Non-thermal Dielectric Barrier Discharge Plasma Research Articles

Synergistic effect on simultaneous treatment of Cr(VI) and chloramphenicol using a non-thermal plasma technology

Toxic organic and heavy metal contaminants commonly exist in industrial waste stream and the treatment is of great challenge. In this study, a dielectric barrier discharge (DBD) non-thermal plasma was employed for the simultaneous treatment of two important contaminants, chloramphenicol (CAP) and Cr(VI) in an aqueous solution through redox transformations. More than 70% of CAP and 20% of TOC were degraded in 60 min, while Cr(VI) was completely removed in 10 min. The hydroxyl radicals could be the main active species for the degradation. Meanwhile, the consumption of hydroxyl radicals was beneficial to the reduction of Cr(VI). The synergistic effect was investigated between CAP degradation and Cr(VI) reduction. The reduction of Cr(VI) would be enhanced in the presence of CAP with a low concentration and could be inhibited under a high concentration of CAP, because part of hydroxyl radicals could be consumed by a low concentration of CAP and the obtained intermediates with a higher kinetic rate. However, CAP with a high concentration could also react with some reductive species, such as eaq- and •H, which could compete with Cr(VI) and inhibit the reduction of Cr(VI). In addition, the presence of Cr(VI) could enhance the degradation and mineralization of CAP, and the identification of obtained intermediates indicated that the presence of Cr(VI) could change the degradation path of CAP as Cr(VI) would react with reductive species and enhance the generation of hydroxyl radicals, leading to more hydroxylation reactions. Moreover, the mechanism for the simultaneous redox transformations of CAP and Cr(VI) was illustrated. This study indicates that the DBD non-thermal plasma technology could be one of better solutions for simultaneous elimination of heavy metal and organic contaminants in aquatic environment.

Degradation of 2,4-dinitrotoluene in aqueous solution by dielectric barrier discharge plasma combined with Fe–RGO–BiVO4 nanocomposite

2,4-Dinitrotoluene (2,4-DNT) as a priority and hazardous pollutant, is widely used in industrial and military activities. In this study the synergistic effect of Fe–RGO–BiVO4 nanocomposite in a non-thermal dielectric barrier discharge plasma reactor (NTP-DBD) for degrading 2,4-DNT was evaluated. Preparation of the Fe–RGO–BiVO4 nanocomposite was done by a stepwise chemical method depositing Fe and reduced graphene oxide (RGO) on BiVO4. Field emission scanning electron microscopy (FESEM), X-ray diffraction analysis (XRD), UV–vis diffuse reflectance spectra (DRS), and energy-dispersive X-ray spectroscopy mapping (EDS-mapping) validated the satisfactory synthesis of Fe–RGO–BiVO4. To find the optimal conditions and to determine the interaction of model parameters, a central composite design (RSM-CCD) had been employed. 2,4 DNT can be completely degraded at: initial 2,4-DNT concentration of 40 mg L−1, Fe–RGO–BiVO4 dosage of 0.75 g L−1, applied voltage of 21kV, reaction time of 30 min and pH equal to 7, while the single plasma process reached a degradation efficiency of 67%. The removal efficiency of chemical oxygen demand (COD) and total organic carbon (TOC) were 90.62% and 88.02% at 30 min contact time, respectively. Results also indicated that average oxidation state (AOS) and carbon oxidation state (COS) were enhanced in the catalytic NTP-DBD process, which demonstrate the effectiveness of proposed process for facilitating biodegradability of 2,4-DNT.

Improving the Quality of Bio-oil Using the Interaction of Plastics and Biomass through Copyrolysis Coupled with Nonthermal Plasma Processing.

Bio-oil produced from the pyrolysis of biomass is chemically complex, viscous, highly acidic, and highly oxygenated. Copyrolysis of biomass and plastics can enhance oil quality by raising the H/C ratio, leading to improved biofuel properties. In this work, copyrolysis of polystyrene and biomass was passed to a second-stage dielectric barrier discharge nonthermal plasma reactor with the aim to further improve the product bio-oil. Pyrolysis of the polystyrene and biomass produces volatiles that pass to the second stage to undergo cracking and autohydrogenation reactions under nonthermal plasma conditions. There was a synergistic interaction between biomass and polystyrene in terms of overall oil and gas yield and composition even in the absence of the nonthermal plasma. However, the introduction of the nonthermal plasma produced a marked increase in monocyclic aromatic hydrocarbons (e.g., ethylbenzene), whereas polycyclic aromatic compounds decreased in concentration. Most notably, the influence of the plasma markedly reduced the quantity of oxygenated compounds in the product oil. It is suggested that the unique reactive environment produced by the plasma involving high-energy electrons, excited radicals, ions, and intermediates increases the interaction of the polystyrene and biomass pyrolysis volatiles. Increasing input plasma power from 50 to 70 W further enhanced the effects of the nonthermal plasma.

Non-thermal plasma promotes boar sperm quality through increasing AMPK methylation

Boar sperm quality, as an important indicator of reproductive efficiency, directly affects the efficiency of livestock production. Here, this study was conducted to improve the boar sperm quality by using a non-thermal dielectric barrier discharge (DBD) plasma. Our results showed that DBD plasma exposure at 2.1 W for 15 s could improve boar sperm quality by increasing exon methylation level of adenosine monophosphate-activated protein kinase (AMPK) and thus improving the glycolytic flux, mitochondrial function, and antioxidant capacity without damaging the integrity of sperm DNA and acrosome. In addition, DBD plasma could rescue DNA methyltransferase inhibitor decitabine-caused low sperm quality through reducing the oxidative stress and mitochondrial damage. Therefore, the application of non-thermal plasma provides a new strategy for reducing sperm oxidative damage and improving sperm quality, which shows a great potential in assisted reproduction to solve the problem of male infertility.

Effect of biomass adsorbent on non-thermal plasma activated treatment of oil-based drilling cutting: Residual toxicity assessment

The oil-based drilling cutting (OBDC), which contain petroleum hydrocarbons produced during the oil and shale gas exploration process, are considered toxic solid waste for the environment. In this study, we introduce a promising technique by coupling non-thermal dielectric barrier discharge (DBD) plasma with biomass adsorbents (wheat stalk, straw fiber, or rice husk) to remove toxic compounds from OBDC. The results show the plasma treatment can achieve up to 90.9% degradation rate of total petroleum hydrocarbons (TPH). The introduction of 3 wt% of biomass adsorbent exhibited a significant enhancement of the energy efficiency (up to 21.9% increase using rice husk). Importantly, toxicity evaluations, such as the corn seed germination test, demonstrate a substantial reduction in the toxicity of drilling cuttings after plasma treatment, with seed germination and growth rates (using straw fiber) comparable to uncontaminated soil. Adding biomass adsorbents can also enhance the hydrophilicity of treated OBDC, increasing the presence of HCOO–, CH3HCOO–, NO3- species which further contributes to the safety and fertility of treated OBDC. Coupling non-thermal DBD plasma discharge with biomass adsorbents presents an efficient and environmentally friendly choice for the environmental treatment of OBDC in deep shale gas development.

A review on dielectric barrier discharge nonthermal plasma generation, factors affecting reactive species, and microbial inactivation

Nonthermal plasma treatment has been proven effective in decontaminating microorganisms in various foods on a laboratory scale. Various techniques for creating plasma have been investigated extensively due to their potential application in multiple settings; one of these methods is dielectric barrier discharge. This article summarizes our current understanding of plasma physics, different methods for producing plasma, the resulting reactive species, and their role in microbial degradation. The effect of plasma treatment on the inactivation of microorganisms is discussed, along with the intrinsic and extrinsic factors involved. In addition, the use of dielectric barrier discharge plasma in microbial destruction in various foods, as well as the effect of the treatment on other relevant properties, is also addressed.

Effect of dielectric barrier discharge nonthermal plasma treatment on physicochemical, nutritional, and phytochemical quality attributes of pineapple [Ananas comosus (L.)] juice.

Forward feed multilayered perception and central composite rotatable design were used to model the nonthermal plasma (NTP) experimental data in artificial neural network (ANN) and response surface methodology, respectively. The ANN was found to be more accurate in modeling the experimental dataset. The NTP process parameters (voltage and time) were optimized for pineapple juice within the range of 25-45kV and 120-900s using an ANN coupled with the genetic algorithm (ANN-GA). After 176 generations of GA, the ANN-GA approach produced the optimal condition, 38kV and 631s, and caused the inactivation of peroxidase (POD) and bromelain by 87.24% and 51.04%, respectively. However, 100.32% of the overall antioxidant capacity and 89.96% of the ascorbic acid were maintained in the optimized sample with a total color change (ΔE) of less than 1.97 at all plasma treatment conditions. Based on optimal conditions, NTP provides a sufficient level of POD inactivation combined with excellent phenolic component extractability and high antioxidant retention. Furthermore, plasma treatment had an insignificant effect (p>0.05) on the physicochemical attributes (pH, total soluble solid, and titratable acidity) of juice samples. From the intensity peak of the Fourier-transform infrared spectroscopy analysis, it was found that the sugar components and phenolic compounds of plasma-treated juice were effectively preserved compared to the thermal-treated juice.

The changed multiscale structures of tight nut (Cyperus esculentus) starch decide its modified physicochemical properties: The effects of non-thermal and thermal treatments

Non-thermal dielectric barrier discharge plasma (DBDP) and four thermal treatments, including baking (BT), high pressure cooking (HPC), radio frequency (RF) and microwave (MW) were applied to modify the structural and physicochemical properties of Cyperus esculentus starch (CES). The results showed that the thermal treatments remarkably disordered the crystalline structures of CES through weakening the double-helix conformation of amylopectin, while DBDP caused much more gentle influence on the starch structures than them. Specifically, MW induced the high-frequency displacement of polar molecules and intensive collisions between starch and water molecules, causing the largest stretching and swelling extents of amylopectin, resulting in the highest pasting and rheological viscosity of CES in four thermal treatments. As DBDP did not favor the aggregation of amylopectin chains, the deaggregated starch chains promoted the hydration effects with water molecules, boosting the final pasting viscosity, apparent rheological viscosity, freeze-thaw stability and digestion velocity of CES. Besides, the gelatinization-retrogradation process in the thermal treatments regulated starch digestion velocity and produced type III resistant starch in CES. Conclusively, the modified physicochemical properties of CES resulted from the altered molecular structures of starch by the applied treatments.

Efficient degradation and mineralization of aniline in aqueous solution by new dielectric barrier discharge non-thermal plasma

Aniline is a priority pollutant that is unfavorable to the environment and human health due to its carcinogenic and mutagenic nature. The performance of the dielectric barrier discharge reactor was examined based on the aniline degradation efficiency. Different parameters were studied and optimized to treat various wastewater conditions. Role of active species for aniline degradation was investigated by the addition of inhibitors and promoters. The optimum conditions were 20 mg/L initial concentration, 1.8 kV applied voltage, 4 L/min gas flow rate and a pH of 8.82. It was observed that 87% of aniline was degraded in 60 min of dielectric barrier discharge treatment at optimum conditions. UV–Vis spectra showed gradual increase in the treatment efficiency of aniline with the propagation of treatment time. Mineralization of AN was confirmed by TOC measurement and a decrease in pH during the process. To elicit the aniline degradation route, HPLC and LC-MS techniques were used to detect the intermediates and byproducts. It was identified that aniline degraded into different organic byproducts and was dissociated into carbon dioxide and water. Comparison of the current system with existing advanced oxidation processes showed that DBD has a remarkable potential for the elimination of organic pollutants.

Improving Printability of Polytetrafluoroethylene (PTFE) with the Help of Plasma Pre-Treatment.

Polytetrafluoroethylene (PTFE) is a potential candidate for the fabrication of flexible electronics devices and electronics with applications in various extreme environments, mainly due to its outstanding chemical and physical properties. However, to date, the utilization of PTFE in printing trials has been limited due to the material's low surface tension and wettability, which do not ensure good adhesion of the printing ink at the level of the substrate. Within this paper, successful printing of PTFE is realized after pre-treating the surface of the substrate with the help of dielectric barrier discharge non-thermal plasma. The efficiency of the pre-treatment is demonstrated with respect to both silver- and carbon-based inks that are commercially available, and finally, the long-lasting pre-treatment effect is demonstrated for periods of time spanning from minutes to days. The experimental results are practically paving the way toward large-scale utilization of PTFE as substrate in fabricating printed electronics in harsh working environments. After 3 s of plasma treatment of the foil, the WCA decreased from approximately 103° to approximately 70°. The resolution of the printed lines of carbon ink was not time dependent and was unmodified, even if the printing was realized within 1 min from the time of applying the pre-treatment or 10 days later. The evaluation of the surface tension (σ) measured with Arcotest Ink Pink showed an increase in σ up to 40 < σ < 42 mN/m for treated Teflon foil and from σ < 30 mN/m corresponding to the untreated substrate. The difference in resolution was distinguishable when increasing the width of the printed lines from 500 μm to 750 μm, but when increasing the width from 750 μm to 1000 μm, the difference was minimal.

Non-thermal plasma catalytic dry reforming of methane over Ni-Co3O4 supported modified-titania catalysts: Effect of process conditions on syngas production

The dry reforming of methane has been studied over modified TiO2-supported 10%Ni-5%Co3O4 composite catalysts using a non-thermal plasma dielectric barrier discharge fixed-bed reactor. The 10%Ni-5%Co3O4/modified-TiO2 nanorods (NR) have been synthesized by hydrothermal method. Physicochemical characterizations of the composite catalysts have been conducted by X-ray diffraction (XRD), H2 temperature-programmed reduction (H2-TPR), CO2 temperature-programmed desorption (CO2-TPD), high-resolution transmission electron microscopy (HRTEM) and N2 adsorption-desorption (BET) analysis. Incorporation of cubic-structured Co3O4 into Ni/TiO2 attributes to the enhancement of basicity, reducibility and metal-support interaction. Consequently, the catalytic activity of 10%Ni-5%Co3O4/TiO2 NR increases and confer CH4 and CO2 conversions at 86.4% and 84.9%, respectively. Meanwhile, the H2 and CO selectivity are reported as 50.1% and 49.0% respectively. Higher syngas ratio (H2/CO) from 0.84 to 1.01 and 26% increment in overall energy efficiency compared to plasma DRM alone have been observed. The superior plasma DRM performance is correlated to the greater basicity properties and the synergistic effect of non-thermal plasma with the 10%Ni-5%Co3O4/modified-TiO2 catalyst composite.

Hierarchical Structures Formed in an Atmospheric Pressure Plasma Jet by Polymerization from an Aerosol of Oxalic Acid Stabilized WO3–x Nanosheet Colloids: Toward High-Performance Electrochemical Devices and Sensors

The development of microstructures which combine high total surface area and high porosity is crucial for technologies such as electrocatalysis, electrochromics, and sensors. High deposition rate, composition control of deposition, and low processing temperature to retain active compositions are also desirable. To this end, this study describes combining colloidal sol chemistry with a nonthermal atmospheric pressure dielectric barrier discharge plasma jet to print hybrid inorganic/organic tungsten trioxide/oxalic acid (WO3–x/OA) microspheres. Injection of an aerosol of oxalic acid stabilized colloidal tungstic acid into an atmospheric pressure plasma jet results in the deposition of spherical structures in which the colloid is trapped within a plasma-polymerized organic shell. Subsequent low-temperature sintering produces hierarchical spherical shell-like structures comprising tungsten oxide nanosheets. Alteration of the gas flow rate changes the composition of the deposited material. The method has promise for the general preparation from colloidal precursors of porous materials of controlled morphology and composition with hierarchical microstructures, such as are required for applications in electrochemical devices and sensors which need a high ratio of surface area to volume and connectivity throughout the structure, yet also need a microstructure which is open for rapid exchange of reactants.

Effect of non-thermal plasma dielectric barrier discharge reactor on the quality of biomass gasification product gas from the gasifier

The primary goal of this research is to determine the effect of key processing parameters of dielectric barrier discharge (DBD) reactor on the components concentration of the fuel gas produced during the biomass gasification. By changing key processing parameters such as plasma input power, flow rate, and temperature, the performance of the DBD reactor is assessed. When the power is increased from 5 to 40 W, the concentrations of CO2 and H2 decrease to 12.9% and 18.5%, respectively, while the concentration of CO increases to 17.2%. At 40 W and 65 ml/min, the amount of tar compound significantly drops from 33 g/Nm3 to less than 1 g/Nm3. However, as input power increases, the concentration of C1–C5 hydrocarbons also tends to rise. The highest concentration of C1–C5 was around 0.60% at 40 W. As the flow rate increases, the concentration of CO2 increases while the concentration of CO tends to decrease at all measured power levels, the maximum concentration of CO2 was at 120 ml/min, whereas the minimum concentration of CO is seen under same conditions. With an increase in flow rate, the concentration of CH4 shows a decreasing tendency. It is seen that at 40 W, the concentration of CO and H2 drops as the temperature rises up to 400 °C. In contrast, there is a rising trend in the concentration of CO2, CH4, and tar compounds while increasing temperature. Hence, the DBD reactor appears to have a profound influence on a gas component produced during biomass gasification.

Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification

A nonthermal atmospheric plasma reactor was used to sterilize polymer surfaces and satisfy safety constraints in a biological medium. A 1D fluid model was developed using COMSOL Multiphysics software® 5.4 with a helium-oxygen mixture at low temperature for the decontamination of bacteria on polymer surfaces. An analysis of the evolution of the homogeneous dielectric barrier discharge (DBD) was carried out through studying the dynamic behavior of the discharge parameters including the discharge current, the consumed power, the gas gap voltage, and transport charges. In addition, the electrical characteristics of a homogeneous DBD under different operating conditions were studied. The results shown that increasing voltage or frequency caused higher ionization levels and maximum increase of metastable species' density and expanded the sterilization area. On the other hand, it was possible to operate plasma discharges at a low voltage and a high density of plasma using higher values of the secondary emission coefficient or permittivity of the dielectric barrier materials. When the discharge gas pressure increased, the current discharges declined, which indicated a lower sterilization efficiency under high pressure. A short gap width and the admixture of oxygen were needed for sufficient bio-decontamination. Plasma-based pollutant degradation devices could therefore benefit from these results.

Non-thermal plasma dielectric barrier discharge reactor stability analysis using fiber bragg grating sensor

The main focus in this study is to determine the stability of the plasma generated by a Dielectric Barrier Discharge (DBD) reactor in the presence and without glass beads as dielectric enhancement. The stability of plasma was determined based on plasma temperature which measured within plasma stream. The DBD plasma reactor was designed, fabricated and being operated in an open air system. Fiber Bragg grating (FBG) was used to measure the plasma temperature. The applied voltage was increased up to 8 kV to determine breakdown voltage and evaluate plasma stability with and without the presence of glass beads as dielectric enhancement. Experimental results revealed that plasma started to generate at applied voltage about 3.0 kV. Plasma formation found generated with stable at applied voltage 8 kV for both with and without the presence of glass beads. With the presence of glass beads, the plasma temperature found much higher about 180 °C compare with without glass beads which is about 90 °C, and yet the plasma generation is still stable.

The catalytic efficiency of Ru/Mn/Ce-Al2O3 in the reduction of HCN in dry methane reforming with CO2 assisted by non-thermal plasma

This study investigates the catalytic activity of Ru/Mn/Ce-Al2O3 in eliminating HCN via dry reforming CH4 with CO2 in the packed-bed dielectric barrier discharge non-thermal plasma (DBD NTP). A packed bed DBD configuration method was carried out in the non-thermal plasma with Ru/Mn/Ce-Al2O3 catalyst, whereby BaTiO3 beads was the dielectric medium. The carrier gas for dry methane reforming was N2, the peak-to-peak voltage was 24 kV and the total flow rate was 100 sccm with a ratio of 5:5:90 (CH4:CO2:N2), respectively. Gaseous products and by-products were analysed by Fourier transform infra-red (FTIR) spectroscopy. Experimental results revealed that Ru/Mn/Ce-Al2O3 catalyst could eliminate HCN at approximately 82% and had a low selectivity in decomposing NH3. Besides, the conversion of CH4 achieved was approximately 68%.

Potential of Nonthermal Atmospheric-Pressure Dielectric Barrier Discharge Plasma for Inhibition of Athelia rolfsii Causing Southern Blight Disease in Lettuce

Athelia rolfsii is one of the most destructive and aggressive fungal pathogens worldwide and causes southern blight disease of lettuce. A nonthermal atmospheric-pressure dielectric barrier discharge (DBD) plasma has attracted interest as an alternative control method to chemical usage because of its antimicrobial activity. Exposure of A. rolfsii to DBD plasma for 5, 10, 15, and 20 min resulted in in vitro fungal inhibition of mycelial discs and sclerotia. The results showed that DBD plasma exposure for 10 min completely inhibited fungal growth of mycelial discs, whereas exposure for over 20 min was required to inhibit the hyphal growth of sclerotia. Scanning electron microscopy (SEM) observations of mycelia and sclerotia abnormalities revealed laceration and damage of both mycelia and sclerotia. In addition, disease incidence and severity were reduced in mycelial and sclerotia inoculation following DBD plasma exposure for 15 and 20 min, respectively, compared with the positive control. In conclusion, the DBD plasma demonstrates antifungal activity against A. rolfsii via inhibition of fungal growth and reduction in disease incidence and severity. Therefore, DBD plasma has the potential to be applied in controlling southern blight disease of lettuce.

Dielectric barrier discharge plasma catalysis as an alternative approach for the synthesis of ammonia: a review.

Numerous researchers have attempted to provide mild reactions and environmentally-friendly methods for NH3 synthesis. Research on non-thermal plasma-assisted ammonia synthesis, notably the atmospheric-pressure nonthermal plasma synthesis of ammonia over catalysts, has recently gained attention in the academic literature. Since non-thermal plasma technology circumvents the existing crises and harsh conditions of the Haber-Bosch process, it can be considered as a promising alternative for clean synthesis of ammonia. Non-thermal dielectric barrier discharge (DBD) plasma has been extensively employed in the synthesis of ammonia due to its particular advantages such as the simple construction of DBD reactors, atmospheric operation at ambient temperature, and low cost. The combination of this plasma and catalytic materials can remarkably affect ammonia formation, energy efficiency, and the generation of by-products. The present article reviews plasma-catalysis ammonia synthesis in a dielectric barrier discharge reactor and the parameters affecting this synthesis system. The proposed mechanisms of ammonia production by this plasma catalysis system are discussed as well.

수중 비열 유전체장벽 방전 플라즈마로 처리한 양식장 배출수의 수질 변화 특성

The purpose of this study is to evaluate the effects of underwater non-thermal Dielectric Barrier Discharge Plasma(DBD plasma) on fish farm effluent. This experiment was conducted in the DBD plasma generator, and the voltages given to generate DBD plasma were 11.6 kV and 23.1 kV. The measurement intervals were 0, 1, 5, 10 and 15 minutes. As a result of the experiment, the change in water quality was proportional to the strength of the voltage and the treatment time. At 23.1 kV for 15 minutes, the water temperature was increased to 51.1%, the pH was decreased by 26.2%, the dissolved oxygen was reduced to 50.3%, the chemical oxygen demand was reduced to 19.1% and the suspended solids was decreased 17.9%. NH₄SUP+/SUP-N was decreased by 95.8%, while NO₂SUP-/SUP-N and NO₃SUP-/SUP-N were increased by 851.8% and 170.2%. The total bacteria number contained in the discharge water was removed 100% at 23.1 kV for 15 minute, and the coliform group was sterilized up to 100% at 23.1 kV for 10 minute. The DBD plasma technology was found to reduce the organic pollutants and have high sterilization power against microorganisms in fish farm effluent.

Bioactive Nonthermal Biocompatible Plasma Enhances Migration on Human Gingival Fibroblasts.

This study hypothesizes that the application of low-dose nonthermal biocompatible dielectric barrier discharge plasma (DBD-NBP) to human gingival fibroblasts (HGFs) will inhibit colony formation but not cell death and induce matrix metalloproteinase (MMP) expression, extracellular matrix (ECM) degradation, and subsequent cell migration, which can result in enhanced wound healing. HGFs treated with plasma for 3min migrate to each other across the gap faster than those in the control and 5-min treatment groups on days 1 and 3. The plasma-treated HGFs show significantly high expression levels of the cell cycle arrest-related p21 gene and enhanced MMP activity. Focal adhesion kinase (FAK) mediated attenuation of wound healing or actin cytoskeleton rearrangement, and plasma-mediated reversal of this attenuation support the migratory effect of DBD-NBP. Further, this work performs computer simulations to investigate the effect of oxidation on the stability and conformation of the catalytic kinase domain (KD) of FAK. It is found that the oxidation of highly reactive amino acids (AAs) Cys427, Met442, Cys559, Met571, Met617, and Met643 changes the conformation and increases the structural flexibility of the FAK protein and thus modulates its function and activity. Low-dose DBD-NBP-induces host cell cycle arrest, ECM breakdown, and subsequent migration, thus contributing to the enhanced wound healing process.