Nanofiber Webs Research Articles

Improved Sheet Resistance of Nanofiber-Based Transparent Conducting Electrodes Using Silver Nanowires.

There is an increased need for research on flexible transparent electrodes (FTEs) because they are critical to next-generation electronic devices, such as wearable computers. In this study, highly conductive transparent conducting electrodes, based on polyvinylidene fluoride (PVDF) nanofiber webs treated with poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and silver nanowires (AgNWs), were successfully fabricated. Transparent conducting electrodes (TCEs) were obtained by a brush-painting process using different weight ratios of a AgNWs to PEDOT:PSS solution, and the surface, electrical, optical, and chemical properties, as well as the tensile strength of the samples, were determined. It was found that the electrical conductivity of the samples improved as the AgNW content increased, but the light transmittance decreased. In this work, there was a slight decrease in the optical properties and a considerable increase in the electrical properties due to the hybridization of AgNWs and PEDOT:PSS, compared to using only PEDOT:PSS. When considering both transparency and electrical conductivity, which are essential parameters of TCEs, sample PA2, which was treated by mixing AgNWs and PEDOT:PSS/dimethyl sulfoxide (DMSO) in a ratio of 1:5 (16.67 wt% of AgNWs), was found to be the best sample, with a sheet resistance of 905 Ω/cm2 and light transmittance of 79%.

Effect of Process Control Parameters on the Filtration Performance of PAN-CTAB Nanofiber/Nanonet Web Combined with Meltblown Nonwoven.

Nanofibers have potential applications as filters for particles with diameters <10 μm owing to their large specific surface area, macropores, and controllable geometry or diameter. The filtration efficiency can be increased by creating nanonets (<50 nm) whose diameter is smaller than that of nanofibers. This study investigates the effect of process conditions on the generation of nanonet structures from a polyacrylonitrile (PAN) solution containing cation surfactants; in addition, the filtration performance is analyzed. The applied electrospinning voltage and the electrostatic treatment of meltblown polypropylene (used as a substrate) are the most influential process parameters of nanonet formation. Electrospun polyacrylonitrile–cetylmethylammonium bromide (PAN–CTAB) showed a nanofiber/nanonet structure and improved thermal and mechanical properties compared with those of the electrospun PAN. The pore size distribution and filter efficiency of the PAN nanofiber web and PAN–CTAB nanofiber/nanonet web with meltblown were measured. The resulting PAN–CTAB nanofiber/nanonet air filter showed a high filtration efficiency of 99% and a low pressure drop of 7.7 mmH2O at an air flow rate of 80 L/min. The process control methods for the nanonet structures studied herein provide a new approach for developing functional materials for air-filtration applications.

New Insights toward Casein/Polyvinyl Alcohol Electrospun Nanofibrous Webs as a Piezoelectric-Cum-Triboelectric Energy Harvester

New Insights toward Casein/Polyvinyl Alcohol Electrospun Nanofibrous Webs as a Piezoelectric-Cum-Triboelectric Energy Harvester

Feasibility study on the application of electrospun nanofiber webs for the air sampling of crystalline silica.

The aim of the present study was to first fabricate an electrospun PVC nanofiber web and then assess its applicability in sampling and measuring the concentration of airborne crystalline silica by comparing analysis results with a commercial PVC membrane filter under different ranges of airborne silica concentration. A filtration performance comparison was also made between an electrospun PVC web with nano-sized fibers and a commercial PVC membrane filter. Overall, the measured concentration of silica by the electrospun webs was 1.022 times higher than that of the commercial PVC filter in all studied ranges of silica concentration and the nanofiber media had higher filtration efficiency and lower pressure drop compared to the PVC membrane filter. This can be considered to be due to the lower fiber diameter and greater porosity (obtained from the 2D SEM image) of the electrospun nanofiber webs. This makes them suited for air pollutant sampling and determining its airborne concentration.

Sound absorption and thermal insulation properties of composite thermoplastic polyurethane/polystyrene (TPU/PS) nanofiber web and TPU nanofiber web and PS-extracted TPU/PS microfiber web

In this study, composite thermoplastic polyurethane (TPU)/polystyrene (PS) nanofiber web and TPU nanofiber web and PS-extracted TPU/PS microfiber web have been experimentally investigated with regard to sound absorption and thermal conductivity coefficients to observe a potential use in sound and thermal insulation areas. Moreover, other properties such as surface area, morphology, tensile strength/elongation, air permeability, and thermal degradation have been analyzed. It has been observed that nanofiber web properties such as fiber diameter, extensibility, pore volume, and porosity have been clearly changed by Soxhlet extraction of PS from the composite TPU/PS nanofibers. PS-extracted TPU/PS fibers can be preferred for the low frequency (600–800 Hz) due to higher SAC (0.7). On the other hand, TPU nanofibers were more effective at medium frequencies (around 3000 Hz, SAC 0.6). Both TPU and PS-extracted TPU/PS composite fibers had similar thermal conductivities, whereas TPU/PS composite nanofibers had lowest thermal conductivity (0.05 W/mK) with moderate maximum SAC value (around 1000 Hz, SAC 0.5–0.6).

Effect of solution blown nanofibers on Mode‐I fracture toughness and dynamic mechanical properties of carbon fiber‐reinforced composites

AbstractIn this study, solution‐blown nanofibers were coated on carbon fiber (CF) fabrics to improve Mode‐I fracture toughness and dynamic mechanical properties of the composite laminates. Nanofiber coatings of various basis weights were directly spun over CF fabrics, which were then formed into composite laminates via vacuum‐assisted resin transfer molding. A double cantilever beam test was conducted to analyze the Mode‐I fracture toughness of CF‐reinforced epoxy composites. The results showed that solution‐blown nanofiber coatings stabilized the crack propagation and increased the delamination strength hence increased the Mode‐I fracture toughness by nearly 48% for the addition of 1 g/m2 nanofibrous web. Dynamic mechanical analysis was performed to investigate the effect of nanofibers on the stiffness of materials and the homogeneity of samples. Storage modulus, loss modulus, and damping factor were calculated, and corresponding Cole‐Cole plots were drawn. DMA results showed that the stiffness of the composite sample increased up to 17% even after a minor amount (1 g/m2) of nanofiber coating.

Conductive and antibacterial cellulose nanofibers decorated with copper nanoparticles for potential application in wearable devices

AbstractOne of the contributions of nanotechnology to our daily life is the preparation of a large variety of polymer‐based nanofibers, which could be the basis of future wearable devices. Wearable electronics are a great part of smart textiles research. Herein, we have reported an easy method to fabricate electrically conductive cellulose nanofibers (CNFs). To fabricate CNFs, we first prepared cellulose acetate (CA) nanofibers by using the electrospinning technique and later, the deacetylation process was done to obtain the CNFs. The electroless deposition (ELD) technique was then used to create the conductive nanofibers. Copper (Cu) was used to coat the CNFs because of their high conductivity and low cost. The ELD process parameters including time, temperature, volume, and pH were optimized to obtain a nanofiber with higher conductivity. The optimized condition was temperature: 40 °C, time: 10 min, volume: 600 ml, and pH: 13 to obtain a nanofiber web with 983.5 S/cm conductivity. Cu‐coated CNFs were characterized by scanning electron microscope, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, water contact angle, antibacterial activity, tensile, and electrical conductivity. The bending cycle test was performed to quantitatively demonstrate the durability and flexibility of the Cu‐coated nanofibers. Cu‐coated CNFs exhibited great performance to be used as a conductive layer with antibacterial activity.

An investigation into the designing of fibrous sound absorption materials incorporated with nanofibers: a case study of a multi-layered material composed of PET nonwoven and PAN nanofibers

The present work aimed to investigate the effect of nanofiber enhancement on the sound absorption performance of fibrous materials through a brief review of the recent progress in the field and highlight the current challenges and issues for measuring and modeling the sound absorption coefficient (SAC) of such structures. Moreover, some composite samples consist of polyethylenterephthalat (PET) nonwoven fabric and polyacrylonitrile (PAN) nanofibers web were prepared to be studied as a case study. The nanofiber deposition amounts, nanofiber orientation, and nanofiber layering sequence were chosen as the main variables of samples. Various amounts of deposition were achieved through three different electrospinning (ES) time of 15, 60, and 180 min. The random and aligned orientation of the nanofiber web was obtained by using a rotating collector. The effect of the layering sequence of the nanofiber layer was studied in the form of quadruple-layered assemblies of samples. The results showed that the samples incorporated with the nanofiber layer with 60 min of ES and random orientation when it is used in the second position of the layering sequence have the best performance of sound absorption, mainly at lower critical frequency range. Furthermore, a discussion on some available empirical models and compare the results confirms that there is a need for developing a new approach for measuring and modeling the SAC and consequently designing such absorbers.

Fabrication of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate)/Poly(vinylidene fluoride) Nanofiber-Web-Based Transparent Conducting Electrodes for Dye-Sensitized Photovoltaic Textiles.

In this work, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/poly(vinylidene fluoride) (PVDF) nanofiber-web-based transparent conducting electrodes (TCEs) were fabricated for use in dye-sensitized photovoltaic textiles. The PEDOT:PSS solution was mixed with dimethyl sulfoxide (DMSO) solvent, and the PEDOT:PSS/DMSO mixture was applied on the PVDF nanofiber web using a simple brush-painting technique to prepare ultrathin and -lightweight, highly transparent TCEs. When the PVDF nanofiber web was treated with a 3:7 PEDOT:PSS and DMSO mixture (P3D7 sample), it exhibited ∼84% transmittance at a wavelength of 550 nm with an average sheet resistance of ∼1.5 kΩ/sq. In addition, it showed a figure of merit (FOM) of 0.104 × 10-3 Ω-1. In the trial test, the P3D7 TCE-based photovoltaic textile exhibited an average voltage of 73.20 mV and an average current of 0.44 mA/cm2.

Formononetin/methyl-β-cyclodextrin inclusion complex incorporated into electrospun polyvinyl-alcohol nanofibers: Enhanced water solubility and oral fast-dissolving property

Improving solubility and administration route of isoflavone formononetin (FMN) are critical factors to improve its bioavailability in the oral cavity. This study fabricated fast-dissolving nanofibers containing FMN/methyl-β-cyclodextrin (FMN/Me-β-CD) inclusion complex. The solubility of FMN could be increased by approximately 50 times at 20 mM aqueous Me-β-CD. Interactions and thermodynamic parameters of the host-guest inclusion complex were studied by a fluorescence quenching method. The structure and mechanisms of the complex were further studied by molecular docking and molecular dynamics. Finally, polyvinyl-alcohol (PVA) nanofibrous webs containing the FMN/Me-β-CD inclusion complex were fabricated by electrospinning. The dissolution test demonstrated that the FMN/Me-β-CD/PVA nanofibers can be dissolved in artificial saliva within approximately 2 s. This study shows the potential of Me-β-CD inclusion and electrospinning to improve solubility and administration route of isoflavones.

Fabrication of Poly (Acrylonitrile-Co-Methyl Methacrylate) Nanofibers Containing Boron via Electrospinning Method: A Study on Size Distribution, Thermal, Crystalline, and Mechanical Strength Properties

Electrospun polymeric nanofibers have attracted great attention in filtration systems and protective clothes. One of them is polyacrylonitrile (PAN) nanofibers, which are a suitable choice for the fabrication of protective clothes in the defense industry, due to their good fiber formation and easy optimization with chemical reagents. They do not possess adequate properties for protection against chemical, biological, and radiological agents. In this research, poly (acrylonitrile-co-methyl methacrylate) (PANMM) nanofibers and PANMM nanofibers containing 10B were fabricated via the electrospinning method. The study of the morphology of nanofibers, using scanning electron microscopy (SEM), revealed that smooth and knotted fibers with an average diameter of 259 ± 64 nm were obtained, using 12% (w/v) of PANMM in the solution as the optimal concentration for the electrospinning process. This sample was doped with boron (10%, 30%, and 50% (w/w)) to fabricate the samples of PANMM + boric acid (BA) nanofibers. The results demonstrated an increasing trend in the diameter of the nanofibers with an increase in BA up to 50%. At this concentration, smooth fibers were formed with lower knots. Furthermore, the presence of B-O and O-H groups was observed using Fourier transform infrared (FTIR) spectroscopy. To study the tensile properties, the nanofibrous web was tested, and the results showed that introducing 10B to PANMM nanofiber structures reduced the strength of the nanofibers. Thermal gravimetric analysis (TGA) showed that BA-modified PANMM nanofibers had lower thermal degradability, as compared with pure PANMM.

Gallic Acid/2-Hydroxypropyl-β-cyclodextrin Inclusion Complexes Electrospun Nanofibrous Webs: Fast Dissolution, Improved Aqueous Solubility and Antioxidant Property of Gallic Acid

Gallic acid(GA) is a kind of natural polyphenolic compound, but its low aqueous solubility restricts its application in the fields of food and medicine. Cyclodextrin can form inclusion complexes with guest molecules(e.g., essential oils, food supplements) through cavities with special properties to improve aqueous solubility, thermal stability, and bioavailability of guest molecules. In this research, gallic acid/2-hydroxypropyl-β-cyclodextrin inclusion complexes(GA/2-HP-β-CD/ICs) were formed in a highly concentrated solution of 2-HP-β-CD. Bead-free and uniform nanofibrous webs(GA/2-HP-β-CD/IC-NWs) were produced successfully by electrospun GA/HP-β-CD/IC aqueous solution. The initial molar ratio(GA: 2-HP-β-CD=1:1) of GA/2-HP-β-CD/IC in the solutions was largely maintained in GA/2-HP-β-CD/IC-NW. The aqueous solubility of GA was enhanced and GA/2-HP-β-CD/IC-NW has displayed fast dissolution property. Furthermore, in comparison with GA powder, GA/2-HP-β-CD/IC-NW demonstrated improved antioxidant capacity. The results suggested that GA/2-HP-β-CD/IC-NW have broad application prospects as orally fast dissolution systems for food supplements.

Synthesis and Characterization of Exopolysaccharide Encapsulated PCL/Gelatin Skin Substitute for Full-Thickness Wound Regeneration.

Loss of skin integrity can lead to serious problems and even death. In this study, for the first time, the effect of exopolysaccharide (EPS) produced by cold-adapted yeast R. mucilaginosa sp. GUMS16 on a full-thickness wound in rats was evaluated. The GUMS16 strain’s EPS was precipitated by adding cold ethanol and then lyophilized. Afterward, the EPS with polycaprolactone (PCL) and gelatin was fabricated into nanofibers with two single-needle and double-needle procedures. The rats’ full-thickness wounds were treated with nanofibers and Hematoxylin and eosin (H&E) and Masson’s Trichrome staining was done for studying the wound healing in rats. Obtained results from SEM, DLS, FTIR, and TGA showed that EPS has a carbohydrate chemical structure with an average diameter of 40 nm. Cell viability assessments showed that the 2% EPS loaded sample exhibits the highest cell activity. Moreover, in vivo implantation of nanofiber webs on the full-thickness wound on rat models displayed a faster healing rate when EPS was loaded into a nanofiber. These results suggest that the produced EPS can be used for skin tissue engineering applications.

Highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/nylon 6 nanofiber web treated with repetitive coating cycles and dimethyl sulfoxide multi-step treatment for electronic textiles

Highly conductive nylon 6 nanofiber web was fabricated with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and dimethyl sulfoxide (DMSO) for electronic textiles. To improve electrical conductivity, repeated coating with PEDOT:PSS and multi-step treatment of DMSO was performed. The effects of these treatments on electrical conductivity, surface properties, and chemical structures were investigated. For repetitive coating cycles, pristine PEDOT:PSS dispersion was dropped onto a nylon 6 nanofiber web for between one and four times of coating. For DMSO multi-step treatment, in the one-step treatment, the nanofiber web was repeatedly treated using PEDOT:PSS doped with DMSO. In the two-step treatment, the nanofiber web was repeatedly treated with doped PEDOT:PSS at first and, then, it was immersed in a DMSO bath. As a result, the sheet resistance decreased dramatically as the number of coating cycles increased. When the two-step treatment was applied, the sheet resistance was much lower compared to that of the one-step treatment, and thereby sample PD4-D with the lowest resistance showed 6.56 Ω/sq. As a result, the surface of the nanofiber web was covered with more PEDOT:PSS as the coating cycle was repeated. The PEDOT particles became large and long shapes after the two-step treatment of DMSO. This inferred that the contact area among conducting PEDOT particles increased because insulating PSS was removed by DMSO. In addition, the presence of PEDOT:PSS and nylon 6 was confirmed. This study proved that the simultaneous treatments of repeated coating with PEDOT:PSS and multi-step treatment of DMSO can improve electrical conductivity, and it developed the highly conductive PEDOT:PSS/nylon 6 nanofiber web.

Large-Scale Centrifugal Multispinning Production of Polymer Micro- and Nanofibers for Mask Filter Application with a Potential of Cospinning Mixed Multicomponent Fibers.

Recently, the polymer nanofiber web is in high demand as a strong barrier against harmful particles due to its high capture efficiency and strong droplet-blocking ability. As an advanced spinning technique, the centrifugal multispinning system was designed by sectioning a rotating disk into triple subdisks, showing mass producibility of polymer nanofibers with cospinning ability. Using the system, gram-scale production of polystyrene (PS), poly(methyl methacrylate), and polyvinylpyrrolidone (PVP) was demonstrated, showing a possibility for versatile use of the system. Moreover, a high production rate of ∼25 g/h for PS nanofibers was achieved, which is ∼300× higher than that of the usual electrospinning process. Utilizing the cospinning ability, we controlled the contact angle and electrostatic charge of the multicomponent nanofiber web by adjusting the relative amounts of PS and PVP fibers, showing a potential for functional textile application. With the fabricated PS nanofiber-based filters, we achieved high capture efficiency up to ∼97% with outstanding droplet-blocking ability.

The biopolymer ulvan from Ulva fasciata: Extraction towards nanofibers fabrication

As a biocompatible polymer, ulvan has applications in countless fields. Therefore, the following study intends to extract ulvan from Ulva fasciata, emphasizing its use for biomedical and industrial applications in the manufacture of nanofibrous webs. The extracted ulvan was characterized using FT-IR, DSC, XRD, GPC, and NMR. The extracted ulvan's FT-IR spectra confirmed that it is a sulfated polysaccharide. The HPLC analysis showed that the extracted ulvan is composed of rhamnose, xylose, glucose and glucuronic acid. NMR showed that the proton chemical shifts at 1.3 are due to methyl protons of rhamnose 3-sulfate in the ulvan samples. The X-ray diffractograms suggested that the extracted ulvan is semi-crystalline polymer with major crystalline reflection at 2θ of 29.4°. Deionized water has been successfully used to produce ulvan/polyvinyl alcohol (ulvan/PVA) nanofibers as an eco-friendly solvent. It was found that the ulvan-to-PVA (1:2) ratio results in nanofiber that is well handled and smooth. In addition to pretreated ones, the ulvan extracted without organic solvent pretreatment showed bead free nanofibers. It is concluded that pretreatment with organic solvent in ulvan extraction, particularly in the manufacture of nanofibers, is not recommended. In addition, the resulting nanofibrous mat has sufficient mechanical properties for various applications to be incorporated.

Electrospun Polycaprolactone Nanofibrous Webs Containing Cu–Magnetite/Graphene Oxide for Cell Viability, Antibacterial Performance, and Dye Decolorization from Aqueous Solutions

Fine powder of magnetite nanoparticles (MNPs) was doped with different contents of copper (Cu) through a mat of graphene oxide (GO) nanosheets. These compositions were incorporated into electrospun nanofibrous membranes of polycaprolactone (PCL). Mechanical properties were measured, and examining the ability of these nanofiber membranes to remove methylene blue (MB) dyes from aqueous solutions was also assessed. TEM of the resulting nanofibers has a diameter of the order of 300 nm. Moreover, the morphological features of membranes showed that diameters were varied upon the variation of dopant (Cu ions) starting from 0.35–1.06 μm and 1.8–3.9 μm at no Cu reaching 0.19–0.45 μm and 0.75–1.42 μm for the highest contribution of Cu, whereas GO scattered grains of 0.56–1.5 μm were detected. The tensile strength was changed accordingly and reached around 8.96 ± 0.45 MPa, while the toughness achieved 4.69 ± 0.29 MJ/m3 at the highest additional dopant. The designed nanofibrous membrane was able to remove 95.1% MB after 36 min of continuous exposure, while the reusability indicated that the composition was stable after 5 times of removal with efficiency around 90.1% for the 0.8Cu–MNPs–GO@PCL. The antibacterial efficiency was also investigated against both E.coli and S. aureus, and the inhibition zone recorded around 11.4 ± 1.5 and 11.1 ± 1.7 mm in dark and 15.6 ± 2.1 and 13.6 ± 1.8 mm, respectively, at the highest contribution of Cu dopant. This behavior of the manipulated nanofibrous membrane indicates that tailoring of multi-functional nanomaterials could be reached via designing scaffold-based electrospun technique.

Antibacterial, thermal decomposition and in vitro time release studies of chloramphenicol from novel PLA and PVA nanofiber mats

The present investigation is the first report containing design and synthesis of novel calixarene derivatives (6–8) and their inclusion complexes (IC6–IC8) with Chloramphenicol (CAM). After synthesis, the antibiotic CAM, calixarene derivatives (6–8) and their inclusion complexes (IC6–IC8) were successfully incorporated into biodegradable PVA and/or PLA nanofiber skeleton by electrospinning. The obtained electrospun nanofibers were tested and compared for inhibition of bacterial growth towards multiple bacterial species (Escherichia coli, and Bacillus subtilis). Moreover, we evaluated thermal decomposition and release profile of CAM by spectrophotometric methods. The results suggested that CAM can be successfully encapsulated in nanofiber webs by inclusion complexation, and these fibers could be used as a part of new controlled release packaging system for food preservation.

Engineered NiCo-LDH nanosheets- and ZnFe2O4 nanocubes-decorated carbon nanofiber bonded mats for high-rate asymmetric supercapacitors

In this work, we have prepared the hierarchically nanostructured core–shell NiCo layered double hydroxide (NiCo-LDH) nanosheets- and ZnFe2O4 nanocubes-decorated polyacrylonitrile (PAN)/pitch-based carbon nanofibers (PPCNs) webs (NiCo-LDH@PPCNs as cathode and ZnFe2O4@PPCNs as anode materials) with the bonded network structure by a facile and scalable hydrothemal method. Herein, the low-cost pitch with lower softening point (∼90 °C) as co-precursor was utilized to produce the PAN/pitch-based carbon nanofibers (PPCNs) with enhanced electrical conductivity. The obtained PPCNs with pitch content of 30% (PP30CNs) electrode material delivered higher specific capacitance (∼67 F g−1) than that (∼48 F g−1) of the PAN-based carbon nanofibers (PCNs) at 1 A g−1, due to the increased electrical conductivity and lower interfacial charge transfer resistance (RCT) of ∼0.16 Ω. Further, the NiCo-LDH-decorated PP30CNs (NiCo-LDH@PP30CNs) as cathode material showed superior specific capacitance of 1162 F g−1 at 1.0 A g−1 and ultra-high retention rate of 91.56% at 10 A g−1. The ZnFe2O4@PP30CNs as anode material also showed higher specific capacitance of 282 F g−1 at 1 A g−1 and good rate capability with capacitance retention of 56.73% at 10 A g−1. The as-fabricated asymmetric NiCo-LDH@PP30CNs//ZnFe2O4@PP30CNs hybrid supercapacitor device delivered a specific capacitance of ∼98 F g−1 at 1 A g−1 and excellent capacitance retention of ∼88% after 5000 charge–discharge cycles.

Nylon 6 Nanofiber Web-Based Signal Transmission Line Treated with PEDOT:PSS and DMSO Treatment.

Highly conductive nylon 6 nanofiber webs, incorporating poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and dimethyl sulfoxide (DMSO), were prepared for textile-based signal transmission lines. To improve the electrical performance of the textiles, they were optimized by the number of coating cycles and the solvent treatment step. The nanofiber web coated four times with PEDOT:PSS showed a six-times reduction in sheet resistance compared to that of once. In addition, the sample treated with both adding and dipping of DMSO showed a significant decrease of 83 times in sheet resistance compared to the sample without treatment of DMSO. Using samples with excellent electrical conductivity, the waveforms of the signal in the time domain were analyzed and shown to have an amplitude and phase almost identical to that of the conventional copper wire. As a result of the S21 characteristic curve, selected textiles were available up to the 15 MHz frequency bandwidth. In the FE-SEM image, it was observed that the surface of the coated sample was generally covered with PEDOT:PSS, which was distinguished from the untreated sample. These results demonstrate that the nanofiber web treated with the optimized conditions of PEDOT:PSS and DMSO can be applied as promising textile-based signal transmission lines for smart clothing.