NSC KIPT Research Articles

INJECTION EFFICIENCY IN COMPTON RING NESTOR

NESTOR is the hard X-ray source that is under commissioning at NSC KIPT. NESTOR based on the Compton scattering of laser photons on relativistic electrons. The structure of the facility can be represented as the following components: a linear accelerator, a transport channel, a storage ring, and a laser-optical system. Electrons are stored in the storage ring for energy of 40-200 MeV. Inevitable alignment errors of magnetic elements are strongly effect on the beam dynamics in the storage ring. These errors lead to a shift of the equilibrium orbit relative to the ideal one. Significant shift of the equilibrium orbit could lead to loss of the beam on physical apertures. Transverse sizes of electron and laser beams are only few tens of microns at the interaction point. The shift of electron beam at the interaction point could greatly complicate the operation adjustment of storage ring without sufficient beam position diagnostic system. This article presents the simulation results of the efficiency of electron beam accumulation in the NESTOR storage ring. Also, this article is devoted to electron beam dynamics due to alignment errors of magnetic element in the ring.

REDESIGN OF NESTOR STORAGE RING LATTICE

NESTOR is the hard X-ray source that is under commissioning at NSC KIPT. NESTOR based on the Compton scattering of laser photons on relativistic electrons. The structure of the facility can be represented as the following components: a linear accelerator, a transport channel, a storage ring, and a laser-optical system. Electrons are stored in the storage ring for energy of 40-225 MeV, laser photons are accumulated in the optical resonator. The frequencies of laser and electron bunches are synchronized, the interaction point located in the optical resonator. The measurements showed that parameters of the manufactured bending magnets different from the design ones. The bending magnets have different field index, besides the vertical focusing forces are significantly lower than designed ones. The beam dynamics simulation showed that due to decreasing of the vertical focusing the vertical betatron frequency becomes close to the frequency of the integer resonance Q = 2, as a result the vertical motion in the ring is unstable [1]. The second reason for optimization is the need to increase the length of the drift space for optical resonator. The results of optimization are presented in this paper.

Получение высокочистых гранулированных металлов: кадмия, цинка, свинца

Cadmium, zinc and lead are constituent components of many semiconductor compounds. The obtained high purity distillates and ingots are large-size elements, which is not always convenient to use, and thus require additional grinding, which does not always allow maintaining the purity of the original materials. For the growth of semiconductor and scintillation single crystals it is advisable to use «friable» granular high-purity distillates, which can be processed without the risk of contamination. For example, the European low-background experiment LUCIFER required more than 20 kg of high-purity granulated zinc, which was agreed to be supplied by NSC KIPT. This task was then extended to cadmium and lead. Motivated by these tasks, the authors of this paper propose complex processes of deep refining of cadmium, zinc and lead by vacuum distillation. A device producing granules has been developed. The process of granulation of high-purity metals is explored. The purity of produced granules for cadmium and zinc is >99,9999, and >99,9995% for lead granules. To prevent oxidation of metal granules during exposition to air, chemical methods of surface passivation were used. Organic solvent based on dimethylformamide used as a coolant improves the resistance of granules to atmospheric corrosion during the granulation of high purity Cd, Zn and Pb.

Image quality method as a possible way of in situ monitoring of in-vessel mirrors in a fusion reactor.

The plasma-facing (first) mirrors in ITER will be subject to sputtering and/or contamination with rates that will depend on the precise mirror locations. The resulting influence of both these factors can reduce the mirror reflectance (R) and worsen the transmitted image quality (IQ). This implies that monitoring the mirror quality in situ is an actual desire, and the present work is an attempt towards a solution. The method we propose is able to elucidate the reason for degradation of the mirror reflectance: sputtering by charge exchange atoms or deposition of contaminated layers. In case of deposition of contaminants, the mirror can be cleaned in situ, but a rough mirror (due to sputtering) cannot be used anymore and has to be replaced. To demonstrate the feasibility of the IQ method, it was applied to mirror specimens coated with carbon film in laboratory conditions and to mirrors coated with contaminants during exposure in fusion devices (TRIAM-1M and Tore Supra), as well as to mirrors of different materials exposed to sputtering by plasma ions in the DSM-2 plasma stand (in IPP NSC KIPT).

Reaction rates of the 113In(γ,n)112mIn and 115In(γ,n)114mIn

The integral yields of the 113In(γ,n)112mIn (Jπ=9/2+→Jπ=4+) and 115In(γ,n)114mIn (Jπ=9/2+→Jπ=5+) photonuclear reactions were measured in the bremsstrahlung end-point energy range from the respective thresholds up to 14 MeV by a conventional activation/decay technique using the 197Au(γ,n)196Au reaction cross sections as the standard for the absolute photon intensity determination. The metallic indium samples of the natural and enriched compositions were irradiated by the bremsstrahlung beams from thin tantalum converters of the electron linear accelerator of NSC KIPT (Kharkiv) and the microtron of IEP (Ughhorod). The integral reaction yields were determined from the activities of the nuclei-products measured by the high resolution γ-ray spectrometry technique with Ge(Li)- and HPGe-detectors. The reaction rates for the Planck spectrum of a thermal photon bath were derived for the ground state target nuclei and compared to the predictions of the statistical model of nuclear reactions.

Accelerating structure design and fabrication for KIPT and PAL XFEL

ANL (Argonne National Laboratory) and the National Science Center “Kharkov Institute of Physics Technology” (NSC KIPT, Kharkov, Ukraine) jointly propose to design and build a 100 MeV/100 kW linear accelerator which will be used to drive the neutron source subcritical assembly. The linac has almost finished assembly in KIPT by a team from the Institute of High Energy Physics (IHEP, Beijing, China). The design and measurement result of the accelerating system of the linac will be described in this paper.

Electron gun system for NSC KIPT linac

In the NSC KIPT linac, a neutron source based on a subcritical assembly driven by a 100 MeV/100 kW electron linear accelerator is under design and development. The linear accelerator needs a new high current electron gun. In this paper, the physical design, mechanical fabrication and beam test of this new electron gun are described. The emission current is designed to be higher than 2 A for the pulse width of 3 μs with repetition rate of 50 Hz. The gun will operate with a DC high voltage power supply that can provide a high voltage up to 150 kV. Computer simulations and optimizations have been carried out in the design stage, including the gun geometry and beam transport line. The test results of high voltage conditioning and beam test are presented. The operation status of the electron gun system is also included. The basic test results show that the design, manufacture, and operation of the new electron system are basically successful.

Progress on the construction of the 100 MeV/100 kW electron linac for the NSC KIPT neutron source

IHEP, China is constructing a 100 MeV/100 kW electron Linac for NSC KIPT, Ukraine. This linac will be used as the driver of a neutron source based on a subcritical assembly. In 2012, the injector part of the accelerator was pre-installed as a testing facility in the experimental hall #2 of IHEP. The injector beam and key hardware testing results met the design goal. Recently, the injector testing facility was disassembled and all of the components for the whole accelerator have been shipped to Ukraine from China by the ocean shipping. The installation of the whole machine in KIPT will be started in June, 2013. The construction progress, the design and testing results of the injector beam and key hardware are presented.

Beam dynamics studies on the 100 MeV/100 kW electron linear accelerator for NSC KIPT neutron source

We designed a 100 MeV/100 kW electron linear accelerator for NSC KIPT, which will be used to drive a neutron source on the basis of subcritical assembly. Beam dynamics studies have been conducted to reach the design requirements (E = 100 MeV, P = 100 kW, dE/E < 1% for 99% particles). In this paper, we will present the progress of the design and the dynamic simulation results. For high intensity and long beam pulse linear accelerators, the BBU effect is one big issue; special care has been taken in the accelerating structure design. To satisfy the energy spread requirement at the linac exit, the particles with large energy difference from the synchronous particle should be eliminated at a low energy stage to ease the design of the collimation system and radiation shielding. A dispersion free chicane with 4 bending magnets is introduced downstream of the 1st accelerating section; the unwanted particles will be collimated there.

RF-thermal-structural-RF coupled analysis on a travelling wave disk-loaded accelerating structure

The travelling wave (TW) disk-loaded accelerating structure is one of the key components in normal conducting (NC) linear accelerators, and has been studied for many years. In the design process, usually after the dimensions of each cell and the two couplers are finalized, the structure is fabricated and tuned, and then the whole structure RF characteristics are measured by using a vector network analyzer. Before fabrication, the whole structure characteristics (including RF, thermal and structural ones) are less simulated due to the limited capability of currently available computers. In this paper, we described a method for performing RF-thermal-structural-RF coupled analysis on a TW disk-loaded structure using only one PC. In order to validate our method, we first analyzed and compared our RF simulation results on the 3 m long BEPC II structure with the corresponding experimental results, which shows very good consistency. Finally, the RF-thermal-structure-RF coupled analysis results on the 1.35 m long NSC KIPT linac accelerating structure are presented.

Carrier-free production of 95Tc at an electron accelerator

We report on the results of studies of the 95Tc isotope production conditions in a poorly investigated 96Ru(γ,N) 95Tc reaction at a relatively inexpensive electron accelerator. Based on the analytical model it is demonstrated the possibility for estimating the effective and peak cross-sections and the isotope yield for a given reaction in a thick production target without preliminary determination of its excitation function. For this purpose we compared specific activities of two small samples that were activated under the same conditions using the reference reaction 68Zn(γ,p) 67Cu and the one under investigation. The experiment on simultaneous photo-activation of natural zinc and ruthenium targets was performed followed by the investigation of their isotope composition. The specific activity of the radionuclide was measured and cross-sections for the 96Ru(γ,N) 95g,mTc reactions were determined. The yields of desired isomers and admixtures in the natural ruthenium targets of different size were estimated. It is shown, in particular, that the operating conditions of the NSC KIPT accelerator KUT-30 can provide 95gTc yields up to 120 mCi/h.

The development of a TESLA recirculator with superconducting accelerating structures in Ukraine

The recirculator project, which is to be built at the National Science Center, Kharkov Institute of Physics and Technology (NSC KIPT), is presented. The basic solutions incorporated in the design are given. The TESLA superconducting section is chosen as the accelerating structure of an accelerating complex.

The use of linear superconducting electron accelerator for subcritical reactor driving

At the National Science Centre, Kharkiv Institute of Physics and Technology (NSC KIPT) the possibility of creating an installation with a subcritical reactor driven by an electron accelerator is examined. To obtain the maximal stream of neutrons from a neutron-producing target at a minimal density of energy emission, the electron energy should be in the range of 100-200 MeV and the size of the target should be as large as possible. Other important requirements are beam continuity with time and long-term stability of the accelerator parameters. The variants of using the superconducting linear accelerator on the basis of a TESLA accelerating structure as of subcritical reactor driver are considered. The basic design parameters and characteristics of this installation are presented.

Lattice of NSC KIPT compact intense X-ray generator NESTOR

The new generation of the intense X-ray sources based on low-energy electron storage ring and Compton scattering (CS) of laser beam allows to produce X-rays with intensity up to 10 14 phot/s. There are two basic problems in laser–electron storage rings (LESR) design. The first one is associated with strong effect of the intrabeam scattering at low electron beam energy. Because of this effect, the beam size grows quickly and CS intensity decreases. The second problem is associated with large electron beam energy spread because of fluctuation of Compton generation. The value of the energy spread may run up to few percents and one has to keep electron beam during long term in order to achieve the high Compton beam intensity. The paper is devoted to the description of lattice of NSC KIPT compact intense X-ray generator NESTOR and the main principles are background for the LESR lattice design.

Results of participation of NSC KIPT in the CERN/CMS Monte-Carlo event Production

The hardware configuration and cluster software of the NSC KIPT specialized Linux cluster constructed for carrying out work on CMS physics simulations and data processing are described. The performances and architecture of the cluster are outlined. The results of participation of NSC KIPT in the CERN/CMS Monte-Carlo event production arc presented.