Near-ambient Pressure X-ray Photoelectron Spectroscopy Research Articles

Dynamic Structural Evolution of CeO2 in CuO−CeO2 Catalyst Revealed by In Situ Spectroscopy

AbstractThe oxides and active metals at the interface synergistically activate reactants and thus promote the reaction, but the interface structure often changes dynamically during the reaction. In the conventional supported catalysts, the metals at the interface have been extensively studied, while the structural evolution of oxides is often overlooked due to the interference of the bulk phase signal. In this work, CeO2−CuO inverse catalysts are designed to reveal the dynamic structure evolution of CeO2 in the CeO2−CuO system during the water gas shift (WGS) reaction by in situ Raman, in situ XRD, quasi in situ XPS, and near ambient pressure XPS (NAP‐XPS). CeO2 is partially concealed in the CuO phase in the un‐pretreated catalyst and gradually exposed to the surface, forming an inverse CeOx/Cu structure during the reducing process. This structure exhibits a high catalytic activity in the WGS reaction and remains durable under the reductive conditions. When the inverse CeOx/Cu structure is exposed to the non‐redox conditions, the reconfiguration of the reduced oxide is observed which is caused by the oxygen migration of CeO2. This work explores the structure evolution of CeO2 in CeO2−CuO inverse catalyst under different conditions by in situ characterization technique and provides a reference for monitoring the dynamic changes of oxide structure.

(Keynote) Interplay between Physicochemical Properties of Precursors and “Core-Shell” Hierarchical Carbon Nitride Electrocatalysts for the Oxygen Reduction Reaction

The oxygen reduction reaction (ORR) is a major bottleneck in the operation of proton-exchange membrane fuel cells (PEMFCs) since it introduces large overpotentials (no less than 250-300 mV), which degrade significantly the energy conversion efficiency of the device. In addition, the electrocatalysts (ECs) yielding the lowest ORR overpotentials in the acidic environment found at the PEMFC cathode are based on Pt, a very scarce critical raw material (CRM). Pt raises concerns as it might trigger serious supply bottlenecks in the event of a practical widespread implementation of PEMFCs in the framework of today’s energy transition. Hence, the development of high-performing and durable ECs for the ORR is a major stepping stone towards the large-scale rollout of PEMFCs.In our research group a new breakthrough approach has been devised for the synthesis of ORR ECs, that is completely different form the preparation routes that are commonly adopted in the state of the art [1, 2]. Briefly, the approach consists in the pyrolysis and subsequent treatment of a precursor obtained by coupling suitable carbon species/sacrificial supports with a zeolitic inorganic-organic polymer electrolyte (Z-IOPE). The latter comprises anionic complexes including the Pt “catalyst” and other “co-catalysts”, which are bridged by organic binders [1,2].On one hand, the proposed approach has already shown its potential to yield ECs exhibiting a performance and durability improved with respect to Pt/C benchmark ECs. On the other hand, the proposed approach is extremely flexible, especially with respect to the synthesis of the initial EC precursor. In principle, it is possible to modulate a number of crucial features of such EC precursor, with a particular reference to: (i) the chemical composition (e.g., in terms of Pt, other “co-catalysts” and N; the latter plays a crucial role to stabilize the active sites into “coordination nests” on the EC surface, raising durability); and (ii) the morphology, that can be “templated” on suitable species (e.g., carbon species, sacrificial supports). The very flexibility of the proposed synthetic process needs to be leveraged appropriately to maximize the performance of the final ORR ECs, at the same time minimizing the efforts wasted on approaches with a low development potential.Herein it is elucidated how the modulation in the parameters involved in the synthesis of the EC precursor (e.g., the binder and the approaches to couple the Z-IOPE with the support) impact the physicochemical and electrochemical properties of the final ECs, with a particular reference to the chemical composition, morphology and distribution of the ORR active sites. An extensive characterization of the final ECs is carried out. Inductively-coupled plasma atomic emission spectroscopy (ICP-AES) and microanalysis are adopted to determine the bulk chemical composition. Near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) is used to elucidate the surface chemical composition and the chemical states of the surface elements. Ultra-high resolution scanning electron microscopy (UHR-SEM) and transmission electron microscopy (TEM) allow for the elucidation of EC morphology. The porosimetric features are probed by automatic gas adsorption instrumentations. Wide-angle X-ray diffraction (WAXD) is crucial to resolve the crystal structure. Cyclic voltammetry with the rotating ring-disk electrode method (CV-TF-RRDE) is used to clarify the “ex-situ” electrochemical performance and ORR reaction mechanism. Finally, the most promising ECs are used in the fabrication of single PEMFCs, that are tested as a function of the operating conditions.It is revealed that, in comparison with the Pt/C benchamark, some ECs are characterized by a much higher intrinsic kinetic performance due to the electronic and bifunctional effects bestowed by the carbon nitride support and the «co-catalysts». Finally, the binder has a marked effect on the stoichiometry, size, and distribution of the PtMx aggregates bearing the active sites.

Enhancing catalytic performance and hot electron generation through engineering metal-oxide and oxide-oxide interfaces

Interfaces are of utmost importance in catalytic reactions, influencing reaction kinetics and electron transfer processes. However, investigations in combined interfaces of metal-oxide and oxide-oxide at heterogeneous catalysts still have challenges due to their complex structure. Herein, we synthesized well-defined Co3O4 and CeO2 cubes with distinct facets and investigated their catalytic performance when deposited on a Pt-thin film, focusing on the influence of metal-oxide and oxide-oxide interfaces. Catalytic measurements demonstrated that the CeO2/Pt interface significantly enhanced turnover frequency (TOF) and selectivity for partial methanol oxidation compared to Co3O4/Pt and bare Pt. Notably, the CeO2/Co3O4/Pt nanodevice exhibited improved partial oxidation selectivity, highlighting the role of the CeO2/Co3O4 interface in methyl formate production. Chemicurrent measurements demonstrate enhanced hot electron generation due to increased overall TOF and partial oxidation production. We also conducted near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) analysis, revealing a higher concentration of Ce3+ ions and increased oxygen vacancies in the CeO2/Co3O4/Pt catalyst, suggesting oxygen migration from CeO2 to Co3O4, leading to methoxy species stabilization and promoting methyl formate formation.

Surface Characterization of Bacteria, Biofilms and Solid-Liquid Interfaces using Near-Ambient Pressure XPS.

Surface Characterization of Bacteria, Biofilms and Solid-Liquid Interfaces using Near-Ambient Pressure XPS.

Surface evolution of Pt/MoO3/4H-SiC(0001) investigated by in situ near-ambient pressure X-ray photoelectron spectroscopy

Achieving effective Ohmic contact between SiC and metal electrodes remains a challenge due to the high Schottky barrier resulting from the large mismatch between the deep-lying valence band of SiC and Fermi level of metals. One promising approach to address this issue is to introduce a high-work-function interfacial layer between the metal and semiconductor. However, the interaction mechanisms of the inserted high-work-function interfacial layer between metal electrodes and the SiC substrate have been rarely studied systematically. In this work, layers of high-work-function molybdenum trioxide (MoO3) and platinum (Pt) were successively grown on the 4H-SiC(0001) surface via conventional physical vapour deposition (PVD). We investigated the chemical and electronic structure evolutions upon Pt deposition on MoO3/4H-SiC(0001) using in situ near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) and ultraviolet photoelectron spectroscopy (UPS). Subsequently, the evolutions of Pt/MoO3/4H-SiC(0001) system during annealing under ultra-high vacuum (UHV) or various gas phase environments (H2 and O2) were studied via in situ NAP-XPS and UPS. Our results reveal that Pt showed its thermal stability during the annealing process, while Mo presented its versatile chemical characteristics. These results depict a detailed chemical feature of the Pt/MoO3/4H-SiC(0001) system and help gain a better understanding about the impact of different environments on Pt/MoO3 interface.

Influence of oxygen vacancies on the performance of SnO2 gas sensing by near-ambient pressure XPS studies

Modulation of oxygen vacancy (VO··) concentrations in SnO2 is an efficient strategy for improving its NO2 sensing performance. However, due to the complex reaction process between NO2 and adsorbed oxygen species on the surface of metal oxide, the role of VO·· is still unclear without in-situ characterization. Here, SnO2 nanowires (NWs) were synthesized via chemical vapor deposition method, and the VO·· concentration in SnO2 NWs was enhanced by removing adsorbed H2O on the surface of precursor during the growth process. The VO··-abundant SnO2 NWs exhibited large improvement in NO2 sensing performance with ultralow detection limit (2 ppb NO2) and high response value towards 1 ppm NO2 (49.5 at 50 °C). Near-ambient pressure X-ray photoelectron spectroscopy was used to reveal the in-situ sensing reactions occurred on the surface of SnO2 NWs. The results revealed that VO·· provided active sites for adsorption of oxygen species and confirmed the formation of NO. This work demonstrates an easy route to grow SnO2 NW with tunable VO·· concentration, and provides a direct evidence for deeper understanding of the effect of VO·· in sensing process.

Comparison of the heterogeneous reaction of NO2 on the surface of clay minerals and desert dust particles

Mineral particles in air could provide atmospheric chemical reaction interface for gaseous substances and participate in atmospheric chemical reaction process, and affecting the status and levels of gaseous pollutants in air. However, differences of the heterogenous reaction on the surface minerals particles are not very clear. Considering main mineral composition of ambient particles was from dust emission, therefore, typical clay minerals (chlorite, illite) and desert particles (Taklimakan Desert) were selected to analysize chemical reaction of NO2, one of major gaseous pollutants, on mineral particles by using of In-situ DRIFTS (diffuse reflectance infrared Fourier transform spectroscopy) under different condition. And In situ near-ambient pressure X-ray photoelectron spectroscopy (In situ NAP-XPS) was employed to investigate iron (one of the major metals) species variation on the surface of mineral dust particles during the heterogeneous reactions. Our data show that humidity controlled by deuterium oxide (D2O) has a greater effect on chemical reactions compared to light and temperature. Under dry conditions, the amount of heterogeneous reaction products of NO2 on the particles shows Xiaotang dust > chlorite > illite > Tazhong dust regardless of dark or light conditions. In contrast, under humidity conditions, the order of nitrate product quantity under moderate conditions was chlorite > illite > Xiaotang dust > Tazhong dust. In situ NAP-XPS results demonstrate that specie variation of the Fe could promote the heterogenous reactions. These data could provide useful information for understanding the formation mechanism of nitrate aerosols and removal of nitrogen oxides in the atmosphere.

Crystal-Orientation-Dependent Oxygen Exchange Kinetics on Mixed Conducting Thin-Film Surfaces Investigated by In Situ Studies.

The oxygen exchange kinetics and the surface chemistry of epitaxially grown, dense La0.6Sr0.4CoO3-δ (LSC) thin films in three different orientations, (001), (110), and (111), were investigated by means of in situ impedance spectroscopy during pulsed laser deposition (i-PLD) and near-ambient-pressure X-ray photoelectron spectroscopy (NAP-XPS). i-PLD measurements showed that pristine LSC surfaces exhibit very fast surface exchange kinetics but revealed no significant differences between the specific orientations. However, as soon as the surfaces were in contact with acidic, gaseous impurities, such as S-containing compounds in nominally pure measurement atmospheres, NAP-XPS measurements revealed that the (001) orientation is substantially more susceptible to the formation of sulfate adsorbates and a concomitant performance decrease. This result is further substantiated by a stronger increase of the work function on (001)-oriented LSC surfaces upon sulfate adsorbate formation and by a faster performance degradation of these surfaces in ex situ measurement setups. This phenomenon has potentially gone unnoticed in the discussion of the interplay between the crystal orientation and the oxygen exchange kinetics and might have far-reaching implications for real solid oxide cell electrodes, where porous materials exhibit a wide variety of differently oriented and reconstructed surfaces.

Direct Probing of Water Adsorption on Liquid-Phase Exfoliated WS2 Films Formed by the Langmuir-Schaefer Technique.

Tungsten disulfide, a transition metal dichalcogenide, has numerous applications as active components in gas- and chemical-sensing devices, photovoltaic sources, photocatalyst substrates, etc. In such devices, the presence of water in the sensing environment is a factor whose role has not been well-understood. To address this problem, the in situ probing of H2O molecule adsorption on WS2 films supported on solid substrates has been performed in a near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) setup. Instead, on the individual nanoflakes or spray-coated samples, the measurements were performed on highly transparent, homogeneous, thin films of WS2 nanosheets self-assembled at the interface of two immiscible liquids, water and toluene, transferred onto a solid substrate by the Langmuir-Schaefer technique. This experiment shows that edge defects in nanoflakes, tungsten dangling bond ensuing the exfoliation in the liquid phase, represent active sites for the WO3, WO3-x, and WO3·nH2O formation under ambient conditions. These oxides interact with water molecules when the WS2 films are exposed to water vapor in the NAP-XPS reaction cell. However, water molecules do not influence the W-S chemical bond, thus indicating the physisorption of H2O molecules at the WS2 film surface.

Surface Decorations on Mixed Ionic and Electronic Conductors: Effects on Surface Potential, Defects, and the Oxygen Exchange Kinetics.

The oxygen exchange kinetics of epitaxial Pr0.1Ce0.9O2-δ electrodes was modified by decoration with submonolayer amounts of different basic (SrO, CaO) and acidic (SnO2, TiO2) binary oxides. The oxygen exchange reaction (OER) rate and the total conductivity were measured by in situ PLD impedance spectroscopy (i-PLD), which allows to directly track changes of electrochemical properties after each deposited pulse of surface decoration. The surface chemistry of the electrodes was investigated by near-ambient pressure XPS measurements (NAP-XPS) at elevated temperatures and by low-energy ion scattering (LEIS). While a significant alteration of the OER rate was observed after decoration with binary oxides, the pO2 dependence of the surface exchange resistance and its activation energy were not affected, suggesting that surface decorations do not alter the fundamental OER mechanism. Furthermore, the total conductivity of the thin films does not change upon decoration, indicating that defect concentration changes are limited to the surface layer. This is confirmed by NAP-XPS measurements which find only minor changes of the Pr-oxidation state upon decoration. NAP-XPS was further employed to investigate changes of the surface potential step on decorated surfaces. From a mechanistic point of view, our results indicate a correlation between the surface potential and the altered oxygen exchange activity. Oxidic decorations induce a surface charge which depends on their acidity (acidic oxides lead to a negative surface charge), affecting surface defect concentrations, any existing surface potential step, potentially adsorption dynamics, and consequently also the OER kinetics.

Circumventing CO2 Reduction Scaling Relations Over the Heteronuclear Diatomic Catalytic Pair.

In the electrochemical CO2 reduction reaction (CO2RR), CO2 activation is always the first step, followed by the subsequent hydrogenation. The catalytic performance of CO2RR is intrinsically restricted by the competition between molecular CO2 activation and CO2 reduction product release. Here, we design a heteronuclear Fe1-Mo1 dual-metal catalytic pair on ordered porous carbon that features a high catalytic performance for driving electrochemical CO2 reduction to CO. Combining real-time near-ambient pressure X-ray photoelectron spectroscopy, operando 57Fe Mössbauer spectroscopy, and in situ attenuated total reflectance surface-enhanced infrared absorption spectroscopy measurements with density functional theory calculations, chemical adsorption of CO2 is observed on the Fe1-Mo1 catalytic pair through a bridge configuration, which prompts the bending of the CO2 molecule for CO2 activation and then facilitates the subsequent hydrogeneration reaction. More importantly, the dynamic adsorption configuration transition from the bridge configuration of CO2 on Fe1-Mo1 to the linear configuration of CO on the Fe1 center results in breaking the scaling relationship in CO2RR, simultaneously promoting the CO2 activation and the CO release.

Hydrogen Sensing Mechanism of WS2 Gas Sensors Analyzed with DFT and NAP-XPS.

Nanostructured tungsten disulfide (WS2) is one of the most promising candidates for being used as active nanomaterial in chemiresistive gas sensors, as it responds to hydrogen gas at room temperature. This study analyzes the hydrogen sensing mechanism of a nanostructured WS2 layer using near-ambient-pressure X-ray photoelectron spectroscopy (NAP-XPS) and density functional theory (DFT). The W 4f and S 2p NAP-XPS spectra suggest that hydrogen makes physisorption on the WS2 active surface at room temperature and chemisorption on tungsten atoms at temperatures above 150 °C. DFT calculations show that a hydrogen molecule physically adsorbs on the defect-free WS2 monolayer, while it splits and makes chemical bonds with the nearest tungsten atoms on the sulfur point defect. The hydrogen adsorption on the sulfur defect causes a large charge transfer from the WS2 monolayer to the adsorbed hydrogen. In addition, it decreases the intensity of the in-gap state, which is generated by the sulfur point defect. Furthermore, the calculations explain the increase in the resistance of the gas sensor when hydrogen interacts with the WS2 active layer.

Bimetallic NiFe Nanoparticles Supported on CeO2 as Catalysts for Methane Steam Reforming.

Ni-Fe nanocatalysts supported on CeO2 have been prepared for the catalysis of methane steam reforming (MSR) aiming for coke-resistant noble metal-free catalysts. The catalysts have been synthesized by traditional incipient wetness impregnation as well as dry ball milling, a green and more sustainable preparation method. The impact of the synthesis method on the catalytic performance and the catalysts' nanostructure has been investigated. The influence of Fe addition has been addressed as well. The reducibility and the electronic and crystalline structure of Ni and Ni-Fe mono- and bimetallic catalysts have been characterized by temperature programmed reduction (H2-TPR), in situ synchrotron X-ray diffraction (SXRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Their catalytic activity was tested between 700 and 950 °C at 108 L gcat-1 h-1 and with the reactant flow varying between 54 and 415 L gcat-1 h-1 at 700 °C. Hydrogen production rates of 67 mol gmet-1 h-1 have been achieved. The performance of the ball-milled Fe0.1Ni0.9/CeO2 catalyst was similar to that of Ni/CeO2 at high temperatures, but Raman spectroscopy revealed a higher amount of highly defective carbon on the surface of Ni-Fe nanocatalysts. The reorganization of the surface under MSR of the ball-milled NiFe/CeO2 has been monitored by in situ near-ambient pressure XPS experiments, where a strong reorganization of the Ni-Fe nanoparticles with segregation of Fe toward the surface has been observed. Despite the catalytic activity being lower in the low-temperature regime, Fe addition for the milled nanocatalyst increased the coke resistance and could be an efficient alternative to industrial Ni/Al2O3 catalysts.

NAP-XPS Probes the Electronic Structure of the Mg–Al–Cl Layered Double Hydroxide upon Controlled Hydration

The hydration of [Mg2Al(OH)6]+[Cl–, yH2O] LDH was investigated by volumetric water adsorption, X-ray diffraction, Fourier Transformed Infrared (FTIR) sepctroscopy, and Near Ambient Pressure X-ray Photoelectron Spectroscopy (NAP-XPS). It was demonstrated that water uptake into interlayer region can be quantified by NAP-XPS. The LDH’s electronic structure is assessed for increasing relative humidity (RH) up to 0.044. The Cl 2p level appears essentially unaffected by water uptake, but as supported by DFT calculation, H-bonds between chloride and water induce Cl 3p orbitals splitting. At RH = 0.7, LDH is covered by a water film that contains Mg and Cl species but no Al. Soft X-ray radiolysis of hydrated Cl species induces the formation of oxidized Cl species.

Disordered Au Nanoclusters for Efficient Ammonia Electrosynthesis.

The electrochemical nitrogen (N2 ) reduction reaction (N2 RR) under mild conditions is a promising and environmentally friendly alternative to the traditional Haber-Bosch process with high energy consumption and greenhouse emission for the synthesis of ammonia (NH3 ), but high-yielding production is rendered challenging by the strong nonpolar N≡N bond in N2 molecules, which hinders their dissociation or activation. In this study, disordered Au nanoclusters anchored on two-dimensional ultrathin Ti3 C2 Tx MXene nanosheets are explored as highly active and selective electrocatalysts for efficient N2 -to-NH3 conversion, exhibiting exceptional activity with an NH3 yield rate of 88.3±1.7 μg h-1 mgcat. -1 and a faradaic efficiency of 9.3±0.4 %. A combination of in situ near-ambient pressure X-ray photoelectron spectroscopy and operando X-ray absorption fine structure spectroscopy is employed to unveil the uniqueness of this catalyst for N2 RR. The disordered structure is found to serve as the active site for N2 chemisorption and activation during the N2 RR process.

Near ambient pressure–x-ray photoelectron spectroscopy spectra of lithium hexafluorophosphate in ethylene/dimethyl carbonate

Near ambient pressure–x-ray photoelectron spectroscopy (NAP-XPS) is a less traditional form of XPS that allows samples to be analyzed at relatively high pressures, i.e., at greater than 5000 Pa. NAP-XPS can probe moderately volatile liquids, biological samples, porous materials, and/or polymeric materials that outgas significantly. In this submission, we show the survey, Li 1s, P 2p, C 1s, N 1s, O 1s, and F1s NAP-XPS spectra of a Li-based electrolyte solution, which is a material that would be difficult to analyze by conventional XPS. The measurements were performed at 1000 Pa in ambient gas atmosphere to compensate for surface charging. Peak fits of the C 1s, O 1s, and F 1s narrow scans are presented.

Near ambient pressure–x-ray photoelectron spectroscopy spectra of lithium bis(trifluoromethane-sulfonyl) imide in propylene carbonate

Near ambient pressure–x-ray photoelectron spectroscopy (NAP-XPS) is a less traditional form of XPS that allows samples to be analyzed at relatively high pressures, i.e., at greater than 5000 Pa. NAP-XPS can probe moderately volatile liquids, biological samples, porous materials, and/or polymeric materials that outgas significantly. In this submission, we show the survey, Li 1s, S 2p, C 1s, N 1s, O 1s, and F 1s NAP-XPS spectra of a Li-based electrolyte solution, which is a material that would be difficult to analyze by conventional XPS. The measurements were performed at 200 Pa in ambient gas atmosphere to compensate for surface charging. Peak fits of the C 1s, O 1s, and F 1s narrow scans are presented.

Effect of Water Vapor on Oxidation Processes of the Cu(111) Surface and Sublayer.

Copper-based catalysts have different catalytic properties depending on the oxidation states of Cu. We report operando observations of the Cu(111) oxidation processes using near-ambient pressure scanning tunneling microscopy (NAP-STM) and near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS). The Cu(111) surface was chemically inactive to water vapor, but only physisorption of water molecules was observed by NAP-STM. Under O2 environments, dry oxidation started at the step edges and proceeded to the terraces as a Cu2O phase. Humid oxidation of the H2O/O2 gas mixture was also promoted at the step edges to the terraces. After the Cu2O covered the surface under humid conditions, hydroxides and adsorbed water layers formed. NAP-STM observations showed that Cu2O was generated at lower steps in dry oxidation with independent terrace oxidations, whereas Cu2O was generated at upper steps in humid oxidation. The difference in the oxidation mechanisms was caused by water molecules. When the surface was entirely oxidized, the diffusion of Cu and O atoms with a reconstruction of the Cu2O structures induced additional subsurface oxidation. NAP-XPS measurements showed that the Cu2O thickness in dry oxidation was greater than that in humid oxidation under all pressure conditions.

Probing dynamic covalent chemistry in a 2D boroxine framework by in situ near-ambient pressure X-ray photoelectron spectroscopy.

Dynamic covalent chemistry is a powerful approach to design covalent organic frameworks, where high crystallinity is achieved through reversible bond formation. Here, we exploit near-ambient pressure X-ray photoelectron spectroscopy to elucidate the reversible formation of a two-dimensional boroxine framework. By in situ mapping the pressure-temperature parameter space, we identify the regions where the rates of the condensation and hydrolysis reactions become dominant, being the key to enable the thermodynamically controlled growth of crystalline frameworks.

In situnear-ambient pressure X-ray photoelectron spectroscopy reveals the effects of water, oxygen and light on the stability of PM6:Y6 photoactive layers

To better understand the effects of water and oxygen on OSC materials’ stability,i.e.PM6 and Y6, we usedin situnear-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) to investigate the electronic structures.