Multiplexing Signals Research Articles

SOA-MZI Differential Transformation Approach Applied on Simultaneous Electro-Optical Mixing

We experimentally incubate a ground-breaking design, for the first time, of concurrent electro-optical semiconductor optical amplifier Mach–Zehnder interferometer mixing (SOA-MZI) based on a differential transformation methodology. Projecting the simultaneous electro-optical mixing system and improving its efficiency and quality achievement in optical and electrical features is a crucial task due to the characteristics of an optical pulse source (OPS) operating with a repetition rate of f= 58.5 GHz and a pulse width duration of 1 picosecond (ps). The resultant of the contemporaneous electro-optical mixing exhibits exceptional passive power stability, reaching 0.8% RMS over a two-hour period. Furthermore, when the optical bandpass filter is controlled at the data wavelength of 1540 nm, we achieve up to 30 dBm of the overall mean output power with an optical conversion gain of 46 dB and an exceptionally high optical signal-to-noise ratio reaching 80 dB. Using orthogonal frequency division multiplexing (OFDM) signals, each data subcarrier is modulated using 128 quadratic amplitude modulation (128-QAM) at carrier frequencies fk and simultaneously up-mixed to high aim frequencies nf±fk at the SOA-MZI output. Additionally, the resulting OFDM_128-QAM up-mixed signal is examined using the specifications for the error vector magnitudes (EVMs) and the electrical conversion gains (ECGs). The SOA-MZI mixing experiment can handle high frequencies up to 120 GHz. Positive ECGs are followed by a sharp reduction over the entire band of the aim frequencies. The highest frequency range achieved during the realistic investigation is shown at 2f+f4= 120 GHz, where the EVM reaches 8% with a symbol rate of 15 GSymb/s. Furthermore, the concurrent OFDM_128-QAM up-mixed signal achieves an absolute maximum bit rate of 80.4 Gbit/s. The investigation into the simultaneous electro-optical mixing regime is finally supported by unmatched characterization improvements.

Support 16384QAM mobile fronthaul based on 3 amplitude quantization Delta-Sigma Modulation

We experimentally demonstrated 16384-ary quadrature amplitude modulation (16384QAM) mobile fronthaul based on 3-amplitude quantization high-pass Delta-sigma Modulation (DSM) in the O band intensity-modulated direct detection (IM/DD) system. By using 3-amplitude quantized high-pass DSM, we successfully quantize the analog waveform of intermediate frequency (IF) Orthogonal Frequency Division Multiplexing (OFDM) signal into 3-Level Pulse Amplitude Modulation (PAM3) signal, and 1 GHz bandwidth 16384-QAM and 1024QAM are successful transmission in 20Gb/s IM/DD link. 0.63% Error Vector Magnitude (EVM) of 16384QAM and 0.7% EVM of 2048QAM are achieved after 25km SSMF and 50km SSMF transmission, respectively. The signal-to-noise ratio (SNR) of the retrieved OFDM signal is 43 dB, which shows that the proposed scheme can support 16384QAM mobile fronthaul network.

Bidirectional Cladding-Pumped Multicore EDFA and its Optimization for Energy Efficiency by Tuning Pump Condition

This work investigates the feasibility of improving the energy efficiency of a cladding-pumped multicore (MC) EDFA by utilizing bidirectional (BD) pumping. We combined a conventional forward-cladding-pumped MC-EDFA with backward cladding pumping and tuned the pump-gain characteristics and gain shape by controlling the optical pump power ratio of its forward and backward pumps. Since EDFAs have wavelength dependence, output power equalization by each wavelength channel is extremely important for amplifying the wavelength division multiplexing (WDM) signal. The standard method of current equalization is to adjust the attenuation by the output power of each wavelength channel. The main issue with the current standard equalization is the indispensable optical power loss caused the reduced optical amplification efficiency of the EDFA. Our previous work demonstrated that the optical power loss due to equalization can be reduced by controlling the optical power ratio of the forward and backward pumps. This leads to improved energy efficiency of the signal amplification and equalization of both the WDM and spatial division multiplexing (SDM). <p xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">In this paper, we report our detailed investigation into the tuning amplification characteristics of the BD-MC-EDFA. Our main focus was the gain, noise figure (NF), and gain shape of a 7-core BD-MC-EDFA prototype when forward and backward optical pump power was changed. Under 8 W of total optical pump power, the percentage of 60% forward cladding optical pump power was found to be optimal for efficiency considering the minimum output optical power loss due to equalization. This condition translates into a 1.7% pump conversion efficiency (PCE) improvement, which corresponds to a 24% reduction of the total optical pump power compared to conventional MC-EDFA with only forward cladding pumping. Although the NF deteriorated by 1.0 dB in wavelength average in the 4.5-THz signal bandwidth in exchange for the efficiency improvement, degradation of the 34.2-GBaud polarization multiplexed 16 quadrature amplitude modulation (PM-16QAM) signal amplified by the BD-MC-EDFA operated under the optimized condition was negligible.

Orthogonal frequency‐division multiplexing‐based signal design for a dual‐function radar‐communications system using circulating code array

AbstractIn this study, a dual‐function radar‐communications (DFRC) system based on the circulating code array is presented to address the contradiction between radar and communications system in beam scanning and beam coverage. Processed orthogonal frequency‐division multiplexing (OFDM) signal is transmitted by the circulating code array as the base signal to improve the data rate. Following the spatial angle of the communication receiver, the communication symbols are modulated to part of OFDM signal subcarriers occupying a specific frequency band. A significant property of the circulating code array, which provides a relationship between the baseband frequency of the base signal and the spatial angles, implements a basis for safe telecommunication transmission towards the cooperative receiver and demodulation. Moreover, the circulating code array transmits the same signal and introduces the same time interval between adjacent array elements. Therefore, the complex problems of multi‐dimensional orthogonal signal design in the traditional multiple‐input‐multiple‐output‐based DFRC system design are transformed into a simple base signal design. Finally, an omnidirectional coverage pattern is obtained. Thus, whether the communication receiver is in the mainlobe or the sidelobe of the radar beam, the communication connection can be established between the designed DFRC system and the communication users. The performance of the described DFRC system is verified through theoretical analysis and simulations.

On the Mitigation of WSS Filtering Penalties: Single- vs Multi-Carrier Modulation

The tight channel filtering imposed by long cascades of reconfigurable optical add-drop multiplexers (ROADMs) represents, nowadays, one of the major performance-limiting aspects for optically-routed coherent optical fiber systems. This makes it vital to perform a ROADM-aware optimization of the network performance at the physical layer. In particular, the use of different modulation options is known to have a strong impact on the extent of the filtering-induced penalties. In that regard, a long debate between single- and multi-carrier modulation has been taking place during the last few years, sometimes leading to apparently contradictory results. Following the open scientific discussion on this topic, in this work, we investigate by simulation and experimentally the wavelength selective switch (WSS) filtering tolerance of single-carrier (SC) and digital subcarrier multiplexing (DSCM) signals. In order to promote a fair comparison, both modulation options are carefully designed to minimize the ROADM-filtering penalties, namely resorting to the use of entropy loading together with baud rate optimization. After some preliminary numerical assessment, a comprehensive set of experiments are carried out for the transmission of 21-WDM 95–105 Gbaud SC and DSCM signals over a 2040 km straight line of fiber with regularly spaced WSSs. In general, our results allow to conclude that the two modulation options yield similar performance if the overall baud rate is optimized for each filtering scenario, keeping the baud rate at <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$\pm$</tex-math></inline-formula> 5% of the optimized value.

Coordinated-security based on probabilistic shaping and encryption in MMW-RoF system.

A coordinated-security probabilistic shaping (PS) physical layer encryption scheme is proposed for a W-band millimeter-wave radio-over-fiber (MMW-RoF) system. This scheme mainly includes substituting encryption, coordinated encrypted PS, and unequal length grouping scrambling, which can realize the coordination between PS and chaotic encryption. The key space of the proposed scheme is 10103, which can effectively prevent against brute force cracking and chosen-plaintext attacks. The encrypted orthogonal frequency division multiplexing (OFDM) signal is successfully transmitted over 50-km standard single-mode fiber (SSMF) and a 5-m wireless channel. The results show that the proposed scheme achieves 0.8-dB received optical power gain at a bit error rate (BER) of 10-3 compared with a traditional OFDM signal. The superiority of the proposed scheme in security performance and BER performance has been verified.

Scalable High-Precision Trimming of Photonic Resonances by Polymer Exposure to Energetic Beams.

Integrated photonic circuits (PICs) have seen an explosion in interest, through to commercialization in the past decade. Most PICs rely on sharp resonances to modulate, steer, and multiplex signals. However, the spectral characteristics of high-quality resonances are highly sensitive to small variations in fabrication and material constants, which limits their applicability. Active tuning mechanisms are commonly employed to account for such deviations, consuming energy and occupying valuable chip real estate. Readily employable, accurate, and highly scalable mechanisms to tailor the modal properties of photonic integrated circuits are urgently required. Here, we present an elegant and powerful solution to achieve this in a scalable manner during the semiconductor fabrication process using existing lithography tools: by exploiting the volume shrinkage exhibited by certain polymers to permanently modulate the waveguide's effective index. This technique enables broadband and lossless tuning with immediate applicability in wide-ranging applications in optical computing, telecommunications, and free-space optics.

Interleaved signal multiplexing readout in depth encoding Prism-PET detectors.

Given the large number of readout pixels in clinical positron emission tomography (PET) scanners, signal multiplexing is an indispensable feature to reduce scanner complexity, power consumption, heat output, andcost. In this paper, we introduce interleaved multiplexing (iMux) scheme that utilizes the characteristic light-sharing pattern of depth-encoding Prism-PET detector modules with single-ended readout. In the iMux readout, four anodes from every other silicon photomultiplier (SiPM) pixels across rows and columns, which overlap with four distinct light guides, are connected to the same application-specific integrated circuit (ASIC) channel. The 4-to-1 coupled Prism-PET detector module was used which consisted of a 16× 16 array of 1.5 × 1.5 × 20 mm3 lutetium yttrium oxyorthosilicate (LYSO) scintillator crystals coupled to an 8 × 8 array with 3× 3mm2 SiPM pixels. A deep learning-based demultiplexing model was investigated to recover the encoded energy signals. Two different experiments were performed with non-multiplexed and multiplexed readouts to evaluate the spatial, depth of interaction (DOI), and timing resolutions of our proposed iMuxscheme. The measured flood histograms, using the decoded energy signals from our deep learning-based demultiplexing architecture, achieved perfect crystal identification of events with negligible decoding error. The average energy, DOI, and timing resolutions were 9.6 ± 1.5%, 2.9 ± 0.9mm, and 266 ± 19ps for non-multiplexed readout and 10.3 ± 1.6%, 2.8 ± 0.8mm, and 311 ± 28ps for multiplexed readout,respectively. Our proposed iMux scheme improves on the already cost-effective and high-resolution Prism-PET detector module and provides 16-to-1 crystal-to-readout multiplexing without appreciable performance degradation. Also, only four SiPM pixels are shorted together in the 8× 8 array to achieve 4-to-1 pixel-to-readout multiplexing, resulting in lower capacitance per multiplexedchannel.

Digital self-interference cancellation for full-duplex systems based on deep learning

Full-duplex (FD) systems can double the spectrum efficiency by allowing users to transmit and receive signals at the same time and in the same frequency band. However, in FD systems the receiver suffers severe self-interference (SI) caused by the transmitter and eliminating the SI is challenging. In this paper, we propose a novel digital self-interference cancellation (SIC) scheme based on deep learning, which combines the power of sliding window, gated recurrent unit (GRU) network and attention mechanism (AM). The proposed scheme can accurately reconstruct the SI through two steps. It first processes the sample signals utilizing the sliding window and then extracts the dependence in preprocessed signals by applying the GRU with AM. We adopt the orthogonal frequency division multiplexing (OFDM) signal as the baseband transmitted signal to verify the proposed scheme. Extensive experiments demonstrate that the SIC capability of the developed scheme is at least 14.46 dB higher than the existing polynomial and neural network (NN) schemes. Furtherly, the effectiveness of the scheme is verified in different interference-to-noise ratio (INR), multipath channel, training sample and OFDM symbol situations.

Integration of Raspberry Pi and antennas for multiplexing digital signals over a fiber optical communication system

A Fiber Optical Communication System (FOCS) is used to experimentally demonstrate the transmission of multi-channel information of two High Definition (HD) video signals and 18 digital TV channels. These signals are supplied using commercial Raspberry Pi boards and digital TV Antennas, respectively. Both digital signals and lightwaves of a couple of Distributed Feedback (DFB) lasers with wavelengths located at 1547.5 and 1552.5 nm interact with two Mach-Zehnder Intensity Modulators (MZ-IM). The resulting modulated optical signals from each modulator are combined by using an optical coupler. The combined optical field is amplified and transmitted through 30 km of single-mode optical fiber. To demultiplex the combined optical signals, a bandpass optical filter is used, then a PIN-photodetector is connected to recover HD video signals and the 18 digital TV channels. The measured electrical spectrum of the received signals shows that the transmission is performed without interference and the multi-channel information is successfully received in an HD display. The use of wavelengths with linewidths of 10 MHz and an optical fiber with a chromatic dispersion of 17 ps/nm-km allows for a maximum bit rate of approximately 11 Gbps to be achieved numerically. This result guarantees that HD video signals can be experimentally transmitted successfully with Bit Error Rate (BER) values between 10-6 and 10-15 when the optical power of lasers is tuned between 7 and 9 dBm.

28 GHz over-the-air measurement using an OTFS multi-user distributed MIMO under Doppler effect

AbstractThis paper describes the experimental investigation of orthogonal time-frequency space (OTFS) modulation using a 28 GHz multi-user distributed multiple-input multiple-output (D-MIMO) testbed in over-the-air (OTA) and mobility environments to enhance cell throughput in a millimeter-wave band. We build the D-MIMO testbed having newly developed OTFS modulator and demodulator, and measured OTFS signals and orthogonal frequency-division multiplexing (OFDM) signals with up to four user simultaneous connections on an actual office floor. Additionally, the Doppler effect on OTFS signals is mathematically analyzed and is confirmed in the measurements. OTFS indicates higher robustness in time-variant channels than OFDM. The error vector magnitude (EVM) and system throughput of OTFS are −22 dB and 1.9 Gbps with 100 MHz signal bandwidth, respectively. To our knowledge, this is a first paper describing the OTA measurements of EVM, throughput, and spectral efficiency using OTFS modulation on the 28 GHz coherent beamforming system.

Constant envelope OFDM transmission over metro-regional optical links

The transmission of constant envelope orthogonal frequency division multiplexing (CE-OFDM) signals is experimentally demonstrated in this paper to increase the reach of metro-regional optical links. A recirculating fiber loop was implemented for this aim. A reach extension of 100 km of standard single-mode fiber was achieved with the CE-OFDM-based system, considering 16 quadrature amplitude modulation (16-QAM) as subcarrier mapping and links without optical dispersion compensation. Link lengths as long as 700 km, with spectral efficiency of 1.89 b/s/Hz, were accomplished with performances below the forward error correction limit.

Ultrawideband RF-IQ Modulator Using Segmented Nonlinearly Scaled RF-DACs and Nonoverlapping LO Signals

A wideband Cartesian in-phase and quadrature (I/Q) modulator based on dual 10 b RF-digital-to-analog converters (DACs) is presented. Nonoverlapping local oscillator (LO) signals and a segmented nonlinear scaling with scaled unit cells contribute to a high linearity and allow for a low-complexity digital predistortion (DPD). Unit-cell flip-flops (FFs) and a balanced clock distribution enable a high sample rate with little skew. Out-of-band emissions are reduced through drive-slope control of the data-switch inputs. The modulator, implemented in the 22-nm fully-depleted silicon-on-insulator (FDSOI) CMOS, operates between 20 and 26 GHz with a peak sample rate of 11 GS/s. It has been used to demonstrate the transmission of a 64-quadrature amplitude modulation (QAM) single-carrier (SC) signal at 13.2 Gb/s, a 256-QAM SC signal at 7.33 Gb/s, and an orthogonal frequency division multiplexing (OFDM) signal comprising four aggregated 400-MHz 64-QAM channels with an error vector magnitude (EVM) of 6.43%. These results demonstrate the potential of the proposed modulator for the realization of ultrawideband transmitters in high-performance millimeter-wave (mmW) systems.

Nonlinear polarization crosstalk canceled wavelength conversion for Pol-Mux OFDM signal with polarization-diversity FWM.

We present a model that is capable of describing the polarization crosstalk in terms of nonlinear polarization rotation (NPR) of semiconductor optical amplifier (SOA) in wavelength conversion for polarization multiplexing (Pol-Mux) orthogonal frequency division multiplexing (OFDM) signal. Then a simple nonlinear polarization crosstalk canceled wavelength conversion (NPCC-WC) with polarization-diversity four-wave mixing (FWM) is proposed. The effectiveness is achieved successfully in the proposed wavelength conversion for the Pol-Mux OFDM signal by using simulation. In addition, we studied the influence of several system parameters on the performance, including the power of the signal, SOA's injection current, frequency spacing, polarization angle of signal, laser linewidth, and modulation order. The results show that the proposed scheme has better performance due to crosstalk cancellation than the conventional scheme, such as wider wavelength tunability, lower polarization sensitivity, and wider laser linewidth tolerance.

Effect of stimulation intensity of a differential target multiplexed SCS program in an animal model of neuropathic pain.

Spinal cord stimulation (SCS) has been proven to be an effective treatment for patients suffering from intractable chronic neuropathic pain. Recent advances in the field include the utilization of programs that multiplex various signals to target different neural structures in the dorsal spinal cord associated with the painful area. Preclinical studies have been fundamental in understanding the mechanism by which this differential target multiplexed programming (DTMP) SCS approach works. Transcriptomic- and proteomic-based studies demonstrated that DTMP can modulate expression levels of genes and proteins involved in pain-related processes that have been affected by a neuropathic pain model. This work studied the effect of the intensity of DTMP signals on mechanical hypersensitivity and cell-specific transcriptomes. The spared nerve injury model (SNI) of neuropathic pain was induced in 20 animals which were 1:1 randomized into two SCS groups in which the intensity of the DTMP was adjusted to either 70% or 40% of the motor threshold (MT). SCS was applied continuously for 48 h via a quadripolar lead implanted in the dorsal epidural space of animals. Controls, which included a group of implanted SNI animals that received no SCS and a group of animals naive to the SNI, were assessed in parallel to the SCS groups. Mechanical hypersensitivity was assessed before SNI, before SCS, and at 48 h of SCS. At the end of SCS, the stimulated segment of the dorsal spinal cord was dissected and subjected to RNA sequencing to quantify expression levels in all experimental groups. Differential effects were assessed via fold-change comparisons of SCS and naive groups versus the no-SCS group for transcriptomes specific to neurons and glial cells. Standard statistical analyses were employed to assess significance of the comparisons (p < 0.05). SCS treatments provided significant improvement in mechanical sensitivity relative to no SCS treatment. However, the change in the intensity did not provide a significant difference in the improvement of mechanical sensitivity. DTMP regulated expression levels back toward those found in the naive group in the cell-specific transcriptomes analyzed. There were no significant differences related to the intensity of the stimulation in terms of the percentage of genes in each transcriptome in which expression levels were reversed toward the naive state. DTMP when applied at either 40% MT or 70% MT provided similar reduction of pain-like behavior in rats and similar effects in neuron- and glia-specific transcriptomes.

Demonstration of High Capacity Bidirectional A-RoF System Using Wavelength Reuse and Frequency Multiplexing

We demonstrate a practical wavelength reuse bidirectional analog radio-over-fiber (A-RoF) system served by a single distributed feedback (DFB) laser. Frequency interleaving of downlink and uplink signals is proposed to ameliorate the spectral efficiency and mitigate the interference raised by the bidirectional transmission. Pre-emphasis is exploited to counteract the performance impairment brought about by the interaction between laser chirp and fiber chromatic dispersion. Through employing 64-QAM modulated 16 bands and 16-QAM modulated 12 bands filtered orthogonal frequency division multiplexing (f-OFDM) signals with 200 MHz bandwidth, asymmetric transmission with superior flexibility over 25 km fiber is attained, with an aggregate capacity of 20 Gb/s for downlink and 10 Gb/s for uplink. The mutual interference between the downlink and uplink is explored by overlapping the downlink and uplink signal spectra to varying degrees. Using the optimum frequency configuration, system performance is evaluated in terms of EVM and phase noise. To further investigate the effects caused by the Rayleigh backscattering and the stimulated Brillouin scattering (SBS), simulations are conducted on the proposed architecture, validating the conclusion from the experiment that the bidirectional transmission is primarily limited by the Rayleigh backscattering than the stimulated Brillouin scattering.

Photonics-Assisted Analog Wideband Self-Interference Cancellation for In-Band Full-Duplex MIMO Systems With Adaptive Digital Amplitude and Delay Pre-Matching

A photonics-assisted analog wideband RF self-interference (SI) cancellation and frequency downconversion approach for in-band full-duplex (IBFD) multiple-input multiple-output (MIMO) systems with adaptive digital amplitude and delay pre-matching is proposed based on a dual-parallel Mach–Zehnder modulator (DP-MZM). In each MIMO receiving antenna, the received signal, including different SI signals from different transmitting antennas and the signal of interest, is applied to one arm of the upper dual-drive Mach–Zehnder modulator (DD-MZM) of the DP-MZM, the reference signal is applied to the other arm of the upper DD-MZM, and the local oscillator signal is applied to one arm of the lower DD-MZM. The SI signals are canceled in the optical domain in the upper DD-MZM and the frequency downconversion is achieved after photodetection. To cancel the SI signals, the analog reference signal is constructed in the digital domain, while the amplitude and delay of the constructed reference are adjusted digitally by upsampling with high accuracy. Experiments are performed when two different SI signals are employed. The genetic algorithm or least squares algorithm is combined with segmented search respectively for the SI signal reconstruction and amplitude and delay pre-matching. A cancellation depth of around 20 dB is achieved for the 1-Gbaud 16 quadrature-amplitude modulation orthogonal frequency-division multiplexing signal.

Fiber-terahertz-fiber bridge system in the 355-GHz band using a simple optical frequency comb and a photonics-enabled receiver.

This Letter demonstrates a high-speed fiber-terahertz-fiber system in the 355-GHz band using stable optical frequency comb generation and a photonics-enabled receiver. At the transmitter, a single dual-drive Mach-Zehnder modulator is employed to generate a frequency comb by driving the modulator under an optimal condition. At the antenna site, a photonics-enabled receiver consisting of an optical local oscillator signal generator, a frequency doubler, and an electronic mixer is used to downconvert the terahertz-wave signal to the microwave band. Simple intensity modulation and a direct detection method are used for transmitting the downconverted signal to the receiver over the second fiber link. To demonstrate the proof of concept, we transmitted a 16-quadrature amplitude modulation (QAM) orthogonal frequency-division multiplexing signal over a system consisting of two radio-over-fiber links and a 4 m wireless link in the 355-GHz band and achieved a line rate of 60 Gb/s. We also successfully transmitted a 16-QAM subcarrier multiplexing single-carrier signal over the system and achieved a capacity of 50 Gb/s. The proposed system can facilitate the deployment of ultra-dense small cells in high-frequency bands in beyond-5G networks.

65,536-QAM OFDM signal transmission over a fiber-THz system at 320 GHz with delta-sigma modulation.

The transmission of a 65,536-ary quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM) signal supported by a hybrid fiber-terahertz (THz) multiple-input multiple-output (MIMO) system at 320 GHz is experimentally demonstrated in this Letter. We adopt the polarization division multiplexing (PDM) technique to double the spectral efficiency. Based on a 23-GBaud 16-QAM link, 2-bit delta-sigma modulation (DSM) quantization enables 65,536-QAM OFDM signal transmission over a 20-km standard single-mode fiber (SSMF) and a 3-m 2 × 2 MIMO wireless delivery, and satisfies the hard-decision forward error correction (HD-FEC) threshold of 3.8 × 10-3, corresponding to a net rate of 60.5 Gbit/s for THz-over-fiber transport. Meanwhile, below the fronthaul error vector magnitude (EVM) threshold of 0.34%, a maximum signal-to-noise ratio (SNR) of 52.6 dB is achieved. To the best of our knowledge, this is the highest modulation order achievable for DSM applications in THz communication.

Single-Input Broadband Hybrid Doherty Power Amplifiers Design Relying on a Phase Sliding-Mode of the Load Modulation Scheme

This work introduces a novel design theory for a single-input hybrid Doherty power amplifier (PA) inspired by the design space existing within the previously reported dual-input Doherty–Chireix (outphasing) continuum. Unlike the conventional <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\lambda /4$ </tex-math></inline-formula> Doherty PA inverter which only performs the correct load modulation at its center frequency, the hybrid Doherty PA (HD <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\omega $ </tex-math></inline-formula> -PA) combiner network achieves a wideband load modulation using the frequency dependence of the electrical length of the output combiner lines versus frequency for sliding the PA mode of operation. A modified theory is presented in this work to allow for a single-input PA implementation. In this new design, the outphasing angle is only changing with frequency and not the input power. A transmission line phase shifter is used to provide the correct frequency-dependent input phase offset ensuring the correct wideband load modulation performed by the output combiner. A novel methodology is also proposed to select the optimal input phase offset to reduce the variation in the saturation power versus frequency and minimize the circuit size. A proof-of-concept demonstrator PA circuit is designed to operate from 2.5 to 3.3 GHz. When the fabricated PA is excited by a 20-MHz long-term evolution (LTE) modulated signal with 6-dB peak-to-average-power ratio (PAPR), an average efficiency of 45%–59% and adjacent channel leakage ratio (ACLR) less than −50 dBc are achieved after digital predistortion (DPD) across the entire band. When the fabricated PA is excited by a 5G-like 50-MHz orthogonal frequency-division multiplexing (OFDM) signal with 10-dB PAPR, an average efficiency of 33%–41% and ACLR less than −44 dBc are achieved after DPD across the entire band.