Non-thermal Atmospheric Plasma Research Articles

Experimental investigation on electrical characteristics and dose measurement of dielectric barrier discharge plasma device used for therapeutic application.

In this research, a Dielectric Barrier Discharge (DBD) plasma device operating in air has been made. The electrical characteristics of this device like instantaneous power, dissipated power, and discharge capacitance have been measured. Also, the effects of applied voltage on the dissipated power and discharge capacitance of the device have been investigated. The determination of electrical parameters is important in DBD plasma device used in living tissue treatment for choosing the proper treatment doses and preventing the destructive effects. The non-thermal atmospheric pressure DBD plasma source was applied for studying the acceleration of blood coagulation time, in vitro and wound healing time, in vivo. The citrated blood drops coagulated within 5 s treatment time by DBD plasma. The effects of plasma temperature and electric field on blood coagulation have been studied as an affirmation of the applicability of the constructed device. Also, the effect of constructed DBD plasma on wound healing acceleration has been investigated.

Direct protein introduction into plant cells using a multi-gas plasma jet.

Protein introduction into cells is more difficult in plants than in mammalian cells, although it was reported that protein introduction was successful in shoot apical meristem and leaves only together with a cell-penetrating peptide. In this study, we tried to introduce superfolder green fluorescent protein (sGFP)-fused to adenylate cyclase as a reporter protein without a cell-penetrating peptide into the cells of tobacco leaves by treatment with atmospheric non-thermal plasmas. For this purpose, CO2 or N2 plasma was generated using a multi-gas plasma jet. Confocal microscopy indicated that sGFP signals were observed inside of leaf cells after treatment with CO2 or N2 plasma without substantial damage. In addition, the amount of cyclic adenosine monophosphate (cAMP) formed by the catalytic enzyme adenylate cyclase, which requires cellular calmodulin for its activity, was significantly increased in leaves treated with CO2 or N2 plasma, also indicating the introduction of sGFP-fused adenylate cyclase into the cells. These results suggested that treatment with CO2 or N2 plasma could be a useful technique for protein introduction into plant tissues.

Evolutionary clade affects resistance of Clostridium difficile spores to Cold Atmospheric Plasma

Clostridium difficile is a spore forming bacterium and the leading cause of colitis and antibiotic associated diarrhoea in the developed world. Spores produced by C. difficile are robust and can remain viable for months, leading to prolonged healthcare-associated outbreaks with high mortality. Exposure of C. difficile spores to a novel, non-thermal atmospheric pressure gas plasma was assessed. Factors affecting sporicidal efficacy, including percentage of oxygen in the helium carrier gas admixture, and the effect on spores from different strains representing the five evolutionary C. difficile clades was investigated. Strains from different clades displayed varying resistance to cold plasma. Strain R20291, representing the globally epidemic ribotype 027 type, was the most resistant. However all tested strains displayed a ~3 log reduction in viable spore counts after plasma treatment for 5 minutes. Inactivation of a ribotype 078 strain, the most prevalent clinical type seen in Northern Ireland, was further assessed with respect to surface decontamination, pH, and hydrogen peroxide concentration. Environmental factors affected plasma activity, with dry spores without the presence of organic matter being most susceptible. This study demonstrates that cold atmospheric plasma can effectively inactivate C. difficile spores, and highlights factors that can affect sporicidal activity.

Adhesive Bonding to Computer-aided Design/ Computer-aided Manufacturing Esthetic Dental Materials: An Overview.

To review the adhesive bonding to different computer-aided design/computer-aided manufacturing (CAD/CAM) esthetic restorative materials. The use of CAD/CAM esthetic restorative materials has gained popularity in recent years. Several CAD/ CAM esthetic restorative materials are commercially available. Adhesive bonding is a major determinant of success of CAD/ CAM restorations. Review result: An account of the currently available bonding strategies are discussed with their rationale in various CAD/ CAM materials. Different surface treatment methods as well as adhesion promoters can be used to achieve reliable bonding of CAD/CAM restorative materials. Selection of bonding strategy to such material is determined based on its composition. Further evidence is required to evaluate the effect of new surface treatment methods, such as nonthermal atmospheric plasma and self-etching ceramic primer on bonding to different dental ceramics. An understanding of the currently available bonding strategies to CA/CAM materials can help the clinician to select the most indicated system for each category of materials.

Mini-interfacial Fracture Toughness of a Multimode Adhesive Bonded to Plasma-treated Dentin.

To investigate the bonding efficacy of a multimode adhesive to plasma-treated and -untreated (control) dentin using a mini-interfacial fracture toughness (mini-iFT) test. Twenty human molars were used in a split-tooth design (n = 10). The adhesive Scotchbond Universal (SBU; 3M ESPE) was applied in etch-and-rinse (E&R) and self-etch (SE) modes. Mid-coronal dentin was exposed and covered with a standardized smear layer ground to 320 grit. One half of each dentin surface received 15 s of non-thermal atmospheric plasma (NTAP), while the other half was covered with a metallic barrier and kept untreated. Following the E&R mode, dentin was plasma treated immediately after phosphoric acid etching. SBU and a resin-based composite were applied to dentin following the manufacturer's instructions. Six mini-iFT specimens were prepared per tooth (1.5 x 2.0 x 16 to 18 mm), and a single notch was prepared at the adhesive-dentin interface using a 150-μm diamond blade under water cooling. Half of the mini-iFT specimens were immediately loaded until failure in a 4-point bending test, while the other half were first stored in distilled water for 6 months. After testing, the exact dimensions of the notch were measured with a measuring optical microscope, from which ΚIc was determined. Three-way ANOVA revealed higher mini-iFT for SBU applied in E&R than SE mode for both storage times, irrespective of NTAP treatment. Overall, mini-iFT did not decrease for any of the experimental groups upon 6-month aging, while plasma treatment did not show a direct beneficial effect on mini-iFT of SBU applied in either E&R or SE mode.

Characterization of an Atmospheric Air Non-thermal Plasma Device in Relation to Ozone Production

Characterization of an Atmospheric Air Non-thermal Plasma Device in Relation to Ozone Production

A New and Simple Approach for Decontamination of Food Contact Surfaces with Gliding Arc Discharge Atmospheric Non-Thermal Plasma

In this study, a gliding arc discharge (GAD) microplasma system was designed, and its decontamination effect was investigated on stainless steel (SS), silicone (Si), and polyethylene terephthalate (PET) surfaces artificially contaminated with 8.15 ± 0.28 log cfu/mL of Escherichia coli and 6.18 ± 0.21 log cfu/mL of Staphylococcus epidermidis. Each of the contaminated surfaces was treated with high purity air (79% nitrogen and 21% oxygen) or nitrogen plasmas for 1–10 min at varying rates of gas flow. Significant reductions of 3.76 ± 0.28, 3.19 ± 0.31, and 2.95 ± 0.94 log cfu/mL in S. epidermidis, and 2.72 ± 0.82, 4.43 ± 0.14, and 3.18 ± 0.96 log cfu/mL in E. coli on SS, Si, and PET surfaces, respectively, were achieved after 5 min of plasma treatment by using nitrogen as the plasma forming gas (p < 0.05). The temperature changes of each surface during plasma generation were lower than 35 °C and were not affected by the type of plasma forming gas. Additionally, morphological changes in the structure of E. coli and S. epidermidis after GAD plasma treatments were demonstrated using scanning electron microscopy (SEM).

Non-thermal atmospheric pressure dielectric barrier discharge plasma source construction and investigation on the effect of grid on wound healing application

Non-thermal atmospheric pressure plasma sources are already known as an attractive devices for therapeutic applications including wound healing. The purpose of this investigation was to construct a portable device for skin wound healing. A planar atmospheric pressure Dielectric Barrier Discharge (DBD) plasma device was constructed. The effect of using mesh grid with DBD device was investigated for uniformity treatment of skin wounds. Reactive Nitrogen and Oxygen species were observed in the optical emission spectrum. The experiments were performed in two phases, using the DBD plasma device with/without mesh grid. In each phase, the comparison was performed between the naturally healed wounds and stimulated wounds treated daily (5 days) for 30s. The reduction of wound area, morphological changes in wounds and tissue histological parameters were analysed. The wounds treated with DBD device with mesh grid were healed faster than the control wounds and the wounds treated with DBD device without mesh grid became more inflamed and they burned as well as the wound area were increased until 8th day of wounding. It is concluded that the DBD device with mesh grid has the ability of wound healing uniformly and without grid, the electrical shock imposed to the mice body prevents natural healing.

Rapid Disinfection Performance of a Touchable Pulsed SDBD Nonthermal Plasma

In this paper, an atmospheric touchable surface dielectric barrier discharge nonthermal plasma system was introduced. The typical plasma area, pulsed voltage, pulsed current, pulse frequency, and plasma power are 459 cm2, 6 kV, 5.5 A, 10 kHz and 140 W, respectively. Its disinfection performance was evaluated on agar plate, glass, and silicone hand by four bacteria including Escherichia coli, Staphylococcus aureus, Staphylococcus albus , and Pseudomonas aeruginosa . The efficiency of plasma disinfection was enhanced with increasing voltage and frequency, but had no significant difference with bacteria type. For a 10-s treatment of agar and silicone hand, the log reductions of bacteria were 2.35–2.6 and 2.85–3.26, respectively. After a 5-s treatment of glass, 3.3–3.68 log reduction of bacteria could be obtained.

Effective degradation of organic water pollutants by atmospheric non-thermal plasma torch and analysis of degradation process

The paper reports the use of atmospheric non-thermal plasma torch as a catalyst for degradation of various organic pollutants dissolved in water. A flow of He mixed with air was used to produce the dielectric barrier discharge (DBD), at the tip of the torch, using pulsed electric excitation at 12 kV. The torch, operated at a power of 750 mW/mm2, was seen to completely degrade the aqueous solutions of the pollutants namely methylene blue (MB), methyl orange (MO) and rhodamine-B (RB), at around 10−4 M concentrations, the concentration of polluants is one order higher than of routinely used heterogeneous photocatalytic reactions, within 10 min of irradiation time at room temperature. UV Visible spectra of the organic dye molecules, monitored after different intervals of plasma-irradiation, ranging between 1 and 10 min, have been used as tools to quantify their sequential degradation. Further, instead of using He, only air was used to form plasma plume and used for degradation of organic dye which follow similar trend as that of He plasma. Further, Liquid Chromatography Mass Spectroscopy (LCMS) technique has been used to understand degradation pathway of methylene blue (MB) as a representative case. Total organic carbon (TOC) measurements indicates significant decrease in its content as a function of duration of plasma exposure onto methylene blue as a representative case. Toxicity studies were carried out onto Gram negative Escherichia coli. This indicated that methylene blue, without plasma treatment, shows growth inhibition, whereas with plasma treatment no inhibition was observed.

Development of a low-cost atmospheric non-thermal plasma jet and its characteristics in air and nitrogen

This paper deals with the development of a low-cost atmospheric non-thermal plasma jet (ANPJ) which was designed and operated previously in our laboratory. The purpose of the developed design with a small size less than 4% of the previous volume is to obtain a more portable device which holds promise for various fields of applications. The discharge is operated separately with compressed air and nitrogen gas with flow rates varied within the range of 3–18 L/min. The plasma plume length and thickness are measured as a function of the gas flow rate and input voltage V input within the range of 3–18 L/min and 2–6 kV respectively. The results showed that for nitrogen gas, the maximum values of the plume length and thickness are 20 mm and 1.3 mm respectively at a flow rate of 12 L/min and V input = 6 kV. Results of electrical characterization at V input = 6 kV such as discharge voltage, discharge current, the mean consumed power and energy showed that the maximum values of these parameters are obtained at a flow rate of 12 L/min. The developed design is found to be saving up to 65.47% and 68.54% of the consumed power compared to the previous design in the case of air and N 2 respectively. The new proposed configuration for the developed ANPJ offers more suitable characteristics than the earlier designs, especially for nitrogen gas.

Impact of Nonthermal Atmospheric Plasma on the Structure of Cellulose: Access to Soluble Branched Glucans

We have investigated the effect of non-thermal atmospheric plasma (NTAP) on the structure of microcrystalline cellulose. In particular, by means of different characterization methods, we demonstrate that NTAP promotes the partial cleavage of the β-1,4 glycosidic bond of cellulose leading to the release of short-chain cellodextrins that are reassembled in situ, preferentially at the C6 position, to form branched glucans with either a glucosyl or anhydroglucosyl terminal residue. The ramification of cellulosic chain induced by NTAP yields branched glucans that are soluble in DMSO or in water, thus opening a straightforward access to processable glucans from cellulose. Importantly, the absence of solvent and catalyst considerably facilitates downstream processing as compared to (bio)catalytic processes which typically occur in diluted conditions.

Influence of processing parameters and stress adaptation on the inactivation of Listeria monocytogenes by Non-Thermal Atmospheric Plasma (NTAP)

This study evaluated the effectiveness of Non-Thermal Atmospheric Plasma (NTAP) treatments against Listeria. Firstly, the impact of gas composition and flow rate on L. monocytogenes and L. innocua (used as a surrogate) inactivation by NTAP was monitored. Secondly, the influence of stress adaptation (growth under suboptimal conditions, using a wide range of temperatures and media acidified up to pH5.5 with citric, lactic, malic or hydrochloric acid, or short-term exposure to acid, cold or thermal shocks) on L. monocytogenes NTAP resistance was assessed. Survival curves obtained were concave upward. A mathematical model based on the Weibull distribution accurately described the inactivation kinetics. Both L. monocytogenes and L. innocua showed a higher sensitivity to plasma when the treatment was performed using air than when nitrogen was used. In fact, the use of nitrogen as working gas made the plasma treatment almost ineffective. The effect of gas flow rate on the effectiveness of the NTAP treatment depended on the type of gas used to generate plasma. Increases in flow rate from 5 to 10L/min caused an acceleration of bacterial inactivation when air was used, while an additional increase of gas flow from 10 to 15L/min had a minor impact on microbial inactivation. On the other hand, gas flow rate hardly affected NTAP treatment efficiency when nitrogen was used to generate plasma. L. monocytogenes growth under sub-optimal temperature or pH conditions or short-term exposure to acid, heat or cold stress conditions did not significantly modify its NTAP resistance. This suggests that temperature and pH stress adaptation does not induce a cross-protection response against NTAP treatments in L. monocytogenes, what makes NTAP an attractive technology for food decontamination within minimal processing strategies targeting this pathogenic microorganism.

Treatment of gastric cancer cells with nonthermal atmospheric plasma generated in water.

Nonthermal atmospheric plasma (NTAP) can be applied to living tissues and cells as a novel technology for cancer therapy. The authors report on a NTAP argon solution generated in deionized (DI) water for treating human gastric cancer cells (NCI-N87). Our findings show that the plasma generated in DI water with 30-min duration has the strongest effect on apoptosis in precultured human gastric cancer cells. This result can be attributed to the presence of reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in water during treatment. Furthermore, the data show that the elevated levels of RNS may play a more significant role than ROS in the rate of cell death.

Imaging of the Staphylococcus aureus Inactivation Process Induced by a Multigas Plasma Jet.

To identify mechanisms underlying the bacterial inactivation process by atmospheric nonthermal plasma using a unique plasma jet that can generate various gas plasmas, Staphylococcus aureus were irradiated with carbon dioxide plasma, which produces a large amount of singlet oxygens, and nitrogen plasma, which produces a large amount of OH radicals. And damaged areas of plasma-treated bacteria were observed by field emission scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. As a result, bacteria were damaged by both gas plasmas, but the site of damage differed according to gas species. Therefore, it suggests that singlet oxygen generated by carbon dioxide plasma or other reactive species caused by singlet oxygen contributes to the damage of internal structures of bacteria through the cell wall and membrane, and OH radicals generated by nitrogen plasma or other reactive species derived from OH radicals contribute to damage of the cell wall and membrane.

ChemInform Abstract: Depolymerization of Cellulose to Processable Glucans by Non‐Thermal Technologies

AbstractReview: [60 refs.

Disinfection of Streptococcus mutans biofilm by a non-thermal atmospheric plasma brush

This study investigated the argon plasma treatment effect on disinfecting dental biofilm by using an atmospheric pressure plasma brush. Streptococcus mutans biofilms were developed for 3 days on the surfaces of hydroxyapatite (HA) discs, which were used to simulate human tooth enamel. After plasma treatment, cell viability in the S. mutans biofilms was characterized by using 3-(4,5-dimethylazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) assay and confocal laser scanning microscopy (CLSM). Compared with the untreated control group, about 90% bacterial reduction in the biofilms was observed after 1 min plasma treatment. Scanning electron microscopy (SEM) examination indicated severe cell damages occurred on the top surface of the plasma treated biofilms. Confocal laser scanning microscopy (CLSM) showed that plasma treatment was effective as deep as 20 µm into the biofilms. When combined with antibiotic treatment using 0.2% chlorhexidine digluconate solution, the plasma treatment became more effective and over 96% bacterial reduction was observed with 1 min plasma treatment.

Mitochondria-Mediated Anticancer Effects of Non-Thermal Atmospheric Plasma.

Non-thermal atmospheric pressure plasma has attracted great interest due to its multiple potential biomedical applications with cancer treatment being among the most urgent. To realize the clinical potential of non-thermal plasma, the exact cellular and molecular mechanisms of plasma effects must be understood. This work aimed at studying the prostate cancer specific mechanisms of non-thermal plasma effects on energy metabolism as a central regulator of cell homeostasis and proliferation. It was found that cancer cells with higher metabolic rate initially are more resistant to plasma treated phosphate-buffered saline (PBS) since the respiratory and calcium sensitive signaling systems were not responsive to plasma exposure. However, dramatic decline of cancer oxidative phosphorylation developed over time resulted in significant progression of cell lethality. The normal prostate cells with low metabolic activity immediately responded to plasma treated PBS by suppression of respiratory functions and sustained elevation of cytosolic calcium. However, over time the normal cells start recovering their mitochondria functions, proliferate and restore the cell population. We found that the non-thermal plasma induced increase in intracellular ROS is of primarily non-mitochondrial origin. The discriminate non-thermal plasma effects hold a promise for clinical cancer intervention.

Comparison of free radicals formation induced by cold atmospheric plasma, ultrasound, and ionizing radiation

Plasma medicine is increasingly recognized interdisciplinary field combining engineering, physics, biochemistry and life sciences. Plasma is classified into two categories based on the temperature applied, namely “thermal” and “non-thermal” (i.e., cold atmospheric plasma). Non-thermal or cold atmospheric plasma (CAP) is produced by applying high voltage electric field at low pressures and power. The chemical effects of cold atmospheric plasma in aqueous solution are attributed to high voltage discharge and gas flow, which is transported rapidly on the liquid surface. The argon-cold atmospheric plasma (Ar-CAP) induces efficient reactive oxygen species (ROS) in aqueous solutions without thermal decomposition. Their formation has been confirmed by electron paramagnetic resonance (EPR) spin trapping, which is reviewed here. The similarities and differences between the plasma chemistry, sonochemistry, and radiation chemistry are explained. Further, the evidence for free radical formation in the liquid phase and their role in the biological effects induced by cold atmospheric plasma, ultrasound and ionizing radiation are discussed.

Non-Thermal Atmospheric Plasma: Can it Be Taken as a Common Solution for the Surface Treatment of Dental Materials?**supported by the Department of Scientific Research, Eskisehir Osmangazi University, Turkey (No. 201441045)

This study aimed to evaluate the surface roughness and wetting properties of various dental prosthetic materials after different durations of non-thermal atmospheric plasma (NTAP) treatment. One hundred and sixty discs of titanium (Ti) (n:40), cobalt chromium (Co-Cr) (n:40), yttrium stabilized tetragonal zirconia polycrystals (Y-TZP) (n:40) and polymethylmethacrylate (PMMA) (n:40) materials were machined and smoothed with silicon carbide papers. The surface roughness was evaluated in a control group and in groups with different plasma exposure times [1-3-5 s]. The average surface roughness (Ra) and contact angle (CA) measurements were recorded via an atomic force microscope (AFM) and tensiometer, respectively. Surface changes were examined with a scanning electron microscope (SEM). Data were analyzed with two-way analysis of variance (ANOVA) and the Tukey HSD test α=0.05). According to the results, the NTAP surface treatment significantly affected the roughness and wettability properties (P < 0.05). SEM images reveal that more grooves were present in the NTAP groups. With an increase in the NTAP application time, an apparent increment was observed for Ra, except in the PMMA group, and a remarkable reduction in CA was observed in all groups. It is concluded that the NTAP technology could enhance the roughening and wetting performance of various dental materials.