from the polymer backbone. gDPP-TTVTT shows the highest OECT transconductance (61.9 S cm-1 ) and high operational stability, compared to gDPP-TTT and their alkylated counterparts. Surprisingly, gDPP-TTVTT also shows high electronic charge mobility in a field-effect transistor, suggesting efficient ion injection/diffusion without hindering its efficient electronic charge transport. The elongated donor unit (TTVTT) facilitates hole polaron formation to be more localized to the donor unit, leading to faster and easier polaron formation with less impact on polymer structure during OECT operation, as opposed to the TTT unit. This is supported by molecular dynamics simulation. These simultaneously high electronic and ionic charge-transport properties are achieved due to the long-alkyl-group spacer in amphipathic sidechains, providing an important molecular design rule for glycolated copolymers.

Electrochromic and photovoltaic properties of benzothiadiazole-based donor-acceptor conjugated polymers with oligo(ethylene glycol) side chains

Introduced oligo(ethylene glycol) (OEG) chains into high-performance donor-acceptor (D-A) type conjugated polymers is a promising strategy to control the π-π stacking, energy levels, solubility, and electrical properties. In this work, a series of novel PDTBF polymers (PDTBF-DTh, PDTBF-ThSe, and PDTBF-Th) were synthesized based on the typical benzothiadiazole-thiophene (BT-Th)-based polymer substituted with OEG side chains to investigate their electrochromic (EC) and photovoltaic performance. The resultant PDTBF polymers had fast switching speed (i.e., chlorobenzene-prepared PDTBF-Th EC film: Tc0.9 = 1.8 s, Tb0.9 = 1.0 s), and high coloration efficiencies (i.e., chlorobenzene-prepared PDTBF-ThSe EC film: 255.50 cm2 C−1). Moreover, the PDTBF-DTh:Y6-based device shows a power conversion efficiency (PCE) of 3.11%. Due to the induced amphiphilic OEG side chains on the backbone of the conjugated polymer, these materials also exhibited green solvent processing potential. It is worth noting that these PDTBF polymers exhibited much wider optical bandgaps (1.95 eV–2.16 eV) than other reported PDTBF polymers (mostly narrow band gaps: 1.40–1.70 eV), due to the format of linkage between OEG side chains and thiophene units. It is an effective strategy to control the optical properties of the conjugated polymers using OEG side chain engineering investigation.

Discovering Crystal Forms of the Novel Molecular Semiconductor OEG-BTBT

This work is focused on a polymorphic and crystallographic study of a novel p-type organic semiconductor 2,7-bis(2-(2-methoxyethoxy)ethoxy)benzo[b]benzo[4,5]thieno[2,3-d]thiophene (OEG-BTBT). The well-known BTBT core is functionalized by eight-atom-long oligoethylene glycol side chains. Our results demonstrate the discovery of three crystal forms of the OEG-BTBT molecule, namely, Form I, Form II, and Form III, in different experimental conditions. Crystal structures of Form I and Form III are reported, while only unit cell indexing of Form II could be determined. Form I and Form II are enantiotropically related, and Form II is stable at temperatures higher than 127 °C. The kinetics of transformation to Form II was studied by the Avrami equation. Form III is a solvate crystal form which is rarely observed in the field of organic electronics, and upon release of dichloromethane, it converts to Form I. Furthermore, we studied the mechanical properties of the Form I crystals, which exhibit plastic bending upon applying mechanical stress in the [100] direction. This distinct mechanical behavior is rationalized by the slip layer topology, the intermolecular interactions energies from energy frameworks, and the Hirshfeld surface analysis.

High‐Performance n‐Type Organic Electrochemical Transistors Enabled by Aqueous Solution Processing of Amphiphilicity‐Driven Polymer Assembly

AbstractDespite the growing attention on organic electrochemical transistors (OECTs), most research has focused on the design of p‐type active materials, and the number of high‐performance n‐type materials is limited. Herein, a series of naphthalene diimide‐based polymers incorporated with asymmetrically branched oligo(ethylene glycol) (OEG) side chains are developed to enable green‐solvent‐processed, high‐performance n‐type OECTs. The branched OEG side chains afford sufficient solubility in eco‐friendly ethanol/water solvent mixtures. Importantly, taking advantage of the amphiphilic nature of OEG‐based polymers, ethanol/water solvents selectively solvate hydrophilic OEG side chains, while producing assembled π−π stacks of hydrophobic backbones. This enables highly ordered polymer packing with a preferential edge‐on orientation, and thus excellent lateral charge transport. In particular, the fine‐tuned OEG side chains of P(NDIMTEG‐T) provide compact backbone packing, effective polaron generation, and superior electrochemical stability with optimized swelling capability. The resultant n‐type OECT shows the best electrical/electrochemical performance in the family, represented by a high transconductance (gm) of 0.38 S cm−1 and a large figure‐of‐merit (µC*) of 0.56 F V−1 cm−1 s−1. This study demonstrates the use of aqueous processing in OECTs, for the first time, and suggests important guidelines for the design of n‐type organic mixed ionic‐electronic conductors with excellent OECT characteristics.

Tuning of the elastic modulus of a soft polythiophene through molecular doping.

Molecular doping of a polythiophene with oligoethylene glycol side chains is found to strongly modulate not only the electrical but also the mechanical properties of the polymer. An oxidation level of up to 18% results in an electrical conductivity of more than 52 S cm-1 and at the same time significantly enhances the elastic modulus from 8 to more than 200 MPa and toughness from 0.5 to 5.1 MJ m-3. These changes arise because molecular doping strongly influences the glass transition temperature Tg and the degree of π-stacking of the polymer, as indicated by both X-ray diffraction and molecular dynamics simulations. Surprisingly, a comparison of doped materials containing mono- or dianions reveals that - for a comparable oxidation level - the presence of multivalent counterions has little effect on the stiffness. Evidently, molecular doping is a powerful tool that can be used for the design of mechanically robust conducting materials, which may find use within the field of flexible and stretchable electronics.

Fabrication of substrates for multiple cell patterning using a copolymer with a UV-degradable oligoethylene glycol side chain

Patterning of a surface modified with the copolymer of ω-methoxy-(ethylene glycol)8 acrylamide and 3-methacryloxypropyltrimethoxysilane by UV irradiation and the creation of a heterologous cell patterning surface.

Oligoethylene Glycol Side Chains Increase Charge Generation in Organic Semiconductor Nanoparticles for Enhanced Photocatalytic Hydrogen Evolution.

Organic semiconductor nanoparticles (NPs) composed of an electron donor/acceptor (D/A) semiconductor blend have recently emerged as an efficient class of hydrogen-evolution photocatalysts. It is demonstrated that using conjugated polymers functionalized with (oligo)ethylene glycol side chains in NP photocatalysts can greatly enhance their H2 -evolution efficiency compared to their nonglycolated analogues. The strategy is broadly applicable to a range of structurally diverse conjugated polymers. Transient spectroscopic studies show that glycolation facilitates charge generation even in the absence of a D/A heterojunction, and further suppresses both geminate and nongeminate charge recombination in D/A NPs. This results in a high yield of photogenerated charges with lifetimes long enough to efficiently drive ascorbic acid oxidation, which is correlated with greatly enhanced H2 -evolution rates in the glycolated NPs. Glycolation increases the relative permittivity of the semiconductors and facilitates water uptake. Together, these effects may increase the high-frequency relative permittivity inside the NPs sufficiently, to cause the observed suppression of exciton and charge recombination responsible for the high photocatalytic activities of the glycolated NPs.

Aldehyde-Functional Diblock Copolymer Nano-objects via RAFT Aqueous Dispersion Polymerization.

We report the rational design of aldehyde-functional sterically stabilized diblock copolymer nano-objects in aqueous solution via polymerization-induced self-assembly. More specifically, reversible addition-fragmentation chain transfer aqueous dispersion polymerization of 2-hydroxypropyl methacrylate is conducted using a water-soluble precursor block in which every methacrylic repeat unit contains a pendent oligo(ethylene glycol) side chain capped with a cis-diol unit. Systematic variation of the reaction conditions enables the construction of a pseudo-phase diagram, which ensures the reproducible targeting of pure spheres, worms, or vesicles. Selective oxidation of the pendent cis-diol groups using aqueous sodium periodate under mild conditions introduces geminal diols (i.e., the hydrated form of an aldehyde obtained in the presence of water) into the steric stabilizer chains without loss of colloidal stability. In the case of diblock copolymer vesicles, such derivatization leads to the formation of a worm population, indicating partial loss of the original morphology. However, this problem can be circumvented by cross-linking the membrane-forming block prior to periodate oxidation. Moreover, such covalently stabilized aldehyde-functionalized vesicles can be subsequently reacted with either glycine or histidine in aqueous solution, followed by reductive amination to prevent hydrolysis of the labile imine bond. ζ potential measurements confirm that this derivatization significantly affects the electrophoretic behavior of these vesicles. Similarly, the membrane-crosslinked aldehyde-functionalized vesicles can be reacted with a model globular protein, bovine serum albumin, to produce "stealthy" protein-decorated vesicles.

Electrically Conducting Elastomeric Fibers with High Stretchability and Stability

Stretchable conducting materials are appealing for the design of unobtrusive wearable electronic devices. Conjugated polymers with oligoethylene glycol side chains are excellent candidate materials owing to their low elastic modulus and good compatibility with polar stretchable polymers. Here, electrically conducting elastomeric blend fibers with high stretchability, wet spun from a blend of a doped polar polythiophene with tetraethylene glycol side chains and a polyurethane are reported. The wet-spinning process is versatile, reproducible, scalable, and produces continuous filaments with a diameter ranging from 30 to 70µm. The fibers are stretchable up to 480% even after chemical doping with iron(III) p-toluenesulfonate hexahydrate and exhibit an electrical conductivity of up to 7.4 S cm-1 , which represents a record combination of properties for conjugated polymer-based fibers. The fibers remain conductive during elongation until fiber fracture and display excellent long-term stability at ambient conditions. Cyclic stretching up to 50% strain for at least 400 strain cycles reveals that the doped fibers exhibit high cyclic stability and retain their electrical conductivity. Finally, a directional strain sensing device, which makes use of the linear increase in resistance of the fibers up to 120% strain is demonstrated.

Revealing the effect of oligo(ethylene glycol) side chains on n‐doping process in FBDPPV‐based polymers

AbstractThe low doping efficiency of n‐doped systems limits the development of n‐type organic conducting materials. Oligo(ethylene glycol) (OEG) as the flexible chain in conjugated small molecules and polymers may improve doping efficiency. However, OEG side chains also bring unexpected low mobility and poor film morphology. Herein, we propose the stronger solution‐state aggregation plays a dominated role in charge transport and morphology of OEG‐substituted polymer. The solution‐state aggregation also affects doping process. Therefore, we develop a series of polymers based on 3,7‐bis((E)‐7‐fluoro‐1‐(2‐octyldodecyl)‐2‐oxoindolin‐3‐ylidene)‐3,7‐dihydrobenzo[1,2‐b:4,5‐b']difuran‐2,6‐dione (FBDPPV) with different ratios of OEG side chain to investigate the effect of side chain on solution‐state aggregation and n‐doping process. After n‐doped by hexahydro‐1H,3a1H,4H,7H‐3a,6a,9a‐triazaphenalene (TAM), FBDPPV with 50% OEG affords the highest doping efficiency and conductivity, while FBDPPV with 100% OEG shows lower conductivity. Combination of ultraviolet–visible–near infrared absorption spectra, grazing‐incidence wide‐angle X‐ray scattering and atomic force microscopy, we reveal that serious aggregated extent in solution of OEG‐substituted polymer result in phase separation and rough morphology, which are the origins of poor conductivity. Our work provides a new perspective on the effect of the OEG side chain on the doped polymer systems, suggesting suitable solution‐state aggregation is crucial to high doping efficiency and high conductivity.

Asymmetric Glycolated Substitution for Enhanced Permittivity and Ecocompatibility of High-Performance Photovoltaic Electron Acceptor.

Traditional organic photovoltaic materials exhibit low dielectric constants (εr) of 3 to 4, restricting the further enhancement of power conversion efficiencies (PCEs) of organic solar cells (OSCs). Herein we design and synthesize a fused-ring electron acceptor named Y6-4O through introducing an asymmetric highly polarizable oligo(ethylene glycol) side chain onto the pyrrole unit of Y6. Compared with alkylated Y6 (εr = 3.36), asymmetric glycolated Y6-4O shows a notably higher εr value of 5.13 and better solubility in nonhalogen solvents. Because of the higher εr value, the devices based on as-cast PM6:Y6-4O processed using toluene exhibit a higher charge separation yield, slower bimolecular recombination kinetics, and less voltage loss relative to the control devices based on PM6:Y6. Consequently, a high PCE of 15.2% is achieved for PM6:Y6-4O-based devices, whereas the PM6:Y6-based devices show PCEs of only 7.38%. 15.2% is the highest PCE for the as-cast nonhalogenated processed OSC devices, and it is also much higher than the values (<8.5%) reported for OSCs based on high-permittivity (εr > 5) organic photovoltaic semiconductors.

Electron Transport Layers Based on Oligo(ethylene glycol)-Incorporated Polymers Enabling Reproducible Fabrication of High-Performance Organic Solar Cells

Interlayers in organic solar cells (OSCs) play a crucial role in determining their charge extraction properties, device performance, and stability. In this work, two naphthalene diimide (NDI)-based n-type polymers (P(NDIDEG-T) and P(NDITEG-T)) incorporating oligo(ethylene glycol) (OEG) side chains of different lengths are designed and used as new electron transport layers (ETLs) in OSCs. The hydrophilic OEG side chains enable the processing of these n-type polymers using eco-friendly water/ethanol mixtures. In addition, the polar OEG groups effectively modify the work function of the Ag cathode, enabling the polymers to function as efficient ETLs. Consequently, when these OEG-based ETLs are applied to PM6:Y6-based OSCs, a maximum power conversion efficiency (PCE) of 15.43% is achieved, which is substantially higher than that of a reference OSC without an ETL (9.93%) and comparable to that of an OSC with a representative high-performance PFN-Br ETL (15.34%). We demonstrate that the P(NDIDEG-T)-based OSCs show both enhanced PCEs and better reproducibility than their P(NDITEG-T)-based counterparts, which are attributed to the lower surface tension and improved film uniformity of the P(NDIDEG-T) ETL. Also, the P(NDIDEG-T) ETL realizes OSCs with higher storage stability and more thickness-tolerant performance compared to the P(NDITEG-T) and PFN-Br ETLs. Our study provides useful guidelines for the design of ETLs suitable for the fabrication of high-performance, reproducible, and stable OSCs.

Designing Nonfullerene Acceptors with Oligo(Ethylene Glycol) Side Chains: Unraveling the Origin of Increased Open-Circuit Voltage and Balanced Charge Carrier Mobilities.

Despite the recent rapid development of organic solar cells (OSCs), the low dielectric constant (ϵr =3-4) of organic semiconducting materials limits their performance lower than inorganic and perovskite solar cells. In this work, we introduce oligo(ethylene glycol) (OEG) side chains into the dicyanodistyrylbenzene-based non-fullerene acceptors (NIDCS) to increase its ϵr up to 5.4. In particular, a NIDCS acceptor bearing two triethylene glycol chains (NIDCS-EO3) shows VOC as high as 1.12 V in an OSC device with a polymer donor PTB7, which is attributed to reduced exciton binding energy of the blend film. Also, the larger size grain formation with well-ordered stacking structure of the NIDCS-EO3 blend film leads to the increased charge mobility and thus to the improved charge mobility balance, resulting in higher JSC , FF, and PCE in the OSC device compared to those of a device using the hexyl chain-based NIDCS acceptor (NIDCS-HO). Finally, we fabricate NIDCS-EO3 devices with various commercial donors including P3HT, DTS-F, and PCE11 to show higher photovoltaic performance than the NIDCS-HO devices, suggesting versatility of NIDCS-EO3.

Structure and Dynamics of a Temperature-Sensitive Hydrogel.

Polyisocyanotripeptides (TriPIC) are biomimetic polymers which consist of a β-helical backbone stabilized by hydrogen bonds between amide groups. Their oligoethylene glycol side chains give aqueous TriPIC solutions a thermoresponsive behavior: at 50 °C the solution becomes a hydrogel. In this paper we study the molecular structure and water dynamics of TriPIC aqueous solutions while undergoing gelation using FT-IR spectroscopy and polarization-resolved femtosecond infrared spectroscopy (fs-IR). We find evidence that the oligoethylene glycol side chains trap part of the water molecules upon gel formation, and we propose that the interaction between the oligoethylene glycol side chains and water plays an essential role in the bundling of the polymers and thus in the formation of a hydrogel.

Globular Aggregates Stemming from the Self-Assembly of an Amphiphilic N-Annulated Perylene Bisimide in Aqueous Media.

Herein, we describe the synthesis of highly emissive amphiphilic N-annulated PBI 1 decorated with oligo ethylene glycol (OEG) side chains. These polar side chains allow the straightforward solubility of 1 in solvents of different polarity such as water, iPrOH, dioxane, or chloroform. Compound 1 self-assembles in aqueous media by π-stacking of the aromatic units and van der Waals interactions, favored by the hydrophobic effect. The hypo- and hypsochromic effect observed in the UV-Vis spectra of 1 in water in comparison to chloroform is diagnostic of H-type aggregation. Solvent denaturation experiments allow deriving the free Gibbs energy for the self-assembly process in aqueous media and the factor m that is indicative of the influence exerted by a good solvent in the stability of the final aggregates. The ability of compound 1 to self-assemble in water yields globular aggregates that have been visualized by TEM imaging.

Effect of Host-Guest Complexation on the Thermoresponsive Behavior of Poly(oligo ethylene glycol acrylate)s Functionalized with Dialkoxynapththalene Guest Side Chains.

The combination of thermoresponsive polymers with supramolecular host-guest interactions enables accurate tuning of the phase transition temperature, while also providing additional response mechanisms based on host-guest complexation. Most studies focused on a single thermoresponsive polymer to demonstrate the effect of host-guest complexation on the responsive behavior. In this work, the effect of the polymer structure on the host-guest complexation and thermoresponsive behavior is reported. Therefore, different poly(oligoethylene glycol acrylate)s, namely, poly(2-hydroxyethylacrylate) (PHEA), poly(methoxy diethylene glycol acrylate), poly(methoxy triethylene glycol acrylate), and poly(methoxy tetraethylene glycol acrylate), are synthesized functionalized with 1,5-dialkoxynaphthalene guest molecules in the side chain. Their complexation with the cyclobis(paraquat-p-phenylene) tetrachloride host is studied to understand the effect of polymer structure on the supramolecular association and the polymer phase transition, revealing that the oligoethylene glycol side chains lead to weaker host-guest complexation and also have a smaller increase in the cloud point temperature compared to PHEA.

N‐Type Rigid Semiconducting Polymers Bearing Oligo(Ethylene Glycol) Side Chains for High‐Performance Organic Electrochemical Transistors

AbstractN‐type conjugated polymers as the semiconducting component of organic electrochemical transistors (OECTs) are still undeveloped with respect to their p‐type counterparts. Herein, we report two rigid n‐type conjugated polymers bearing oligo(ethylene glycol) (OEG) side chains, PgNaN and PgNgN, which demonstrated an essentially torsion‐free π‐conjugated backbone. The planarity and electron‐deficient rigid structures enable the resulting polymers to achieve high electron mobility in an OECT device of up to the 10−3 cm2 V−1 s−1 range, with a deep‐lying LUMO energy level lower than −4.0 eV. Prominently, the polymers exhibited a high device performance with a maximum dimensionally normalized transconductance of 0.212 S cm−1 and the product of charge‐carrier mobility μ and volumetric capacitance C* of 0.662±0.113 F cm−1 V−1 s−1, which are among the highest in n‐type conjugated polymers reported to date. Moreover, the polymers are synthesized via a metal‐free aldol‐condensation polymerization, which is beneficial to their application in bioelectronics.

N‐Type Rigid Semiconducting Polymers Bearing Oligo(Ethylene Glycol) Side Chains for High‐Performance Organic Electrochemical Transistors

N-type conjugated polymers as the semiconducting component of organic electrochemical transistors (OECTs) are still undeveloped with respect to their p-type counterparts. Herein, we report two rigid n-type conjugated polymers bearing oligo(ethylene glycol) (OEG) side chains, PgNaN and PgNgN, which demonstrated an essentially torsion-free π-conjugated backbone. The planarity and electron-deficient rigid structures enable the resulting polymers to achieve high electron mobility in an OECT device of up to the 10-3 cm2 V-1 s-1 range, with a deep-lying LUMO energy level lower than -4.0 eV. Prominently, the polymers exhibited a high device performance with a maximum dimensionally normalized transconductance of 0.212 S cm-1 and the product of charge-carrier mobility μ and volumetric capacitance C* of 0.662±0.113 F cm-1 V-1 s-1 , which are among the highest in n-type conjugated polymers reported to date. Moreover, the polymers are synthesized via a metal-free aldol-condensation polymerization, which is beneficial to their application in bioelectronics.

Fullerene derivatives with oligoethylene-glycol side chains: an investigation on the origin of their outstanding transport properties.

For many years, fullerene derivatives have been the main n-type material of organic electronics and optoelectronics. Recently, fullerene derivatives functionalized with ethylene glycol (EG) side chains have been showing important properties such as enhanced dielectric constants, facile doping and enhanced self-assembly capabilities. Here, we have prepared field-effect transistors using a series of these fullerene derivatives equipped with EG side chains of different lengths. Transport data show the beneficial effect of increasing the EG side chain. In order to understand the material properties, full structural determination of these fullerene derivatives has been achieved by coupling the X-ray data with molecular dynamics (MD) simulations. The increase in transport properties is paired with the formation of extended layered structures, efficient molecular packing and an increase in the crystallite alignment. The layer-like structure is composed of conducting layers, containing of closely packed C60 balls approaching the inter-distance of 1 nm, that are separated by well-defined EG layers, where the EG chains are rather splayed with the chain direction almost perpendicular to the layer normal. Such a layered structure appears highly ordered and highly aligned with the C60 planes oriented parallel to the substrate in the thin film configuration. The order inside the thin film increases with the EG chain length, allowing the systems to achieve mobilities as high as 0.053 cm2 V−1 s−1. Our work elucidates the structure of these interesting semiconducting organic molecules and shows that the synergistic use of X-ray structural analysis and MD simulations is a powerful tool to identify the structure of thin organic films for optoelectronic applications.

Toughening of a Soft Polar Polythiophene through Copolymerization with Hard Urethane Segments.

Polar polythiophenes with oligoethylene glycol side chains are exceedingly soft materials. A low glass transition temperature and low degree of crystallinity prevents their use as a bulk material. The synthesis of a copolymer comprising 1) soft polythiophene blocks with tetraethylene glycol side chains, and 2) hard urethane segments is reported. The molecular design is contrary to that of other semiconductor‐insulator copolymers, which typically combine a soft nonconjugated spacer with hard conjugated segments. Copolymerization of polar polythiophenes and urethane segments results in a ductile material that can be used as a free‐standing solid. The copolymer displays a storage modulus of 25 MPa at room temperature, elongation at break of 95%, and a reduced degree of swelling due to hydrogen bonding. Both chemical doping and electrochemical oxidation reveal that the introduction of urethane segments does not unduly reduce the hole charge‐carrier mobility and ability to take up charge. Further, stable operation is observed when the copolymer is used as the active layer of organic electrochemical transistors.