Number Of Side Holes Research Articles

Evaluation of Recirculation During Venovenous Extracorporeal Membrane Oxygenation Using Computational Fluid Dynamics Incorporating Fluid-Structure Interaction.

Recirculation in venovenous extracorporeal membrane oxygenation (VV ECMO) leads to reduction in gas transfer efficiency. Studies of the factors contributing have been performed using in vivo studies and computational models. The fixed geometry of previous computational models limits the accuracy of results. We have developed a finite element computational fluid dynamics model incorporating fluid-structure interaction (FSI) that incorporates atrial deformation during atrial filling and emptying, with fluid flow solved using large eddy simulation. With this model, we have evaluated an extensive number of factors that could influence recirculation during two-site VV ECMO, and characterized their impact on recirculation, including cannula construction, insertion depth and orientation, VV ECMO configuration, circuit blood flow, and changes in volume, venous return, heart rate, and blood viscosity. Simulations revealed that extracorporeal blood flow relative to cardiac output, ratio of superior vena caval (SVC) to inferior vena caval (IVC) blood flow, position of the SVC cannula relative to the cavo-atrial junction, and orientation of the return cannula relative to the tricuspid valve had major influences (>20%) on recirculation fraction. Factors with a moderate influence on recirculation fraction (5%-20%) include heart rate, return cannula diameter, and direction of extracorporeal flow. Minimal influence on recirculation (<5%) was associated with atrial volume, position of the IVC cannula relative to the cavo-atrial junction, the number of side holes in the return cannula, and blood viscosity.

Impact of side-hole geometry on the performance of hemodialysis catheter tips: A computational fluid dynamics assessment.

Hemodialysis catheters are used to support blood filtration, yet there are multiple fundamentally different approaches to catheter tip design with no clear optimal solution. Side-holes have been shown to increase flow rates and decrease recirculation but have been associated with clotting/increased infection rates. This study investigates the impact of changing the shape, size and number of side-holes on a simple symmetric tip catheter by evaluating the velocity, shear stress and shear rate of inflowing blood. A platelet model is used to examine the residence time and shear history of inflowing platelets. The results show that side-holes improve the theoretical performance of the catheters, reducing the maximum velocity and shear stress occurring at the tip compared to non-side-hole catheters. Increasing the side-hole area improved performance up to a point, past which not all inflow through the hole was captured, and instead a small fraction slowly ‘washed-out’ through the remainder of the tip resulting in greater residence times and increasing the likelihood of platelet adhesion. An oval shaped hole presents a lower chance of external fibrin formation compared to a circular hole, although this would also be influenced by the catheter material surface topology which is dependent on the manufacturing process. Overall, whilst side-holes may be associated with increased clotting and infection, this can be reduced when side-hole geometry is correctly implemented though; a sufficient area for body diameter (minimising residence time) and utilising angle-cut, oval shaped holes (reducing shear stress and chances of fibrin formation partially occluding holes).

Drainage Performance of a Novel Catheter Designed to Reduce Drainage Catheter Failure

Abstract Objective Efficient flow of fluids through drainage/infusion catheters is affected by surrounding tissue, organ compression, and scar tissue development, limiting or completely obstructing flow through drainage holes. In this work, we introduce a novel three-dimensional (3D) drainage catheter with protected side holes to reduce flow blockages. We then compare its drainage performance to standard straight and pigtail catheters using computer-generated catheter designs and flow analysis software. Methods Drainage performance was computed as flow rate through the catheter for a given pressure differential. Each catheter contained drainage holes on the distal (insertion) end and a single outlet (hub) hole open to atmosphere. Computational fluid dynamics using ANSYS AIM 18.2 was used to simulate flow through the catheter and examine drainage performance based on variations to the following parameters: (1) side hole shape, (2) cross-sectional area of the catheters, (3) number of side holes, and (4) cross-sectional area of the side holes. Results Drainage through the newly introduced catheter in all simulations was nearly identical to standard pigtail and straight catheters. While working to optimize the 3D catheter design, we found that the changes in side hole shape and side hole cross-sectional area had little effect on the total flow rate through the catheters but had a large impact on flow rate through the side hole nearest to the hub (proximal hole). Additionally, the majority of flow in all catheters occurred at the most proximal 1 to 3 side holes closest to hub, with relatively little flow occurring at side holes more distally located (closest to insertion end). The 3D catheter demonstrated no changes in flow characteristics when the coiled segment was occluded, giving it an advantage over other catheter types when the catheter is compressed by surrounding tissue or other external obstruction. Conclusions The majority of fluid flow in catheters with a diameter of 4.67 mm (14 Fr) or smaller occurred at the most proximal 1 to 3 side holes. A novel 3D coiled catheter design can protect these proximal holes from external blockage while maintaining drainage performance compared with standard straight and pigtail catheters.

Influence of indwelling position and number of side holes on recirculation rate of dialysis blood in reversal connection of vascular access catheter

Influence of indwelling position and number of side holes on recirculation rate of dialysis blood in reversal connection of vascular access catheter

Convectively Dominated Heparin Leakage From Multiple Catheter Designs: An In Vitro Experimental Study.

Central venous catheters (CVCs) are routinely filled with a heparin lock while not in use to avoid thrombus formation near the tip. However, heparin leakage is known to occur, and the lock effectiveness remains in question. It was recently shown that convective fluxes from the blood flow in the host vein transport the majority of locking solution away from the tip of hemodialysis catheters immediately after instillation. Combined with the low diffusivity of heparin, this results in concentrations of heparin at the catheter tip that are orders of magnitude lower than at instillation for the majority of the interdialytic phase, diminishing the antithrombotic effectiveness of the lock. In this study, heparin losses from three different CVCs with different tip designs are measured in a pulsatile flow loop. Planar laser-induced fluorescence and particle image velocimetry measurements of heparin concentration and fluid velocity are recorded downstream of the catheters and combined to evaluate heparin losses from each of the different catheter designs. Additionally, locking solution losses are measured from one catheter (Hickman) subjected to three different flow conditions. Heparin losses are shown to depend weakly on flow condition but be highly dependent on catheter design. Convective losses from the Hickman catheter, with no side holes, are minimal (1-2%), although losses from the other two catheter types, both with a number of side holes, are significantly higher (7%). These results indicate the potential to maintain a high concentration of locking solution during the interdialytic phase with proper catheter design, particularly focusing on side hole distribution and shape.

Apical-Ventricular Cannula for Aortic Valve Bypass Therapy

A growing number of elderly patients with significant co-morbidities do not meet the inclusion criteria for conventional cardiac surgical therapies, including aortic valve replacement and mechanical circulatory support. To meet this clinical need, an aortic valve bypass (AVB) system is being developed that may be implanted using subcostal or mini-thoracotomy surgical approaches without ventricular coring or cardiopulmonary bypass. The AVB system consists of an apical left ventricular (ALV) cannula made from pyrolytic carbon, a valved conduit with a locking mechanism, and a Nitinol clip for anastomosis to the descending aorta. To define design criteria and demonstrate efficacy, ALV cannulae with different diameters (7–14 mm), number of sideholes (6–12), sidehole size (1.9–4.6 mm wide) and tip shapes (tapered, straight) were designed, fabricated, and tested. Cannula efficacy was determined by quantifying flow rates and pressure drops across the ALV cannula using steady-state and dynamic mock circulation models simulating mild, moderate and severe aortic stenosis test conditions. Blood trauma testing was conducted to demonstrate hemocompatibility using the smallest diameter (7 mm) ALV cannula prototype fabricated from pyrolytic carbon (PYC). In vitro and blood trauma testing demonstrated that (1) the 7 mm PYC cannula did not produce significant hemolysis ( 4.5 L/min for <10 mmHg pressure drop across the ALV cannula, and (3) the cannula tip shape did not significantly alter bypass flow rate or pressure drop. The ALV cannula may enable a minimally invasive surgical approach using a modified Seldinger’s technique for implantation in heart failure patients with aortic stenosis.

Effect of side holes in cervical fusion cages: a finite element analysis study

The objective of this study was to investigate the effect of side holes on the predicted von Mises stress levels in cervical spinal fusion cages subjected to compressive loading. Models with between zero and ten side holes were developed. Finite element analysis (FEA) was used to simulate compression of the cage, made from the polymer PEEK (polyetheretherketone), between two adjacent vertebrae. The analyses were validated by experimental tests. In all of the models, the von Mises stress was highest at the cage-vertebrae interface with peak stresses of between 14 and 18 MPa. Increasing the Young's modulus of the vertebrae from 12 to 30 GPa increased the peak stress on average by 29 per cent. The stresses in the models were lower than the compressive strength of PEEK (118 MPa), and are well within the PEEK fatigue strength reported (60 MPa at 10 million cycles). This study suggests that the number of side holes had a negligible effect on the stress distribution within the cage; the stress magnitudes were fairly constant across all of the models and did not change substantially with the number of holes. Hence, a cervical cage with side holes is unlikely to fail in compression.

Endoscopic stent exchange using a guide wire and mini-snare

Endoscopic placement of polyethylene stents is a well-established therapy for treatment of a variety of benign and malignant biliary tract diseases. Stent clogging by bacteria, bacterial biofilm, and biliary sludge is a major late complication affecting all kinds of plastic endoprostheses.1, 2 Efforts to prevent stent clogging utilizing long-term oral antibiotics, gallstone dissolution agents, choleretics, mucolytics, silver or antibiotic impregnation of stents and modification of stent size, shape, and number of sideholes have met with little success.3-6 The expandable metal stents have recently been evaluated because of problems with plastic stent occlusion. However, their inability to be removed nonsurgically, relative high cost, and the potential for occlusion by tumor ingrowth may limit application of the currently available expandable stents.7,8 Until modifications to prevent plastic stent occlusion are developed, such stents will need to be exchanged periodically. Standard practice has been to remove the old stent by grasping the intraduodenal portion with a snare, basket, or forceps and withdrawing the scope, depositing the stent in the stomach for later removal or pulling the stent through the biopsy channel. The bile duct is then recannulated and a fresh stent inserted. This approach risks loss of access to the obstructed segment, which is of particular concern in hilar tumors. A wire-guided metal spiral retrieval device9 and a hydrostatic balloon1o have been utilized to circumvent this problem. However, both add additional cost to the procedure and require perfect alignment of the retrieval device and stent for successful stent removal. We report a new simple stent retrieval technique that allows for maintenance of position in

Blood flow into vascular catheters of different size and number of sideholes. Model experiments with flush fluid injections.

Using an experimental model of the arterial circulation system, inflow of blood into polyethylene catheters following injection of contrast medium and isotonic saline solution was evaluated. The experiments included an analysis of the influence of density and viscosity of the flush solutions as well as the effect of catheters of different sizes with and without sideholes.