Non-road Engine Research Articles

Waste Cooking Oil Biodiesel Use in Two Off-Road Diesel Engines

This study examines the composition and combustion performance of biodiesel produced from waste cooking oil. Six fuel batches produced from waste oil used in dining-hall fryers were examined to determine their physical and chemical properties, including their elemental and fatty acid methyl ester composition. Oleic and linoleic methyl esters accounted for more than 70% of the fuel composition, while the oxygen content averaged 10.2% by weight. Exhaust emissions were monitored for 5–100% biodiesel blends using two off-road engines: a 2007 Yanmar diesel generator and a 1993 John Deere front mower. Increasing biodiesel content resulted in reduced emissions of partial combustion products from the diesel generator but a rise in NOx, with the greatest changes occurring between 5 and 20% biodiesel content. For the riding mower, biodiesel content up to 50% had little effect on emissions, while NOx and total hydrocarbon emissions decreased with 100% biodiesel. The difference in NOx emissions is attributed to the two different fuel injection control designs used in the two engines. These results indicate that the effects of biodiesel use on nonroad engine exhaust emissions may be substantially lower in older engines optimized for performance over emissions control.

Particle Number Emissions of Nonroad Diesel Engines of Various Ages

Over the last two decades, gaseous and particle mass emissions of new diesel engines have been reduced effectively and progressively in response to the emissions legislation and due to the applied new technologies. There is, however, increasing concern about whether the engine modifications, while improving combustion and reducing emissions, have increased the number emissions of ultrafine and nanoparticles. So far, emissions regulations have solely been based on particulate matter (PM) mass measurements, not on particle number. Nanoparticles, however, form a major part of the PM emissions, but they do not considerably contribute to the PM mass and cannot be seen as a problem, if only PM mass is determined. Therefore, there is increasing interest in expanding the scope of the regulations to also include particle number emissions, e.g., Euro VI for on-road engines. The PM number limit will also be enforced for nonroad engines slightly later. Thus, more information is required about the particle number emissions themselves, but also about the effects of the engine technology on them. Wall-flow diesel particulate filters reduce the particle number very effectively within the entire particle size range. Nevertheless, in order to keep the filter as small as possible and to lessen the need for regeneration, the engine-out PM number should also be minimized. If the diesel particulate filters (DPFs) could be left out or replaced by a simpler filter, there would be greater freedom of space utilization or cost savings in many nonroad applications. This might be realized in installations where the engine is tuned at high raw NOx and a selective catalytic reduction (SCR) system is adopted for NOx reduction. However, it is not self-evident that new engine technologies would reduce the PM number emissions sufficiently. In this study, particle number emissions were analyzed in several nonroad diesel engines, representing different engine generations and exploiting different emissions reduction technologies: four- or two-valve heads, exhaust gas recirculation, different injection pressures and strategies, etc. All engines were turbocharged, intercooled, direct-injection nonroad diesel engines. Most engines used common-rail fuel injection technology. Comparisons were, however, also performed with engines utilizing either a distributor-type or an in-line fuel injection pump to see the long-term development of the particle number emissions. In this paper, the PM number emissions of nine nonroad diesel engines are presented and compared. Gaseous exhaust emissions and fuel consumption figures are also provided.

Uralsky Farfor will clear air

Biodiesel is regarded by many as a “greener” alternative fuel to petroleum diesel with potentially lower health risk. However, recent studies examining biodiesel particulate matter (PM) characteristics and health effects are contradictive, and typically utilize PM generated by passenger car engines in laboratory settings. There is a critical need to analyze diesel and biodiesel PM generated in a “real-world” setting where heavy duty-diesel (HDD) engines and commercially purchased fuel are utilized. This study compares the mass concentrations, chemical composition and cytotoxicity of real-world PM from combustion of both petroleum diesel and a waste grease 20% biodiesel blend (B20) at a community recycling center operating HDD nonroad equipment. PM was analyzed for metals, elemental/organic carbon (EC/OC), polycyclic aromatic hydrocarbons (PAHs), and nitro-polycyclic aromatic hydrocarbons (N-PAHs). Cytotoxicity in a human lung epithelial cell line (BEAS-2B) following 24 h exposure to the real-world particles was also evaluated. On average, higher concentrations for both EC and OC were measured in diesel PM. B20 PM contained significantly higher levels of Cu and Mo whereas diesel PM contained significantly higher concentrations of Pb. Principal component analysis determined Mo, Cu, and Ni were the metals with the greatest loading factor, suggesting a unique pattern related to the B20 fuel source. Total PAH concentration during diesel fuel use was 1.9 times higher than during B20 operations; however, total N-PAH concentration was 3.3 times higher during B20 use. Diesel PM cytotoxicity was 8.5 times higher than B20 PM (p < 0.05) in a BEAS-2B cell line. This study contributes novel data on real-world, nonroad engine sources of metals, PAH and N-PAH species, comparing tailpipe PM vs. PM collected inside the equipment cabin. Results suggest PM generated from burning petroleum diesel in nonroad engines may be more harmful to human health, but the links between exposure, composition and toxicity are not straightforward.

The composition and sources of PM 2.5 organic aerosol in two urban areas of Chile

Fine particle (PM 2.5) samples were collected, using a charcoal diffusion denuder, in two urban areas of Chile, Santiago and Temuco, during the winter and spring season of 1998. Molecular markers of the organic aerosol were determined using GC/MS. Diagnostic ratios and molecular tracers were used to investigate the origin of carbonaceous aerosols. As main sources, road and non-road engine emissions in Santiago, and wood burning in Temuco were identified. Cluster analysis was used to compare the chemical characteristics of carbonaceous aerosols between the two urban environments. Distinct differences between Santiago and Temuco samples were observed. High concentrations of isoprenoid (30–69 ng m −3) and unresolved complex mixture (UCM) of hydrocarbons (839–1369 ng m −3) were found in Santiago. High concentrations of polynuclear aromatic hydrocarbons (751±304 ng m −3) and their oxygenated derivatives (4±2 ng m −3), and of n-alk-1-enes (16±13 ng m −3) were observed in Temuco.