Migration Time Reproducibility Research Articles

On-line sample preconcentration using field-amplified stacking injection in microchip capillary electrophoresis.

Previous reports describing sample stacking on microchip capillary electrophoresis (microCE) have regarded the microchip channels as a closed system and treated the bulk flow as in traditional capillary electrophoresis. This work demonstrates that the flows arising from the intersection should be investigated as an open system. It is shown that the pressure-driven flows into or from the branch channels due to bulk velocity mismatch in the main channel should not be neglected but can be used for liquid transportation in the channels. On the basis of these concepts, a sample preconcentration scheme was developed in a commercially available single-cross glass chip for microCE. Similar to field-amplified stacking injection in traditional CE, a low conductivity sample buffer plug was introduced into the separation channel immediately before the negatively charged analyte molecules were injected. The detection sensitivity was improved by 94-, 108-, and 160-fold for fluorescein-5-isothiocyanate, fluorescein disodium, and 5-carboxyfluorescein, respectively, relative to a traditional pinched injection. The calibration curves for fluorescein and 5-carboxyfluorescein demonstrated good linearity in the concentration range (1-60 nM) investigated with acceptable reproducibility of migration time and peak height and area ratios (4-5% RSD). This preconcentration scheme will be of particular significance to the practical use of microCE in the emerging miniaturized analytical instrumentation.

Chiral Separation of Synthetic Vicinal Diol Compounds by Capillary Zone Electrophoresis with Borate Buffer and b-Cyclodextrin as Buffer Additive

The investigation on capillary electrophoretic enantioseparation of six synthetic compounds containing vicinal diol groups has been undertaken to acquire the optimum conditions using native beta-cyclodextrin (beta-CD) as chiral selector and borate as a background electrolyte. The separation was carried out in an uncoated capillary (58.5 cm x 75 microm i.d., effective length 48.5 cm) and the effects of several important factors were investigated in detail. The results showed that beta-CD as a chiral selector exhibited good enantioselectivity and that the enantioseparation was greatly influenced by the structure of the diols, the borate concentration and the buffer pH. The optimum performance was obtained for the chiral vicinal diols under the conditions of 200 mM borate buffer of pH 9.8 containing 1.7% beta-CD at an applied voltage of 15 kV and a capillary temperature of 20 degrees C. Under the conditions, four diols were baseline separated with fast analysis time and the good theoretical plate numbers (above 10 x 10(4)) and favorable migration-time reproducibilities (RSDs below 3.0%) were obtained. The separation results were satisfactory.

High efficiency micellar electrokinetic chromatography of hydrophobic analytes on poly(dimethylsiloxane) microchips

This paper describes a simple method for the effective and rapid separation of hydrophobic molecules on polydimethylsiloxane (PDMS) microfluidic devices using Micellar Electrokinetic Chromatography (MEKC). For these separations the addition of sodium dodecyl sulfate (SDS) served two critical roles - it provided a dynamic coating on the channel wall surfaces and formed a pseudo-stationary chromatographic phase. The SDS coating generated an EOF of 7.1 x 10(-4) cm(2) V(-1) s(-1) (1.6% relative standard deviation (RSD), n = 5), and eliminated the absorption of Rhodamine B into the bulk PDMS. High efficiency separations of Rhodamine B, TAMRA (6-carboxytetramethylrhodamine, succinimidyl ester) labeled amino acids (AA), BODIPY FL CASE (N-(4,4-difluoro-5,7-dimethyl-4-bora-3a,4a-diaza-s-indacene-3-propionyl)cysteic acid, succinimidyl ester) labeled AA's, and AlexaFluor 488 labeled Escherichia coli bacterial homogenates on PDMS chips were performed using this method. Separations of Rhodamine B and TAMRA labeled AA's using 25 mM SDS, 20% acetonitrile, and 10 mM sodium tetraborate generated efficiencies > 100,000 plates (N) or 3.3 x 10(6) N m(-1) in <25 s with run-to-run migration time reproducibilities <1% RSD over 3 h. Microchips with 30 cm long serpentine separation channels were used to separate 17 BODIPY FL CASE labeled AA's yielding efficiencies of up to 837,000 plates or 3.0 x 10(6) N m(-1). Homogenates of E. coli yielded approximately 30 resolved peaks with separation efficiencies of up to 600,000 plates or 2.4 x 10(6) N m(-1) and run-to-run migration time reproducibilities of <1% RSD over 3 h.

Microchip Separations in Reduced-Gravity and Hypergravity Environments

Microfabricated fluidics technology, e.g., lab-on-a-chip devices, offers many attractive features for performing chemistry and biochemistry on space-based platforms. We have constructed a portable, battery-operated microfluidic platform that was tested under reduced gravity and hypergravity conditions that would be experienced in space flight and launch. This device consisted of a microchip, microchip holder, two 0-8-kV high-voltage power supplies, a high-voltage switch, a solid-state diode-pumped green laser, an optical train, a channel photomultiplier, and an inertial mass measurement unit all under the control of a laptop computer and powered by 10 D-cell alkaline batteries. The unit was tested on NASA's reduced gravity research aircraft at gravity levels that are relevant to NASA's intended use of bioreporter-based microchips for environmental monitoring of space and planetary environments on manned and unmanned spacecraft. Over the course of two flights, 834 fast electrophoretic separations of four amino acids were performed under a variety of gravitational environments including zero-g, Martian-g, lunar-g, and approximately 1.8-g. All separations were performed in less than 12 s and automatically analyzed. After correction with an internal migration standard, the migration time reproducibilities were all <1% relative standard deviation.

A sulfonated capillary that gives reproducible migration times for capillary zone electrophoresis and micellar electrokinetic chromatography

To obtain reproducible migration times and rapid analyses of analytes, sulfonate groups were chemically introduced to the inner wall of untreated fused-silica capillary with 2-(4-chlorosulfonylphenyl)ethyltrichlorosilane. The sulfonated capillary showed relatively constant electroosmotic mobility which was greater than that obtained by an untreated fused-silica capillary over the pH range studied (pH 2-9). In both CZE and MEKC, the RSDs of the migration times of analytes with the sulfonated capillary were less than 0.2% which were significantly lower than those obtained with an untreated fused-silica capillary (0.5-3.5%). When BGE were set at pH 7.0 for CZE and MEKC, the analysis times with the sulfonated capillary were about half those obtained with an untreated fused-silica capillary. These results indicate that the sulfonated capillary can provide highly reproducible and rapid analyses in CE.

Novel nonaqueous capillary electrophoresis separation and determination of bioactive flavone derivatives in Chinese herbs

Nonaqueous CE (NACE) coupled to UV detection is described for the separation and determination of bioactive flavone derivatives in Chinese herbs extraction. After optimization of electrophoresis parameters, including the electrolyte nature and the organic solvent composition, a reliable separation of the analytes in an ACN/methanol (60:40, v/v) mixture containing 80 mM Tris and 10 mM sodium cholate was performed. The detection was performed at 254 nm. Method performances, including migration time and peak area reproducibility, linearity, sensitivity, and accuracy, were evaluated. The method was applied to determine bioactive flavone derivatives in seven Chinese herbs.

Poly(ethylene oxide) facilitates the characterization of an affinity between strongly basic proteins with DNA by affinity capillary electrophoresis

In order to study kin17 protein-DNA affinity, we have developed a fast and reproducible capillary electrophoresis (CE) analysis of a strongly basic protein: kin17 protein, using a nonpermanent coating based on poly(ethylene oxide) (PEO) to avoid adsorption of kin17. The coating procedure was optimized to provide a residual and stable electroosmotic flow (EOF = 5 x 10(-5) cm(2)/V x s), exhibiting RSD of 0.3% and excellent long-term stability. Good intraday and interday reproducibility of kin17 migration times (0.8 and 0.3% relative standard deviation (RSD), respectively) enabled us to consider that the recovery percentage obtained for kin17 protein was satisfactory (79%). The potential of this PEO-based coating procedure was evaluated for affinity CE method in order to study the affinity of kin17 protein for two single-stranded DNA (ssDNA) models: polydeoxyadenylic acid and polydeoxycytidilic acid (pdA and pdC). Binding constants (1.5 x 10(7) +/- 17% and 1.7 x 10(7) + 25%M(-1)) were evaluated assuming a 1:1 affinity between kin17 and pdA or pdC, respectively.

Enantioselective separation of rivastigmine by capillary electrophoresis with cyclodextrines

Different β-cyclodextrines (β-cyclodextrin, heptakis (2,3,6-tri- O-methyl)-β-cyclodextrin, hydroxypropyl-β-cyclodextrin, and sulfated β-cyclodextrin) were investigated as additives for the enantioselective separation of the R-form from rivastigmine (( S)- N-ethyl-3-[(1-dimethyl-amino) ethyl]- N-methyl-phenyl carbamate), contained as impurity in this drug, which is used for the treatment of Alzheimer's disease. Electrophoresis was performed in an acidic background electrolyte (triethanolammonium phosphate, 75 mM, pH 2.5) with various concentrations of the additives. The electrophoretic mobilities measured are typical functions of the additive concentrations, with complex constants (obtained by fitting the appropriate binding curve on the data) ranging between about 180 and 770 M −1. Best separation was obtained with 7.5 mM β-cyclodextrin, with the R-enantiomer as impurity migrating before the main S-compound. Intra- and interday reproducibility ( n = 6 and 18, respectively) of migration time and peak area was in the low percentage range, linearity of the calibration line for the quantitation of the impurity in the range between 2.3 and 50 μg/ml, expressed by the linear correlation coefficient, was 0.9998. The limits of detection and quantitation, respectively, were 0.7 and 2.3 μg/ml, corresponding to 0.05 and 0.15%, m/m of the R- relative to the S-compound. Analysis can be carried out at 18 °C in less than 19 min.

Application of dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium in wall modification for capillary electrophoresis separation of proteins

A zwitterionic surfactant, dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium (C12H25N+(CH3)2CH2CHOHCH2SO3-), named dodecyl sulfobetaine (DSB), was used as a novel modifier to coat dynamically capillary walls for capillary electrophoresis separation of basic proteins. The DSB coating suppressed the electroosmotic flow (EOF) in the pH range of 3-12. At high DSB concentration, the EOF was suppressed by more than 8.8 times. The DSB coating also prevented successfully the adsorption of cationic proteins on the capillary wall. Anions, such as Cl-, Br-, I-, SO4(2-), CO3(2-), and ClO4-, could be used as running buffer modifiers to adjust the EOF for better separation of analytes. Using this dynamically coated capillary, a mixture of eight inorganic anions achieved complete separation within 4.2 min with the efficiencies from 24,000 to 1,310,000 plates/m. In the presence of ClO4- as EOF adjustor, the separation of a mixture containing four basic proteins (lysozyme, cytochrome c, alpha-chymotrypsinogen A, and myoglobin) yielded efficiencies of 204,000-896,000 plates/m and recoveries of 88%-98%. Migration time reproducibility of these proteins was less than 0.5% relative standard deviation (RSD) from run to run and less than 3.1% RSD from day to day, showing promising application of this novel modifier in protein separation.

Simultaneous determination of ten amphetamine designer drugs in human whole blood by capillary electrophoresis with diode array detection

In recent years, a number of new designer drugs have entered the illicit drug market. The methylenedioxyderivatives of amphetamine represent the largest group of designer drugs. This paper describes a method for screening for and simultaneously quantifying 10 2,5-methylenedioxy-derivatives of amphetamine and phenethylamine in human whole blood, using capillary electrophoresis (CE) with diode array detection (DAD). Using an aqueous pH 2.5 phosphate buffer, CE analysis gave peaks with good symmetry and reproducible migration times. Under these experimental conditions, the 10 amphetamines were resolved in 15 min and without interference from biological matrices (blood). Their identification by migration time was confirmed by their UV spectra recorded with a DAD (190-350 nm). The main advantages of the present method lie in its simplicity, clean and reliable extraction from human whole blood and simultaneous detection and quantification by CE-DAD. The applicability of the method was demonstrated by analysis of in vivo rat blood samples. The method was validated according to international guidelines.

Effect of Capillary Rinsing Protocol on the Reproducibility of Separation in Capillary Electrophoresis with Indirect UV Detection

Capillary electrophoresis (CE) with indirect UV detection is an interesting analytical method for the analysis of drugs and pharmaceuticals. Good and reproducible capillary quality is needed to develop robust methods and to facilitate method transfer in CE. It is widely accepted that preconditioning procedures are indispensable in capillary electrophoresis in order to achieve reproducibility of migration times and peak areas. In order to explore different aspects of this technique, a set of experiments were performed using vigabatrin as a model drug. The effects of capillary rinsing between each run was investigated using basic (NaOH 0.1 M) and acidic (phosphoric acid 0.1 M)-wash cycles. The results of 10 consecutive injection of the model drug after each of the two wash cycles, reveal that more reproducible results obtained when acid-wash cycle was performed as a capillary conditioning protocol. The higher pH changes during basic-wash cycle and its effects on the characteristics of the capillary inner surface were suggested as a source of greater variation between consecutive runs.

Hand-Held Microanalytical Instrument for Chip-Based Electrophoretic Separations of Proteins

The design, fabrication, and demonstration of a hand-held microchip-based analytical instrument for detection and identification of proteins and other biomolecules are reported. The overall system, referred to as muChemLab, has a modular design that provides for reliability and flexibility and that facilitates rapid assembly, fluid and microchip replacement, troubleshooting, and sample analysis. Components include two independent separation modules that incorporate interchangeable fluid cartridges, a 2-cm-square fused-silica microfluidic chip, and a miniature laser-induced fluorescence detection module. A custom O-ring sealed manifold plate connects chip access ports to a fluids cartridge and a syringe injection port and provides sample introduction and world-to-chip interface. Other novel microfluidic connectors include capillary needle fittings for fluidic connection between septum-sealed fluid reservoirs and the manifold housing the chip, enabling rapid chip priming and fluids replacement. Programmable high-voltage power supplies provide bidirectional currents up to 100 microAlpha at 5000 V, enabling real-time current and voltage monitoring and facilitating troubleshooting and methods development. Laser-induced fluorescence detection allows picomolar (10(-11) M) detection sensitivity of fluorescent dyes and nanomolar sensitivity (10(-9) M) for fluorescamine-labeled proteins. Migration time reproducibility was significantly improved when separations were performed under constant current control (0.5-1%) as compared to constant voltage control (2-8%).

Surface-Modified Poly(methyl methacrylate) Capillary Electrophoresis Microchips for Protein and Peptide Analysis

Polymeric materials have emerged as appealing alternatives to conventional inorganic substrates for the fabrication of microscale analytical systems; however, native polymeric surfaces typically require covalent modification to ensure optimum biocompatibility. 2-Bromoisobutyryl bromide was immobilized on poly(methyl methacrylate) (PMMA) substrates activated using an oxygen plasma. Atom-transfer radical polymerization was then performed to graft poly(ethylene glycol) (PEG) on the PMMA surface. PMMA microcapillary electrophoresis (muCE) devices made with the covalently modified surfaces exhibited substantially reduced electroosmotic flow and nonspecific adsorption of proteins on microchannel surfaces. Experiments using fluorescein isothiocyanate-conjugated bovine serum albumin indicated that both column efficiency and migration time reproducibility were 1 order of magnitude better with derivatized compared to untreated PMMA muCE chips. Fast, reproducible, and efficient separations of proteins and peptides were demonstrated using the PEG-grafted PMMA muCE chips. All analyses were completed in less than 60 s, and separation efficiencies as high as 5.2 x10(4) plates for a 3.5-cm-long separation channel were obtained. These results demonstrate the general applicability of surface-grafted PMMA microdevices for a broad range of protein analyses.

Enantiomeric analysis of rivastigmine in pharmaceuticals by cyclodextrin-modified capillary zone electrophoresis

Chiral separation method development is usually very time-consuming due to the diversity in chemical structures of pharmaceutical drug substances as well as the suitable separation conditions and the problem to choose the appropriate chiral selector. This paper shows capillary zone electrophoresis (CZE) which was developed for chiral separation of a basic compound – rivastigmine (RIV) using 30 cm × 50 μm i.d. polyacrylamide (PAA)-coated fused-silica capillary (effective length 20 cm), amine-modified phosphate buffer of pH 2.5 and sulfated-β-CD (S-β-CD) as chiral selector. Other selected native or derivatized cyclodextrins (CDs) were also tested: β-CD (5, 30 mM), carboxymethyl-β-CD (5, 30 mM), dimethyl-β-CD (15 mM), hydroxypropyl-β-CD (5, 30 mM), hydroxypropyl-α-CD (5, 30 mM) and hydroxypropyl-γ-CD (5, 30 mM). Complete enantiomeric separation of RIV was achieved at 20 kV, 18 °C and detection at 200 nm within 8 min with R.S.D. for the absolute migration time reproducibility of less than 2.1%. Rectilinear calibration range was 5.0–500.0 μM of each enantiomer ( r = 0.9994–0.9995). The CZE method proposed was used for the control of chiral purity of pharmaceutically active S-RIV and for the analysis of Exelon caps preparation.

A novel double coating for microemulsion electrokinetic chromatography with laser-induced fluorescence detection: as tested with amino acid derivatives

A novel double coating (DC) was developed for fast and reproducible microemulsion electrokinetic chromatography (MEEKC), as tested with separation and determination of amino acids using laser-induced fluorescence (LIF) detection after derivatization with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazol. The simple coating is a combination of a removable covalent layer and a dynamic SDS coating. Hexamethyldisilazane was utilized for the covalent layer that can be regenerated on-line. Compared with previous no-coating method, the analysis time was shortened; and the reproducibility of migration times was improved.

Optimization of ascorbic and uric acid separation in human plasma by free zone capillary electrophoresis ultraviolet detection

In this paper we propose a new fast free zone capillary electrophoresis method for the simultaneous determination of ascorbic acid (AA) and uric acid (UA) in human plasma. We investigated the effect of analytical parameters, such as concentration and pH of borate running buffer, cartridge temperature, and sample treatment, on resolution, migration times, corrected peak areas, and efficiency. A good separation was achieved using a 60.2-cm × 75-μm uncoated silica capillary and 100 mmol/L sodium borate buffer, pH 8, when metaphosphoric acid was employed as protein precipitant, in less than 4 min. These conditions gave a good reproducibility of migration times (CV 0.35 and 0.34%) and peak areas (CV 3.2 and 3.1%) for ascorbate and urate, respectively. The limit of detection was 0.5 mg/L for both analytes when the detection was performed at 254 nm for AA and at 292 nm for UA. We compared the present method with a validated capillary electrophoresis assay by measuring plasma urate and ascorbate in 32 normal subjects and the obtained data were analyzed by the Passing and Bablok regression.

Factors Affecting the Temporal Stability of Semipermanent Bilayer Coatings in Capillary Electrophoresis Prepared Using Double-Chained Surfactants

Surfactants such as didodecyldimethylammonium bromide (DDAB) adsorb onto fused-silica capillaries to form semipermanent bilayer coatings. However, such coatings must be regenerated between runs to maintain efficiency and reproducibility. In this paper, chemical and physical factors affecting the stability of DDAB coatings are investigated. Chemical factors such as ionic strength and the nature of the buffer anion (e.g., from acetate to phosphate), which decrease the critical micelle concentration of DDAB, improve the coating stability. Increasing buffer pH also increases the coating stability. Finally, reducing the capillary diameter and reducing the volume of buffer flushed through the capillary enhance the coating stability. Using 50 mM acetate, pH 5.0, in a 25-microm-i.d. capillary, cationic proteins were separated with efficiencies of 1.05 million plates/m and a run-to-run migration time reproducibility of 0.6-0.8% RSD for 10 successive runs without regeneration of the DDAB coating between runs.

Chiral separation of highly negatively charged enantiomers by capillary electrophoresis

The separation of two highly negatively charged enantiomeric organic disulfates containing two chiral centers was investigated by capillary electrophoresis using cyclodextrin based chiral selectors added to the run buffer. The optimum separation for the enantiomers was achieved in less than 3 min at 25 °C with a run buffer of 10 mM glycine pH 2.4 and 5 mM QA-β-CD, which is a positively charged quaternary ammonium β-cyclodextrin derivative. The method resulted in baseline resolution, excellent linearity, and highly reproducible migration times allowing facile evaluation of the enantiomeric purity of the individual isomers. Detection limits for the enantiomeric pair were determined to be 0.3 ng/μl (S/N=3). The nature of the selector–enantiomer interaction and a quantitative measurement of the apparent stability constants that governed chiral discrimination of the enantiomers with QA-β-CD were also investigated by UV-Vis spectroscopy and electrospray ionization mass spectrometry.

Mixed cationic/anionic surfactants for semipermanent wall coatings in capillary electrophoresis.

Mixtures of the cationic surfactant cetyltrimethylammonium bromide (CTAB) with the anionic surfactant sodium dodecyl sulfate (SDS) form more stable coatings in fused-silica capillaries than CTAB alone. The reversed electroosmotic flow (EOF) generated by CTAB/SDS mixtures remains stable for over 80 min after removal of the surfactants from the buffer. Enhanced stability (relative to CTAB alone) was found even when the ratio of SDS to CTAB was as low as 1%. This greater coating stability is attributed to the structural transition from adsorbed micelle to bilayer, which is induced by addition of SDS. Separation of a mixture of basic proteins yielded efficiencies of 364 000-562 000 plates/m and recoveries ranging from 85% to 98%. Migration time reproducibility was less than 0.9% relative standard deviation (RSD) from run to run and less than 2.6% RSD from day to day.

Determination of Ochratoxin A in small volumes of human blood serum

A new simple and rapid method for analysing Ochratoxin A (OTA) in small volumes of human blood serum using capillary zone electrophoresis coupled to laser-induced fluorescence is described. The clean-up procedure solely consists of a double extraction step. To improve the reproducibility of migration times and quantification, two internal standards were used. The limit of detection was 0.55 ng/ml, with a linear range of 1–100 ng/ml of OTA in spiked human blood serum. The method is used to rapidly screen suspected patients.