Non-road Engine Research Articles

Unignorable Emissions and Potential Health Effects of Unregulated Pollutants from Nonroad Engines Using Greener Fuels — A Review

Unignorable Emissions and Potential Health Effects of Unregulated Pollutants from Nonroad Engines Using Greener Fuels — A Review

Assessment of Carbon-Dioxide Emission from Non-Road Equipment Construction Sources at a Flyover Development Site in Port Harcourt, Nigeria

It is emphasized that global warming and climate change vary directly with the increase in the concentration of greenhouse gases, particularly carbon dioxide across domains. The constructions of social and economic infrastructures in developing counties such as Nigeria at a higher rate increases the emissions of carbon dioxide (CO2) into the lower atmosphere. Non-road construction equipment sources powered by fossil fuels are considered to be primary emitters of greenhouse gases during the construction stages of large infrastructure project. In this study, inventory of non-road construction machinery emissions from the Tank junction flyover construction site along East-West Road in Port Harcourt metropolis were estimated via field data gathering. Results showed that an average of about 398.7 g/s (4134.4 ton/year) of CO2 is released from the construction site in Port Harcourt, Nigeria. Among the various types of non-road engines considered, the mobile crane was the largest single contributor to the total CO2 emissions, accounting for 18.5%. Machinery with power above 300 kW were 8 out of 30 equipment on site and accounted for the largest share (52.87%) of total CO2 emissions. Based on the findings from current research literature and the case study, control strategies such as enforcing standards and policy, conducting impact assessment, adopting low carbon technology, and restricting energy utilization need to be implemented in other reduce the impact of global warming and alleviate climate change. Therefore, CO2 emission mitigation plans and schemes are necessary alongside standardized frameworks and guidelines. All stakeholders must play their roles efficiently to reduce CO2 emissions and aid in mitigating the effects of climate change.

FTIR Analysis for Determining Stability of Methanol-HVO Blends for Non-Road Engine Application

FTIR Analysis for Determining Stability of Methanol-HVO Blends for Non-Road Engine Application

Reactive organic carbon air emissions from mobile sources in the United States.

Mobile sources are responsible for a substantial controllable portion of the reactive organic carbon (ROC) emitted to the atmosphere, especially in urban environments of the United States. We update existing methods for calculating mobile source organic particle and vapor emissions in the United States with over a decade of laboratory data that parameterize the volatility and organic aerosol (OA) potential of emissions from on-road vehicles, nonroad engines, aircraft, marine vessels, and locomotives. We find that existing emission factor information from Teflon filters combined with quartz filters collapses into simple relationships and can be used to reconstruct the complete volatility distribution of ROC emissions. This new approach consists of source-specific filter artifact corrections and state-of-the-science speciation including explicit intermediate-volatility organic compounds (IVOCs), yielding the first bottom-up volatility-resolved inventory of US mobile source emissions. Using the Community Multiscale Air Quality model, we estimate mobile sources account for 20 %-25 % of the IVOC concentrations and 4.4 %-21.4 % of ambient OA. The updated emissions and air quality model reduce biases in predicting fine-particle organic carbon in winter, spring, and autumn throughout the United States (4.3 %-11.3 % reduction in normalized bias). We identify key uncertain parameters that align with current state-of-the-art research measurement challenges.

Effect of diesel injection pressure for enhancing combustion and reducing mechanical vibration and noise emissions in a non-road diesel engine

In this study, the combustion, performance, emissions, noise, and vibration characteristics of a single-cylinder, four-stroke, air-cooled diesel engine used for non-road purposes were investigated by controlling different injection pressures with a common rail fuel injection system. The aim of this study is to enhance the combustion performance and improve the existing noise and vibration levels of this commonly used non-road diesel engine in fields such as agriculture, wetlands, and the construction sector by optimizing the injection pressure. The experiments were conducted under low and medium load conditions and at a constant engine speed. The single-cylinder, non-road engine's fuel injection system was controlled using a common rail fuel delivery system, and four different diesel injection pressures (250, 300, 350, and 400 bar) were utilized. The experimental results have shown that the combustion performance, emissions, noise, and vibration values of the non-road diesel engine improved with an increase in diesel injection pressure (DIP). Increasing DIP led to higher maximum combustion pressures and resulted in reductions of HC, CO, and smoke emissions by up to 25%, 48%, and 59%, respectively. Vibration values also decreased by up to 25%.

Effects of piston shape and nozzle specifications on part-load operation of natural gas–diesel dual-fuel RCCI engine and its application to high load extension

• Effects of piston shape and multi-angle nozzle were evaluated for DF RCCI operation. • Enhanced air utilization w/multi-angle nozzle reduced combustion and HT losses. • The highest GIE of RCCI improved as 51.8 % by hardware modifications. • Intake air amount could be increased by lowering CR (from 17 to 15) at the maximum load. • The maximum load of RCCI could be extended from 81 (reference) to 101 kW of BP. In this study, the effects of modifications of both the piston shape and injector nozzle are experimentally investigated for high load extension of a natural gas–diesel dual-fuel reactivity-controlled compression ignition (RCCI) engine. First, a bathtub shape with a reduced compression ratio is applied to the modified piston which was reported to improve the flame propagation in squish volume, the cooling loss, and the air induction rate under the same limit of in-cylinder pressure from previous studies. In addition, a multiangle two-layer injector is used to extend the maximum load, which has been proven to be effective for unburned hydrocarbon emissions and gross indicated efficiency in part-load operation in our previous study. The experiments are conducted under both 1200 rpm part-load operation (approximately 1950 J/cylinder per cycle of fuel input energy) and 1800 rpm maximum load operation. The objectives are to comprehensively evaluate the effects of the modifications on natural gas–diesel RCCI operation and verify the effects of all load conditions. The experimental results reveal that the changes in the piston—reduction in the compression ratio and a bathtub piston shape—are effective for both NOx and smoke emissions as the diesel injection timing is advanced. Although the multi-hole double layer (combined narrow and wide injection) has less effect on emissions compared to that of the change in piston, it affects the mixing process inside the cylinder, thus retarding the combustion phasing, prolonging the combustion duration, and eventually reducing the cooling loss. Both modifications are highly effective for advanced diesel injection timing corresponding to RCCI operation, which extends high-load operation from 80.9 to 101 kW of brake power, relatively 24.8 % increase, by adopting both the piston and injector modifications. Based on the modifications, the mass fraction of natural gas is suggested to be approximately 80 %. A higher fraction causes the variation in the maximum in-cylinder pressure to be extremely sensitive to allow robust operation. In contrast, if it is lower, the amounts of both NOx and smoke emissions exceed the emission standard levels (0.4 g/kWh and 15 mg/kWh for NOx and smoke emissions, respectively, corresponding to Stage-V of non-road engine operation).

Nucleation-accumulation mode trade-off in non-volatile particle emissions from a small non-road small diesel engine.

Small (< 8kW) non-road engines are a significant source of pollutants such as particle number (PN) emissions. Many small non-road engines do not have diesel particulate filters (DPFs). They are so designed that air-fuel ratio (AFR) can be adjusted to control visible diesel smoke and particulate matter (PM) resulting from larger accumulation mode particles. However, the effect of AFR variation on smaller nucleation mode nanoparticle emissions is not well understood. Several studies on larger engines have reported a trade-off between smaller and larger particles. In this study, AFR was independently varied over the entire engine map of a naturally aspirated (NA) non-road small diesel engine using forced induction (FI) of externally compressed air. AFR's ranged from 57 to 239 compared to the design range of 23-92 for the engine, including unusually high AFR's at full-load operation, not previously reported for conventional combustion. As expected, larger accumulation mode particles were lowered (up to 15 times) for FI operation. However, the smaller nucleation mode nanoparticles increased up to 15 times. Accumulation mode particles stopped decreasing above an AFR threshold while nucleation particles continuously increased. In-cylinder combustion analysis showed a slightly smaller ignition delay and higher burn rate for FI cases relative to NA operation. Much higher peak cylinder pressures were accompanied by much lower combustion and exhaust gas temperatures (EGT), due to higher in-cylinder mass during FI operation. Peak nucleation mode emissions were shown to be negatively correlated to EGT for all the data, collapsing on a single curve. This is consistent with some other studies reporting increased nucleation mode emissions (and higher accumulation mode particles) with decreased load, lower speed, lower EGR, advanced combustion phasing, and higher injection pressure, all of which reduce EGT. The nucleation-accumulation trade-off has been explained by the 'adsorption hypothesis' by some investigators. In the current work, an alternative/supplemental argument has been made for the possibility that lower cylinder temperatures during the late-burning phase (correlated to lower EGT) phase hampers oxidation of nucleation mode particles and increases nucleation mode emissions.

Characterizing Real-World Particle-Bound Polycyclic Aromatic Hydrocarbon Emissions from Diesel-Fueled Construction Machines

This study employed an onboard emission measurement system to measure the real-world emission factors of particulate matter (PM), particle-bound polycyclic aromatic hydrocarbons (PAHs), and gaseous air pollutants for different types of diesel-fueled non-road construction machines operated inside confined spaces within a brick manufacturing factory located in Taiwan. To the best knowledge of the authors, this is the first study that reports real-world PM, PAH, and gaseous pollutant emission factors for non-road engines in Taiwan. The mean real-world fuel-specific emission factors of PM, carbon monoxide, total hydrocarbons, and nitric oxide were 0.712–1.17, 8.27–17.9, 3.04–5.77, and 38.1–96.8 g/kg-fuel, respectively, for the test machines. Likewise, mean ΣPAHs emission factors ranged from 157 to 230 μg/kg-fuel for three types of test machines. Further, the average emission of particle-bound PAH per unit PM emission ranged from 213 to 384 μg-PAH/g-PM. Among the analyzed PAHs, the medium-molecular weight (3- and 4-ring) compounds contributed to the largest share of particle-bound PAH emissions. However, in terms of Benzo[a]pyrene equivalent (BaPeq) toxicity, the high-molecular weight (5- and 6-ring) PAHs were more important, as they had the highest BaPeq toxic emission factors. This study provides detailed composition and emission factors of particle-bound PAHs in non-road diesel construction machine emissions, which may be useful as a chemical fingerprint for source apportionment studies.

A comparative investigation between particle oxidation catalyst (POC) and diesel particulate filter (DPF) coupling aftertreatment system on emission reduction of a non-road diesel engine

Non-road emission regulations are becoming increasingly rigorous, which makes it necessary for non-road engines to adopt aftertreatment systems. The commonly used aftertreatments mainly include diesel oxidation catalytic (DOC), diesel particulate filter (DPF), particle oxidation catalyst (POC), selective catalytic reduction (SCR) and ammonia purification catalyst (ASC). The purpose of this study is to investigate the effects of using an integrated system (DOC + DPF/POC + SCR + ASC) on non-road diesel engine emissions under steady-state and transient operating conditions, respectively. The major works are the comparison between POC and DPF from the viewpoint of emission reduction. The results show that both POC and DPF can effectively reduce particulate matter (PM) and nitrogen oxide (NOX) emissions under steady-state conditions, and DPF has better purification effect than POC, especially for PM. The PM conversion rate of DPF is up to 87%, while that of POC is only 60% under the non-road steady-state test cycle (NRSC). Both NOX and hydrocarbon (HC) conversion rates are high, exceeding 95%. The conversions of PM, NOX, HC, and carbon monoxide (CO) of DPF in the non-road transient test cycle (NRTC) are 92.83%, 96.99%, 96.86% and 81.45%, respectively, while those of POC are 60.12%, 95.45%, 92.82% and 79.51%, respectively. Both the POC and DPF systems can meet the emission regulation limits. As a result, POC has the potential to substitute DPF in non-road engines due to its lower product and maintenance costs. We hope that the comparison study will provide useful guidance for improving the emissions performance of non-road diesel engines.

Methodology of diesel particulate filter testing on test bed for non-road engine application

This paper describes the methodology and test results of diesel particulate filter (DPF) functional testing performed on non-road compression ignition engine installed on test bed. The scope of work included testing of various DPF regeneration strategies, backpressure and balance point tests and emission performance evaluation during a legislative test cycles. The aim of this study was to observe and investigate the influence of exhaust gas parameters on DPF functionality in terms of soot loading, type and duration of the regeneration and emission performance. Under investigation was also the capability of soot burning rate. The DPF sample under test was part of the complete exhaust aftertreatment system (ATS) which consisted of: a diesel oxidation catalyst (DOC), a DPF and a selective catalytic reduction system (SCR). Testing was carried out on a heavy-duty diesel engine installed on a test stand with a dynamic dynamometer and equipped with an emission bench. The test program allowed to assess the engine matching to exhaust aftertreatment system with regard to emissions compliance, in-service operation and necessary engine control unit (ECU) calibration works. The results show the influence of the DPF regeneration strategy on its duration and on the soot mass burn rate. Passive DPF regeneration was a favorable mode of DPF cleaning, due to lack of fuel penalty and lower aging impact on the entire ATS. Optimization of soot flow rate, exhaust gas temperature and the chemistry of the DOC/DPF was further recommended to ensure the long-term durability of the entire system.

Numerical Study on the Performance and NOx Emission Characteristics of an 800cc MPI Turbocharged SI Engine

The main purpose of this study is to optimize engine performance and emission characteristics of off-road engines with retarded spark timing compared to MBT by repurposing the existing passenger engine. This study uses a one-dimensional (1D)-simulation to develop a non-road gasoline MPI turbo engine. The SI turbulent flame model of the GT-suite, an operational performance predictable program, presents turbocharger matching and optimal operation design points. To optimize the engine performance, the SI turbulent model uses three operation parameters: spark timing, intake valve overlap, and boost pressure. Spark timing determines the initial state of combustion and thermal efficiency, and is the main variable of the engine. The maximum brake torque (MBT) point can be identified for spark timing, and abnormal combustion phenomena, such as knocking, can be identified. Spark timing is related to engine performance, and emissions of exhaust pollutants are predictable. If the spark timing is set to variables, the engine performance and emissions can be confirmed and predicted. The intake valve overlap can predict the performance and exhaust gas by controlling the airflow and combustion chamber flow, and can control the performance of the engine by controlling the flow in the cylinder. In addition, a criterion can be set to consider the optimum operating point of the non-road vehicle while investigating the performance and exhaust gas emissions accompanying changes in boost pressure With these parameters, the design of experiment (DoE) of the 1D-simulation is performed, and the driving performance and knocking phenomenon for each RPM are predicted during the wide open throttle (WOT) of the gasoline MPI Turbo SI engine. The multi-objective Pareto technique is also used to optimize engine performance and exhaust gas emissions, and to present optimized design points for the target engine, the downsized gasoline MPI Turbo SI engine. The results of the Pareto optimal solution showed a maximum torque increase of 12.78% and a NOx decrease of 54.31%.

Technologies used in agricultural machinery engines that contribute to the reduction of atmospheric emissions: A patent analysis in Brazil

Greenhouse gas emissions are directly associated with climate change issues. Part of the emissions originates from the burning of fossil fuels such as coal, natural gas, and oil used as an energy source for the performance of agricultural machinery's internal combustion engines. However, discussions relevant to the topic are under development in Brazil, and there is a lack of research in the academic field on the intellectual property of agricultural technologies. The purpose of the article is to analyze patent filings in Brazil on technologies that seek to mitigate pollutant emissions from agricultural machinery engines. As a complement, a survey is carried out on the profile of manufacturers in the Brazilian market for technologies for agricultural machinery engines and countries that stand out to develop technologies related to reducing pollutant emissions. The Questel Orbit Platform was used to collect patent data between 2006 and 2017. The research represents innovation and extension of pollutant emissions by non-road engines and patent analysis, a field of research considered in continuous evolution by different researchers and under construction.

A Technique of Estimating Particulate Matter Emission in Non-Road Engine Transient Cycle

A Technique of Estimating Particulate Matter Emission in Non-Road Engine Transient Cycle

Combustion Studies of a Non-Road Diesel Engine with Several Alternative Liquid Fuels

Sustainable liquid fuels will be needed for decades to fulfil the world’s growing energy demands. Combustion systems must be able to operate with a variety of renewable and sustainable fuels. This study focused on how the use of various alternative fuels affects combustion, especially in-cylinder combustion. The study investigated light fuel oil (LFO) and six alternative liquid fuels in a high-speed, compression-ignition (CI) engine to understand their combustion properties. The fuels were LFO (baseline), marine gas oil (MGO), kerosene, rapeseed methyl ester (RME), renewable diesel (HVO), renewable wood-based naphtha and its blend with LFO. The heat release rate (HRR), mass fraction burned (MFB) and combustion duration (CD) were determined at an intermediate speed at three loads. The combustion parameters seemed to be very similar with all studied fuels. The HRR curve was slightly delayed with RME at the highest load. The combustion duration of neat naphtha decreased compared to LFO as the engine load was reduced. The MFB values of 50% and 90% occurred earlier with neat renewable naphtha than with other fuels. It was concluded that with the exception of renewable naphtha, all investigated alternative fuels can be used in the non-road engine without modifications.

Experimental investigation of iso-butanol/diesel reactivity controlled compression ignition combustion in a non-road diesel engine

As non-road engine emission control programs are developed largely in number of countries around the world, adopting a high efficiency and low emission combustion techniques has become essential. Flexible fuel operation using in-cylinder blending technique is a primary option for using higher octane fuel in a non-road diesel engine to mitigate emissions and fossil fuel dependency. In the present study, iso-butanol/diesel dual fuel reactivity controlled compression ignition concept is preferred considering the benefits of iso-butanol over other alcohol fuels and better combustion control over other low temperature combustion concepts. An experimental investigation is performed on a suitably modified single cylinder non-road diesel engine for the entire load range (0–100% engine full load) focusing on the effect of operating parameters (iso-butanol mass fraction, diesel injection timing, diesel injection pressure, diesel mass in split injection, and intake air temperature) on the dual fuel combustion, performance and emission characteristics. The reactivity controlled compression ignition combustion is analyzed at each load condition and the best operating points are selected based on brake thermal efficiency and emissions. The results indicated that increase in iso-butanol mass fraction with advanced start of injection of direct injected diesel fuel showed a 99% reduction in oxides of nitrogen and a 91% reduction in smoke emissions with 4.5% increase in brake thermal efficiency. Further the drawback in dual fuel combustion, hydrocarbon emission is reduced by 65% with an increase of intake air temperature from 303 K to 338 K. Also, both hydrocarbon and carbon monoxide emissions are reduced with increase in diesel injection pressure and mass of diesel fuel injected in first injection due to the enhanced mixture formation.

Effects of insulation on exhaust temperature and subsequent SCR efficiency of a heavy-duty diesel engine

Ammonia/urea selective catalytic reduction (SCR) is an efficient technology to control NOx emission from diesel engines. One of the critical challenges of SCR systems is its lack of catalytic activities in low temperature conditions such as cold start or warm-up periods. In this study, the effect of pipe insulation on the reduction of exhaust temperature drop was experimentally investigated based on dynamometer tests with a heavy-duty non-road diesel engine. The temperature drop of exhaust gas was measured with and without applying pipe insulation. Measurement results revealed that the effect of insulation on the mitigation of temperature loss becomes significant as engine brake power decreases. Thus, it is expected that the need for pipe insulation would be increased to keep SCR deNOx efficiency high, especially at low temperature conditions. Also, this study carried out numerical simulations to quantify the impact of pipe insulation on NOx conversion efficiency of a commercial SCR catalyst over a scheduled non-road transient cycle (NRTC) mode. Under the current heavy-duty non-road engine and SCR conditions, the application of pipe insulation would reduce 19.5 % of total cumulative tail-out NOx emission over NRTC hot mode. These results led to the cycle-averaged SCR efficiency of 98.2 % for ‘with insulation’, while it was predicted to be lowered to 97.6 % for ‘without insulation’.

Characterization and comparison of oxidative potential of real-world biodiesel and petroleum diesel particulate matter emitted from a nonroad heavy duty diesel engine

Little is known regarding the oxidative potential of biodiesel particulate matter (PM) relative to diesel PM emitted from heavy duty diesel (HDD) nonroad engines generated in real-world occupational settings. The composition of biodiesel and diesel PM can include transition metals, polar, and nonpolar organic species which can increase oxidative potential via production of reactive oxygen species (ROS). Elevated ROS can lead to oxidative stress and induce antioxidant defense, inflammation, and toxicity. This study characterized the chemical composition of PM (water soluble organic carbon and elemental metals) collected in a real-world occupational setting. ROS production in a human epithelial cell line (BEAS-2B) treated with biodiesel and diesel PM extracts was compared to oxidative potential measured by an acellular dithiothreitol (DTT) assay. The oxidative potential (DTT consumption rate) of diesel PM was 21% greater than biodiesel PM at the highest treatment concentration (60 μg/mL), yet the ROS generated in vitro were similar between fuel types. Average concentrations of Cu, Cr and Zn were higher in diesel PM compared to biodiesel PM. Additionally, there was a significant correlation between DTT consumption and Cu in diesel PM (r = 0.98), but not B20 PM. There was a strong correlation between WSOC content in diesel PM and ROS generated in vitro (r = 0.83), but no correlation between WSOC content in biodiesel PM and ROS. Taken together, the results indicate the influence of fuel type on the chemical composition and oxidative potential of PM generated by a nonroad HDD engine operated at a recycling center. While acknowledging the potential influence of other species of interest not measured (i.e., quinones), real-world petroleum diesel PM emissions had higher oxidative potential compared to biodiesel PM suggesting that biodiesel use may reduce risk to human health.

Gas-phase and semivolatile organic emissions from a modern nonroad diesel engine equipped with advanced aftertreatment

ABSTRACTU.S. Tier 4 Final and Euro Stage IV and V regulations for nonroad compression-ignition engines have led to the development of exhaust aftertreatment technologies optimized for nonroad engines and duty cycles. In this study, several aftertreatment configurations consisting of state-of-the-art diesel oxidation catalysts (DOCs), diesel particulate filters (DPFs), copper (Cu) zeolite– and vanadium-based selective catalytic reduction (SCR) catalysts, and ammonia oxidation (AMOX) catalysts are evaluated using both nonroad transient (NRTC) and steady (8-mode NRSC) cycles in order to understand both component- and system-level effects of diesel aftertreatment on gas-phase, semivolatile, and particle-phase and particle-bound unregulated organic emissions. Organic emissions reported in this work include total hydrocarbon (THC), n-alkanes, branched alkanes, saturated cycloalkanes, aromatics, aldehydes, ketones, hopanes, steranes, and soluble organic fraction (SOF). Brake-specific emissions are reported for four configurations, including engine-out, DOC+CuZ-SCR+AMOX, V-SCR+AMOX, and DOC+DPF+CuZ-SCR+AMOX, and conversion of engine-out emissions is reported for the three aftertreatment configurations. Mechanisms responsible for the reduction of organic species are discussed in detail. This summary of emissions from a current nonroad diesel engine equipped with advanced aftertreatment can be used to more accurately model the impact of anthropogenic emissions on the atmosphere with tools such as the U.S. Environmental Protection Agency’s Motor Vehicle Emissions Simulator (MOVES2014a) model.Implications: Anthropogenic emissions are a source of significant human health and environmental risk. This study, focused on the treatment of exhaust emissions from a modern nonroad diesel engine with a variety of aftertreatment configurations, examines the impact that human industrial activity can have on air pollution. In particular, we focus on the remediation of gas-phase and semivolatile organic emissions by emission reduction technologies. This detailed summary of emissions from a current nonroad diesel engine equipped with advanced aftertreatment can be used to more accurately model the impact of anthropogenic emissions on the atmosphere with tools such as the U.S. Environmental Protection Agency’s MOVES2014a model.

Monetized health benefits attributable to mobile source emission reductions across the United States in 2025

By-products of mobile source combustion processes, such as those associated with gasoline- and diesel-powered engines, include direct emissions of particulate matter as well as precursors to particulate matter and ground-level ozone. Human exposure to fine particulate matter with an aerodynamic diameter smaller than 2.5 μm (PM2.5) is associated with increased incidence of premature mortality and morbidity outcomes. This study builds upon recent, detailed source-apportionment air quality modeling to project the health-related benefits of reducing PM2.5 from mobile sources across the contiguous U.S. in 2025. Updating a previously published benefits analysis approach, we develop national-level benefit per ton estimates for directly emitted PM2.5, SO2/pSO4, and NOX for 16 mobile source sectors spanning onroad vehicles, nonroad engines and equipment, trains, marine vessels, and aircraft. These benefit per ton estimates provide a reduced-form tool for estimating and comparing benefits across multiple mobile source emission scenarios and can be applied to assess the benefits of mobile source policies designed to improve air quality. We found the benefit per ton of directly emitted PM2.5 in 2025 ranges from $110,000 for nonroad agriculture sources to $700,000 for onroad light duty gas cars and motorcycles (in 2015 dollars and based on an estimate of PM-related mortality derived from the American Cancer Society cohort study). Benefit per ton values for SO2/pSO4 range from $52,000 for aircraft sources (including emissions from ground support vehicles) to $300,000 for onroad light duty diesel emissions. Benefit per ton values for NOX range from $2100 for C1 and C2 marine vessels to $7500 for “nonroad all other” mobile sources, including industrial, logging, and oil field sources. Benefit per ton estimates increase approximately 2.26-fold when using an alternative concentration response function to derive PM2.5-related mortality. We also report benefit per ton values for the eastern and western U.S. to account for broad spatial heterogeneity patterns in emissions reductions, population exposure and air quality benefits.

Effect of anhydrous ethanol/gasoline blends on performance and exhaust emissions of spark-ignited non-road engines.

Ethanol is a renewable fuel and it is considered an alternative to gasoline in Otto-cycle engines. The present study evaluated the behavior of exhaustion gas carbon monoxide (CO) and total hydrocarbons (THC) according to the levels of anhydrous ethyl alcohol (AEA) added to gasoline in different proportions (E0, E10, E20, E27, that is, pure gasoline and its blends with AEA at 10, 20, and 27% v/v) in the use of non-road single cylinder engines of different powers (13 and 6.5hp), to the loads applied to engine-generators and the air-fuel ratio (A/F) admitted to the engine cylinders. Also, the performance of engine-generators was verified in terms of mass, specific and energetic consumption and efficiency of the evaluated systems for the same blends and loads. The results showed that an increase in the AEA content in the blend resulted in significant drops in CO and THC concentrations for both engine-generators, while fuel consumption showed a slight upward trend; the increases in applied loads resulted in an increase in CO and THC concentrations and fuel consumption. In general, a higher AEA content (oxygenated) in the blends had a greater effect on gaseous emissions compared to the effect on consumption and system efficiency.