Transport Of Microplastics Research Articles

The effects of large roughness elements on the in-stream transport and retention of polystyrene microplastics

The mechanisms controlling transport and retention of microplastics (MPs) in riverine systems are not understood well. We investigated the impact of large roughness elements (LREs) on in-stream transport and retention of the ubiquitous polystyrene-microplastics (PS-MPs). Scaled experiments were conducted with and without LREs under various shear Reynolds numbers (Re*) in an ecohydraulics flume. Our results, for the first time, demonstrated a clear dependence of the MPs’ velocity on Re* in LREs-dominated channel. Two distinct regimes and thresholds were identified: lower Re* (≤ 15,000) regime corresponding to higher velocities of MPs ({U}_{MPs}^{*}> 0.45), and higher Re* (> 15,000) to lower {U}_{MPs}^{*} (< 0.45). The presence and higher density of LREs increased Re*, decreased {U}_{MPs}^{*}, and enhanced the PS-MPs capture. The LREs-generated turbulence kinetic energy (TKE) was found to be a good predictor of PS-MPs transport and retention rates, indicating the effectiveness of LREs in retaining PS-MPs in streams and rivers.

Vertical Differentiation of Microplastics Influenced by Thermal Stratification in a Deep Reservoir.

Microplastics (MPs) are an emerging environmental concern. However, vertical transport of MPs remains unclear, particularly in deep reservoirs with thermal stratification (TS). In this study, the vertical variation in MP organization, stability, migration, and the driving factors of the profile in a deep reservoir were comprehensively explored. This is the first observation that TS interfaces in a deep reservoir act as a buffer area to retard MP subsidence, especially at the interface between the epilimnion and the metalimnion. Interestingly, there was a size-selection phenomenon for MP sinking. In particular, the high accumulation of large-sized MPs (LMPs; >300 μm) indicated that LMPs were more susceptible to dramatic changes in water density at the TS interfaces. Furthermore, simultaneous analysis of water parameters and MP surface characteristics showed that the drivers of MP deposition were biological to abiotic transitions during different layers, which were influenced by algae and metals. Specifically, scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy and microscopic Fourier transform infrared analyses implied that the occurrence of metals on the MP surface can promote MP deposition in the hypolimnion. Our findings demonstrated that TS significantly influenced the MP fate in deep reservoirs, and the hotspot of MP exposure risk for vulnerable benthic organisms on the reservoir floor deserves more attention.

Amount and characteristics of microplastic and organic matter in wind-blown sediment at different heights within the aeolian sand saltation layer

Soils of croplands especially where plastic film mulch is commonly applied, are normally contaminated by Microplastics (MPs). Microplastics can threaten air quality, food and water health, as well as human health by wind erosion processes. In this research, we investigated MPs collected in four wind erosion events at sampling heights between 0 and 60 cm in typical semiarid farmlands in northern China that employ plastic film mulch. Height distribution and enrichment heights of the MPs were measured. The results revealed that the average amounts of MPs for 0–20 cm, 20–40 cm and 40–60 cm sampling heights were 868.71 ± 249.21, 799.87 ± 271.25, 1102.54 ± 317.44 particles kg−1. The average enrichment ratios of MPs for the different heights were 0.89 ± 0.54, 0.85 ± 0.56, 1.15 ± 0.73. Height distribution of MPs was combined affected by shape (fiber and non-fiber) and size of MPs, wind speed and soil aggregate stability. The amount of fibers approximately <4 mm in size and non-fibers <2 mm in size increased with sampling height, while both shapes of larger MPs than these two sizes was almost independent of the sampling height. Enrichment ratios of microfibers were positively related to wind speed but negatively related to soil aggregate stability at each sampling height. The results revealed that although MPs have similar density to organic matter (OM), the MPs’ amount and enrichment were independent of height but the OM content and enrichment ratios increased with height. These results suggested that more attention should be paid to the exploration of the influence of higher sampling heights (>60 cm) on the distribution of MPs in the future and the MPs characteristics for different sampling heights require carefully parameterization in detailed models of atmospheric MPs transport by wind erosion.

Effects of neonicotinoid insecticides on transport of non-degradable agricultural film microplastics

Mulch film microplastics (MPs) could act as a vector for agricultural chemicals due to their long-term presence in farmland environments. As a result, this study focuses on the adsorption mechanism of three neonicotinoids on two typical agricultural film MPs, polyethylene (PE) and polypropylene (PP), as well as the effects of neonicotinoids on the MPs transport in quartz sand saturated porous media. The findings revealed that the adsorption of neonicotinoids on PE and PP was a combination of physical and chemical processes, including hydrophobic, electrostatic and hydrogen bonding. Acidity and appropriate ionic strength (IS) were favorable conditions for neonicotinoid adsorption of on MPs. The results of column experiments showed that the presence of neonicotinoids, particularly at low concentrations (0.5 mmol L−1), could promote the transport of PE and PP in the column by improving the electrostatic interaction and hydrophilic repulsion of particles. The neonicotinoids would be adsorbed on MPs through hydrophobic action preferentially, whereas excessive neonicotinoids could cover the hydrophilic functional groups on the surface of MPs. Neonicotinoids reduced the response of PE and PP transport behavior to pH changes. 0.005 mol L−1 NaCl ameliorated the migration of MPs by increasing their stability. Because of its highest hydration ability and the bridging effect of Mg2+, Na+ had the most prominent transport promoting effect on PE and PP in MPs-neonicotinoid. This study shows that the increased environmental risk caused by the coexistence of microplastic particles and agricultural chemicals is unneglectable.

Significance of Microplastics in Agricultural Soil

Microplastics (MPs) can effect terrestrial ecosystems (approximately 20% of the pollution rate), but it also strongly effect aquatic ecosystems, with an estimate of 80% of the marine pollution. In the present time, we are facing the fact that more and more agricultural land has been contaminated with MPs. Underground transport of MPs in the soil occurs through bioturbation with the help of plant roots and soil fauna, as well as plowing, soil cultivation, crop harvesting, water infiltration, etc. Literature data stated that the concentration of MPs in terrestrial ecosystems is multiple times higher than in the ocean, and due to this fact, the United Nations Environment Programme appealed for more research studies on the assumed effects.

Modeling Microplastic Transport in the Marine Environment: Testing Empirical Models of Particle Terminal Sinking Velocity for Irregularly Shaped Particles.

Microplastic (mP) pollution has been indicated as an area of concern in the marine environment. However, there is no consensus on their potential to cause significant ecological harm, and a comprehensive risk assessment of mP pollution is unattainable due to gaps in our understanding of their transport, uptake, and exchange processes. This research considers drag models that have been proposed to calculate the terminal settling velocity of regularly and irregularly shaped particles to assess their applicability in a mP modeling context. The evaluation indicates three models that predict the settling velocity of mPs to a high precision and suggests that an explicit model is the most appropriate for implementation in a mP transport model. This research demonstrates that the mP settling velocity does not vary significantly over time and depth relevant to the scale of an ocean model and that the terminal settling velocity is independent of the initial particle velocity. These findings contribute toward efforts to simulate the vertical transport of mPs in the ocean, which will improve our understanding of the residence time of mPs in the water column and subsequently their availability for uptake into the marine ecosystem.

Oxalic-activated minerals enhance the stabilization of polypropylene and polyamide microplastics in soil: Crucial roles of mineral dissolution coupled surface oxygen-functional groups

Low-molecular-weight organic acids (LMWOAs) prevalent in soil environments may influence the transport, fate, and orientation of microplastics (MPs) by mediating mineral interfaces. Nevertheless, few studies have reported their impact on the environmental behavior of MPs in soil. Here, the functional regulation of oxalic at mineral interfaces and its stabilizing mechanism for MPs were investigated. The results showed that oxalic drove MPs stability onto minerals and new adsorption pathways, which are dependent on the bifunctionality of minerals induced by oxalic acid. Besides, our findings reveal that in the absence of oxalic acid, the stability of hydrophilic and hydrophobic MPs on kaolinite (KL) mainly displays hydrophobic dispersion, whereas electrostatic interaction is dominant on ferric sesquioxide (FS). Moreover, the amide functional groups ([NHCO]) of PA-MPs may have positive feedback on the stability of MPs. In the presence of oxalic acid (2–100 mM), the MPs stability efficiency and property onto minerals were integrally increased in batch studies. Our results demonstrate the oxalic acid-activated interfacial interaction of minerals via dissolution coupled O-functional groups. Oxalic-induced functionality at mineral interfaces further activates electrostatic interaction, cation bridge effect, hydrogen forces, ligand exchange and hydrophobicity. These findings provide new insights into the regulating mechanisms of oxalic-activated mineral interfacial properties for environmental behavior of emerging pollutants.

Breathing plastics in Metro Manila, Philippines: presence of suspended atmospheric microplastics in ambient air.

Microplastics (< 5mm) have lately been identified in the atmosphere of urban, suburban, and even distant places far from plastic particle areas, suggesting the possibility of long-distance atmospheric transport of microplastics. However, the occurrence, fate, transmission, and effects of these suspended atmospheric microplastics (SAMPs) are all currently unknown in the Philippines. This study investigated the presence of suspected microplastic in the atmosphere of sixteen cities and one municipality of Metro Manila, Philippines. Sampling was conducted using a respirable dust sampler mounted with a Whatman GF/C filter paper at an intake flow rate of 1.4 L/min with Whatman GF/C filter paper. Results reveal that all seventeen sampling areas have the presence of SAMPs. A total of 155 SAMPs were found and confirmed in Metro Manila, with the highest concentration in Muntinlupa City and Mandaluyong City (0.023 SAMP/NCM). Fourteen SAMP types were identified across the sampling areas, ⁓74% with polyester. This study is the first record of the presence of microplastics suspended in the ambient air in the Philippines. It is estimated that an adult person in Metro Manila has the potential to inhale (5-8 per minute, normal minute ventilation) about 1 SAMP if exposed for about 99.0 to 132h. Further studies should be done to evaluate the fate and health effects of these SAMPs in Metro Manila's setting.

Identification of factors influencing the microplastic distribution in agricultural soil on Hainan Island

Microplastics (MPs) are ubiquitous in agricultural soils, but to what extent and how environmental factors determine the source and fate of MPs in agricultural soils is not clear. In this study, Hainan Island, which has different climatic conditions, altitudes, and land uses across the island, was selected to investigate the MPs abundance and the shape, size, color, and polymer type of the MPs in agricultural soils. The main focus was on the role of land use type and the identification of environmental influencing factors. The results showed that MPs were detected in all the soil samples across the island, with an abundance range of 20 to 6790 items kg−1 and an average of 417 items kg−1. Fragments (46.8 %), MPs smaller than 0.5 mm (37.8 %), black MPs (48.3 %), and polypropylene MPs (56.8 %) were observed as the dominant MPs species. Significantly higher MPs abundance was found in mulched arable land, and higher contents of fibers and fragments were observed in woodland and paddy lands, respectively. With correlation and redundancy analyses, soil pH, soil organic matter content, and average annual temperature were found to be the main factors influencing the biotic/abiotic fragmentation of MPs. The regional population density, including tourism represented by the night light index, affects the input process of MPs. MPs transport and deposition were found to be affected by altitude, annual precipitation, and soil moisture content. This study represents the first large-scale study of MPs contamination in island agricultural soils and provides important data on the distribution, transport, and fate of MPs.

Quantifying environmental emissions of microplastics from urban rivers in Melbourne, Australia

This study aims to understand the amount and type of microplastics flowing into Port Phillip Bay from urban rivers around Melbourne. Water samples were collected from the Patterson, Werribee, Maribyrnong, and Yarra Rivers, which contribute 97 % to the total flow into Port Phillip Bay. On average, the rivers contained a mean of 9 ± 15 microplastics/L and ranged from 4 ± 3 microplastics/L (Patterson) to 22 ± 11 microplastics/L (Werribee). Of the eight polymers investigated, polyamide and polypropylene were the most frequently detected polymers. Using the mean concentration of each river, the flow of microplastics into Port Philip Bay was estimated to be 7.5 × 106 microplastics per day and 3.7 × 1010 microplastics per year. To fully understand the fate and transport of microplastics into Port Phillip Bay, this study would be the foundation for a more in-depth investigation. Here, further samples will be collected at more points along the river and at the midpoint of each season.

Higher concentrations of microplastics in runoff from biosolid-amended croplands than manure-amended croplands

Land-applied municipal biosolids, produced from municipal wastewater treatment sludge, contributes to microplastics contamination in agroecosystems. The impacts of biosolids on microplastic concentrations in agricultural soil have been previously investigated, however, the potential for microplastics transport from biosolid-amended croplands has not been previously quantified. In this study, manure and biosolids were applied to field plots, runoff was collected following natural precipitation events and the potential of bacterial biofilm to grow on different microplastic morphologies was investigated. Higher concentrations of microplastics were detected in runoff from plots with land-applied biosolid in comparison with manure-amended and control plots. Fibers and fragments were the most frequently detected plastic morphologies in runoff, correlated with their decreased surface roughness. The potential of biosolids to contribute to microplastic contamination to U.S. surface waters was quantified which is among the first to quantify the potential for nonpoint source microplastic contamination of surface waters adjacent to agricultural production areas.

Insights on experimental methodologies and theoretical models for microplastics transport in soils and sediments based on meta-analysis

Insights on experimental methodologies and theoretical models for microplastics transport in soils and sediments based on meta-analysis

Entrainment and horizontal atmospheric transport of microplastics from soil

Soils are an important source of microplastics (MPs) to the atmosphere but the fluxes and mechanisms involved in MPs entrainment are not well understood. In the present study, a series of horizontally aligned sediment traps have been deployed at different heights within 1 m above the ground for a two-month period at various locations in an arid region (Sarakhs, Iran). MPs were isolated from sediments and were quantified and characterised according to size, colour, shape and polymer composition by established techniques. Most MPs were <250 μm in length, fibres were the most important shape, black and blue-green were the dominant colours, and polymer abundance decreased in the order polyethylene > nylon > polypropylene > polystyrene > polyethylene terephthalate. The distributions of sediment mass (range <0.01–9 g) and number of MPs (range = 0 to 21) were heterogeneous, both between sites and at the different heights sampled, and yielded median, vertically-averaged horizontal fluxes for the region of about 450 g m−2 d−1 and 2600 MP m−2 d−1, respectively. However, when data were pooled, the number of MPs normalised to sediment mass exhibited a significant inverse relationship with sediment mass, an effect attributed to the presence of ambient suspended MPs and sediment that are diluted by the suspension of soil and deposited MPs at higher wind speeds. The mechanisms of MP saltation and entrainment were not ascertained but a theoretical framework for threshold shear velocity based on regularly-shaped particles and density considerations is presented. Further experimental work is required to verify this framework, and in particular for fibrous MPs with different aerodynamic properties to soil particles.

Microplastics in Freshwater Sediments Impact the Role of a Main Bioturbator in Ecosystem Functioning.

While microplastic transport, fate, and effects have been a focus of studies globally, the consequences of their presence on ecosystem functioning have not received the same attention. With increasing evidence of the accumulation of microplastics at sediment-water interfaces there is a need to assess their impacts on ecosystem engineers, also known as bioturbators, which have direct and indirect effects on ecosystem health. This study investigated the impact of microplastics on the bioturbator Tubifex tubifex alongside any effects on the biogeochemical processes at the sediment-water interface. Bioturbators were exposed to four sediment microplastic concentrations: 0, 700, 7000, and 70000 particles kg-1 sediment dry weight. Though no mortality was present, a significant response to oxidative stress was detected in tubificid worms after exposure to medium microplastic concentration (7000 particles kg-1 sediment dry weight). This was accompanied by a reduction in worm bioturbation activities assessed by their ability to rework sediment and to stimulate exchange water fluxes at the sediment-water interface. Consequently, the contributions of tubificid worms on organic matter mineralization and nutrient fluxes were significantly reduced in the presence of microplastics. This study demonstrated that environmentally realistic microplastic concentrations had an impact on biogeochemical processes at the sediment-water interface by reducing the bioturbation activities of tubificid worms.

Substantial burial of terrestrial microplastics in the Three Gorges Reservoir, China

Hydropower dams impact the transport of microplastics from rivers to the ocean. The Yangtze River is a large source of plastics to the ocean. Here, we report microplastic concentrations and compositions across a range of size fractions for sediment samples collected in the upper and lower reaches of the Three Gorges Dam in 2008, 2015, 2019 and 2020. We find a gradual increase in microplastic abundance over time, with preferential retention of small-sized (<300 μm) microplastics in the dam reservoir sediments. Small microplastics accounted for between approximately 44 and 90% of identified microplastics, and 82% of all polyethylene particles, which were the dominant polymer type. Our estimate of the total plastic mass load in reservoir sediments suggests that the Three Gorges Dam retains as much as 8048 ± 7494 tons yr‒1 microplastics in sediments, which is equivalent to 47 ± 44% of the Yangtze River microplastic flux to the ocean.

Entrainment and Enrichment of Microplastics in Ice Formation Processes: Implications for the Transport of Microplastics in Cold Regions.

Sea ice can serve as a temporary sink for microplastics (MPs), and thus, it too can function as a secondary source of and transport medium for MPs. This study aimed to explore the effect of various MP properties and environmental characteristics on the entrainment and enrichment of MPs in ice under varying turbulence conditions. It was found that high rotation speed in freshwater distinctively enhanced the entrainment of hydrophobic MPs in ice, this being attributable to the combined effects of frazil ice and air bubbles. The hydrophobic nature of these MPs caused them to be attracted to the water/air or water/ice interface. However, in saline water, high turbulence inhibited the entrainment of all of the MP types under study. The ice crystals formed a loose structure in saline water instead of congealing, and this allowed the exchange of MPs between ice and water, leading to the rapid expulsion of MPs from the ice. The enrichment factors of all the MPs under study increased in calm saline water compared to in calm freshwater. The results revealed that the entrainment and enrichment of MPs in ice can be critical pathways affecting their fate in cold regions.

Modeling of vertical microplastic transport by rising bubbles

Microplastic particle concentration at the sea surface is critical for quantifying microplastic transport across the water-air interface. Previous studies suggest that the concentration at the sea surface is enhanced compared to bulk concentration, yet little is known about the detailed mechanisms behind this enhancement. In this work, we model one particular process in simulation that may contribute to this enhanced surface concentration: bubble scavenging. Using lattice-Boltzmann Volume-of-Fluid simulations, we find that rising bubbles indeed generate a net flow of particles toward the surface. The efficiency of the process, however, highly depends on the microplastic particle surface properties. Clean, hydrophobic particles adhere much better to the bubble surface and are therefore transported significantly better than weathered, hydrophilic particles that are only entrained in the flow around a bubble.

Environmental fate of microplastics in an urban river: Spatial distribution and seasonal variation

Rivers are recognized as an important pathway for transport of microplastics (MPs) from land to sea, but limited information is available on the spatial distribution and seasonal variation of riverine MPs from upper reaches to estuaries. Such information is critical for source apportionment and development of effective management measures for riverine MPs. To fill the knowledge gap, we investigated the occurrence of MPs in surface water along an urban river in Guangzhou, southern China in wet and dry seasons. The abundances of MPs from 16 sampling sites in the wet and dry seasons varied from 0.123 to 1.84 particles m-3 and from 0.046 to 4.21 particles m-3, respectively. The spatial distribution of MP abundances showed an increasing trend from upstream to midstream and a decreasing trend from midstream to downstream and estuaries. The abundances of MPs peaked at the midstream, which is surrounded by a highly urbanized region with high population density (∼2530 persons per km2). The large surface water runoff during the wet season elevated the MP abundance in riverine water, except for that flowing through the central urban area where the abundance of MPs collected in the dry season was higher than that in the wet season. This was mainly ascribed to the large input from extensive anthropogenic activities and slow water flow rate in urban areas. The estimated monthly riverine MP fluxes from Humen, Hongqili, and Jiaomen were 7.42, 2.38, and 2.3 billion particles, respectively, in the wet season, and 0.86, 0.71, and 0.19 billion particles, respectively, in the dry season. An increase of riverine MP fluxes from Humen, Hongqili, and Jiaomen in the past three years was evident. The results from the present study provide valuable information for source apportionment of riverine MPs and support the initialization of possible MPs controlling measures.

Cryosphere as a temporal sink and source of microplastics in the Arctic region

Microplastics (MPs) pollution has become a serious environmental issue of growing global concern due to the increasing plastic production and usage. Under climate warming, the cryosphere, defined as the part of Earth’s layer characterized by the low temperatures and the presence of frozen water, has been experiencing significant changes. The Arctic cryosphere (e.g., sea ice, snow cover, Greenland ice sheet, permafrost) can store and release pollutants into environments, making Arctic an important temporal sink and source of MPs. Here, we summarized the distributions of MPs in Arctic snow, sea ice, seawater, rivers, and sediments, to illustrate their potential sources, transport pathways, storage and release, and possible effects in this sentinel region. Items concentrations of MPs in snow and ice varied about 1–6 orders of magnitude in different regions, which were mostly attributed to the different sampling and measurement methods, and potential sources of MPs. MPs concentrations from Arctic seawater, river/lake water, and sediments also fluctuated largely, ranging from several items of per unit to >40,000 items m−3, 100 items m−3, and 10,000 items kg−1 dw, respectively. Arctic land snow cover can be a temporal storage of MPs, with MPs deposition flux of about (4.9–14.26) × 108 items km−2 yr−1. MPs transported by rivers to Arctic ocean was estimated to be approximately 8–48 ton/yr, with discharge flux of MPs at about (1.65–9.35) × 108 items/s. Average storage of MPs in sea ice was estimated to be about 6.1×1018 items, with annual release of about 5.1×1018 items. Atmospheric transport of MPs from long-distance terrestrial sources contributed significantly to MPs deposition in Arctic land snow cover, sea ice and oceanic surface waters. Arctic Great Rivers can flow MPs into the Arctic Ocean. Sea ice can temporally store, transport and then release MPs in the surrounded environment. Ocean currents from the Atlantic brought high concentrations of MPs into the Arctic. However, there existed large uncertainties of estimation on the storage and release of MPs in Arctic cryosphere owing to the hypothesis of average MPs concentrations. Meanwhile, representatives of MPs data across the large Arctic region should be mutually verified with in situ observations and modeling. Therefore, we suggested that systematic monitoring MPs in the Arctic cryosphere, potential threats on Arctic ecosystems, and the carbon cycle under increasing Arctic warming, are urgently needed to be studied in future.

Effects of organic matter on the aggregation of anthropogenic microplastic particles in turbulent environments

Biofilm-coated microplastics are omnipresent in aquatic environments, carrying different organic matter (OM) that in turn influences the flocculation and settling of microplastic aggregates. In this study, the effects of chitosan, guar gum, humic acid, and xanthan gum on the flocculation of anthropogenic microplastics are examined under controlled shear through the mixing chamber experiments. The results show that all of the selected OMs have positive effects on biofilm culturing and thus enhance the growth of microplastic flocs, with more evident promoting effects for cationic and neutral OMs (i.e., chitosan and guar gum) than anionic OMs (i.e., humic acid and xanthan). No critical shear rate is observed in the size vs. shear relationship based on our measurements. In addition, the quadrature-based two-class population balance model is employed to track the development of bimodal floc size distributions (FSDs) composed of small and large microplastic flocs. The model predictions show reasonable agreement with the observed FSDs. The largest error of settling flux from the two-class model is 7.8% in contrast with the reference value measured by the camera-based FSDs with 30 bins. This study highlights the role of different OMs on microplastic flocculation and indicates that a two-class model may be sufficient to describe microplastic transport processes in estuaries.