Mitigation Algorithm Research Articles

Chromatic dispersion-aware Tx and LO laser phase noise independent estimation enabled by dual pilot tones in DSCM systems

In the backbone networks employing high modulation formats such as 64QAM and metropolitan area networks, data center interconnection networks using the distributed feedback (DFB) lasers with several megahertz laser linewidths dramatically degrades system performance in the equalization enhanced phase noise (EEPN). Even though digital subcarrier multiplexing (DSCM) systems are known for their tolerance to EEPN, they still cause performance degradation in this case. Therefore, the EEPN mitigation algorithm becomes an indispensable part of DSP algorithms in DSCM systems. A dual pilot tone-based chromatic dispersion-aware transmitter and local oscillator laser phase noise independent estimation algorithm is proposed in this paper to solve the above problem. Simulations/offline experiment results under 5 MHz laser linewidth and 1000/800 km transmission indicate that the proposed algorithm could bring about 1/0.6 dB improvement of the required SNR for the normalized generalized mutual information of 0.9 compared with the blind phase searching algorithm.

Research on a multi-source rfi mitigation algorithm using a reference antenna array

Abstract We propose a multi-source RFI (Radio Frequency Interference) mitigation method based on a reference antenna array to address the challenge of RFI from multiple directions in radio observation equipment. It introduces a sampling point correction technique using a multi-channel parallel cross-correlation computation method, enhancing the effectiveness of frequency domain adaptive RFI fast mitigation algorithms. The design implements an RFI component detection method based on cross-correlation coefficient thresholds to effectively reduce new interference frequency components introduced by the reference antenna array. Simulated RFI signals and baseband signals of pulsar J0332+5434 observed by the NanShan 26-meter Radio Telescope (NSRT) were used to test the algorithm proposed in this paper. Simulation results demonstrate that the simulated radio telescope signals after RFI mitigation closely match the original pulsar data in profile and phase, confirming the effectiveness of the proposed method.

Sky-GVIO: Enhanced GNSS/INS/Vision Navigation with FCN-Based Sky Segmentation in Urban Canyon

Accurate, continuous, and reliable positioning is critical to achieving autonomous driving. However, in complex urban canyon environments, the vulnerability of stand-alone sensors and non-line-of-sight (NLOS) caused by high buildings, trees, and elevated structures seriously affect positioning results. To address these challenges, a sky-view image segmentation algorithm based on a fully convolutional network (FCN) is proposed for NLOS detection in global navigation satellite systems (GNSSs). Building upon this, a novel NLOS detection and mitigation algorithm (named S−NDM) uses a tightly coupled GNSS, inertial measurement units (IMUs), and a visual feature system called Sky−GVIO with the aim of achieving continuous and accurate positioning in urban canyon environments. Furthermore, the system combines single-point positioning (SPP) with real-time kinematic (RTK) methodologies to bolster its operational versatility and resilience. In urban canyon environments, the positioning performance of the S−NDM algorithm proposed in this paper is evaluated under different tightly coupled SPP−related and RTK−related models. The results exhibit that the Sky−GVIO system achieves meter-level accuracy under the SPP mode and sub-decimeter precision with RTK positioning, surpassing the performance of GNSS/INS/Vision frameworks devoid of S−NDM. Additionally, the sky-view image dataset, inclusive of training and evaluation subsets, has been made publicly accessible for scholarly exploration.

Enhancing fairness in AI-enabled medical systems with the attribute neutral framework

Questions of unfairness and inequity pose critical challenges to the successful deployment of artificial intelligence (AI) in healthcare settings. In AI models, unequal performance across protected groups may be partially attributable to the learning of spurious or otherwise undesirable correlations between sensitive attributes and disease-related information. Here, we introduce the Attribute Neutral Framework, designed to disentangle biased attributes from disease-relevant information and subsequently neutralize them to improve representation across diverse subgroups. Within the framework, we develop the Attribute Neutralizer (AttrNzr) to generate neutralized data, for which protected attributes can no longer be easily predicted by humans or by machine learning classifiers. We then utilize these data to train the disease diagnosis model (DDM). Comparative analysis with other unfairness mitigation algorithms demonstrates that AttrNzr outperforms in reducing the unfairness of the DDM while maintaining DDM’s overall disease diagnosis performance. Furthermore, AttrNzr supports the simultaneous neutralization of multiple attributes and demonstrates utility even when applied solely during the training phase, without being used in the test phase. Moreover, instead of introducing additional constraints to the DDM, the AttrNzr directly addresses a root cause of unfairness, providing a model-independent solution. Our results with AttrNzr highlight the potential of data-centered and model-independent solutions for fairness challenges in AI-enabled medical systems.

Optimizing Underground Coal Mine Safety: Leveraging Advanced Computational Algorithms for Roof Fall Rate Prediction and Risk Mitigation

AbstractThe utilization and consumption of coal in various nations have emphasized the pivotal role played by coal mines. However, aside from the substantial contribution of coal mines, miners, engineers, and craftsmen in this industry have long been exposed to numerous risks and financial losses resulting from roof collapses in underground coal mines. Hence, due to the heightened sensitivity surrounding this issue, the accurate and low-error forecasting and assessment of the roof fall rate (RFR) are deemed crucial and of utmost importance. Nonetheless, due to the intricate and uncertain inherent characteristics of the rock formations, assessing the RFR has encountered multiple challenges that cannot be precisely approximated through traditional methods. In this paper, algorithms such as the harmony search algorithm (HS) and the invasive weed Optimization algorithm (IWO) are harnessed to address the aforementioned challenges. To model the RFR, a total of 109 data points were used, incorporating input parameters such as primary roof support (PRSUP), depth of cover (D), coal mine roof rating (CMRR), mine height (MH), and intersection diagonal span (IS). For effective data analysis and model development, the dataset was split into two separate groups: one for training and the other for testing. Specifically, 80% of the data was used to build the model, while the remaining 20% was allocated for model evaluation and validation. Based on the outcomes of three statistical metrics R2, MSE, and RMSE, it is evident that the deployment of HS and IWO algorithms demonstrates high performance, with predicted values closely aligning with actual ones. Consequently, the utilization of intelligent algorithms in the field of rock engineering is positioned as a potent tool for researchers and engineers. In conclusion, a sensitivity analysis is carried out with the help of the @RISK software as a means of ranking the influence that the input parameters have on the output of the model. Its results indicate that among different parameters, the CMRR parameter with a sensitivity degree of 0.11 has the most impact on the model, even with the smallest change in this parameter, a significant change is made in the model output.

INS/UWB multi-sensor integrated localization scheme in indoor LOS/NLOS environment based on MEF-GPDAF

Localization technology is crucial for indoor robot navigation. Wireless sensor network (WSN) serves as a significant part in indoor localization. However, the intricate indoor conditions make signal propagation susceptible to interference from obstructions, resulting in a decrease in positioning accuracy. Inertial Navigation System (INS) operates as a self-governing navigational setup undisturbed by indoor environment, and its location determinations remain unaltered by non-line-of-sight (NLOS) conditions. This research presents a combined positioning method of Ultra-wide band (UWB) and INS, which inherits advantages of the two subsystems and elevates the positioning system performance . On the basis of INS autonomous positioning, the maximum entropy fuzzy generalized probability data association filter (MEF-GPDAF) is used to modify the INS positioning results by combining the position of beacon nodes. When using UWB to locate the mobile node, a NLOS mitigation algorithm is applied to lessen the influence of NLOS propagation. Simulation experiment results demonstrate that, when compared to existing algorithm, MEF-GPDAF exhibits superior positioning precision.Meanwhile, in the real environment, the average error of the algorithm of MEF-GPDAF was measured to be 0.4961 m, which improved its accuracy by 32.88 % compared with the latest algorithm.

Increasing the Measured Effective Quantum Volume with Zero Noise Extrapolation

Quantum volume is a full-stack benchmark for near-term quantum computers. It quantifies the largest size of a square circuit which can be executed on the target device with reasonable fidelity. Error mitigation is a set of techniques intended to remove the effects of noise present in the computation of noisy quantum computers when computing an expectation value of interest. Effective quantum volume is a proposed metric that applies error mitigation to the quantum volume protocol to evaluate the effectiveness not only of the target device but also of the error mitigation algorithm. Digital zero-noise extrapolation is an error mitigation technique that estimates the noiseless expectation value using circuit folding to amplify errors by known scale factors and then extrapolating computed expectation values to the zero-noise limit. Here we demonstrate that zero-noise extrapolation, with global and local unitary folding with fractional scale factors, in conjunction with dynamical decoupling, can increase the effective quantum volume over the vendor-measured quantum volume. Specifically, we measure the effective quantum volume of four IBM Quantum superconducting processor units, obtaining values that are larger than the vendor-measured quantum volume on each device. This is the first such increase reported.

Design of a Suspension Controller with an Adaptive Feedforward Algorithm for Ride Comfort Enhancement and Motion Sickness Mitigation

Design of a Suspension Controller with an Adaptive Feedforward Algorithm for Ride Comfort Enhancement and Motion Sickness Mitigation

Mitigating Sociodemographic Bias in Opioid Use Disorder Prediction: Fairness-Aware Machine Learning Framework.

Opioid use disorder (OUD) is a critical public health crisis in the United States, affecting >5.5 million Americans in 2021. Machine learning has been used to predict patient risk of incident OUD. However, little is known about the fairness and bias of these predictive models. The aims of this study are two-fold: (1) to develop a machine learning bias mitigation algorithm for sociodemographic features and (2) to develop a fairness-aware weighted majority voting (WMV) classifier for OUD prediction. We used the 2020 National Survey on Drug and Health data to develop a neural network (NN) model using stochastic gradient descent (SGD; NN-SGD) and an NN model using Adam (NN-Adam) optimizers and evaluated sociodemographic bias by comparing the area under the curve values. A bias mitigation algorithm, based on equality of odds, was implemented to minimize disparities in specificity and recall. Finally, a WMV classifier was developed for fairness-aware prediction of OUD. To further analyze bias detection and mitigation, we did a 1-N matching of OUD to non-OUD cases, controlling for socioeconomic variables, and evaluated the performance of the proposed bias mitigation algorithm and WMV classifier. Our bias mitigation algorithm substantially reduced bias with NN-SGD, by 21.66% for sex, 1.48% for race, and 21.04% for income, and with NN-Adam by 16.96% for sex, 8.87% for marital status, 8.45% for working condition, and 41.62% for race. The fairness-aware WMV classifier achieved a recall of 85.37% and 92.68% and an accuracy of 58.85% and 90.21% using NN-SGD and NN-Adam, respectively. The results after matching also indicated remarkable bias reduction with NN-SGD and NN-Adam, respectively, as follows: sex (0.14% vs 0.97%), marital status (12.95% vs 10.33%), working condition (14.79% vs 15.33%), race (60.13% vs 41.71%), and income (0.35% vs 2.21%). Moreover, the fairness-aware WMV classifier achieved high performance with a recall of 100% and 85.37% and an accuracy of 73.20% and 89.38% using NN-SGD and NN-Adam, respectively. The application of the proposed bias mitigation algorithm shows promise in reducing sociodemographic bias, with the WMV classifier confirming bias reduction and high performance in OUD prediction.

Dual-polarization carrier-assisted differential detection with asymmetric twin-SSB modulation and simplified receiver structure

Carrier-assisted differential detection (CADD) is a promising solution for high-capacity and cost-sensitive short-reach application scenarios, in which the optical field of a complex-valued double-sideband (CV-DSB) signal is reconstructed without using a local oscillator laser. In this work, we propose a polarization division multiplexed asymmetric twin single-sideband CADD (PDM-ATSSB CADD) scheme to realize the optical field recovery of the PDM CV-DSB signals. The polarization fading is solved by using a pair of optical bandpass filters (OBPFs) to suppress the unwanted other polarized offset carrier and signal, and the dual-polarization optical field is recovered by the CADD receiver. An asymmetric twin-SSB signal is used to relax the sharpness requirement of optical filter edges. We also propose a joint signal-signal beat interference (SSBI) iterative mitigation algorithm, which can effectively mitigate intra- and inter-polarization SSBI. The proposed PDM-ATSSB CADD scheme is validated for 30 Gbaud PDM asymmetric twin-SSB 16-ary quadrature amplitude modulation signals. We illustrate the parameter optimization process for PDM-ATSSB CADD, including optical delay and the number of iterations. The impacts of phase noise and relative intensity noise for laser and polarization impairment on PDM-ATSSB CADD are evaluated through numerical simulation. Compared with the PDM-symmetric-TSSB CADD (PDM-STSSB CADD), the required frequency gap to reach the 7% FEC threshold can be reduced by 1 GHz, and the OSNR sensitivity is improved by about 3 dB. Moreover, two simplified PDM-ATSSB CADD schemes are proposed and discussed, which could be considered hardware-efficient and integrative candidates for metro and inter-data center interconnects.

Frame-rate adaptive fractionally spaced equalization enabled high-throughput optical camera communication.

Optical camera communication (OCC) has garnered worldwide research attention, due to its immunity to electromagnetic interference (EMI) and efficient utilization of spectrum resources. However, the limited bandwidth of the OCC system and the timing offset of the camera result in low system throughput. To enhance the OCC throughput, we propose and experimentally demonstrate a frame-rate adaptive fractionally spaced equalization algorithm (FA-FSE) for the joint mitigation of severe inter-symbol interference (ISI) and timing offset arising in OCC. Experimental results validate its correct and power-efficient function, leading to a record aggregated throughput of 250.96 kbit/s, when the 8-level pulse amplitude modulation (PAM-8) signals are independently modulated to eight chip-on-board light emitting diode (COB-LED) light strips, while simultaneously received by a smartphone 10 cm away.

A New Mitigation Method against DRDoS Attacks Using a Snort UDP Module in Low-Specification Fog Computing Environments

Current cloud computing expects to face huge traffic costs, data loads, and high latency due to the explosion of data from devices as the IoT and 5G technology evolve. Fog computing has emerged to overcome these issues. It deploys small fog servers at the edge of the network to process critical data in real time while sending the remaining secondary tasks to the central cloud, instead of sending massive amounts of data to the cloud. With the rise in fog computing, among traditional security threats, distributed denial-of-service (DDoS) attacks have become the major threat to availability. This is especially true for fog computing, where real-time processing is critical; there are many fog servers, and the processing power is relatively low. Distributed reflection denial-of-service (DRDoS), one of the frequently used DDoS attack techniques, is an amplification attack that can be used on a small or large scale. It is widely used in attack tools due to its easy configuration. This study analyzes the characteristics of fog computing, the characteristics of DRDoS attacks, and the advantages and disadvantages of existing countermeasures. Based on these analyses, this study proposes a model that could effectively mitigate attacks even on low-specification fog servers by combining a modified Snort module with reduced functionality, simple pattern matching, and filtering distribution using Anycast. This mitigation algorithm has a simple structure rather than a complex filtering structure. To achieve this goal, this study virtually implemented the corresponding fog IoT environment. In spite of its simple structure, it proved that the fog server could secure availability even under DRDoS attacks by implementing and validating the mitigation model.

A novel heuristic algorithm for disruption mitigation in a global food supply chain

The Global Food Supply Chain (GFSC) often encounters challenges in maintaining the continuous flow of essential food products such as rice and wheat. In this paper, we consider possible disruptions in supply and transportation in GFSC. Disruptions may cause severe food shortages in some parts of the world. Moreover, a disruption is not necessarily a single independent event, as multiple disruptions may occur sequentially or simultaneously. After any interruption, it is essential to reoptimize the remaining flow activities in a short period under the changed conditions. Although both the initial flow plan and post-disruption plan can be generated by formulating them as Mixed Integer Linear Programming (MILP) models, such a mitigation plan is challenging because of time constraints and when multiple disruptions are considered. To address this issue, we proposed a novel heuristic algorithm that revises the ideal plan in the event of a disruption. The developed heuristic can deal with different types of disruptions, as well as a series of disruptions. The performance of the heuristic was judged by solving 300 problem instances and comparing the results with those obtained from the exact method. To demonstrate the applicability of the proposed algorithm in practice, we have solved three real-world disruption Scenarios. The analysis of results uncovered crucial managerial insights, recommending strategies for disruption mitigation, and proved to be an effective method for post-disruption planning.

CONTAIN: A community-based algorithm for network immunization

Network immunization is an automated task in the field of network analysis that involves protecting a network (modeled as a graph) from being infected by an undesired arbitrary diffusion. In this article, we consider the spread of harmful content in social networks, and we propose CONTAIN, a novel COmmuNiTy-based Algorithm for network ImmuNization. Our solution uses the network information to (1) detect harmful content spreaders, and (2) generate partitions and rank them for immunization using the subgraphs induced by each spreader, i.e., employing CONTAIN. The experimental results obtained on real-world datasets show that CONTAIN outperforms state-of-the-art solutions, i.e., NetShield and SparseShield, by immunizing the network in fewer iterations, thus, converging significantly faster than the state-of-the-art algorithms. We also compared our solution in terms of scalability with the state-of-the-art tree-based mitigation algorithm MCWDST, as well as with NetShield and SparseShield. We can conclude that our solution outperforms MCWDST and NetShield.

Radio Frequency Interference Mitigation in Data and Image Bi-Domains for an Aperture Synthesis Radiometer

For synthetic aperture microwave radiometers, the problem of Radio Frequency Interference (RFI) is becoming more and more serious, which affects both the scientific retrieval of remote sensing data and the imaging quality of brightness temperature (BT) images. In the visibility data domain, the array factor synthesis algorithm is commonly employed to mitigate RFI sources and their Gibbs trailing. In the BT image domain, the CLEAN algorithm is typical applied to mitigate RFI sources and their Gibbs trailing. However, the array factor synthesis algorithm can result in anomalous BT points near the “zero trap” region, and the CLEAN algorithm will miss some BT points below a certain threshold. In this paper, a Bi-domain combined mitigation algorithm is proposed to mitigate RFI sources and their Gibbs trailing. Following initial mitigation in the visibility data domain, dual thresholds are applied to normalize anomalous BT points near the “zero trap” region, thereby enhancing imaging quality. The effectiveness of the Bi-domain combined mitigation algorithm is verified by using both measured data from SMOS L1A and simulated data. The experimental results demonstrate that the Bi-domain combined mitigation algorithm is superior to the array factor synthesis algorithm and the CLEAN algorithm in mitigating RFI sources and their Gibbs trailing.

Optimizing power system stability: A hybrid approach using manta ray foraging and Salp swarm optimization algorithms for electromechanical oscillation mitigation in multi‐machine systems

AbstractThis paper emphasizes the significance of ensuring adequate damping of electromechanical oscillations in power systems to ensure stable operation. Power System Stabilizers (PSSs) are influential in enhancing system damping and refining dynamic characteristics during transient conditions. However, the efficacy of PSSs is notably contingent on parameter values, particularly in the case of lead‐lag PSSs. In response to this challenge, the paper introduces a Tilt‐Integral‐Derivative (TID)‐based PSS, optimized through a novel optimization algorithm called Hybrid Manta Ray Foraging and Salp Swarm Optimization Algorithms (MRFOSSA). The MRFOSSA algorithm demonstrates robustness and enhanced convergence, validated through benchmark function tests, and outperforms competing algorithms. These superior characteristics of MRFOSSA were employed in optimal tuning of TID‐PSSs to uphold the stability of multi‐machine power systems. The MRFOSSA algorithm demonstrates robustness and enhanced convergence, outperforms competing algorithms in the optimal tuning of TID‐PSS within the Western System Coordinating Council (WSCC)‐3‐machines 9‐bus test system. In summary, the proposed TID‐PSS, coupled with the MRFOSSA algorithm, presents a promising avenue for enhancing power system stability.

A hardware-in-the-loop (HIL) testbed for cyber-physical energy systems in smart commercial buildings

In recent years, there has been a growing trend toward the development of smart buildings that rely on cyber-physical systems (CPS) to optimize occupant comfort, safety, and energy efficiency. To ensure the reliable and efficient operation of CPS with designed control strategies, it is important to evaluate their performance under various scenarios before deploying them in the real world. This is where a Hardware-in-the-loop (HIL) testbed designed for studying sensor and control-related studies in smart buildings can be highly valuable. With the growing threat of cyber-attacks and physical faults targeting smart buildings, it is essential to ensure the security of building operations. A HIL testbed can emulate cyber-attack and physical fault scenarios, allowing researchers to develop and test threat detection and mitigation algorithms. This enables researchers to identify potential issues and optimize the algorithms in a safe and controlled environment before they are deployed in real-world settings, reducing the risk of failures that can negatively impact occupant comfort, safety, and energy efficiency. Therefore, this paper developed a HIL testbed designed for cyber-physical energy systems (e.g. buildings automation system (BAS)) in smart commercial buildings. The HIL testbed is comprised of a real-time building and Heating, Ventilation, and Air-Conditioning (HVAC) emulator using Modelica-based dynamic models, a set of BAS controllers, and a BAS computer server. The data generation capability of the HIL testbed is demonstrated by tracking normal and faulty operating data in the BAS, as well as monitoring detailed network traffic in the local BAS network. This study further demonstrates the HIL testbed’s capability by conducting case studies on real-time physical fault and cyber-attack experiments using a Department of Energy (DOE) prototype commercial building. It is anticipated that the fully functional HIL testbed will be utilized for a variety of sensor and control-related studies, including but not limited to testing, developing, validating of different HVAC control strategies, fault detection & diagnosis, energy monitoring and analysis, cyber security study, etc.

Securing the Internet of Things: Predictive Defense Algorithm for Attack Mitigation

The Internet of Things (IoT) presents unprecedented opportunities for connectivity and efficiency across various sectors. However, its decentralized nature and the vast number of interconnected devices also pose significant security challenges, making IoT networks vulnerable to cyber-attacks. In this paper, we propose a predictive defense algorithm leveraging Differential Privacy (DP) techniques to enhance IoT security. By analyzing historical attack data while preserving the privacy of sensitive information, our algorithm predicts potential cyber threats and proactively mitigates them before they manifest. We present the theoretical framework of the DP algorithm, its implementation in IoT environments, and evaluate its effectiveness through simulations and real-world experiments. Our results demonstrate the algorithm’s ability to accurately predict and prevent a wide range of attacks, thus bolstering the resilience of IoT ecosystems against evolving cyber threats.

Interactive Human-Centric Bias Mitigation

Bias mitigation algorithms differ in their definition of bias and how they go about achieving that objective. Bias mitigation algorithms impact different cohorts differently and allowing end users and data scientists to understand the impact of these differences in order to make informed choices is a relatively unexplored domain. This demonstration presents an interactive bias mitigation pipeline that allows users to understand the cohorts impacted by their algorithm choice and provide feedback in order to provide a bias mitigated pipeline that most aligns with their goals.

OPTIMAL LOCATION AND SIZING OF DG IN DISTRIBUTION NETWORK: IMPACT ON OVERCURRENT DISTRIBUTION PROTECTION SCHEME

The integration of distributed generation (DG) into the existing distribution networks minimizes active power losses and improves the voltage profile. The recent improvement in the development of DG technology has caused increase in the penetration of DG from different sources. The optimal location and sizing of DG is very challenging and introduces different protection issues. This is caused by penetration of current flow from different source which is contrary to the principles of operation of the conventional overcurrent scheme. This paper presents optimal method of DG placement and sizing using firefly algorithm and its impact of DG penetration on overcurrent protection scheme. Low voltage distribution network is modelled and simulated in PSCAD/EMTDC and DigSilent power factory software using IEEE 33 and Ayepe 34 standard bus. False tripping of feeders, Nuisance tripping, blinding of the protection scheme and unintentional islanding caused as result of Photovoltaic penetration into the distribution network were simulated. Coordination of overcurrent relays with and without DG penetration were analyzed and possible mitigation algorithm were proposed. The simulation result obtained showed that the proposed methods significantly improve the protection scheme coordination..