Metastable Oxygen Research Articles

Measurement of controlled metastable oxygen atom concentration from nitric oxide AC glow discharge plasma

Measurement of controlled metastable oxygen atom concentration from nitric oxide AC glow discharge plasma

Contribution of Metastable Oxygen Spectra to Fluctuated Waveform Tails after Breakdown Time in Air under Positive and Negative Impulse Voltages

In this study, we explored the correlation between fluctuated waveform tails under both positive and negative impulse voltages and their corresponding spectral lines during millisecond observations of arc discharge. We examined impulse voltages in ±100, ±125, and ±150 kV across 3, 3.5, and 4 cm gaps using spectroscopic analysis focused on oxygen excitations. Six selected spectra in ±100, ±125, and ±150 kV at 3.5 cm and two negative spectra of −100 kV at 3 and 4 cm were analyzed by identifying spectral lines in the wavelength range of 200–900 nm. The results revealed a correlation between the fluctuated waveform tails and spectral lines in positive voltage discharges, which were almost similar, while in negative voltage discharges, this correlation was found only in −100 kV at 3 and 4 cm. We concluded that during the spark phase for both positive and negative voltage discharges, symmetrical fluctuation in the waveform tails was observed after breakdown time, especially above the voltage level of the recombination phase. This suggested the presence of energetic oxygen excited states in the 200–400 nm range, with higher peak intensity than the O I line at 777.417 nm, observed in most positive impulse voltage discharges and at −100 kV with 3 and 4 cm gaps, contributing to rapid breakdown.

Spatially resolved TALIF investigation of atomic oxygen in the effluent of a CO2 microwave discharge

A diagnostic setup for one-dimensionally spatially resolved two-photon absorption laser-induced fluorescence (TALIF) detection of ground state oxygen atoms ( 2p43P2,1,0 ) is developed. The goal of this study is to investigate the evolution of temperatures and absolute number densities of oxygen atoms along the effluent of a low-pressure CO2 microwave discharge in order to gain insights into some of the mechanisms governing the post-discharge regime. The plasma source is operated at conditions of 600 W– 1200 W of absorbed power with flow rates of 74 sccm and 370 sccm pure CO2 at pressures between 1.2 mbar and 5 mbar with specific energy inputs up to 111.9 eV/molecule. These operating conditions exhibit high CO2 conversions (up to 90%) at low energy efficiencies (2%–7.4%), due to direct electron impact dissociation driving the conversion process resulting in splitting of CO2 into CO and metastable oxygen atoms. The TALIF measurements yield spatially resolved translational temperatures between 1000 K– 1600 K for most operating conditions and axial positions along the effluent. Reference measurements with xenon 6p′[3/2]2 are used for absolute number density calibration. The resulting axially resolved number density profiles of ground state atomic oxygen increase along the effluent, even at considerable distances of several centimeters from the active discharge, before they reach a maximum between 5×1020 m−3 and 2.2×1021 m−3 depending on the condition, and decrease after that. This behavior indicates the potential significance of quenching of metastable oxygen atoms within the post-discharge regime of the investigated CO2 discharges. The measured spatially resolved number density evolutions are qualitatively consistent with quenching via wall collisions being the dominant deactivation mechanism, underlining the importance of particle-wall interactions.

Metastable nickel–oxygen species modulate rate oscillations during dry reforming of methane

AbstractWhen a heterogeneous catalyst is active, it forms metastable structures that constantly transform into each other. These structures contribute differently to the catalytic function. Here we show the role of different metastable oxygen species on a Ni catalyst during dry reforming of methane by combining environmental scanning electron microscopy, near ambient pressure X-ray photoelectron spectroscopy, on-line product detection and computer vision. We highlight the critical role of dissociative CO2 adsorption in regulating the oxygen content of the catalyst and in CH4 activation. We also discover rate oscillations during dry reforming of methane resulting from the sequential transformation of metastable oxygen species that exhibit different catalytic properties: atomic surface oxygen, subsurface oxygen and bulk NiOx. The imaging approach allowed the localization of fluctuating surface regions that correlated directly with catalytic activity. The study highlights the importance of metastability and operando analytics in catalysis science and provides impetus towards the design of catalytic systems.

Detection of molecular oxygen using nanosecond-laser-induced plasma.

Molecular oxygen (O2) concentration is measured by employing nanosecond laser-induced plasmas (ns-LIP) over a broad temperature spectrum ranging from 300 K to 1000 K, in the presence of an additional oxygen-containing molecule, CO2. Typically, emission spectra emanating from ns-LIP are devoid of molecular information, as the ns-LIP causes the dissociation of molecular species within the plasma. However, atomic oxygen absorption lines that momentarily appear at 777 nm in the broadband emission from the early-stage plasma are determined to be highly sensitive to the O2 mole fraction but negligibly affected by the CO2 mole fraction. The atomic O absorbing the plasma emission originates from the O2 adjacent to the plasma: robust UV radiation from the early-stage plasma selectively dissociates adjacent O2, exhibiting a relatively low photodissociation threshold, thus generating the specific meta-stable oxygen capable of absorbing photons at 777 nm. A theoretical model is introduced, explicating the formation of the meta-stable O atom from adjacent O2. To sustain the UV radiation from the plasma under high-temperature and low-density ambient conditions, a preceding breakdown is triggered by a split laser pulse (532 nm). This breakdown acts as a precursor, seeding electrons to intensify the inverse-Bremsstrahlung photon absorption of the subsequent laser pulse (1064 nm). Techniques such as proper orthogonal decomposition (POD) and support vector regression (SVR) are employed to precisely evaluate the O2 mole fraction (<1% uncertainty), by analyzing the short-lived (<10 ns) O2-indicator depicted in the early-stage plasma.

Local enhancement of electron heating and neutral species generation in radio-frequency micro-atmospheric pressure plasma jets: the effects of structured electrode topologies

The effects of structured electrode topologies on He/O2 radio frequency micro-atmospheric pressure plasma jets driven at 13.56 MHz are investigated by a combination of 2D fluid simulations and experiments. Good qualitative agreement is found between the computational and experimental results for the 2D spatio-temporally resolved dynamics of energetic electrons measured by phase resolved optical emission spectroscopy, 2D spatially resolved helium metastable densities measured by tunable diode laser absorption spectroscopy and 2D spatially resolved atomic oxygen densities measured by two photon absorption laser induced fluorescence. The presence of rectangular trenches of specific dimensions inside the electrodes is found to cause a local increase of the electron power absorption inside and above/below these surface structures. This method of controlling the electron energy distribution function via tailored surface topologies leads to a local increase of the metastable and atomic oxygen densities. A linear combination of trenches along the direction of the gas flow is found to result in an increase of the atomic oxygen density in the effluent, depending linearly on the number of trenches. These findings are explained by an enhanced Ohmic electric field inside each trench, originating from (a) the low electron density, and, consequently, the low plasma conductivity inside the trenches, and (b) the presence of a current focusing effect as a result of the electrode topology.

Toward a theory of ‘stepped-leaders’ in lightning

An unresolved issue in the physics of lightning is an explanation for lightning proceeding to the ground by successive luminous steps separated by ‘dark’ times of many microseconds. There is also no explanation of the structure of the dark column connecting the streamer step with the cloud that can be km in length, is electrically conducting, yet has a very low sustaining electric field. It is proposed that these two processes can be explained by the accumulation of singlet delta metastable oxygen molecules excited in the corona pulses of lightning. The step time is necessary for the excitation of large metastable densities to produce significant metastable detachment of electrons from negative ions. The detached electrons form a highly conducting step, initially luminous, that causes a redistribution of electric fields and an increase in the potential and electric fields at the end of the step to make possible a further step by ionization. These features are supported by calculations of densities of electrons, positive ions, negative ions and singlet delta metastable oxygen molecules for the first 7 μs of a discharge chosen to be initiated by a 50 cm sphere of charged hail particles. The calculated corona streamers produce metastable densities of 1017 cm−3 near the corona source. These metastables, by electron detachment, produce a conducting cylinder 10 m long with a radius of 1 cm and an electron density ∼1012 cm−3 that is attributed to being the first step and a lightning ‘leader’. These conducting regions develop within them very low electric fields. Successive steps are likely to combine to form the long conductive columns of lightning that exist before the return stroke. Electron densities in the leader and the column are an equilibrium between electron production by metastable detachment and electron loss by attachment to neutral oxygen molecules, requiring no electric field.

Characterization of an atmospheric pressure plasma jet producing the auroral transition O(1S) to O(1D)

We present a detailed characterization of an atmospheric pressure plasma jet that produces the metastable oxygen states O(1S) and OD) with emission of the ‘auroral’ green line. The device used 99.999 pure argon as a working gas for the plasma generation. Optical emission spectroscopy was used to understand the active species present in the plasma jet and to infer the mechanism of O(1S) creation and destruction. The continuum spectrum was used in conjunction with a method based on machine learning for determining the arbitrary electron probability distribution function. Discharge and plasma properties were estimated from Lissajous plots and using calculations with the BOLSIG+ software. The metastable oxygen forms for all operating parameters of the plasma jet system in a linear electrode configuration. The camera images provided information of the overall plasma jet behavior as parameters were altered. While the metastable oxygen was produced for every iteration, the plasma jet behavior changed considerably when the powered and grounded electrodes are switched. Small admixtures of oxygen and nitrogen were introduced in the plasma jet to understand the kinetic processes of metastable oxygen destruction and the 557.7 nm auroral line. This behavior has implications for plasma reactive chemistry in fundamental areas such as auroral physics as well as technological applications of plasmas.

State enhanced actinometry in the COST microplasma jet

A new actinometry approach, helium state enhanced actinometry (SEA), is presented. This diagnostic uses the emission of the atomic states O(3p3P) (λ = 844.6 nm), Ar(2p1) (λ = 750.4 nm) and He(33S) (λ = 706.5 nm) and allows the atomic oxygen density and the mean electron energy to be determined simultaneously from the spectral line intensity ratios. Here, the atomic states are selected in a way that they cover a wide range of the electron energy distribution function (EEDF). The method is compared to the classical actinometry approach and energy resolved actinometry (ERA) based on measurements on the COST microplasma jet. In addition, a benchmark against two-photon absorption laser induced fluorescence measurements is performed. Both atomic oxygen densities and mean electron energies are in good agreement with the literature. Furthermore, SEA offers a number of advantages over known approaches. Firstly, the experimental complexity is significantly reduced by using time-integrated spectra instead of phase-resolved measurements, as used in the original ERA approach. Secondly, the precision of the electron energy measurement can be significantly improved by the use of the helium state. In addition, known uncertainties e.g. due to excitation of oxygen excited levels via metastable oxygen states can be reduced.

Optimal Discharge Parameters for Biomedical Surface Sterilization in Radiofrequency AR/O2 Plasma

Plasma parameters of radiofrequency discharge generated at low pressures in an argon-oxygen mixture addressed for biomedical surface sterilization have been optimized. Numerical results illustrate the density distributions of different species and electron temperatures during the electrical discharge process. The current discharge acting in the abnormal range decreases at higher oxygen gas flow rates. The temperature of electrons drops with pressure while it rises by adding oxygen. Nevertheless, electron density displays an adverse trend, exhibited by the electron’s temperature. The average particle density of the reactive species is enhanced in Ar/O2 compared to He/O2, which ensures a better efficiency of Ar/O2 in sterilizing bacteria than He/O2. The impact of oxygen addition on the discharge mixture reveals raised oxygen atom density and a reduction in metastable oxygen atoms. A pronounced production of oxygen atoms is achieved at higher frequency domains. This makes our findings promising for biomedical surface sterilization and leads to optimal parameter discharges used for sterilization being at 30% of oxygen gas ratio and 0.3 Torr pressure.

Modelling the insertion of O(1D) into methane on the surface of interstellar ice mantles

ABSTRACT The detection of many complex organic molecules (COMs) in interstellar space has sparked the study of their origins. While the formation of COMs detected in hot cores is attributed to photochemistry on warming grain surfaces followed by recombination of radicals and desorption, the formation routes in colder regions are still a debated issue with a number of theories such as cosmic ray bombardment on interstellar ice mantles or non-diffusive surface chemistry. Here, we present another method with reactions involving metastable atomic oxygen in the O(1D) state, which is initially produced by photodissociation of oxygen-containing species in interstellar ices. As a first example, we study the reactions of metastable oxygen atoms and methane in ices to form both formaldehyde and methanol. The reaction is studied incorporating two different surface processes: diffusive and non-diffusive chemistry. The formation of methanol and formaldehyde via metastable oxygen atoms is compared with well-known formation routes of both to understand the O(1D) contributions at different temperatures.

Toward a theory of ball lightning occurring in houses and aircraft

Gas discharge properties have been calculated, considering electrons, negative ions, positive ions and the metastable singlet delta oxygen molecules, to assess the possibility of ball lightning resulting from an electrical discharge. It is found that if the metastable molecules have very large densities of the order of 1017 cm−3, a stable ball-like plasma of electrons, positive ions, negative ions and metastable molecules is obtained, with electron densities of ~1011 cm−3. The ball can exist independent of the electrodes. There is an equilibrium within the ball between the detachment of electrons from negative ions by the metastables and the re-attachment of electrons to oxygen atoms reforming negative ions. As the ball is highly conducting, electric fields within the ball are very low. Such a high density of metastable molecules could be accumulated from corona pulses from a high voltage point within any structure such as a house or aircraft fuselage. Large electric fields would be present at the tips of such metal conductors within an ambient electric field existing during a thunderstorm. It is also calculated that significant electric fields exist at the edges of the plasma ball to match the ball potential with the ambient potential and that these fields can be sufficient to excite further metastable molecules and increase the ball lifetime.

Enhanced dielectric properties with a significantly reduced loss tangent in (Mg2+, Al3+) co-doped CaCu3Ti4O12 ceramics: DFT and experimental investigations.

CaCu3Ti4O12 and CaCu2.95Mg0.05Ti3.95Al0.05O12 ceramics were fabricated via a solid-state reaction method. A single-phase of CaCu3Ti4O12 was found in these two ceramics. Very great grain size expansion was produced by co-doping with Mg2+ and Al3+. DFT results indicate that both Mg and Al atoms preferentially occupy Cu sites, creating liquid-phase sintering decomposition at grain boundary layers. Very high dielectric permittivity of ∼58 397 and low loss tangent of about 0.047 were achieved in a CaCu2.95Mg0.05Ti3.95Al0.05O12 ceramic. Additionally, the temperature stability of the dielectric response was improved. Better dielectric properties in the co-doped ceramic have possible origins from enhanced grain boundary responses, especially from the influences of metastable phases and oxygen enrichment at the grain boundaries. Experimental and computational results indicate that the colossal dielectric properties in CaCu3Ti4O12 ceramics might be correlated with an internal barrier layer capacitor structure.

Чисельне моделювання нестаціонарних потоків холодної плазми при роботі плазмового актуатора

The numerical simulation of unsteady flows of cold plasma is considered in this article. A low-temperature non-equilibrium ideal plasma is formed when the plasma actuator interacts with the air. The mathematical model has been developed to describe the behavior of low-temperature plasma. It is based on non-stationary equations describing the dynamics of charged particles and plasma electrodynamics equations. The 14 types of particles: metastable and excited nitrogen and oxygen atoms, positive and negative ions, electrons and atomic oxygen are considered. Volumetric and surface chemical reactions describing processes in a barrier discharge that occur above the dielectric surface are considered. For non-stationary equations of plasma dynamics, an implicit numerical algorithm with pseudo-time iteration has been developed, which is based on a finite-volume approach. The equation for the electrostatic potential with sources was solved using the generalized minimal residual method with incomplete LU preconditioning. In non-stationary equations for the density of plasma particles, the drift derivatives were approximated using the TVD scheme with the MinMod limiter function. The derivatives in the equation for the electric potential were calculated using finite-volume relations taking into account the upwind approximation of the concentration of charged plasma particles. The numerical results of the generation, propagation and destruction of a streamer during a dielectric barrier discharge are obtained. The unsteady plasma characteristics in the region above the dielectric surface are analyzed, including the distribution of the particles density, electric potential and the Lorentz force components. The results of numerical simulation of unsteady flows of low-temperature plasma are in good agreement with the available experimental data.

Enhanced interfacial reaction of precursor and low temperature substrate in HfO2 atomic layer deposition with highly Ar diluted O2 plasma

The internal energy of metastable oxygen atoms in highly Ar diluted oxygen plasma was utilized in the initial stage of the atomic layer deposition of HfO2 on SiO2/Si(100) at low temperature of 150 °C. The highly Ar dilute oxygen plasma enhanced the oxidation of the incomplete chemisorption state of the precursor at low temperature, successfully formed Hf silicate interface, and decreased the impurity nitrogen atoms in the HfO2 film compared to the pure oxygen plasma ALD. Residual nitrogen atoms in the film were found to cause excessive precursor adsorption. The results of plasma emission spectroscopy and ion saturation current measurements show that the highly Ar-diluted O2 plasma can increase the O radical formation rate for ion fluxes at pressures above 100 Pa. The relatively high metastable oxygen atom irradiation is thought to be responsible for the removal of HfN bonds and enable ALD on low temperature substrates. Atomic force microscopy showed that the root mean square roughness in the high Ar dilution sample was 0.093 nm, indicating high flatness.

Emission cross sections for energetic O+(4S,2D,2P)–N2 collisions

Measurements of emission cross sections for the [Formula: see text] collision system with the incident beam of 1–10 keV [Formula: see text] in the ground [Formula: see text]) and metastable [Formula: see text] and [Formula: see text] states are reported. The emission cross section induced by incident ions in the metastable state [Formula: see text] is much larger than that for the ground [Formula: see text] state. The emission cross section of [Formula: see text] ion for [Formula: see text], [Formula: see text], and [Formula: see text] bands system is measured and the ratio of intensities for these bands is established as [Formula: see text] It is shown that the cross sections for the [Formula: see text] ions emissions in the dissociative charge exchange processes increase with the increase of the incident ion energy. The energy dependence of the emission cross section of the band [Formula: see text] [Formula: see text] nm of the first-negative band system of the [Formula: see text] and degree of linear polarization of emission in [Formula: see text] collision are measured for the first time. An influence of an admixture of the ion metastable state on a degree of linear polarization is revealed. The mechanism of the processes realized during collisions of ground and metastable oxygen ions on molecular nitrogen have been established. It is demonstrated that for [Formula: see text] collision system the degree of linear polarization by metastable [Formula: see text] ions is less compared to those that are in the ground [Formula: see text] state and the sign of emission of degree of linear polarization of excited molecular ions does not change.

Atmospheric Plasma-Enhanced Spatial Chemical Vapor Deposition of SiO2 Using Trivinylmethoxysilane and Oxygen Plasma

SiO2 constitutes one of the most widely used dielectric materials in the microelectronics, packaging, and optical industries. Therefore, the development of new processes to deposit SiO2 at low temperature and in an affordable and scalable way are desirable. In this work, we present a low-temperature, open-air process based on spatial atomic layer deposition (SALD) that yields high purity SiO2 films at temperatures down to room temperature. The films were obtained by operating our SALD system in CVD mode (i.e., allowing precursor crosstalk), using an oxygen plasma in combination with trivinylmethoxysilane (TVMS). TVMS is an appealing precursor since it is highly volatile, is affordable, and does not contain halogen elements, thus being very suitable for application in atmospheric-pressure spatial deposition systems. Conversely, water, oxygen, hydrogen peroxide, or ozone did not show any reactivity with TVMS at temperatures up to 260 °C. Thus, when operating our system in ALD mode, no film could be obtained due to the lack of reactivity of the precursor with OH* surface groups. 3D printing was employed to fabricate custom heads integrating both the precursor injector and the atmospheric plasma generator. Our results show that conformal SiO2 thin films can be deposited by our atmospheric plasma-enhanced spatial chemical vapor deposition (APE-SCVD) approach at low temperatures (RT–180 °C) on different substrates, including silicon wafers, microglass slides, or even polymeric substrates with a high growth rate up to 2–5 nm/min. The deposition rate increased when increasing the power applied to the plasma reactor but decreased when increasing the deposition temperature due to the faster decay of the metastable oxygen radical species. FTIR results showed no differences for films deposited with different plasma powers. Conversely, temperature had an effect on the ratio between the AS1 and the AS2 bands. Even though the deposition of SiO2 was carried out at low temperatures in the open air using a metalorganic precursor, no contamination from SiNx or SiCx was observed by FTIR and XPS measurements. Our results open the door to the low-temperature, fast printing of Si-based devices.

FTIR spectra of NaTe and KTe and ab initio calculations of the electronic structure of these molecules

Gas phase emission spectra of the hitherto unknown radicals NaTe and KTe have been measured in the NIR range with a Fourier-transform spectrometer. The emissions were observed from a fast-flow system in which tellurium vapor in argon carrier gas was passed through a microwave discharge and mixed with sodium or potassium vapor in an observation tube. Excitation of the radicals mostly occurred by near-resonant E-E energy exchange from added metastable oxygen O2(a1Δg). Like for the previously studied LiTe molecule, for both radicals two systems of blue-degraded bands were measured in the range 4500–8500 cm−1. They were assigned to the transitions A2Σ+(A1/2) → X12Π3/2(X13/2) and A2Σ+(A1/2) → X22Π 1/2(X21/2). For all four subsystems vibrational analyses were performed which yielded ground state splittings of 2265.39(13) cm−1 (NaTe) and 1544.19(11) cm−1 (KTe) as well as A2Σ+ state energies of 7935.98(9) cm−1 (NaTe) and 6404.71(11) cm−1 (KTe) and vibrational constants of the X13/2, X21/2 and A1/2 states of both molecules. The 0-0 bands of both sub-transitions of NaTe were measured at high spectral resolution and rotationally analyzed.In order to aid in the analysis of the experimental data, a series of relativistic configuration interaction calculations has been carried out to obtain potential curves for the low-lying states of NaTe and KTe and also electric dipole transition moments connecting them.

Gas temperature measurements in a pulsed, low-pressure inductively coupled plasma in oxygen

Optical emission spectroscopy (OES) of the magnetic dipole allowed O2(b1Σg+) to O2(X3Σg−) transition was investigated as a non-intrusive gas temperature diagnostic for E-mode and H-mode inductively coupled plasmas (ICP) in oxygen. It was compared to tunable diode laser absorption spectroscopy using Ar admixtures, and OES of the nitrogen Second Positive System with nitrogen admixtures. O2 OES provided accurate results for the E-mode ICP, 400–600 K for powers of 100–300 W, but in H-mode the method was unsuitable probably because of excitation of O2(b1Σg+) by metastable atomic oxygen. Rotational temperatures were measured, using N2 OES with N2 admixtures, for pulsed operation of the ICP with a 30 ms pulse duration and 15% duty cycle. It took 1–3 ms before the steady-state rotational temperatures were achieved. In addition, a small variation of matching network settings affects the plasma ignition delay time by several ms.

Metastable oxygen vacancy ordering state and improved memristive behavior in TiO2 crystals

Oxygen vacancy is one of the pivotal factors for tuning/creating various oxide properties. Understanding the behavior of oxygen vacancies is of paramount importance. In this study, we identify a metastable oxygen vacancy ordering state other than the well-known Magnéli phases in TiO2 crystals from both experimental and theoretical studies. The oxygen vacancy ordering is found to be a zigzag chain along the [0 0 1] direction in the (1 1 0) plane occurring in a wide temperature range of 200–500 °C. This metastable ordering state leads to a first-order phase transition accompanied by significant enhancement of dielectric permittivity and a memristive effect featuring a low driving electric field. Our results can improve oxide properties by engineering oxygen vacancies.