Molar Mass Research Articles

Parametric analysis of working fluid selection for closed-cycle turbo-refrigerators for deep freezing applications

Working fluid selection for closed-cycle turbo-refrigerators (CCTRs) for deep freezing, as a more fundamental topic, has not yet received careful consideration, leading to limitations in attempts to optimizing CCTR design in the early stages of cycle design. This paper proposed the working fluid selection criteria that to select the one leading to the lowest system weight and volume without compromising the system energy efficiency. Design criteria, such as specific speed and Reynolds number, and their dependence on fluid properties are introduced to ensure uncompromising-efficiency design of turbomachinery. Normalized heat transfer area of recuperator correlated with fluid properties is derived as the evaluation criterion for system weight and volume. Applying the proposed criteria, the comparison between potential pure gases shows the normalized heat transfer areas required for nitrogen, neon, and argon are 1, 1.54 and 2.18, respectively. Therefore, nitrogen among all pure gases has the greatest potential to reduce system weight and volume. The comparison among potential binary mixtures highlights the methane-nitrogen mixture with the molar mass of 24.1 g/mol which reduces the required heat transfer area by approximately 20 % compared to pure-nitrogen-based system and may reduce it by nearly up to 30 % for systems with larger cooling capacity levels.

Tailoring the mechanical and rheological properties of poly(lactic acid) by sterilizing UV-C irradiation

In this study, we irradiated amorphous (A) and semi-crystalline (SC) poly(lactic acid) (PLA) with different UV-C doses up to 2214 kJ/m2. We achieved an average crystallinity of 43 % by heat treatment, which was unaffected by UV-C irradiation. Modulated differential scanning calorimetry showed that crystal polymorphs and the ratio of rigid amorphous and mobile amorphous phases were also unaffected. Using gel permeation chromatography analysis, we showed that the degradation mechanism was noncatalytic random scission, and the initial molar mass was reduced by >90 % at a dose of 2214 kJ/m2 for both A- and SC-PLA samples. Our Raman spectroscopy results indicated that the probability of the formation of oxygen-containing groups increases with increasing UV-C doses. Since we found that the mechanical properties of PLA films can be tailored with UV-C light, we proposed a method to predict the overall tensile curve as a function of the UV-C dose. We also proposed a modified Cross-WLF model to describe the effect of UV-C irradiation on viscosity up to 55 % molar mass reduction. The models allow us to estimate the limits of recyclability and reusability of sterilised PLA products.

Poly(2-alkyl/aryl-2-oxazoline)-Imidazole Complexes as Thermal Latent Curing Agents for Epoxy Resins.

One-component epoxy resins (OCERs) with improved stability (shelf life) and controlled curing temperatures were prepared using epoxy resins and polyoxazoline-imidazole (POZ-Im) based thermal latent curing agents (TLCs). POZ homopolymers with molar masses of 1000, 2000, and 5000 g/mol were obtained via cationic ring-opening polymerization (CROP) of 2-ethyl-2-oxazoline, 2-propyl-2-oxazoline, 2-pentyl-2-oxazoline, and 2-phenyl-2-oxazoline. TLCs were prepared by physically entrapping imidazole, the curing agent, in the POZ matrix at the homopolymer/Im (HP/Im) ratios of 1:1 and 5:1 and characterized by FTIR and TGA. TLCs were then mixed with bisphenol A diglycidyl ether (DGEBA) to obtain OCERs with Im concentrations of 1, 3, and 5 wt %. Dynamic DSC tests were performed to determine the effect of the pendant group and molar mass of POZ, the POZ/Im ratio, and Im concentration on the curing behavior of the OCERs, whereas isothermal DSC tests were carried out to examine their thermal stability and optimal curing temperatures. Optical microscopy was performed to study the compatibility of the TLCs with DGEBA. This study showed that the dispersion quality of TLCs is highly associated with the compatibility of POZs and DGEBA, which affected the release of Im, thus left limit temperatures of curing. In addition, higher left limit temperatures were obtained when the POZ/Im ratio increased. Isothermal DSC results conformed to the improved stability and better thermal latency of the samples with a POZ/Im ratio of 5:1. Moreover, the higher left limit temperatures were obtained with the lowest molar mass of POZ due to the better interaction between the -OH end group of POZ and Im. The shelf life of PEOZ 1K-Im 5:1 1% OCER was predicted at -20, 0, and 20 °C, with an estimated 15.3 days at 20 °C using isothermal DSC and rheology at 50, 60, and 70 °C. Overall, this research contributes to the development of OCERs by introducing POZ-Im complexes as novel TLCs. The findings shed light on the importance of compatibility in achieving optimal dispersion and release of Im and the role of the POZ/Im ratio and POZ molar mass in controlling left limit temperatures, ultimately influencing the curing behavior of OCERs.

Reducing Solvent Consumption in Reductive Catalytic Fractionation through Lignin Oil Recycling.

Reductive catalytic fractionation (RCF) enables the simultaneous valorization of lignin and carbohydrates in lignocellulosic biomass through solvent-based lignin extraction, followed by depolymerization and catalytic stabilization of the extracted lignin. Process modeling has shown that the use of exogenous organic solvent in RCF is a challenge for economic and environmental feasibility, and previous works proposed that lignin oil, a mixture of lignin-derived monomers and oligomers produced by RCF, can be used as a cosolvent in RCF. Here, we further explore the potential of RCF solvent recycling with lignin oil, extending the feasible lignin oil concentration in the solvent to 100 wt %, relative to the previously demonstrated 0-19 wt % range. Solvents containing up to 80 wt % lignin oil exhibited 83-93% delignification, comparable to 83% delignification with a methanol-water mixture, and notably, using lignin oil solely as a solvent achieved 67% delignification in the absence of water. In additional experiments, applying the RCF solvent recycling approach to ten consecutive RCF reactions resulted in a final lignin oil concentration of 11 wt %, without detrimental impacts on lignin extraction, lignin oil molar mass distribution, aromatic monomer selectivity, and cellulose retention. Overall, this work further demonstrates the potential for using lignin oil as an effective cosolvent in RCF, which can reduce the burden on downstream solvent recovery.

Identifying the location and micellization of PEG-b-PCL multiblock copolymers in PLA/PCL blends via AFM nanoscale IR spectroscopy

The IR absorption mapping of two multiblock copolymers based on poly(ethylene glycol) and poly(ε-caprolactone) segments (PEG-b-PCL) in poly(acid lactic) and poly(ε-caprolactone) blends (PLA/PCL) was performed via AFM nanoscale IR spectroscopy. These copolymers, having the same number average molar masses (Mn‾) but varying block sizes, were added into the blend in different amounts (1 and 5 wt%) using a co-rotating twin-screw extrusion. The results revealed that copolymers with smaller blocks are preferentially located near the interface when incorporated in small quantities. Increasing the copolymer content led to preferential diffusion into the PLA matrix. Compatibilization with the longer block-size copolymers also led to preferential diffusion in the PLA matrix, albeit with a tendency to form micelles. This hampers the overall mechanical properties of the blend, making the compatibilized blend more brittle than neat PLA. Compatibilization with the short block-size copolymers showed no micellization and improved the mechanical behavior of PLA/PCL.

Monothiolactide, a New Monomer for the Synthesis of Recyclable, Alternating Ester-Thioester Polymers.

Aliphatic polyesters and polythioesters are very interesting alternatives for current fossil-based and degradation-resistant plastics, due to their high (bio)degradability and (chemical) recyclability potential. Two important examples include polylactide (PLD), currently leading the synthetic bioplastics market, and its sulfur analog polythiolactide (PTLD). Both polymers can be made by ring-opening polymerization (ROP) of their corresponding (thio)dilactones, lactide (LD) and thiolactide (TLD) respectively. In this work, the benefits of esters and thioesters were combined in one material by the successful catalytic synthesis and ROP of monothiolactide (MTL), an unprecedented monomer containing half a LD and half a TLD structural unit. MTL can be obtained by a simple direct condensation of biobased lactic acid and thiolactic acid aided by Brønsted acid catalysis. The novel, but simple monomer showed to be easily polymerized with triethylamine to materials containing alternating lactic and thiolactic ester units with a very high molar mass. The lower stability of MTL (vs. TLD) resulted in improved ROP thermodynamics, while also fast and controllable polymerization kinetics were observed. The new polymers feature a good chemical recycling and hydrolytic degradation potential with important improvements compared to PTLD and PLD. Finally, a successful co-polymerization with commercial LD was shown, paving the way towards industrialization.

Sequence of Monomers and Position of Stereocenters Matter for Thermal Properties of Stereocontrolled Oligourethanes.

Polyurethanes are commodity materials used for multiple applications. In recent years, a new category of polyurethane material has emerged, characterized by the lack of polymer molar mass dispersity, control of the monomer arrangement in the chain, and even full stereocontrol. Various multistep synthesis strategies have been developed to fabricate sequence-defined polyurethanes. However, synthesizing stereocontrolled polyurethanes with a controlled sequence is still a challenge. Polyurethanes with structural precision, as represented by biopolymers, i. e. proteins or nucleic acids, have opened new application directions for these groups of materials. It has been shown that polyurethanes can be used as biomimetics, information carriers, molecular tags, and materials with strictly controlled properties. Precise synthesis of macromolecules allows us to fine-tune the properties of polymers to specific needs. Therefore, it is essential to collect information on the sequence-structure relationship of polymers. In our work, we present synthetic pathways to make sequence and stereo-defined oligourethanes. We demonstrate that structural details, i. e., the monomer sequences and position of the stereocenter, have a tremendous effect on the thermal properties of model oligourethanes. We show that the introduction of chirality by constitutional isomerization can be used to program the thermal characteristics of polymers, which are key features for material applications.

Effect of the molar mass of chitosan and film casting solvents on the properties of chitosan films loaded with Mentha spicata essential oil for potential application as wound dressing

Chitosan based films endowed with antibacterial features have witnessed remarkable progress as potential wound dressings. The current study aimed at appraising the effects of the molar mass of chitosan (MM) and the film casting acids on the properties of unplasticized chitosan films and plasticized MSO-embedded chitosan films in order to provide best suited film formulation as a potential candidate for wound dressing application. The prepared films were functionally characterized in terms of their qualitative assessment, thickness, density, swelling behavior, water vapor barrier, mechanical and antibacterial properties. Overall, all chitosan films displayed thickness lower than the human dermis even though thicker and denser films were produced with lactic acid. Assessment of the swelling behavior revealed that only high molar mass (HMM) chitosan films may be regarded as absorbent dressings. Moreover, unplasticized HMM lactate (HMM-LA) films furnished lower stiffness and higher percent strain break as compared to acetate films, due to the plasticizing effect of the remaining lactic acid as alluded by the FTIR analysis. Meanwhile, they provided suitable level of moisture and indicated substantial antibacterial activity against S. aureus and E. coli, the most commonly opportunistic bacteria found in infected skin wound. Plasticized chitosan films doped with MSO were significantly thicker and more permeable to water compared to unplasticized films. Furthermore, MSO significantly potentiate the antibacterial effect of chitosan-based films. Therefore, plasticized HMM-LA/MSO chitosan film flashing good swelling behavior, adequate WVTR and WVP, suitable mechanical properties and antibacterial performances substantiated to be a promising antibacterial dressing material for moderately exuding wounds.

The Influence of Arabinoxylan of Different Molar Masses on the Properties of Rye Bread Baked by the Postponed Baking Method.

Rye grain is a good source of dietary fiber, phenolic compounds, vitamins, and mineral compounds. To prevent the staling process of bread, semi-finished bakery products are subjected to cooling or freezing, and this process is called the postponed baking method. The aim of this study was to examine the influence of rye arabinoxylans differing in molar mass on the properties of rye bread baked using the postponed baking method. The breads were baked from rye flour types 720 and 1150, without and with a 1% share of unmodified or cross-linked rye arabinoxylans (AXs). The molar mass of the unmodified AXs was 432,160 g/mol, while that of the AXs after cross-linking was 1,158,980 g/mol. The results of this study show that the 1% share of AXs significantly increased the water addition to both types of rye flour and dough yield, and this increase was proportional to the molar mass of the AXs used. It is shown that a 1% share of both AX preparations positively increased the volume and crumb moisture of bread baked by the postponed baking method. Cross-linked AXs proved to be particularly effective in increasing the volume and bread crumb moisture. Both AX preparations had a positive effect on reducing the bread crumb hardness of rye breads baked by the postponed baking method.

Potential of Benchtop NMR for the Determination of Polymer Molar Masses, Molar Mass Distributions, and Chemical Composition Profiles by Means of Diffusion-Ordered Spectroscopy, DOSY.

The determination of molar masses and their distributions is crucial in polymer synthesis and design. This work presents the current performance and limitations of diffusion-ordered spectroscopy (DOSY) on a low-field (benchtop) NMR spectrometer (at 90MHz) as an alternative to size exclusion chromatography (SEC) for determining diffusion coefficient distributions (DCDs) and molar mass distributions (MMDs). After optimization for narrowly distributed homopolymers, MMDs obtained with inverse Laplace transformation (ILT) and log-normal distribution are compared with average molar masses obtained with mono- and bi-exponential fits, as well as MMDs obtained from SEC. This approach enables ILT to determine DCDs and MMDs even for bimodal homopolymers with fully spectrally overlapping signals and block copolymers with various chemical compositions, for which chemical composition profiles are determined. The feasibility of low-field diffusion NMR with samples dissolved in non-deuterated solvents is further demonstrated and methods for solvent suppression are discussed.

Surface Tension of Simple Molten Salts: Insight from a Charged Hard Sphere Model.

Surface tension of molten salts is rooted in many important phenomena in physical chemistry. We develop an analytical theory for the surface tension of molten salts, where the molten salt is described by a restricted primitive model electrolyte consisting of charged hard spheres, and surface tension is related to the formation of a cavity in the electrolyte. The integral equation theory is applied to the restricted primitive model electrolyte to derive an analytical formula of the cavity formation energy. The scaling relation of the cavity formation energy is further combined with morphological thermodynamics theory to determine the formula for surface tension. According to our formula, surface tension consists of a positive hard sphere contribution and a negative electrostatic contribution. Using the molar mass, interionic distance, density, and temperature as the input, our theory leads to a good prediction of surface tension of more than 16 molten salts at their melting point without introducing any adjustable parameters.

TFE Terpolymers: Once Promising - Are There Still Perspectives in the 21st Century: Synthesis, Characterization, and Properties-Part I.

Polytetrafluoroethylene (PTFE) exhibits outstanding properties such as high-temperature stability, low surface tension, and chemical resistance against most solvents, strong acids, and bases. However, these traits make it challenging to subject PTFE to standard polymer processing procedures, such as thermoforming and hot incremental forming. While polymer processing at temperatures above the melting point of PTFE is already demanding, the typically large molar mass of PTFE results in extremely high melt viscosities, complicating the processing of PTFE. Also, PTFE tends to decompose at temperatures close to its melting point. Therefore, fluoropolymers obtained by copolymerizing tetrafluoroethylene (TFE) with various co-monomers are studied as alternatives to PTFE (e.g., fluorinated ethylene-propylene (FEP)), combining its advantages with better processability. TFE terpolymers have emerged as desirable PTFE alternatives. This review provides an overview of the synthesis with various comonomers and microstructural analysis of PTFE terpolymers and the relationships between the microstructures of TFE terpolymers and their properties.

Green Electrospinning of Highly Concentrated Polyurethane Suspensions in Water: From the Rheology to the Fiber Morphology

AbstractSuspension electrospinning allows the environmental‐friendly fabrication of nano‐micro‐fibrous membranes since it is based on the processing of an aqueous particle suspension in which a hydrosoluble template polymer is added to insure the formation of a continuous fiber. Here, the case of polyurethane (PU) aqueous suspensions formulated with poly(ethylene oxide) (PEO) as the template polymer is studied. The effect of several parameters (particle size, PU/PEO ratio, PEO molar mass, and PEO concentration in the continuous phase) on particle‐particle and particle‐template polymer interactions that influence the rheological properties of the formulation and finally the electrospinning and the fiber morphology, is studied. The goal is to process a formulation with the highest particle content as possible. Thanks to a deep rheological investigation and the study of interactions and suspension morphology by zeta potential and diffusing wave spectroscopy, it is shown that regular fibers are efficiently produced when small particles are electrospun under favorable particle‐template polymer interactions and without screening the electrostatic repulsion between particles. Finally, a fibrous membrane is obtained from a formulation with a PU/PEO weight ratio equal to 50 under very stable and efficient production conditions.

Photochemical [2 + 2] Cycloaddition Enables the Synthesis of Highly Thermally Stable and Acid/Base-Resistant Polyesters from a Nonpolymerizable α,β-Conjugated Valerolactone.

We report a simple strategy to transform a nonpolymerizable six-membered α,β-conjugated lactone, 5,6-dihydro-2H-pyran-2-one (DPO), into polymerizable bicyclic lactones via photochemical [2 + 2] cycloaddition. Two bicyclic lactones, M1 and M2, were obtained by the photochemical [2 + 2] cycloaddition of tetramethylethylene and DPO. Ring-opening polymerization (ROP) of M1 and M2 catalyzed by diphenyl phosphate (DPP), La[N(SiMe3)2]3, and 1-tert-butyl-4,4,4-tris(dimethylamino)-2,2-bis[tris (dimethylamino) phosphoranylide-namino]-2λ5, 4λ5-catenadi(phosphazene) (tBu-P4) were conducted. M1 is highly polymerizable, either DPP or La[N(SiMe3)2]3 could catalyze its living ROP under mild conditions, affording the well-defined PM1 with a predictable molar mass and low dispersity. M2 could only be polymerized with tBu-P4 as the catalyst, also generating the same polymer PM1. PM1 has high thermal stability, with a Td,5% being up to 376 °C. Ring-opening copolymerization (ROcP) of M1 and δ-valerolactone (δ-VL) catalyzed by La[N(SiMe3)2]3 afforded a series of random copolymers with enhanced thermal stabilities. Both PM1 and the copolymer containing 10 mol % M1 exhibited excellent resistance to acidic and basic hydrolysis. Our results demonstrate that direct photochemical [2 + 2] cycloaddition of α,β-conjugated valerolactone is not only a strategy to tune its polymerizability, but also allows for the synthesis of highly thermally stable aliphatic polyesters, inaccessible by other methods.

Oat Beta-Glucan Dietary Intervention on Antioxidant Defense Parameters, Inflammatory Response and Angiotensin Signaling in the Testes of Rats with TNBS-Induced Colitis.

Male infertility represents a significant public health concern. There is a negative impact of inflammatory bowel diseases (IBDs) on the male reproductive system. The aim of this study was to investigate whether oat beta-glucan (OBG) with different molar mass can modulate parameters of antioxidant defense and inflammatory response in the testes of adult Sprague-Dawley rats with TNBS-induced colitis and whether the OBG intervention can modulate the inflammatory response in association with the RAS system. Results: higher testicular superoxide dismutase (SOD), glutathione reductase (GR) activities and glutathione (GSH) concentration, and lower testosterone (T) level and glutathione peroxidase (GPx) activity, were observed in rats with colitis than in healthy control ones. TNBS-induced colitis resulted in decreased the angiotensin 1-7 (ANG 1-7) level in the testes of rats fed with low-molar mass OBG compared to control animals. Conclusions: although colitis induced moderate pro-oxidant changes in the gonads, it seems plausible that dietary intervention with different fractions of oat beta-glucans mass may support the maintenance of reproductive homeostasis via the stimulation of the local antioxidant defense system.

Tenebrio Molitor breeding rejects as a high source of pure chitin and chitosan: Role of the processes, influence of the life cycle stages and comparison with Hermetia illucens

This work valorizes rejects from Tenebrio Molitor TM breeding through the production of chitin and chitosan. Two processes are proposed for extracting chitin from larval exuviae and adult. The first process P1 provides chitin with high contents compared to literature data but the characterization shows the presence of impurities in the exuviae chitin responsible for the shifts in the values of the physicochemical characteristics towards those presented by γ chitin. These impurities are removed by delipidation and pure α chitin is obtained. The effective delipidation of this chitin would be linked to its fibrous surface structure. The analysis of the results of P1 led us to develop a second extraction process P2 which provides pure chitin with improved yields using delipidation followed by deproteinization. The N-deacetylation of chitin according to Kurita or Broussignac process makes possible the preparation of pure, highly deacetylated chitosan samples (2 % < DA < 12 %) with high yields and controlled molar masses (Mv). A kinetic study of molecular degradation during deacetylation is carried out. A comparison with Hermetia illucens allows to extend the use of insects as a potential source of chitin and chitosan and confirms the role of the source and the processes in the determination of their characteristics.

A Closer Look at the Common Molar Mass Experiment

A Closer Look at the Common Molar Mass Experiment

Experimental teaching reform of polymer molar mass determination using gel permeation chromatography coupled with light scattering

Gel permeation chromatography coupled with light scattering (GPC-LS) is among the most common methods for determining the molar masses of polymers. GPC-LS is widely used in polymer science research and has been adopted for many industrial applications owing to its high sensitivity, accuracy, and precision. The determination of polymer molar masses using GPC-LS is an important experimental component of the "Polymer Physics Experiments" course. However, the present GPC-LS experimental teaching content tends to be overly simplistic and lacking in depth. Herein, the original experimental content is expanded and multiple sets of experiments are redesigned: (1) Using commercial polystyrene as an experimental sample, the molar mass, molar mass distribution, radius of gyration, and other molecular structure parameters are determined using GPC-LS; (2) Using two polyacrylonitriles with similar molecular structure parameters, subtle differences in the molar mass distributions of the samples are explored using differential mass distribution curves; (3) By comparing the chromatograms of a series of polyethylene glycols with different molar masses, the effect of molar mass on chromatographic peaks is investigated; and (4) For three different polymers (polyacrylonitrile, poly(methyl methacrylate), and poly(β-cyclodextrin)), the polymer chain conformations are analyzed using conformation plots (i.e., radius of gyration vs. molar mass). In addition, the experimental teaching method is modified to convert passive learning into active learning, thereby improving the students' self-directed learning ability. This experimental teaching reform will help students obtain a more comprehensive understanding of GPC-LS principles and applications, stimulate their enthusiasm for learning, and improve the teaching quality of the experimental course.

Development of a comprehensive normal-phase liquid chromatography × size-exclusion chromatography platform with ultraviolet spectroscopy and high-resolution mass spectrometry detection for the chemical characterization of complex polyesters

BackgroundPolyesters are applied in high-end products in many industrial applications, including resins and powder-coating applications. The characterization of the chemical heterogeneities within a polyester is of utmost interest to develop new products or improve existing applications. Unfortunately, characterization is a difficult task, as polyesters may feature distributions in end-group functionality, molecular weight, chemical composition, and degree of branching. Currently, no analytical method can characterize all these interdependent distributions in a single analysis. ResultsWe report the use of comprehensive normal-phase liquid chromatography × size-exclusion chromatography hyphenated with ultraviolet-light spectroscopy and high-resolution mass spectrometry in parallel (NPLC × SEC–UV/HRMS) to characterize polyesters according to their end-group-functionality and molecular-weight distributions. The chemical composition can be measured with HRMS, while relative quantitation can be performed with UV detection. A supercharging agent was used during ionization allowing to extend the molecular-weight range of the detected chemical species. SignificanceThe presented platform allows characterization of polyesters with varying fractions of carboxyl or hydroxyl end-group functionalities and varying distributions of molecular weight, degree of branching, and chemical compositions. The number-average and weight-average molar masses are obtained in the same analysis. This information cannot be obtained by any one-dimensional technique. The developed NPLC × SEC–UV/HRMS platform is a valuable tool for characterizing polyesters in an industrial setting.

Fractionation and Characterization of Commercial Low Acyl Gellan Gum

AbstractCommercial low acyl gellan (LAG) is purified by the fractional dissolution method. An aqueous solution of purified commercial LAG exhibits polyelectrolyte character due to its high molar mass and carboxylic groups in glucuronic acid fragments. The empirical Fuoss equation determines the intrinsic viscosity of purified LAG in salt‐less water. Fractionation of commercial LAG is carried out by ultrasound treatment. LAG fractions are characterized by 1H NMR and FTIR spectroscopy. The intrinsic viscosities of ultrasonically treated LAG samples are measured in 0.025 m of tetramethylammonium chloride (TMACl). The molecular weights of LAG fractions are determined by the Mark–Kuhn–Houwink equation.