Modeling Of Transport Processes Research Articles

Three-dimensional modeling of flow-sediment transport and large-scale bank erosion process in the Lower Yangtze River

Bank erosion in the Lower Yangtze River (LYR) develops rapidly within a few hours, resulting in a large-scale embayment. A three-dimensional model is proposed in the current research to simulate the development of such an erosion process, coupling a hydro- and sediment dynamic module with a bank erosion module, and is evaluated against the observations in a laboratory experiment and against the measurements in LYR. Analysis of the model results indicates that: ① the model reproduced the overall expansion process of the erosion embayment and demonstrated the essential role of changing flow structure; ②the calculated local flow structure within the embayment consists of a major planar circulation and several minor planar circulations, and the major circulation is the primary driving force for the embayment expansion, while these minor circulations probably contribute to the cease of bank erosion; ③Varying water level in the LYR accelerates the bank erosion process in the study reach, compared with a constant water level.

Inverse Design of Porous Electrodes in Redox Flow Batteries: A Computational Approach Integrating Topology Optimization and Multi-Physics Modeling

The increasing effects of global climate change urge a global energy transition, in which large-scale storage of renewable energy technologies is expected to play a primary role. Redox flow batteries (RFBs) have emerged as a promising technology for grid-scale energy storage with appealing features such as higher durability and power-energy decoupling. During the RFB operation, the liquid electrolytes, stored in external tanks, are actively circulated through the electrochemical stack consisting of flow fields, porous electrodes, and membranes, where electrochemical reactions take place on the surface of the porous electrodes, which are performance-defining components [1]. Despite its advantages, RFB technology has seen limited adoption due to economic and technical challenges. Aiming to boost cost-effectiveness, one effective strategy is to increase the stack power density by increasing the efficiency of the electrodes leading to an increase in the overall system performance [2]. Optimizing reactor performance is challenging due to seemingly contradictory requirements such as providing high surface area for reactions, reducing ohmic drop across the cell, facilitating mass transport in porous media, and reducing pumping power requirements.Parallel to experimental research, computational techniques have the potential to accelerate and guide the design of porous electrodes. An emerging approach in this regard is to use predictive design algorithms that invert the design process and enable the exploration of a broader design space. Topology optimization (TO) is a powerful inverse design technique combining numerical simulations with mathematical optimization algorithms, which involves setting a performance target of minimizing the pumping power and overpotential losses and iterating mathematically over various electrode structures to satisfy the target [3, 4]. This approach requires integrating two different types of models: 1) multi-physics models to build a theoretical framework to adequately relate the local electrode properties to the overall RFB performance, and 2) TO models to inversely design microarchitected variable porosity 3D porous electrodes.In this research, we have developed a high-performance TO framework for three-dimensional porous electrodes in next-generation RFBs integrated with multi-physics computational models of mass, momentum, and charge transport processes using the porous electrode theory, in which the electrode was considered as a macroscopic porosity-variable block. The model was developed using finite element/volume methods implemented using the open-source codes Firedrake, OpenFOAM, and PETSc. The macroscale TO problem was formulated to maximize electrochemical performance under a controllable pumping power loss in a half-cell redox flow cell. The resulting designs were transformed into cellular architectures using triply periodic minimal surface (TPMS) structures and additively manufactured using stereolithography 3D printing followed by carbonization, the output of which can be used to assess the performance of the inversely designed electrodes in a real setup.In this presentation, I will first discuss the structure of the multi-physics modeling approach. Second, I will present the integration of these models into the TO algorithms. Finally, I will show the transformation of the TO results into cellular infills and will highlight some technical aspects of the manufactured TPMS structures.

Structure-Property Relationships for Thin-Ilm Nafion: Model-Predictive Design of Low-Pt PEMFC Catalyst Layers

Proton exchange membrane fuel cells (PEMFCs) are a promising means to decarbonize the global vehicle fleet, but commercialization is limited by costly Pt catalysts, among other challenges. PEMFC designs with low Pt loading typically suffer anomalous performance losses. Previous studies have agreed that poor performance with low Pt-loading is attributed to slow transport through the nano-thin Nafion ionomer found in the catalyst layer (CL). Although it is known that the properties of the Nafion thin films in the CL vary from those previously measured for thicker membranes, research has not yet definitively connected CL polymer properties with PEMFC limitations in low Pt-loaded cells, nor found a means to address the limitations for low cost, higher-performance PEMFCs.This presentation covers parallel efforts to identify and address limiting processes in low-Pt-loaded PEMFC cathode CLs. We begin with an extensive investigation of thin-film Nafion structure-property relationships, as an analog for CL Nafion thin-films. We model nm-scale transport in thin-film Nafion to develop structure-property relationships for thin-film Nafion, based on in situ neutron reflectometry [2], and conductivity measurements [3] on thin film Nafion. These include equilibrium measurements for varying thicknesses and substrates, as well as novel in operando measurements of thin-film Nafion with an H2O flux across the film. Results suggest that conductivity in CL Nafion is a function of not just temperature and relative humidity (as in bulk Nafion membranes), but also film thickness and proximity to the substrate. These insights result in a model that calculates the conductivity as a function of temperature, local water uptake, film thickness, and underlying substrate (Pt or carbon).Simultaneously, we have conducted continuum-scale numerical simulations of PEMFC catalyst layers, to determine the necessary level of detail for predictive yet efficient numerical simulation for device design. Incorporating these structure-property models into a continuum-scale PEMFC cathode half-cell model to locally resolve proton conductivity and O2 diffusion improves model fits to PEMFC data with varying Pt loading [4]. The fits provide new insights into the coupling between kinetic, mass transport, and Ohmic losses in low-Pt-loaded PEMFC cathodes and show that ohmic losses related to proton transport in thin film Nafion play a key role in low-Pt loaded cells. Based on these new fits to low-Pt loaded cells, we present a parametric study of PEMFC CL design parameters with low Pt loading. Incorporating multi-scale modeling of Nafion transport processes enhances the predictive model capabilities and unlocks new insights into CL design. In particular, results suggest that functionally graded catalyst layer designs could significantly improve PEMFC power density with low Pt loading [4]. Weber, A. and Kusoglu, A. Mater. Chem. A. 2014. DOI: 10.1039/c4ta02952fDeCaluwe, S.C. et al. Nano Energy 2018.DOI: 10.1016/j.nanoen.2018.01.008Paul, D.K. et al. Electrochem. Soc. 2014. DOI: 10.1149/2.0571414jesRandall, C.R. and DeCaluwe, S.C., Electrochem. Soc. 2022. DOI: 10.1149/1945-7111/ac8cb4

Modeling of non-equilibrium suspended sediment transport process in open channel flows with vegetation

A mathematical model based on advection-diffusion theory is established to study the non-equilibrium sediment transport process in vegetated channels. The effects of vegetation on velocity distribution and sediment diffusion coefficients were considered, respectively. Validation against experimental data from flume studies confirms the model's ability to accurately predict the longitudinal sediment deposition rate and the vertical distribution of suspended sediment concentration (SSC). A comparative analysis of three sediment diffusion coefficient formulations indicates that the linear-exponential formula provides a more precise estimate of εsz, and the linear-exponential formula performs well in predicting the turbulent diffusion coefficients of both rigid and flexible vegetation when gently swaying. Moreover, the distance required for SSC to regain equilibrium is influenced by the submergence level of the vegetation canopy. At lower submergence levels, the canopy shear vortices significantly affect the vertical exchange of sediment, and the sediment diffusion coefficients exhibit pronounced stratification near the vegetation canopy. An increase in vegetation density at these lower submergence levels intensifies the shear vortices, thereby extending the distance needed for SSC to reach equilibrium. At higher submergence levels, the impact of canopy shear vortices is lessened, which reduces sediment diffusion coefficient stratification characteristics, and the flow is similar to rough boundary layer flow. An increase in vegetation density increases flow resistance, which shortens the distance required for SSC to attain equilibrium. However, further efforts are required to explore turbulent characteristics with highly flexible vegetation motion and the grain size distribution of non-uniform sediments in vegetated flows.

Variations in plume activity reveal the dynamics of water-filled faults on Enceladus

After discovering a jet activity near the south pole of Saturn’s moon Enceladus, the Cassini mission demonstrated the existence of a subsurface water ocean with a unique sampling opportunity through flybys. Diurnal variations in the observed brightness of the plume suggest a tidal control, although the existence and timing of two activity maxima seem to contradict stress analysis predictions. Here, we re-interpret the observed plume variability by combining a 3D global model of tidal deformation of the fractured ice shell with a 1D local model of transport processes within south-polar faults. Our model successfully predicts the observed plume’s temporal variability by combining two independent vapour transport mechanisms: slip-controlled jet flow and normal-stress-controlled ambient flow. Moreover, it provides a possible explanation for the differences between the vapour and solid emission rates during the diurnal cycle and the observed fractionation of the various icy particle families. Our model prediction could be tested by future JWST observations targeted when Enceladus is at different positions on its orbit and could be used to determine the optimal strategy for plume material sampling by future space missions.

Modeling of plasma facing component erosion, impurity migration, dust transport and melting processes at JET-ILW

An overview of the modeling approaches, validation methods and recent main results of analysis and modeling activities related to the plasma-surface interaction (PSI) in JET-ILW experiments, including the recent H/D/T campaigns, is presented in this paper. Code applications to JET experiments improve general erosion/migration/retention prediction capabilities as well as various physics extensions, for instance a treatment of dust particles transport and a detailed description of melting and splashing of PFC induced by transient events at JET. 2D plasma edge transport codes like the SOLPS-ITER code as well as PSI codes are key to realistic description of relevant physical processes in power and particle exhaust. Validation of the PSI and edge transport models across JET experiments considering various effects (isotope effects, first wall geometry, including detailed 3D shaping of plasma-facing components, self-sputtering, thermo-forces, physical and chemically assisted physical sputtering formation of W and Be hydrides) is very important for predictive simulations of W and Be erosion and migration in ITER as well as for increasing quantitative credibility of the models. JET also presents a perfect test-bed for the investigation and modeling of melt material dynamics and its splashing and droplet ejection mechanisms. We attribute the second group of processes rather to transient events as for the steady state and, thus, treat those as independent additions outside the interplay with the first group.

(Invited) Engineering Porous Electrodes for Redox Flow Batteries – Leveraging Computational and Synthetic Platforms

Porous electrodes are critical components in redox flow batteries where they are responsible for multiple critical functions in the cell, such as providing surfaces for electrochemical reactions, an open structure for fluid flow and mass transport, and the conductive scaffold for electronic and thermal conduction. However, our current portfolio of materials is limited to carbon-fiber-based electrodes which are assembled using various mechanical methods (e.g., paper making, weaving, hydro-entangling) resulting in distinct structures such as papers, cloths, and felts (1). These fabrication methods involve multiple complex subprocessing steps impacting the final product cost and limiting the achievable range of electrode properties, which ultimately restricts device performance (2). Thus, there is a need to develop new material sets with precise control over microstructure and surface composition while employing synthetic methods that are compatible with large-scale manufacturing.In this lecture, I will discuss our efforts to design tailored electrodes for redox flow batteries, which hold promise for long-duration stationary energy storage (3). First, I will introduce a pore network modeling framework that captures electrochemical performance in complex microstructures with low computational requirements (4), and then show the coupling of this framework with a genetic algorithm to enable bottom-up electrode design (5). In our most recent effort, we are building topology optimization models of porous electrodes using multi-scale modeling of redox flow batteries, coupling computational macro- and meso-scale models of transport processes constructed using finite element and finite volume methods. We then couple these approaches with upscaling strategies that enable manufacturability of the structures. Second, I will describe a new approach to synthesizing porous electrodes based on non-solvent induced phase separation (NIPS) (6). NIPS is a simple and versatile fabrication method that can be used to synthesize morphologically-diverse electrode microstructures (e.g., isoporous, pore-size gradients, and multimodal porosity) by tuning simple parameters in the polymer solution, such as polymer concentration, solvent type, and temperature. Using a suite of microscopic, spectroscopic, and electrochemical diagnostic tools, I will present synthesis-property-performance relationships of the NIPS electrodes (7). Third and finally, I will highlight our efforts to functionalize porous electrode interfaces with organic molecules to impart targeted functional properties including hydrophilicity, kinetic activity (8), and selectivity (e.g. H2 evolution suppression). References A. Forner-Cuenca, F. R. Brushett, Curr. Opin. Electrochem. 18, 113–122 (2019).C. Minke, U. Kunz, T. Turek, J. Power Sources. 342, 116–124 (2017).M. L. Perry, K. E. Rodby, F. R. Brushett, ACS Energy Lett. 7, 659–667 (2022).M. van der Heijden, R. van Gorp, M. A. Sadeghi, J. Gostick, A. Forner-Cuenca, J. Electrochem. Soc. 169, 040505 (2022).R. van Gorp, M. van der Heijden, M. A. Sadeghi, J. Gostick, A. Forner-Cuenca, Chem. Eng. J. 455, 139947 (2023).C. T. Wan et al., Adv. Mater. 33, 2006716 (2021).R. R. Jacquemond et al., Cell Reports Phys. Sci. 3, 100943 (2022).E. B. Boz, P. Boillat, A. Forner-Cuenca, ACS Appl. Mater. Interfaces. 14, 41883–41895 (2022).

Giant sediment-wave field and supercritical flows in a distally steepened ramp, Fort Payne Formation (Lower Mississippian), Kentucky–Tennessee, U.S.A.

ABSTRACT Sediment waves are common in confined to unconfined settings on modern marine slopes and basin floors worldwide. Their morphology and stratal patterns show that many of them migrate upslope and upflow, a characteristic thought to record Froude-supercritical flow conditions associated with sediment gravity flows and density cascades. Few sediment waves of this type have been observed in the ancient rock record. This study reports the discovery of a giant (> 20,000 km2) sediment-wave field in Lower Mississippian carbonates and shales of the Fort Payne Formation in Tennessee and Kentucky, U.S.A. Sediment waves are present in the clinothem slopes and basin floor of a distally steepened ramp as seismic-scale bedforms ranging from 100 to 700 m long and 15 to 50 m high. Dominant facies include crinoidal shales, packstones, and rudstones. Many of the beds are sharp-based and graded, indicating sediment-gravity-flow deposition. Upslope-inclined rudstones (backsets) and wavy beds with upflow and downflow laminae are common and indicate supercritical flow conditions. These observations and interpretations are in stark contrast to previous interpretations of crinoidal bioherms and Waulsortian-type mounds. Basin physiography, a cool-water heterozoan carbonate factory and coastal upwelling were key factors in establishing a rapidly prograding ramp characterized by high rates of sediment production and basinward shedding. Sediment gravity flows and density cascades transported crinoidal grains downslope and entrained crinoids that inhabited the slope. Flows frequently reached Fr-supercritical flow conditions that led to the formation of sediment waves similar to those on modern marine slopes. This sediment-wave field is one of the first to be documented in the ancient rock record, and its extent is enormous. The near absence of other reported ancient examples must be due to misinterpretation (mounds, slumps) and the problem of observational scale and resolution. Sediment waves are often larger than outcrops. Lack of recognition of sediment waves in subsurface seismic sections is probably due to misinterpretation and insufficient resolution. Perhaps this study demonstrates the need for revisiting and updating existing facies models of carbonate-sediment transport and depositional processes across slopes and basin floors.

Hybrid and coupled modeling for the design of fixed and suspended biomass reactors treating sanitary landfill leachates

This paper deals with an approach for hybrid and coupled modeling of the design of fixed and suspended biomass reactors for organic matter removal from sanitary landfill leachates. Five bioreactors, comprising Rotating Biological Contactors, Trickling Filter, Upflow Anaerobic Sludge Blanket, Upflow Anaerobic Filter in Two Separated Stages (UAF-2SS) and Upflow Anaerobic Filter in Three Separated Stages (UAF-3SS) were evaluated by treating the organic matter contained in the leachates produced in two sanitary landfills. With respect to the hybrid and coupled models, the best performance in the approximation of the measured values in the Se/Si ratio to the predicted results of models were the equations for UAF-2SS and UAF-3SS reactors. Hybrid models were made up of a combination of mass conservation law and equations for estimating transformation process. Coupled models consisted of a combination of transport process models and transformation models based on the substrate utilization rate by the microorganisms.

Joint inversion of induced polarization and hydraulic tomography data for hydraulic conductivity imaging

SUMMARY For accurate modelling of groundwater flow and transport processes within an aquifer, precise knowledge about hydraulic conductivity K and its small-scale heterogeneities is fundamental. Methods based on pumping tests, such as hydraulic tomography (HT), allow for retrieving reliable K-estimates, but are limited in their ability to image structural features with high resolution, since the data from time-consuming hydraulic tests are commonly sparse. In contrast, geophysical methods like induced polarization (IP) can potentially yield structural images of much higher resolution, but depend on empirical petrophysical laws that may introduce significant uncertainties to the K-estimation. Therefore, this paper presents a joint inversion procedure for both HT and IP data, which allows for combining the complementary abilities of both methods. Within this approach, a traveltime inversion is applied to the HT data, while the IP inversion is based on a full-decay time-domain forward response, as well as a reparametrization of the Cole–Cole model to invert for K directly. The joint inversion is tested on a synthetic model mimicking horizontally layered sediments, and the results are compared with the individual HT and IP inversions. It is shown that jointly inverting both data sets consistently improves the results by combining the complementary sensitivities of the two methods, and that the inversion is more robust against changes in the experimental setups. Furthermore, we illustrate how a joint inversion approach can correct biases within the petrophysical laws by including reliable K-information from hydraulic tests and still preserving the high-resolution structural information from IP. The different inversion results are compared based on the structural similarity index (SSIM), which underlines the robustness of the joint inversion compared to using the data individually. Hence, the combined application of HT and IP within field surveys and a subsequent joint inversion of both data sets may improve our understanding of hydraulically relevant subsurface structures, and thus the reliability of groundwater modelling results.

Sensitivity of transport object control quality for measuring the inaccuracy of state variables

This work analyzes the sensitivity functions and optimum control of a transport and logistics process model. It explains the fundamental model of controlling safe ship movement as a differential game, and optimizing control algorithms through multi-matrix game and multi-stage positioning game. The sensitivity features for controlling safe ship in actual collision scenario are described in relation to inaccurate information of process position and variations in its varables, based on the determination of computer simulation algorithms in Matlab/Simulink software.

Analysis of world experience in the use of artificial intelligence in traffic control systems at various levels

When operating automated traffic control systems and their transformation into intelligent transport systems, modern requirements are imposed on the overall parameter safety, which characterizes the quality and efficiency of road traffic, especially when organizing high-speed loaded traffic of motor vehicles. The article discusses the use of various mathematical methods for these purposes when modeling transport processes and systems, including taking into account the development of artificial intelligence algorithms, so that when making decisions on traffic control, one can have reliable forecast indicators obtained from adequate models. A comparison of the models is made and recommendations are given on their applicability and the results obtained for traffic management purposes.

MALTA: A Zonally Averaged Global Atmospheric Transport Model for Long‐Lived Trace Gases

AbstractWe present a two‐dimensional, zonally averaged global model of atmospheric transport named MALTA: Model of Averaged in Longitude Transport in the Atmosphere. It aims to be accessible to a broad community of users, with the primary function of quantifying emissions of greenhouse gases and ozone depleting substances. The model transport is derived from meteorological reanalysis data and flux‐gradient experiments using a three‐dimensional transport model. Atmospheric sinks are prescribed loss frequency fields. The zonally averaged model simulates important large‐scale transport features such as the influence on trace gas concentrations of the quasi‐biennial oscillation and variations in inter‐hemispheric transport rates. Stratosphere‐troposphere exchange is comparable to a three‐dimensional model and inter‐hemispheric transport is faster by up to 0.3 years than typical transport times of three‐dimensional models, depending on the metric used. Validation of the model shows that it can estimate emissions of CFC‐11 from an incorrect a priori emissions field well using three‐dimensional (3D) mole fraction fields generated using a different 3D model than which the flux gradient relationships were derived. The model is open source and is expected to be applicable to a wide range of studies requiring a fast, simple model of atmospheric transport and chemical processes for estimating associated emissions or mole fractions.

Identification of transport and technological problems in the grain product subcomplex

The study focuses on the grain-product subcomplex within the Republic of Kazakhstan, aiming to dissect and address the prevalent issues plaguing this sector. It identifies several challenges, including technological deficiencies, inefficiencies, and increased production risks. There was a notable decrease in fixed capital investment in the agricultural sector in 2023, suggesting a shift in investment strategies or priorities, particularly with a significant reduction in food production investments. Agricultural exports in 2023, while showing a decrease compared to 2022, still represent a substantial economic activity. The capacity and utilization of grain storage facilities indicate a robust infrastructure capable of supporting the nation's grain production, with a considerable portion of storage capacity currently utilized and a significant amount of grain released in 2023. Furthermore, the research delves into cross-border rail transport of crops, with Uzbekistan emerging as a regional leader in exports. This analysis, along with the examination of export activities and grain storage capacities, emphasizes the role of innovation and technological advancements in enhancing the agroindustrial sector's efficiency and competitiveness. Optimization methods for modeling transport processes in agribusiness, such as digital technologies and intermodal transport, are proposed to address existing shortcomings. The study's findings are distinguished by their complex approach to addressing the problems within the grain-product subcomplex. This approach, highlighting the practical application under local conditions, makes the results uniquely tailored to Kazakhstan's context, offering a pathway towards improved agricultural practices and sectoral growth

Modeling of transportation and technological processes in automated systems

The purpose of the study is to create a problem-oriented model of transport and technological processes in automated systems. To achieve this goal, it is necessary to develop methodological aspects of creating an automated modeling system. The content of the basic principles of problem-oriented modeling in the study of an integrated automated system for managing stocks and transport and technological processes is revealed in the paper. At the same time, methodological aspects of creating automated modeling systems, namely, a conceptual mathematical model for the analysis and standardization of technical and economic indicators are considered. The functioning of logistics systems, namely, system modeling (supply — transport) is also considered. The problems of interaction and relationships, optimization of resource flows, and increasing the efficiency of management decisions making have been solved. It is shown that modeling resource flows involves adjustments through iterative redistribution of interregional and intraregional supplies among suppliers and consumers. Combining product items into one delivery leads to savings in stocks formation costs by reducing the number of orders. To create effective automated control systems, it is necessary to study in detail the primary object — the logistics and technical support system itself. The creation of applied mathematical and software is a promising direction for solving this problem and developing it as an automated modeling system. In this regard, when creating such automated control systems, it is most advisable to use a model-oriented approach, which is based on the principles of system analysis, standardization, classification and modularity. Thus, it is shown that the use of the problem-oriented approach to creating an automated modeling system makes it possible to reduce the labor intensity of its development and implementation, to provide the opportunity to unify algorithms for solving a problem, but also to apply standard methods for processing experimental results.

Enhancing hydro-epidemiological modelling of nearshore coastal waters with source-receptor connectivity study

Faecal Indicator Organism (FIO) concentrations in nearshore coastal waters may lead to significant public health concerns and economic loss. A three-dimensional numerical source-receptor connectivity study was conducted to improve the modelling of FIO transport and decay processes and identify major FIO sources impacting sensitive receptors (source apportionment). The study site was Swansea Bay, UK and the effects of wind, density, and tracer microbe (surrogate FIO) decay models were investigated by comparing the model simulations to microbial tracer field studies. The relevance of connectivity tests to source apportionment was demonstrated by hindcasting FIO concentration in Swansea Bay with the identified FIO source and the Impulse Response Function (IRF) in Control System theory. This is the first time the IRF approach has been applied for FIO modelling in bathing waters. Results show the importance of density, widely ignored in fully mixed water bodies, and the potential for biphasic decay models to improve prediction accuracy. The microbe-carrying riverine freshwater, having a smaller hydrostatic pressure, could not intrude on the heavier seawater and remained in the nearshore areas. The freshwater and the associated tracer microbes then travelled along the shoreline and reached bathing water sites. This effect cannot be faithfully modelled without the inclusion of the density effect. Biphasic decay models improved the agreement between measured and modelled microbe concentrations. The IRF hindcasted and measured FIO concentrations for Swansea Bay agreed reasonably, demonstrating the importance of connectivity tests in identifying key FIO sources. The findings of this study, namely enhancing hydro-epidemiological modelling and highlighting the effectiveness of connectivity studies in identifying key FIO sources, directly benefit hydraulics and water quality modellers, regulatory authorities, water resource managers and policy.

КЛЮЧОВІ ЗАВДАННЯ ПОВОЄННОГО ВІДНОВЛЕННЯ ГРОМАДСЬКОГО ЕЛЕКТРОТРАНСПОРТУ УКРАЇНИ

One of the most affected sectors of Ukraine’s economy during the full-scale invasion has been passenger transportation. Despite all difficulties, the transport sector continues to function, fulfilling its primary tasks and maintaining stable mobility in the country. The article highlights the key tasks for the post-war recovery and development of Ukraine’s public transport, regardless of the ownership forms of transport companies' assets. The focus is placed not on specific issues of sector recovery but on global strategies and methodologies essential for the national economy. Four tasks have been identified, encompassing various aspects of public transport operations, including economic, legal, technical, technological, staffing, and managerial dimensions. The article proposes a comprehensive and multifaceted approach to the recovery and development of public transport, grounded in rigorous economic calculations and modeling of future transport processes. It is noted that, despite the overall slowdown in economic growth, the transport sector remains a key driver of recovery. Urban public transport is expected to face increased demand in the post-war period. Thus, a sector-specific plan must be developed and implemented to meet the population's demand for urban transportation in the post-war period. The recovery plan for public transport should include the following key points: A centralized approach to industry development with appropriate budget allocations. Payments to transport companies strictly based on their completed transport work (implementation of EU Regulation 1370). Acquisition of rolling stock and the renewal of transport infrastructure as interconnected priorities, with infrastructure renewal being the primary task. The involvement of predominantly Ukrainian companies in the recovery of public transport, which will create additional jobs for Ukrainians returning from the frontlines or abroad. This, in turn, will increase budget revenues, enabling the country to finance the military and repay debts currently being accumulated.Тhat only by relying on advanced economic science can the sector's crisis state be overcome, enabling municipal transport enterprises to achieve break-even operations and, eventually, profit.

Features of transport flow modeling in projects of sustainable development in urban areas

The paper highlights the problems of modern Russian cities that significantly affect their socio-economic development. Most of the problems are related to the transport and logistics system due to the historical design of urban neighborhoods, chaotic and point development, and the increasing importance of road transport. All this supports the need to develop comprehensive projects for the development of urban areas. It is impossible without the use of specialized software tools, which are based on all aspects of the territory being modernized. The use of a set of methods, based on structural analysis and simulation modeling, allowed us to obtain formal models of transport processes associated with Yeniseyskaya Street in the city of Moscow. Based on the obtained models, examples of created scenarios for forecasting changes in the processes of the object of study over time during the modernization of its individual elements are presented.

Consistent Modeling of Transport Processes and Travel Times—Coupling Soil Hydrologic Processes With StorAge Selection Functions

AbstractUnderstanding the transport processes and travel times of pollutants in the subsurface is crucial for an effective management of drinking water resources. Transport processes and soil hydrologic processes are inherently linked to each other. In order to account for this link, we couple the process‐based hydrologic model RoGeR with StorAge Selection (SAS) functions. We assign to each hydrological process a specific SAS function (e.g., power law distribution function). To represent different transport mechanisms, we combined a specific set of SAS functions into four transport model structures: complete‐mixing, piston flow, advection‐dispersion and advection‐dispersion with time‐variant parameters. In this study, we conduct modeling experiments at the Rietholzbach lysimeter, Switzerland. All modeling experiments are benchmarked with HYDRUS‐1D. We compare our simulations to the measured hydrologic variables (percolation and evapotranspiration fluxes and soil water storage dynamics) and the measured water stable isotope signal (18O) in the lysimeter seepage for a period of ten years (1997–2007). An additional virtual bromide tracer experiment was used to benchmark the models. Additionally, we carried out a sensitivity analysis and provided Sobol indices for hydrologic model parameters and SAS parameters. Our results indicate that the advection‐dispersion transport model produces the best results. And thus, advective‐dispersive transport processes play a dominant role at Rietholzbach lysimeter. Our modeling approach provides the capability to test hypotheses of different transport mechanisms and to improve process understanding and predictions of transport processes. Overall, the combined model allows a very effective simulation of combined flux and transport processes at various temporal and spatial scales.

Mathematical modeling and research of transport flows and processes of transport systems of cities

The problem of mathematical modeling and research of transport flows and processes of transport systems of cities is set and solved. Related works, methods, modeling of traffic flow intensity as a first-order autoregression process, finding estimates of process model parameters with a standard normal random component are considered.