Raman Spectroscopy Research Articles

Lead-free Polymer Composite Film for Photon Energy Influenced Piezoelectric Nanogenerator based on Photoactive SnS2

Piezoelectric nanogenerators (PENGs) can power microelectronics, which convert weak mechanical vibrations to electrical impulses; however, low output voltage and poor mechanical durability limit PENG use. Thus, we provide photoactive SnS2 nanofillers in a PVDF matrix for piezoelectric nanogenerators (PPENGs). Raman spectroscopy demonstrates improvement of the electroactive β-phase of PVDF due to adding photoactive hexagonal SnS2 nanoparticles with a band gap of 2.4 eV. Sandwiching the PVDF-SnS2 composite between ITO-coated substrates with silver paste contacts fabricated the PPENG. The open-circuit voltage of PPENG is 24.4 V in the dark and 72.9 V under illumination with a short-circuit current of 0.75 μA, showing its outstanding photo responsiveness. The high light absorption of SnS2 and PVDF-SnS2 interfacial polarization caused the improved response. High-performance optoelectronic and energy harvesting applications may employ this photoactive piezoelectric nanogenerator development technique.

On the influence of structural and chemical properties on the elastic modulus of woven bone under healing

IntroductionWoven bone, a heterogeneous and temporary tissue in bone regeneration, is remodeled by osteoblastic and osteoclastic activity and shaped by mechanical stress to restore healthy tissue properties. Characterizing this tissue at different length scales is crucial for developing micromechanical models that optimize mechanical parameters, thereby controlling regeneration and preventing non-unions.MethodsThis study examines the temporal evolution of the mechanical properties of bone distraction callus using nanoindentation, ash analysis, micro-CT for trabecular microarchitecture, and Raman spectroscopy for mineral quality. It also establishes single- and two-parameter power laws based on experimental data to predict tissue-level and bulk mechanical properties.ResultsAt the macro-scale, the tissue exhibited a considerable increase in bone fraction, controlled by the widening of trabeculae. The Raman mineral-to-matrix ratios increased to cortical levels during regeneration, but the local elastic modulus remained lower. During healing, the tissue underwent changes in ash fraction and in the percentages of Calcium and Phosphorus. Six statistically significant power laws were identified based on the ash fraction, bone fraction, and chemical and Raman parameters.DiscussionThe microarchitecture of woven bone plays a more significant role than its chemical composition in determining the apparent elastic modulus of the tissue. Raman parameters were demonstrated to provide more significant power laws correlations with the micro-scale elastic modulus than mineral content from ash analysis.

Tailored Functional Monolayers Made from Mesoionic Carbenes

Significant progress has been made over the last decades in surface functionalization of coinage metals using thiols and more recently N-heterocyclic carbenes. As shown in this work, mesoionic carbenes (MICs) provide straightforward access to a novel class of surface ligands including electroactive ones and thus materials. Importantly, MICs are easily accessed from triazolium salts (TS) onto which functional groups may be attached with little synthetic effort. Here, we present a library of TS that were further converted, in situ, into MICs and grafted onto gold surfaces. The modified surfaces were thoroughly characterized by advanced spectroscopic methods such as XPS, infrared and Tip-Enhanced Raman Spectroscopy. Through cyclic voltammetry at 100 Vs-1, we could evaluate the surfacic concentration of the grafted molecules for electroactive MICs. We also prepared mixed MIC/thiol self-assembled monolayers, which opens the route to multifunctional surfaces.

ZIFs@MIL-101/urea-derived magnetic FeCo nitrogen-rich carbon as an effective and stable catalyst for peroxymonosulfate activation

High efficiency and stability are key issues in heterogeneous metal catalytic materials/peroxymonosulfate (PMS) systems during wastewater degradation. However, catalytic materials that are difficult to recover and metal leaching can cause secondary contamination of water bodies. Herein, we designed the magnetic FeCo nitrogen-rich carbon (FeCo-NC) obtained by layer-by-layer encapsulation, followed by urea encapsulation of in situ grown MOF-in-MOF and carbonization. The CoFe2O4 crystalline nature of FeCo-NC was confirmed by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), and selected angle electron diffraction (SAED) results, which is responsible for the magnetic properties of FeCo-NC. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) present that the material's morphology transforms from dodecahedral ZIF-67 to spindle-shaped ZIF-67@MIL-101 and then to octahedral FeCo-NC. Compared with FeCo-C and ZIF-67@MIL-101, the removal efficiency of FeCo-NC was maintained at 78.6% after 10 consecutive cycles, with only a 17% loss of raw material. The Fe and Co leaching amounts in the FeCo-NC/PMS system were approximately 0.6 and 0.1mg/L, respectively, much lower than China's Fe and Co emission standards. FeCo-NC characterization and TC degradation results demonstrated that magnetic CoFe2O4 nanoparticles formed on the surface or inside the FeCo-NC could effectively inhibit metal (Fe and Co) loss and be easily regenerated in multiple degradation cycles. The mechanism and degradation routes in the FeCo-NC/PMS/ TC system, including the radical/nonradical pathways, Fe/Co valence change, and electron transfer, were further investigated by electron paramagnetic resonance experiments, electrochemical analyses, in situ Raman spectroscopy, and HPLC–MS experiments.

Structure and electrical properties of polysilicon films doped with ammonium tetraborate tetrahydrate

Here, p-type polysilicon films are fabricated by ex-situ doping method with ammonium tetraborate tetrahydrate (ATT) as the boron source, named ATT-pPoly. The effects of ATT on the properties of polysilicon films are comprehensively analyzed. The Raman spectra reveal that the ATT-pPoly film is composed of grain boundary and crystalline regions. The preferred orientation is the (111) direction. The grain size increases from 16−23 nm to 21−47 nm, by ~70% on average. Comparing with other reported films, Hall measurements reveal that the ATT-pPoly film has a higher carrier concentration (>1020 cm−3) and higher carrier mobility (>30 cm2/(V·s)). The superior properties of the ATT-pPoly film are attributed to the heavy doping and improved grain size. Heavy doping property is proved by the mean sheet resistance (R sheet,m) and distribution profile. The R sheet,m decreases by more than 30%, and it can be further decreased by 90% if the annealing temperature or duration is increased. The boron concentration of ATT-pPoly film annealed at 950 °C for 45 min is ~3 × 1020 cm−3, and the distribution is nearly the same, except near the surface. Besides, the standard deviation coefficient (σ) of R sheet,m is less than 5.0%, which verifies the excellent uniformity of ATT-pPoly film.

The use of 1D carbon nanotube interacting with caffeine molecules for applications in solar cells: structure optimisation, Raman analysis and optoelectronic properties

This study proposes a promising candidate for organic solar cells through the creation of a novel nano-hybrid system composed of caffeine molecules encapsulated within a semiconducting single-walled carbon nanotube known as NT14 (14,0). The stability and optoelectronic properties of this hybrid system, designated as CA@NT14, were thoroughly investigated. We determined the optimal diameter for the NT14 nanotube using molecular mechanics, Density Functional Theory, spectral moment’s method, and bond polarizability model, finding it to be approximately 1.18 nm. The encapsulation’s impact on the Raman-active modes, specifically the radial breathing mode and tangential mode, was analyzed through Raman spectra calculations, revealing structural stability and charge transfer from CA to NT14. Notably, the NT14’s Fermi level position increased upon encapsulation, indicating charge transfer and a type-II band alignment. The study further examined the bandgap characteristics of the hybrid system, finding that the encapsulation of CA within semiconducting NT14 nanotubes minimally impacts the nanotube’s bandgap, thus retaining its excellent visible light absorption properties. Conversely, encapsulating CA within metallic nanotubes significantly reduces their bandgap, limiting their light absorption range. The nonresonant Raman responses of NT14 pre- and post-encapsulation corroborated the charge transfer between CA and NT14. Future research will focus on computing the electronic transport characteristics, transmission spectra, I-V characteristics, and yield of CA@NT14 using DFT and Non-Equilibrium Green’s Function ( formalism. An experimental study will be conducted to validate these theoretical findings. These results indicate the potential of CA@NT14 hybrids as effective active layers in organic solar cells, highlighting their significance in advancing optoelectronic applications.

Enhanced electrochemical performance of garnet Li7La3Zr2O12 electrolyte by efficient incorporation of LiCl

Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) lithium-ion-conducting ceramic electrolytes has become the promising and critical candidate for developing the high-energy-density all-solid-state lithium batteries, due to the satisfied Li+ conductivity, stability against metallic lithium anode, and the feasible preparation under ambient air. Here, to further increase the lithium-ion conductivity of LLZO comparable to that of the commercial organic liquid electrolytes, lithium chloride (LiCl) is effectively introduced to synthesize the garnet-type ceramic electrolytes with the nominal composition (Li6.5La3Zr1.5Ta0.5O12)1-x–(LiCl)x (x=0, 5mol%, 10mol%, 15mol%, 20mol%, and 25mol%) via high-temperature calcination process. The cubic structure with highly conductive performance is confirmed from X-ray diffraction measurement as well as Raman spectra analysis. Structural information is observed according to field emission scanning electron microscope equipped with energy dispersive spectrometer and density measurements. Among above investigated ceramic compositions, the prepared (Li6.5La3Zr1.5Ta0.5O12)0.85–(LiCl)0.15 ceramic electrolyte sheet sintered at 1200°C for 12h presents the room-temperature Li-ion conductivity of 1.22×10-3S·cm-1 by alternating current (AC) impedance analysis along with the corresponding activation energy of 0.262eV through Arrhenius equation calculation. The electronic conductivity measurements are also done by direct-current polarization to confirm the ionic nature for all investigated ceramics. Furthermore, the Li|(Li6.5La3Zr1.5Ta0.5O12)0.85–(LiCl)0.15 |Li symmetric batteries can possess the small interfacial resistance of 92.3 Ω·cm2 and stably run for 1000 h at 0.1 mA·cm−2 without a short circuit at room temperature. The hybridized lithium-sulfur battery with (Li6.5La3Zr1.5Ta0.5O12)0.85–(LiCl)0.15 electrolyte delivered excellent initial room-temperature discharge capacity of 1204mAh·g-1 and 1150mAh·g-1 under the current density of 0.1C and 0.2C respectively, large coulombic efficiency, and great cycling stability. Moreover, the lithium-sulfur batteries also can show excellent cycling performances under different current densities and a good capacity recoverability. The above investigation results suggest that the low-melting-point LiCl incorporation in Li6.5La3Zr1.5Ta0.5O12 electrolyte is an effective measurement to synthesize the cubic and dense Li-stuff garnet ceramic sheets for the high-performance rechargeable next-generation solid-state batteries.

Raman study of apatite coating, obtained by gas-detonation deposition detonation spraying of the precursor salts on the titanium substrates

The results of the Raman study of the apatite coatings, obtained by gas-detonation deposition detonation spraying of the precursor salts on the titanium substrates are presented. The mixture of Ca(OH)2 and (NH4)2HPO4 salts at the molar ratio 5:3 was used as precursors. A detailed analysis of the most intense Raman band showed hydroxyapatite formation with a dominant contribution of the amorphous phase. The post-deposition thermal annealing at 640 °C for 30 min in the Ar atmosphere leads to the transformation of the amorphous hydroxylapatite into the crystalline one.

Multimodal Non-Destructive In Situ Observation of Crystallinity Changes in High-Density Polyethylene Samples with Relation to Optical Parameters during Tensile Deformation

Abstract: Many non-destructive optical testing methods are currently used for material research, providing various information about material parameters. At RECENDT, a multimodal experimental setup has been designed that combines terahertz (THz) spectroscopy, optical coherence tomography (OCT), infrared (IR), and Raman spectroscopy with a tensile test stage. This setup aims to gather material information such as crystallinity and optical parameters of high-density polyethylene (HDPE) during a tensile test. The setup compares common IR and Raman spectroscopy and the less common optical methods THz and OCT. Complementarity is achieved through different frequency ranges and measurement approaches, resulting in different measured optical material parameters and depths. During tensile testing, HDPE samples with varying crystallinity were analysed, and the determined optical parameters such as refractive index, birefringence, scattering coefficient of decay, and penetration depth can be correlated with the change in crystallinity. These findings demonstrate that the optical methods and their outcomes can be interconnected. With further optimization of the experimental setup, it would be possible to observe the alignment of fibres in fibre composite panels and the stress distribution of polymers effectively. This opens interesting possibilities for polymer characterization in the future, including quality control during moulding processes and material testing.

Photoluminescent carbon colloids prepared by laser fragmentation of carbon from waste coffee grounds

Colloidal suspensions of carbon nanostructures (CNSs) were prepared by laser fragmentation in various liquid media using heat-treated coffee grounds as carbon precursor. A study by calorimetry was done in powder of waste coffee grounds to determine the temperature of obtaining carbon. The experiments were carried out in two stages, the first one consisted in obtaining the carbon source, for which powder of waste coffee grounds was thermally treated in air. The as-obtained carbon was characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, Raman spectroscopy and infrared spectroscopy. In the second step the as-obtained carbon was separately dispersed in four liquid media (acetone, toluene, methanol and isopropyl alcohol) to be fragmented by using a ns-pulsed Nd:YAG laser at its 1064 nm fundamental emission. The morphological features of the carbon nanostructures were obtained by transmission electron microscopy, while the optical properties of the colloidal suspensions were characterized by UV-Vis and photoluminescence spectroscopies. Results indicate that carbon nanostructures are successfully obtained in the four liquid media after the fragmentation process. The four colloidal suspensions show photoluminescent properties, which are seen to depend on the liquid medium nature. We found that the liquid medium also influences the efficiency of the laser fragmentation.

Zygospore formation in Zygnematophyceae predates several land plant traits.

Recent research on a special type of sexual reproduction and zygospore formation in Zygnematophyceae, the sister group of land plants, is summarized. Within this group, gamete fusion occurs by conjugation. Zygospore development in Mougeotia, Spirogyra and Zygnema is highlighted, which has recently been studied using Raman spectroscopy, allowing chemical imaging and detection of changes in starch and lipid accumulation. Three-dimensional reconstructions after serial block-face scanning electron microscopy (SBF-SEM) or focused ion beam SEM (FIB-SEM) made it possible to visualize and quantify cell wall and organelle changes during zygospore development. The zygospore walls undergo strong modifications starting from uniform thin cell walls to a multilayered structure. The mature cell wall is composed of a cellulosic endospore and exospore and a central mesospore built up by aromatic compounds. In Spirogyra, the exospore and endospore consist of thick layers of helicoidally arranged cellulose fibrils, which are otherwise only known from stone cells of land plants. While starch is degraded during maturation, providing building blocks for cell wall formation, lipid droplets accumulate and fill large parts of the ripe zygospores, similar to spores and seeds of land plants. Overall, data show similarities between streptophyte algae and embryophytes, suggesting that the genetic toolkit for many land plant traits already existed in their shared algal ancestor. This article is part of the theme issue 'The evolution of plant metabolism'.

Microbiome-induced Increases and Decreases in Bone Matrix Strength can be Initiated After Skeletal Maturity.

Recent studies in mice have indicated that the gut microbiome can regulate bone tissue strength. However, prior work involved modifications to the gut microbiome in growing animals and it is unclear if the same changes in the microbiome, applied later in life, would change matrix strength. Here we changed the composition of the gut microbiome before and/or after skeletal maturity (16weeks of age) using oral antibiotics (ampicillin + neomycin). Male and female mice (n= 143 total, n= 12-17/group/sex) were allocated into five study groups:1) Unaltered, 2) Continuous (dosing 4-24weeks of age), 3) Delayed (dosing only 16-24weeks of age), 4) Initial (dosing 4-16weeks of age, suspended at 16weeks), and 5) Reconstituted (dosing from 4-16weeks following by fecal microbiota transplant from Unaltered donors). Animals were euthanized at 24weeks of age. In males, bone matrix strength in the femur was 25-35% less than expected by geometry in mice from the Continuous (P=.001), Delayed (P=.005), and Initial (P=.040) groups as compared to Unaltered. Reconstitution of the gut microbiota led to a bone matrix strength similar to Unaltered animals (P=.929). In females, microbiome-induced changes in bone matrix strength followed the same trend as males but were not significantly different, demonstrating a sex-dependent response of bone matrix to the gut microbiota. Minor differences in chemical composition of bone matrix were observed with Raman spectroscopy. Our findings indicate that microbiome-induced impairment of bone matrix in males can be initiated and/or reversed after skeletal maturity. The portion of the femoral cortical bone formed after skeletal maturity (16weeks) was small; suggesting that microbiome-induced changes in bone matrix occurred without osteoblast/osteoclast turnover through a yet unidentified mechanism. These findings provide evidence that the mechanical properties of bone matrix can be altered in the adult skeleton.

Dislocation evolution in anisotropic deformation of GaN under nanoindentation

The exceptional performance of GaN semiconductors in lasers, wireless communication, and energy storage systems makes them crucial for future multi-functional devices. However, during the polishing of GaN wafers, abrasive particles can induce subsurface damage, compromising device performance. This study investigates dislocation loops in GaN single crystal to understand dislocation nucleation and glide under external stress. Using nanoindentation for compressive stress, we confirmed multiple slip system activation via transmission electron microscopy after pop-in. We also performed molecular dynamics to simulate the nucleation and multiplication of U-shaped dislocation loops. Furthermore, we developed a theoretical model using Peierls–Nabarro stress to quantify GaN's critical shear stress. Raman spectroscopy was also used to analyze shear stress on U-shaped loops, supporting our model. This study provides insights into GaN dislocation dynamics under mechanical stress, aiding in wafer defect evaluation during machining and offering guidance for dislocation evolution.

Exploring Polymorphism in Quinoline‐4‐Carbaldoxime: Experimental Validation and Computational Insights into Hydrogen Bonding and Structural Variations

AbstractThis study identifies and characterizes a second polymorph (Poly‐II) of quinoline‐4‐carbaldoxime (HQ), isolated from an acetone‐acetonitrile mixture. Poly‐II was compared to the previously known Poly‐I using PXRD, DSC, IR, and Raman spectroscopy. Poly‐I forms a 1D supramolecular assembly, whereas Poly‐II exhibits a 2D assembly with additional hydrogen bonds. Hirshfeld surface analysis reveals the presence of different non‐covalent interactions in Poly‐I and Poly‐II, and atom‐in‐molecule (AIM) analysis identifies their strength. AIM analysis, along with Espinosa's relation, was used to calculate the strength of O─H···N and C─H···N interactions in Poly‐I and Poly‐II. The values are −30.0 and −6.17 kJ/mol for Poly‐I, whereas the values for Poly‐II are −36.18 and −3.66 kJ/mol. The plane wave periodic DFT calculations determined the lattice energies of Poly‐I and Poly‐II to be −1.52 and −1.53 eV, respectively, indicating that both polymorphs have comparable stability. The crystal parameters of Poly‐I and Poly‐II obtained from theoretical simulations and the experiment are comparable, indicating the similar stability of Poly‐I and Poly‐II. Computational simulations confirmed experimental data, showing both polymorphs have similar stability and melting points despite different unit cell volumes.

Biosynthesis of iron-chelating terramides A-C and their role in Aspergillus terreus infection

Fungal natural products from various species often feature hydroxamic acid motifs that have the ability to chelate iron. These compounds have an array of medicinally and ecologically relevant activities. Through genome mining, gene deletion in the host Aspergillus terreus, and heterologous expression experiments, this study has revealed that a nonribosomal peptide synthetase (NRPS) TamA and a specialized cytochrome P450 monooxygenase TamB catalyze the sequential biosynthetic reactions in the formation of terramides A-C, a series of diketopiperazines (DKPs) with hydroxamic acid motifs. Feeding experiments showed that TamB catalyzes an unprecedented di-hydroxylation of the amide nitrogens in the diketopiperazine core. This tailoring reaction led to the formation of two bidentate iron-binding sites per molecule with an unusual iron-binding stoichiometry. The structure of the terramide A-Fe complex was characterized by liquid chromatography-mass spectrometry (LC-MS), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy and electron paramagnetic resonance spectroscopy (EPR). Antimicrobial assays showed that the iron-binding motifs are crucial for the activity against bacteria and fungi. Murine infection experiments indicated that terramide production is crucial for the virulence of A. terreus and could be a potential antifungal drug target.

Highly sensitive electrochemical sensor based on flexible porous graphene for cortisol detection

This report presents the development of an electrochemical sensor for detecting cortisol in sweat, utilizing a flexible porous graphene electrode (fPGE). The fPGE was created using the laser-induced graphene technique on a polyimide substrate. The characterization of the porous graphene material was conducted through SEM and Raman spectroscopy. The graphene surface of the fPGE was modified with cortisol-aptamer with the assistance of linker molecules, PASE, to form the cortisol sensor. The electrochemical properties of the sensor were assessed using cyclic voltammetry technique (CV). Cortisol detection in the sensor was achieved indirectly via the reaction of the redox couple K4[Fe(CN)6]/K3[Fe(CN)6] on the surface of the cortisol aptamer-modified fPGE. As the concentration of cortisol in the solution increased, the corresponding current in the CV decreased. Under optimized conditions, the electrochemical cortisol sensor demonstrated a wide dynamic range of cortisol concentration from femtomolar (fM) to micromolar (µM) with a low limit of detection (LOD) of 100 fM.

Spectroscopic Investigation of Pearl Samples from Online Platforms and E-Marketplaces

P urchasing pearls from online platforms and e-marketplaces has been around for years, where buyers could join in the thrill of the show of opening pearls from oysters or mollusks. In exchange for those materials that claim to be pearls, buyers must pay a high price per piece. In this study, the spectroscopic properties of twenty-seven samples purchased from online platforms and e-marketplaces were revealed. The FTIR spectra show the characteristic peaks of aragonite at 1483, 716, 712, and 699 cm-1, while exhibiting the vaterite peaks at 882 and 879 cm-1. Correspondingly, Raman spectra indicate the ν1 symmetrical and ν4 in-plane bending modes of the carbonate at 1083, 701, and 704 cm-1. Thus, it clarified that all the samples are pearls. The SrO/MnO ratio acquired by energy dispersive X-ray spectroscopy (EDXRF) at an average of 0.44 suggested that the samples are freshwater pearls. Apart from the white pearl, the cause of the color of the sample is separated into two factors. The natural color, which is presented in cream and peach, is caused by polyene pigments. In contrast, vivid colors such as blue, violet, purple, and pink are shown as evidence of dyes. The UV-Vis reflectance spectra also present a different absorption between natural and dyed pearls.

Vibrational Fermi Resonance in Atomically Thin Black Phosphorus.

Fermi resonance is a phenomenon involving the hybridization of two coincidentally quasi-degenerate states that is observed in the vibrational or electronic spectra of molecules. Despite numerous examples in molecular systems, vibrational Fermi resonances in dispersive semiconducting systems remain largely unexplored due to the rarity of occurrence. Here we report a vibrational Fermi resonance in atomically thin black phosphorus. The Fermi resonance arises via anharmonic mixing of a fundamental Raman mode and a Davydov component of an infrared mode, leading to a doublet with mixed character. The extent of Fermi coupling can be modulated by the application of external biaxial strain. The consequences of Fermi hybridization are revealed by electronic resonance effects in the thickness-dependent and excitation-wavelength-dependent Raman spectrum, which is predicted by ab initio hybrid functional simulations including excitonic interactions. This work reveals new insight into electron-phonon coupling in black phosphorus and demonstrates a novel method for modulating Fermi resonances in 2D semiconductors.

Tuning ferroelectric domains and polarization properties of flexible BiFeO3 thin films by phase transition engineering

In the present investigation, thin films of flexible (Bi1-xSmx)(Fe0.95Mn0.05)O3 (denoted as BSFM0, BSFM4, BSFM8, and BSFM12 for x=0 %, 4 %, 8 %, and 12 %, respectively) were synthesized on metallic Ni-Cr substrates via the sol-gel technique. A comprehensive examination was conducted to elucidate the influence of varying concentrations of Sm3+ substitution on the phase constitution, oxygen vacancy concentration, and leakage behavior of the (Bi1-xSmx)(Fe0.95Mn0.05)O3 films. Utilizing X-ray diffraction (XRD) and Raman spectrometry, it was ascertained that all films exhibited a composite structure comprising orthorhombic (Pnma) and rhombohedral (R3c) phases. An augmentation in Sm3+ doping led to a non-monotonic variation in the R3c phase content, initially increasing and subsequently decreasing, while the nonpolar Pnma phase demonstrated a progressive enhancement. The distorted R3c phase was found to promote the flipping of the domain architecture, thereby augmenting the polarization attributes. Notably, at a Sm doping level of 4 %, the maximum polarization (Pmax) attained was 95 μC/cm2, with a remnant polarization (Pr) of 78 μC/cm2. The incorporation of a judicious amount of Sm was observed to curtail film leakage and decelerate the aging phenomenon. The compositional stability of this doping level was evaluated across a frequency spectrum of 0.1–12 kHz and a temperature gradient of 25–200 °C, revealing no propensity for degradation under conditions of polarization, a holding duration of 104 s, or fatigue scenarios involving a curvature of 5 mm and 108 switching cycles subjected to 103 instances of bending. These findings provide innovative insights for the development of next-generation lead-free transducer apparatus and flexible information storage mediums.

Potential cycling boosts the electrochemical conversion of polyethylene terephthalate-derived alcohol into valuable chemicals

The electrocatalytic valorization of polyethylene terephthalate-derived ethylene glycol to valuable glycolic acid offers considerable economic and environmental benefits. However, conventional methods face scalability issues due to rapid activity decay of noble metal electrocatalysts. We demonstrate that a dynamic potential cycling approach, which alternates the electrode potential between oxidizing and reducing values, significantly mitigates surface deactivation of noble metals during electrochemical oxidation of ethylene glycol. This method enhances catalyst activity by 20 times compared to a constant-potential approach, maintaining this performance for up to 60 h with minimal deactivation. In situ Raman and X-ray absorption spectroscopy show that this effectiveness results from efficient removal of surface oxide during the reaction. The strategy is applicable to polyethylene terephthalate hydrolysates and various noble metals, such as palladium, gold, and platinum, with palladium showing a high conversion rate in recent studies. Our approach offers an efficient and durable method for electrochemical upcycling of biomass-derived compounds.