Minimum Particle Size Research Articles

Analytical model for fracture conductivity with multiple particle sizes and creep deformation

The prediction of fracture conductivity in shale reservoirs is necessary for hydraulic fracturing optimization. However, problems remain with the prediction of fracture conductivity in shale reservoirs. Shale exhibits creep deformation behavior. In addition, due to the combination of large and small particle sizes, proppant, and discontinuous distribution fractures, it is challenging to establish an embedment and fracture conductivity model that combines the creep factor and multiple particle sizes.Based on the authors’ previous work, the modified Burgers creep model was introduced into the discontinuous embedment model for multiple particle sizes, and then combined with the KC equation for multiple particle sizes to develop an embedment depth and conductivity prediction model under the conditions of creep and discontinuous distribution of multiple-particle-size proppants.The results showed that the creep time increased from 10 d to 100 d, and the critical closure pressure of the minimum particle size proppant embedded in the rock decreased from 36 MPa to 14 MPa. The closure pressure increased from 20 MPa to 40 MPa, and the critical creep time of the minimum particle size proppant embedded in the rock decreased from 30 d to 12 d. Under the condition of two-particle-size proppant combinations, there is a proppant combination ratio that minimizes the fracture conductivity, which was approximately 0.2 in this study. The longer the creep time, the greater the optimal proppant distance coefficient. The greater the viscosity of the rock and proppant, the smaller the optimal proppant distance coefficient. These research results provide a theoretical basis for optimizing the local conductivity of secondary fractures in shale reservoirs.

FRACTAL CHARACTERISTICS OF LOW-PERMEABILITY SANDSTONE RESERVOIRS

The sandstone micro-structure is one of the most important parameters for quantitative evaluation of groundwater/oil/gas resources and prediction of flow rates of water/oil/gas. In this study, we applied seven low-permeability sandstone samples obtained from North China to study the structures of pore and solid phase based on digital core technology and the fractal theory. In this work, rock images were collected by scanning electron microscopy (SEM), and then image software (image pro plus) was applied to convert the SEM images into binary images and calculated the perimeter and area of pores and particles. Using the fractal medium criterion, we analyzed the fractal characteristics of pore and solid phases, and then we extended the criterion from the pore phase to both pore and solid phases. This paper explores the relationship among the pore and solid phase fractal characteristics, porosity, pore size, particle size and fractal dimensions for pores and particles. The results were compared with the experimental data and showed that the solid phase satisfies the fractal distribution, while the pore phase dissatisfies the fractal distribution. It was also found that the minimum and maximum pore and particle sizes, magnification times have a significant effect on the results. In addition, by introducing the diameter and mean hydraulic radius into Ergun–Wu equation, the permeabilities of the samples were calculated.

Ultrasonic enhanced emulsification process in 3D printed microfluidic device to encapsulate active pharmaceutical ingredients

A new method to prepare polymer encapsulated repaglinide nanoparticles through ultrasonic enhanced microchannel emulsification technique was explored. Using the concept of 3D printing, three different shaped micromixers (T-type, Y-type, and F-type) followed by a serpentine microchannel was fabricated using SS-316. Parametric study was performed on all three fabricated micromixers. The best results were obtained for the Y-microchannel in a microfluidic system alone, which showed a minimum particle size of 513.6 nm with 75.4% encapsulation efficiency (EE). In the selected microchannel, to further reduce the drug particle size and to increase% EE, convective mixing between immiscible fluids was enhanced by implementing ultrasound. Compared to the microfluidic system, particle size and EE were significantly improved in the ultrasonic microfluidic system. The experimental results revealed that the minimum particle size of 75.4 ± 1.3 nm with 82.9 ± 0.2% EE was achieved using an ultrasonic enhanced microfluidic system. The zeta potential of + 29.5 mV was obtained for emulsion prepared using the ultrasonic microfluidic system, whereas + 22 mV was prepared using a microfluidic system. Moreover, a backscattering measurement was performed to predict the stability of prepared emulsions. Integrating the ultrasound with a microfluidic system has proven beneficial for drug encapsulation.

Development and Optimization of Hyaluronic Acid-Poloxamer In-Situ Gel Loaded with Voriconazole Cubosomes for Enhancement of Activity against Ocular Fungal Infection.

Fungal eye infections are largely disseminated, especially in developing countries where they may leave over half a million people blind per year. The current study aims to boost the voriconazole antifungal efficiency via loading it as cubosomes (VZ-Cub) into hyaluronic acid and poloxamer-based ocular in situ gel. VZ-Cub were fabricated applying Box-Behnken design and employing phytantriol, poloxamer F127, and VZ amounts as independent variables. The produced nano vesicles were evaluated for the dependent variables of particle size (PS), entrapment efficiency (EE%), and transcorneal steady-state flux (Jss) of the VZ, and, the obtained optimal VZ-Cub was loaded into an in situ gel base to enhance its ocular residence time. The in situ gel formulation was tested for its gelation temperature, drug release behavior, transcorneal permeation effects, and antifungal activity. The optimized VZ-Cub consisted of 100 mg of phytantriol, 60 mg of poloxamer F127, and 21 mg of VZ. This formulation led to a minimum PS of 71 nm, an EE% of 66%, Jss value of 6.5 µg/(cm2·min), and stability index of 94 ± 2%. The optimized VZ-Cub-loaded in situ gel released 84% VZ after 12 h and yielded a 4.5-fold increase in drug permeation compared with the VZ aqueous dispersion. The antifungal activity, which was obtained by measuring the fungal growth inhibition zones, revealed that the VZ-Cub-loaded in situ gel formulation had a 3.89-fold increase in antifungal activity compared with the VZ dispersion. In summary, an ocular in situ gel loaded with VZ-Cub could be an effective novel nano-paradigm with enhanced transcorneal permeation and antifungal properties.

Effect of Multi-function Disintegrator Grinding on the Particle Size of Garcinia indica and Garcinia cambogia Rind Powder

Ultra-fine formulations edible dried fruit rind material provides a vast range of opportunities for the development of new products and applications in the food systems. The Garcinia indica and Garcinia cambogia, both species have a range of uses from culinary to healthcare applications. The dried rind of both species was attempted to study size and proportion of ultra-fine powder formed using Multi-function disintegrator as a function of different durations of grinding. The particle size and relative proportions were assessed using Zetasizer dynamic light scattering apparatus. A set of three major peaks in each sample was analyzed for particle size and intensity. In G. indica the result in peak1 for size and intensity, the minimum size of particle recorded was 175.8 nm from the sample ground 60 minutes. In G. cambogia minimum particle size recorded was 461.01nm from the sample ground for 60 minutes. The different particle sizes ranging from 48.13 nm to 3705.63 nm was recorded in powder resulting from different durations of grinding at full speed of the disintegrator. The results suggested that samples ground for longer duration in a simple particle disintegrator could accumulate ultra-fine particles in both G. indica and G. cambogia rind samples.

Physicochemical Properties and in vitro Digestibility of Myofibrillar Proteins From the Scallop Mantle (Patinopecten yessoensis) Based on Ultrahigh Pressure Treatment.

The utilization of myofibrillar proteins (MPs) from the scallop mantle was limited due to its poor digestibility in vitro. In this study, structural properties and in vitro digestibility of MP were evaluated after modified by ultra-high pressure (UHP) at different pressures (0.1, 100, 200, 300, 400, and 500 MPa). The results showed that high pressure could significantly increase the ordered structure content like α-helix, inhibit the formation of disulfide bonds, and decrease surface hydrophobicity. Moreover, MP possessed the optimal solubility and in vitro digestibility properties at 200 MPa due to the minimum particle size and turbidity, relatively dense and uniform microstructure. The results indicated that the UHP treatment was an effective method to improve the digestibility of MP from scallop mantle and lay a theoretical basis for the functional foods development of poor digestion people and comprehensive utilization of scallop mantles.

Fabrication of edible solid lipid nanoparticle from beeswax/propolis wax by spontaneous emulsification: Optimization, characterization and stability

In the current study, the production and characterization of novel solid lipid nanoparticles (SLNs) using safe/low-cost natural beeswax (BW) and propolis wax (PW) and by the simple and inexpensive assay of spontaneous emulsification were studied. To fabricate SLNs, the optimum levels of surfactant/oil ratio (SOR), stirring speed, and time were obtained based on minimum particle size (PS) and polydispersity index (PDI). Therefore, the optimal conditions to produce PW and BW nanoparticles were SOR of 1.26 and 2 under stirring speed of 1050 rpm for 20 min, leading to PS of 21.9 and 23.2 nm, respectively. The contact angle of 73.7° and 62.9° for BW and PW SLNs respectively, showed suitable hydrophilicity to stabilize oil-in-water (O/W) Pickering emulsions. Temperatures over 70 °C led to a drastic increment of PS in both types of SLNs. Upon nanoparticles drying, the utilization of cryoprotectants could cause less aggregation and better reconstitution.

Evaluation of the prevalence of stomach ulcers in slaughtered pigs in a Swiss ­abattoir

The development of gastric ulcers in pigs has various reasons. In Switzerland, the last survey on the prevalence of gastric ulcers and possible risk factors was performed in 2005. We aimed to reassess gastric ulcers prevalence today, in 2021. A total of 1005 stomachs from fattening pigs from 136 batches and around 87 herds were evaluated at a Swiss abattoir. The Pars oesophagea of the stomach was scored from 0=healthy to 10=severe ulceration and strictures. Scores were compared between pigs produced under the labels «Integrierte Produktion Schweiz» (IPS, n=242 stomachs, 18 farms) and «Qualitätsmanagement-Schweizerfleisch» (QM, n=649, 58 farms) and others (n=114). The results showed a prevalence of 27,2 % mild mucosal changes (Scores 1-3), 14,9 % moderate mucosal changes (Scores 4-6) and 19,1 % severe mucosal changes (Scores 7-10). Only 38,8 % of the stomachs were rated 0 and thus considered healthy. Compared to the results from 2005, there is no difference concerning the lowest scores (0-2) and the highest scores (9-10). However, there was a shift from the medium scores (3-4) to higher scores (5-8). Stomach scores turned out to be herd specific. There were differences (p < 0,01) between labels, indicating that IPS pigs had less affected stomachs. Stomachs that were empty at slaughter showed higher scores (p < 0,001). The mean carcass weight of the pigs in the slaughter groups was negatively correlated (p < 0,05) to their median stomach score. Confiscations were not related to stomach scores. The results suggest that pig stomach health has not improved since 2005. The differences between labels seem to have resulted from different regulations prescribing a minimum particle size of enrichment material in IPS. The reasons for gastric ulcer development, including those on the individual herd within label, still have to be further clarified in order to allow targeted countermeasures. Given apparent farm-specificity, scoring of a limited number of stomachs per herd during the slaughter process could facilitate the establishment of a feedback scheme.

“TPGS surface modified bilosomes as boosting cytotoxic oral delivery systems of curcumin against doxorubicin resistant MCF-7 breast cancer cells”

The goal of this work was to design nude bilosomes (Bil) and D-alpha-tocopheryl polyethylene glycol succinate (TPGS) surface coated bilosomes as an oral delivery platform for improving the antitumor activity and poor oral permeability of Curcumin (CUR). Twelve different formulae were acquired from 31.22 factorial analysis considering different independent variables: bile salt type; Sodium taurocholate (STC) or Sodium cholate (SC) and weight percent; 1% or 5 % W/W, both at 2 levels respectively, while Span 60:Cholesterol ratio at 3 levels (1:1, 5:1, 9:1). Following optimization, the selected optimum formula was picked up based on the favorable minimum particle size (187.2 ± 2.2 nm), maximum zeta potential value (-41.3 ± 2.2 mV) and maximum entrapment efficiency (93.4 ± 5.1%) which was further coated with TPGS. The mean fluorescence intensity (MFI) of CUR permeated from the optimum TPGS-F7 and CUR-Bil (F7) formulae exhibited 6.6 and 3.4 folds increase respectively adopting ex-vivo duodenal permeation assay relative to that of CUR suspension. Moreover, the cellular uptake efficiency via the established Caco-2 cells revealed that the uptake of CUR was 61.9 ± 5.3% and 34.76 ± 0.61% from TPGS-F7 and CUR-Bil (F7) relative to the uptake efficiency of CUR suspension (7.4 ± 2.12%). Coherently, TPGS-CUR-Bil showed excellent response expressed in dominant reduction in IC50 value (2.8 ± 0.07 µg/ml) against multidrug resistant (MDR) tumors following 48 h incubation of Doxorubicin Resistant Breast Cancer (MCF-7/ADR) cell lines.

Preparation and Electromagnetic Absorption Properties of Fe73.2Si16.2B6.6Nb3Cu1 Nanocrystalline Powder.

In order to decrease and control electromagnetic pollution, absorbing materials with better electromagnetic wave absorption properties should be developed. In this paper, a nanocrystalline alloy ribbon with the composition of Fe73.2Si16.2B6.6Nb3Cu1 was designed and prepared. Nanocrystalline alloy powder was obtained by high-energy ball milling treatment. The effects of ball milling time on the soft magnetic properties, microstructure, morphology, and electromagnetic wave absorption properties of alloy powder were investigated. The results showed that, as time increased, α-(Fe, Si) gradually transformed into the amorphous phase, and the maximum saturation magnetization (Ms) reached 135.25 emu/g. The nanocrystalline alloy powder was flakelike, and the minimum average particle size of the powder reached 6.87 μm. The alloy powder obtained by ball milling for 12 h had the best electromagnetic absorption performance, and the minimum reflection loss RLmin at the frequency of 6.52 GHz reached −46.15 dB (matched thickness was 3.5 mm). As time increased, the best matched frequency moved to the high-frequency direction, and the best matched thickness decreased, while the maximum effective absorption bandwidth ΔfRL<−10 dB was 7.22 GHz (10.78–18 GHz).

Octenyl Succinic Acid Starch-Stabilized Vanilla Essential Oil Pickering Emulsion: Preparation, Characterization, Antioxidant Activity, and Storage Stability.

Applications for vanilla essential oil extracted from vanilla pods have been limited since the effective components of vanilla could be easily influenced by environmental factors, such as temperature, light, and oxygen, which hinder their effectiveness. In this study, vanilla essential oil was encapsulated in a Pickering emulsion with octenyl succinic acid starch (OSA—starch). The optimal process conditions for emulsion preparation were determined as 5% vanilla essential oil phase with 2.5% OSA—starch when they were ultrusonicated for 3 min at 470 W. Under these conditions, the minimum particle size was 0.456 μm, the oil droplets were completely encased by starch, and no new chemical bonds were formed. The smallest particle size was produced at a pH of 4 and 500 mM ion concentration. The antioxidant activity of the emulsion was greater than that of the pure vanilla oil at the same oil content. After 24 h storage, the antioxidant activity of the emulsion was enhanced, and the vanilla essential oil was slowly released in the emulsion. These results indicated that the vanilla essential oil encapsulated in a Pickering emulsion with octenyl succinic acid starch showed its tremendous potential for use in the food industry.

Preparation of nano-sized 6MgO–2Y2O3–ZrO2 powders by a combined co-precipitation and high energy ball milling process

Nanostructured ceramic materials doped with stabilizers have superior mechanical, chemical, and electrical properties. In this study, tetragonal zirconia stabilized by 6 mol% MgO and 2 mol% Y2O3 (t-6MgO–2Y2O3–ZrO2) nanopowders with quasi-spherical morphology, uniform particle size, and narrower grain size distributions were prepared by a combination process including two steps: namely co-precipitation and high-energy ball milling. The effect of ball milling time on ZrO2 crystal particles was investigated by characterizations including XRD, Raman, FT-IR, FEESM, BET, and TEM. With the increase of ball milling time, the average grain size of the powder showed a gradual decrease tendency, the particle size distribution changed from wide to narrow, the particle morphology tended to be spherical, and the specific surface area gradually increased. Under the optimized conditions (ball milling for 8 h, calcination temperature of 800 °C, and holding time of 2 h), the highly dispersed spherical nanopowders with a minimum particle size of 18.47 nm and an average particle size of 29.02 nm were obtained. These zirconium oxide nanopowders are suitable for the preparation of inorganic coatings, biomedical materials, catalyst materials, and other types of functional materials.

Preparation of curcumin-loaded liposome with high bioavailability by a novel method of high pressure processing

Curcumin has been incorporated for the development of new products with applicability in food, pharmaceutical and cosmetic fields in Asia, due to the traits of anti-oxidation and anti-inflammatory. In the application of food engineering, high-pressure processing (HPP) can destroy non-covalent bonds and use as a method to inactivate bacteria for extending the perseveration of food. Thus, this study focuses on a novel approach for the microencapsulation of curcumin by the combination of ethanol injection and HPP at the room temperature for stabilizing pure curcumin in aqueous solutions and in liposome. The results revealed that the most optimal curcumin-liposome was prepared by HPP at operational pressure of 200 MPa within 5 mins holding time to obtain the minimum particle size of 281.9 nm, encapsulation efficiency of 87.25% and polydispersity index (PDI) of 0.23. Particle size could reduce to nanoscale (70.65 nm) after 0.5% addition of Tween 80, but the encapsulation efficiency spontaneously decreased to 45.05%. It is an option to produce liposome with nanosize and uniform distribution for the consideration of high drug delivery. Conclusively, HPP process could not only effectively decrease particle size and PDI of liposome but also efficiently sterilize bacteria around concentration of 103 CFU/g.

Biogenic synthesis of gold nanoparticles using Artemia urumiana extract and five different thermal accelerated techniques: fabrication and characterization.

Artemia urumiana is bisexual population of the Lake Urmia of Iran. Its biomass was freeze dried and using its lyophilized powder, hydro-alcoholic extract was prepared and utilized in gold nanoparticles (Au NPs) synthesis. Six different Au NPs fabrication methods namely: microwave heating, hydrothermal, ultraviolet (UV) irradiation, ultrasonication, common heating using conventional heating, and self-assembling were utilized for Au NPs synthesis using A.urumiana extract. Gas chromatography analysis indicated that the prepared extract were contained numerous fatty acid methyl esters such as Hexadecanoic acid methyl ester. Results indicated that the formed NPs using heater and stirrer, and UV irradiation had minimum particle size of 25 and 94nm, respectively. However, as compared to the formed Au NPs using heater and stirrer technique, UV irradiation fabricated Au NPs with high zeta potential value of-32.5mV and small polydispersity value of 0.310. Results also demonstrated that the synthesized Au NPs using heater and stirrers, and UV irradiation had highest antioxidant activities of 13.7 and 11.9%, and bactericidal effects against Escherichia coli and Staphylococcus aurous bacteria strains, as compared to other fabricated Au NPs using other methods. There were insignificant (p>0.05) differences between these two attributes of the formed Au NPs.

Characteristics and distribution of microplastics in shoreline sediments of the Yangtze River, main tributaries and lakes in China-From upper reaches to the estuary.

Microplastics (MPs) pervade the environment and increasingly threaten both natural ecosystems and human health. In this study, we investigated MP particle concentrations in sediment samples collected from 54 sites along the banks of the YangtzeRiver and its major tributaries and on lakeshores. The main polymer types found in the samples were polypropylene (PP), polystyrene (PS) and polyethylene (PE). MP particle abundance in the various types of locations was 35-51,968 particles/kg dry weight (d.w.) on the banks of the main river, 52-1463 particles/kg (d.w.) on the banks of tributaries and 2574-23,685 particles/kg (d.w.) on lakeshores. Correlation between MP abundance and mean annual runoff of each upstream tributary was significant, which suggests that increased runoff brings more microplastic waste to streambank sediments. The most common shape of MP particles in all upstream samples was flake, and in downstream samples it was foam. Small microplastic particles (< 0.50mm) were predominant at all sites in this study, and the minimum particle size in samples from the Yangtze river banks was 0.065mm. Average abundance of MP particles on the shores of the source lake was 9069 particles/kg around the inlet but only 866 particles/kg around the outlet; the difference was due to interception associated with sedimentation and precipitation in the lake. Our study represents the large-scale study of MPs contamination in sediment along the Yangtze River and provides important data regarding the accumulation and distribution of MPs in shoreline sediments of the upper, middle and lower reaches of the Yangtze River, main tributaries and lakes in China.

Improving the quality of mandarin juice using a combination of filtration and standard homogenization

Cloud loss and pulp precipitation are serious quality defects of mandarin juice (MJ) which brake on industrialization and need to be overcome by developing stabilization process. Therefore, filtration (FT) and standard homogenization (SH) on improving the cloud stability of MJ and minimizing the loss of major qualities were investigated. The FT-SH combined treatment effectively decreased the minimal particle size below 15 μm and sedimentation rate by 17.30%–74.40%, and increased the cloud value from 7.97% to 332.57%, results in more uniformity and cloud stability of MJ. Moreover, FT reduced the pectin methylesterase (PME) activity by 34.19%–50.96%, browning (ΔE∗ < 3), free and bound phenol contents (27.81% and 59.13%), and aroma intensity (p < 0.05). SH released the free phenols from bound phenols association with cloudiness. The optimum stabilization condition was considered as the 100-mesh + 20 MPa that was obviously improved the cloudiness and minimizing the color, polyphenol and aroma loss.

Effect of different mills on the physical and flow properties of selected black bean flour particle size fractions

AbstractBackground and ObjectivesParticle size and shape can influence inherent flour properties and eventually the quality of the finished food product. The objective of this study was to determine the effect of mill type on the physical and flow properties of selected particle size fractions of black bean flour.FindingsParticle shape differed with mill type and particle size. Disc mill and stone mill produced flour particles with lower circularity and greater elongation than did hammer mill, cyclone mill, and centrifugal mill. Greater particle elongation with a stone mill and disc mill is attributed to compression/shear size‐reduction forces applied to the particles trapped between the rotating/nonrotating stones or discs. Particle circularity increased with an increased particle size, which was reflected by a strong positive correlation between circularity and particle size (r = .93, n = 5) while elongation value was negatively correlated with average minimum particle size (r = −.90, n = 5). Particle circularity had a negative correlation of r = −.93, n = 30; r = −.81, n = 30; r ≈ −.95, n = 30; r = −.94, n = 30 with L*, angle of repose, angle of slide, and compact bulk density, respectively.ConclusionsMill type and particle size interaction significantly affected the physical and flow properties of selected particle size fractions of black bean flour. The results indicate that the large black bean particles were more circular and compact and less convex and elongated compared with small particles.Significance and NoveltyThese findings indicate that mill type affects not only particle size but also particle shape, both of which can affect the flow and functional processing properties of black bean flour.

QbD Supported Optimization of the Alginate-Chitosan Nanoparticles of Simvastatin in Enhancing the Anti-Proliferative Activity against Tongue Carcinoma.

The goal of the current study is to develop a chitosan alginate nanoparticle system encapsulating the model drug, simvastatin (SIM-CA-NP) using a novel polyelectrolytic complexation method. The formulation was optimized using the central composite design by considering the concentrations of chitosan and alginate at five different levels (coded as +1.414, +1, 0, −1, and −1.414) in achieving minimum particle size (PS-Y1) and maximum entrapment efficiency (EE-Y2). A total of 13 runs were formulated (as projected by the Design-Expert software) and evaluated accordingly for the selected responses. On basis of the desirability approach (D = 0.880), a formulation containing 0.258 g of chitosan and 0.353 g of alginate could fulfill the prerequisites of optimum formulation in achieving 142.56 nm of PS and 75.18% EE. Optimized formulation (O-SIM-CAN) was further evaluated for PS and EE to compare with the theoretical results, and relative error was found to be within the acceptable limits, thus confirming the accuracy of the selected design. SIM release from O-SIM-CAN was retarded significantly even beyond 96 h, due to the encapsulation in chitosan alginate carriers. The cell viability study and Caspase-3 enzyme assay showed a notable difference in contrast to that of plain SIM and control group. All these stated results confirm that the alginate-chitosan nanoparticulate system enhanced the anti-proliferative activity of SIM.

Preparation of diene-based nanoparticles by semibatch microemulsion polymerization and their catalytic hydrogenation

Poly(acrylonitrile-co-butadiene) nanoparticles were synthesized by semibatch microemulsion polymerization. The microstructure of the polymers was characterized by 1H NMR and FT-IR. The particle size of the nitrile butadiene rubber (NBR) latex could be well controlled by reaction temperature, surfactant concentration, and feeding time of monomer. The minimum particle size of 34.2 nm could be achieved by using the surfactant/monomer mass fraction of 7.9 wt%. The latex can be directly catalyzed for hydrogenation using Wilkinson's catalyst (RhCl(PPh3)3) and second generation Grubbs catalyst (Grubbs II), respectively. The hydrogenated products (HNBR) with a degree of hydrogenation above 95 mol% were obtained. The fast rate of hydrogenation demonstrates the unique advantages of small particle size.

Screening and prioritization of nano- and microplastic particle toxicity studies for evaluating human health risks – development and application of a toxicity study assessment tool

Concern regarding the human health implications that exposure to nano- and microplastic particles (NMPs) potentially represents is increasing. While there have been several years of research reporting on the ecotoxicological effects of NMPs, human health toxicology studies have only recently emerged. The available human health hazard data are thus limited, with potential concern regarding the relevance and reliability for understanding the potential human health implications. In this study we develop and apply a NMP toxicity screening assessment tool (NMP-TSAT) for evaluating human health effects studies against a suite of quality assurance and quality control (QA/QC) criteria for both in vivo and in vitro studies. A total of 74 studies representing either inhalation or oral exposure pathways were identified and evaluated. Assessment categories include particle characterization, experimental design, and applicability for risk assessment; with critical and non-critical criteria organized to allow screening and prioritization. It is observed that the majority of studies evaluated using the NMP-TSAT have been performed on monodisperse particles, predominately spheres (≈60%), consisting of polystyrene (≈46%). The majority of studies have tested particles < 5 μm, with a minimal particle size of 10 nm and a maximum particle size of about 200 μm. The total assessment score (TAS) possible for in vivo studies is 52, whereas for in vitro studies it is 46, which is based on receiving a maximum score of 2 against 26 and 23 criteria, respectively. The evaluated TAS ranged from between 12 and 44 and 16–34, for in vivo and in vitro studies, respectively. Given the challenges associated with prioritizing studies based on ranking them according to their TAS we propose a Tiered approach, whereby studies are initially screened based on how they score against various critical criteria, which have been defined for their relevance for assessing the hazards and risks for human health. In this instance, studies that score a minimum of ‘1’ against each of the critical criteria, regardless of how they rank according to their TAS, are prioritized as part of a Tier 1 screening and prioritization phase, which would then be followed by an expert evaluation, representing a Tier 2 level of assessment. Using this approach we identify 10 oral ingestion and 2 inhalation studies that score at least 1 against all critical criteria. Lastly, several key observations for strengthening future effects studies are identified, these include a need for the generation and access to standard reference materials representative of human exposure to NMPs for use in toxicity test systems and/or the improved characterization and verification of test particle characteristics, and the adoption of study design guidance, such as recommended by OECD, when conducting either in vivo inhalation or oral ingestion toxicity tests.