Metal Microneedles Research Articles

Drug delivery device for the inner ear: ultra-sharp fully metallic microneedles.

Drug delivery into the inner ear is a significant challenge due to its inaccessibility as a fluid-filled cavity within the temporal bone of the skull. The round window membrane (RWM) is the only delivery portal from the middle ear to the inner ear that does not require perforation of bone. Recent advances in microneedle fabrication enable the RWM to be perforated safely with polymeric microneedles as a means to enhance the rate of drug delivery from the middle ear to the inner ear. However, the polymeric material is not biocompatible and also lacks the strength of other materials. Herein we describe the design and development of gold-coated metallic microneedles suitable for RWM perforation. When developing microneedle technology for drug delivery, we considered three important general attributes: (1) high strength and ductility material, (2) high accuracy and precision of fabrication, and (3) broad design freedom. We developed a hybrid additive manufacturing method using two-photon lithography and electrochemical deposition to fabricate ultra-sharp gold-coated copper microneedles with these attributes. We refer to the microneedle fabrication methodology as two-photon templated electrodeposition (2PTE). We demonstrate the use of these microneedles by inducing a perforation with a minimal degree of trauma in a guinea pig RWM while the microneedle itself remains undamaged. Thus, this microneedle has the potential literally of opening the RWM for enhanced drug delivery into the inner ear. Finally, the 2PTE methodology can be applied to many different classes of microneedles for other drug delivery purposes as well the fabrication of small scale structures and devices for non-medical applications. Graphical Abstract Fully metallic ultra-sharp microneedle mounted at end of a 24-gauge stainless steel blunt syringe needle tip: (left) Size of microneedle shown relative to date stamp on U.S. one-cent coin; (right) Perforation through guinea pig round window membrane introduced with microneedle.

Solid and hollow metallic glass microneedles for transdermal drug-delivery

Metallic microneedles are attractive for painless transdermal drug-delivery. However, fabrication techniques for metal microneedles are often complex and multi-step. In this study, a scalable manufacturing of metallic microneedle arrays is presented using thermoplastic drawing of metallic glasses. Microneedles with tunable lengths and tips are produced by controlling the rheology and fracture of metallic glass. The same drawing process can generate solid and hollow microneedles simply by varying the thickness of metallic glass. The mechanism of thickness dependent transition from solid to hollow profiles is described by the viscous buckling of metallic liquid. In vitro skin insertion tests demonstrate that both solid and hollow metallic glass microneedles can pierce porcine skin and deliver model drugs.

Improved Biosafety and Transdermal Delivery of Aconitine via Diethylene Glycol Monoethyl Ether-Mediated Microemulsion Assisted with Microneedles.

In the current study, diethylene glycol monoethyl ether-mediated microemulsions were combined with microneedles for enhanced transdermal aconitine delivery. The oil-in-water microemulsion increasedaconitine solubility and enhanced transdermal drug delivery and assistance with metal microneedles enhanced permeation of the aconitine-loaded microemulsion. Carried by the microemulsion, the in vitro permeability of aconitine was significantly enhanced, and further improved using microneedles. In vivo microdialysis revealed that the subcutaneous local drug concentration reached a high level within 30 min and remained relatively consistent to the end of the experimental period. AUC0-t of the microemulsion group was significantly higher than that of the aqueous solution group, and the microemulsion combined with microneedles group achieved the highest AUC0-t among the tested groups. The microemulsion and microdialysis probe also showed good biocompatibility with skin tissue. The microemulsion could be internalized by HaCaT and CCC-ESF-1 cells via lysosomes. The in vitro cytotoxicity of aconitine toward skin cells was reduced via encapsulation by microemulsion, and the prepared microemulsion developed no skin irritation. Hence, transdermal aconitine delivery and drug biosafety were effectively improved by loading into the microemulsion and assisting with microneedles, and in vivo microdialysis technique is suitable for realtime monitoring of transdermal drug delivery with microemulsion-based drug vehicles.

Clinical Evaluation of a Novel Micro-lancet (ML) for Minimizing Lancing Pain

Patients with diabetes are required to lance their fingers daily for self-monitoring their blood glucose level. Patients might be reluctant to use commercial lancets with thick outer diameters due to lancing pain; this results in the worsening of their health. A metallic microneedle is an ideal substitute to the commercial lancet system and offers a minimally invasive and patient friendly approach for capillary blood extraction. However, reports regarding the performance of sufficient long and high stiffness microneedles for innocuous and efficient capillary blood sampling for conducting clinical trials are rare. Here, we developed a novel micro-lancet (ML) that is 3 mm long and has a 130 µm outer diameter and a sharp beveled 15° tip. ML induced lesser tissue damage than the commercial ACCU-CHEK Softclix in a porcine skin test. Through a clinical study, we demonstrated that the pain scores using the commercial lancet and ML were 3.4 and 0.8 the numeric pain rating scale, respectively. The average blood volume drawn using the ML was 0.96 µL, which satisfies the minimum requirement (0.3 µL) for glucose detection. This novel ML may improve patient compliance to blood glucose monitoring procedures by reducing lancing-related pain.

Fabrication of Hollow Metal Microneedle Arrays Using a Molding and Electroplating Method

ABSTRACT:The need for hollow microneedle arrays is important for both drug delivery and wearable sensor applications; however, their fabrication poses many challenges. Hollow metal microneedle arrays residing on a flexible metal foil substrate were created by combining additive manufacturing, micromolding, and electroplating approaches in a process we refer to as electromolding. A solid microneedle with inward facing ledge was fabricated with a two photon polymerization (2PP) system utilizing laser direct write (LDW) and then molded with polydimethylsiloxane. These molds were then coated with a seed layer of Ti/Au and subsequently electroplated with pulsed deposition to create hollow microneedles. An inward facing ledge provided a physical blocking platform to restrict deposition of the metal seed layer for creation of the microneedle bore. Various ledge sizes were tested and showed that the resulting seed layer void could be controlled via the ledge length. Mechanical properties of the PDMS mold was adjusted via the precursor ratio to create a more ductile mold that eliminated tip damage to the microneedles upon removal from the molds. Master structures were capable of being molded numerous times and molds were able to be reused. SEM/EDX analysis showed that trace amounts of the PDMS mold were transferred to the metal microneedle upon removal. The microneedle substrate showed a degree of flexibility that withstood over 100 cycles of bending from side to side without damaging. Microneedles were tested for their fracture strength and were capable of puncturing porcine skin and injecting a dye.

Protection of Nanostructures-Integrated Microneedle Biosensor Using Dissolvable Polymer Coating.

Real-time transdermal biosensing provides a direct route to quantify biomarkers or physiological signals of local tissues. Although microneedles (MNs) present a mini-invasive transdermal technique, integration of MNs with advanced nanostructures to enhance sensing functionalities has rarely been achieved. This is largely due to the fact that nanostructures present on MNs surface could be easily destructed due to friction during skin insertion. In this work, we reported a dissolvable polymer-coating technique to protect nanostructures-integrated MNs from mechanical destruction during MNs insertion. After penetration into the skin, the polymer could readily dissolve by interstitial fluids so that the superficial nanostructures on MNs could be re-exposed for sensing purpose. To demonstrate this technique, metallic and resin MNs decorated with vertical ZnO nanowires (vNWs) were employed as an example. Dissolvable poly(vinyl pyrrolidone) was spray-coated on the vNW-MNs surface as a protective layer, which effectively protected the superficial ZnO NWs when MNs penetrated the skin. Transdermal biosensing of H2O2 biomarker in skin tissue using the polymer-protecting MNs sensor was demonstrated both ex vivo and in vivo. The results indicated that polymer coating successfully preserved the sensing functionalities of the MNs sensor after inserting into the skin, whereas the sensitivity of the MN sensor without a coating protection was significantly compromised by 3-folds. This work provided unique opportunities of protecting functional nanomodulus on MNs surface for minimally invasive transdermal biosensing.

Evaluation of a Particulate Breast Cancer Vaccine Delivered via Skin.

Breast cancer impacts female population globally and is the second most common cancer for females. With various limitations and adverse effects of current therapies, several immunotherapies are being explored. Development of an effective breast cancer vaccine can be a groundbreaking immunotherapeutic approach. Such approaches are being evaluated by several clinical trials currently. On similar lines, our research study aims to evaluate a particulate breast cancer vaccine delivered via skin. This particulate breast cancer vaccine was prepared by spray drying technique and utilized murine breast cancer whole cell lysate as a source of tumor-associated antigens. The average size of the particulate vaccine was 1.5μm, which resembled the pathogenic species, thereby assisting in phagocytosis and antigen presentation leading to further activation of the immune response. The particulate vaccine was delivered via skin using commercially available metal microneedles. Methylene blue staining and confocal microscopy were used to visualize the microchannels. The results showed that microneedles created aqueous conduits of 50 ± 10μm to deliver the microparticulate vaccine to the skin layers. Further, an in vivo comparison of immune response depicted significantly higher concentration of serum IgG, IgG2a, and B and T cell (CD4+ and CD8+) populations in the vaccinated animals than the control animals (p< 0.001). Upon challenge with live murine breast cancer cells, the vaccinated animals showed five times more tumor suppression than the control animals confirming the immune response activation and protection (p< 0.001). This research paves a way for individualized immunotherapy following surgical tumor removal to prolong relapse episodes.

Metallic microneedles with interconnected porosity: A scalable platform for biosensing and drug delivery

Metallic-based microneedles (MNs) offer a robust platform for minimally invasive drug delivery and biosensing applications due to their mechanical strength and proven tissue and drug compatibility. However, current designs suffer from limited functional surface area or challenges in manufacturing scalability. Here, porous 316L stainless steel MN patches are proposed. Fabricated through a scalable manufacturing process, they are suitable for storage and delivery of drugs and rapid absorption of fluids for biosensing. Fabrication of these MNs involves hot embossing a patch of stainless steel-based feedstock, sintering at 1100 °C and subsequent electropolishing. Optimisation of this manufacturing process yields devices that maintain mechanical integrity yet possess high surface area and associated porosity (36%) to maximise loading capacity. Similarly, a small pore size has been targeted (average diameter 2.22 μm, with 90% between 1.56 μm and 2.93 μm) to maximise capillarity and loading efficiency. This porous network has a theoretical wicking rate of 4.7 μl/s and can wick-up 27 ± 5 μl of fluid through capillary action which allows for absorption of pharmaceuticals for delivery. When inserted into a metabolite-loaded skin model, the MNs absorbed and recovered 17 ± 3 μl of the metabolite solution. The drug delivery performance of the porous metallic MNs (22.4 ± 4.9 µg/cm2) was found to be threefold higher than that of topical administration (7.1 ± 4.3 µg/cm2). The porous metallic MN patches have been shown to insert into porcine skin under a 19 N load. These results indicate the potential of design-for-manufacturing porous stainless steel MNs in biosensing and drug delivery applications. Statement of SignificanceMicroneedles are micro-scale sharp protrusions used to bypass the stratum corneum, the skin’s outer protective layer, and painlessly access dermal layers suitable for drug delivery and biosensing. Despite a depth of research in the area we have not yet seen large-scale clinical adoption of microneedle devices. Here we describe a device designed to address the potential barriers to adoption seen by other microneedles devices. We have developed a scalable, cost effective process to produce medical grade stainless steel microneedle patches which passively absorb and store drugs or interstitial fluid though a porous network and capillary action. This device, with low manufacturing and regulatory burdens may help the large-scale adoption of microneedles.

Hepatitis B vaccination using a dissolvable microneedle patch is immunogenic in mice and rhesus macaques.

Chronic Hepatitis B virus infection remains a major global public health problem, accounting for about 887,000 deaths in 2015. Perinatal and early childhood infections are strongly associated with developing chronic hepatitis B. Adding a birth dose of the hepatitis B vaccine (HepB BD) to routine childhood vaccination can prevent over 85% of these infections. However, HepB BD coverage remains low in many global regions, with shortages of birth attendants trained to vaccinate and limited HepB BD supply at birth. To address the challenges, we developed coated metal microneedle patches (cMNPs) and dissolvable microneedle patches (dMNPs) that deliver adjuvant‐free hepatitis B vaccine to the skin in a simple‐to‐administer manner. The dMNP contains micron‐scale, solid needles encapsulating vaccine antigen and dissolve in the skin, generating no sharps waste. We delivered HepB BD via cMNP to BALB/c mice and via dMNP to both mice and rhesus macaques. Both cMNP and dMNP were immunogenic, generating hepatitis B surface antibody levels similar to human seroprotection. Biomechanical analysis showed that at high forces the microneedles failed mechanically by yielding but microneedles partially blunted by axial compression were still able to penetrate skin. Overall, this study indicates that with further development, dMNPs could offer a method of vaccination to increase HepB BD access and reduce needle waste in developing countries.

Analysis of Process Parameters and Performance Test for Fabricating Stainless-steel Metal Microneedles

Analysis of Process Parameters and Performance Test for Fabricating Stainless-steel Metal Microneedles

Fabrication of Circular Obelisk-Type Multilayer Microneedles Using Micro-Milling and Spray Deposition.

In this study we present the fabrication of multilayer microneedles with circular obelisk and beveled-circular obelisk geometries, which have potential applications in implantable drug delivery devices. Micro-milling was adopted as an environmental-friendly and cost-effective way to fabricate primary metal microneedle masters. Polylactic acid (PLA) microneedles with sharp tips were then obtained by micromolding followed by oxygen plasma etching and used for preparing polydimethylsiloxane (PDMS) microneedle molds. A spray deposition process was employed for microneedle fabrication to facilitate the formation of multilayer microneedles while helping in maintenance of drug stability. Multilayer microneedles were successfully formed by sequential spraying of poly(lactic-co-glycolic acid) (PLGA) and polyvinylpyrrolidone (PVP) solutions into the mold. The fabricated PLGA-PVP multilayer microneedles penetrated the pig cadaver skin without breakage and released dyes in the skin at different rates, which reveals the potential for implantable microneedles enabling controlled release. Mechanical testing demonstrated that the obelisk-shaped microneedles were mechanically stronger than a pyramid-shaped microneedle and suggested that strong adhesion between PLGA and PVP layers was achieved as well. Structural stability and functionality of a model drug, horseradish peroxidase (HRP), upon spray deposition was examined using circular dichroism (CD) spectroscopy and enzyme activity assay. HRP retained its secondary structure and activity in PVP, whereas HRP in PLGA showed structural changes and reduced activity. Combination of micro-milling and spray deposition would be an attractive way of fabricating drug-containing polymer microneedles with various geometries while reducing prototyping time and process-induced drug instability.

Porous polymer coatings on metal microneedles for enhanced drug delivery.

We present a simple method to coat microneedles (MNs) uniformly with a porous polymer (PLGA) that can deliver drugs at high rates. Stainless steel (SS) MNs of high mechanical strength were coated with a thin porous polymer layer to enhance their delivery rates. Additionally, to improve the interfacial adhesion between the polymer and MNs, the MN surface was modified by plasma treatment followed by dip coating with polyethyleneimine, a polymer with repeating amine units. The average failure load (the minimum force sufficient for detaching the polymer layer from the surface of SS) recorded for the modified surface coating was 25 N, whereas it was 2.2 N for the non-modified surface. Calcein dye was successfully delivered into porcine skin to a depth of 750 µm by the porous polymer-coated MNs, demonstrating that the developed MNs can pierce skin easily without deformation of MNs; additional skin penetration tests confirmed this finding. For visual comparison, rhodamine B dye was delivered using porous-coated and non-coated MNs in gelatin gel which showed that delivery with porous-coated MNs penetrate deeper when compared with non-coated MNs. Finally, lidocaine and rhodamine B dye were delivered in phosphate-buffered saline (PBS) medium by porous polymer-coated and non-coated MNs. For rhodamine B, drug delivery with the porous-coated MNs was five times higher than that with the non-coated MNs, whereas 25 times more lidocaine was delivered by the porous-coated MNs compared with the non-coated MNs.

Design considerations of a hollow microneedle-optofluidic biosensing platform incorporating enzyme-linked assays

A hollow metallic microneedle is integrated with microfluidics and photonic components to form a microneedle-optofluidic biosensor suitable for therapeutic drug monitoring (TDM) in biological fluids, like interstitial fluid, that can be collected in a painless and minimally-invasive manner. The microneedle inner lumen surface is bio-functionalized to trap and bind target analytes on-site in a sample volume as small as 0.6 nl, and houses an enzyme-linked assay on its 0.06 mm2 wall. The optofluidic components are designed to rapidly quantify target analytes present in the sample and collected in the microneedle using a simple and sensitive absorbance scheme. This contribution describes how the biosensor components were optimized to detect in vitro streptavidin-horseradish peroxidase (Sav-HRP) as a model analyte over a large detection range (0–7.21 µM) and a very low limit of detection (60.2 nM). This biosensor utilizes the lowest analyte volume reported for TDM with microneedle technology, and presents significant avenues to improve current TDM methods for patients, by potentially eliminating blood draws for several drug candidates.

Microneedle-assisted transdermal delivery of acetylsalicylic acid (aspirin) from biopolymer films extracted from fish scales

This study investigates the transdermal release of aspirin (ASA) from films of hydrolyzed collagen obtained from fish scales. The patches were made with 0.2 g of ASA dissolved in 99% ethanol and 1.98 g of the extracted fish scale biopolymer (FSBP) dissolved in 10 mL distilled water which is then dried. Porcine skin is pre-treated with solid metal microneedles. ASA-loaded FSBP patch is then applied. The skin samples were placed on diffusion cells. Samples were taken at varying times: 5, 24, and 48 h and tested for the presence of ASA using UV spectrometry-based method introduced in this study. The results obtained showed that for all repeated study, no ASA was detected in the receiver compartment after 5 h. After 24 h up to 0.24 mg/mL ASA had released into the receiver compartment; and after 48 h, a concentration 0.74 mg/mL had been reached for skin samples treated with microneedles. ASA was not detected in the receiver compartment for skin samples that were not pre-treated with microneedles after 5 h. After 24 h, the concentration of 0.04 mg/mL was recorded, and at 48 h, concentration of 0.045 mg/mL was detected. This study presents for the first time transdermal drug delivery (TDD) films made of FSBP applied as drug delivery films for ASA and the use of microneedles to significantly enhance the release of ASA from the ASA-FSBP TDD films using the ‘poke and patch’ method. We also present a novel method for testing ASA in the TDD study using reaction with ferrous gluconate.

Formulation of hydrophobic peptides for skin delivery via coated microneedles

Microneedles (MNs) have been investigated as a minimally-invasive delivery technology for a range of active pharmaceutical ingredients (APIs). Various formulations and methods for coating the surface of MNs with therapeutics have been proposed and exemplified, predominantly for hydrophilic drugs and particulates. The development of effective MN delivery formulations for hydrophobic drugs is more challenging with dosing restrictions and the use of organic solvents impacting on both the bioactivity and the kinetics of drug release. In this study we propose a novel formulation that is suitable for MN coating of hydrophobic auto-antigen peptides currently being investigated for antigen specific immunotherapy (ASI) of type 1 diabetes. The formulation, comprising three co-solvents (water, 2-methyl-2-butanol and acetic acid) and polyvinylalcohol 2000 (PVA2000) can dissolve both hydrophilic and hydrophobic peptide auto-antigens at relatively high, and clinically relevant, concentrations (25mg/ml or 12.5mg/ml). The drug:excipient ratio is restricted to 10:1 w/w to maximise dose whilst ensuring that the dry-coated payload does not significantly impact on MN skin penetration performance. The coating formulation and process does not adversely affect the biological activity of the peptide. The delivery efficiency of the coated peptide into skin is influenced by a number of parameters. Electropolishing the metal MN surface increases delivery efficiency from 2.0±1.0% to 59.9±6.7%. An increased mass of peptide formulation per needle, from 0.37μg to 2μg peptide dose, resulted in a thicker coating and a 20% reduction in the efficiency of skin delivery. Other important performance parameters for coated MNs include the role of excipients in assisting dissolution from the MNs, the intrinsic hydrophobicity of the peptide and the species of skin model used in laboratory studies. This study therefore both exemplifies the potential of a novel formulation for coating hydrophobic and hydrophilic peptides onto MN devices and provides new insight into the factors that influence delivery efficiency from coated MNs. Importantly, the results provide guidance for identifying critical attributes of the formulation, coating process and delivery device, that confer reproducible and effective delivery from coated MNs, and thus contribute to the requirements of the regulators appraising these devices.

Pretreatment with Microneedle Array to Improve the Nail Permeability

The objective was to investigate the feasibility of pretreatment with solid microneedles as an approach to improve the nail permeability to drugs. In vitro permeation studies were performed across the human nail plates which were pretreated with solid titanium microneedles (0.5 mm). Human nail plates without pretreatment were used as a control. Sodium fluorescein was used as a model dye. Microscopic studies were performed to visualize the distribution of sodium fluorescein in the nail plate. The amount of sodium fluorescein permeated in the receiver compartment after 7 days of studies was found to be ~123 fold more compared to control. The amount of sodium fluorescein retained in active and peripheral diffusion areas of nail plate was found to be ~4 fold and ~3 fold more relative to control. Overall, pre-treatment of the nail plate with metal microneedles is appeared to be feasible approach to deliver a significant amount of drugs into and across the nail plate.

Microneedles As a Delivery System for Gene Therapy.

Gene delivery systems can be divided to two major types: vector-based (either viral vector or non-viral vector) and physical delivery technologies. Many physical carriers, such as electroporation, gene gun, ultrasound start to be proved to have the potential to enable gene therapy. A relatively new physical delivery technology for gene delivery consists of microneedles (MNs), which has been studied in many fields and for many molecule types and indications. Microneedles can penetrate the stratum corneum, which is the main barrier for drug delivery through the skin with ease of administration and without significant pain. Many different kinds of MNs, such as metal MNs, coated MNs, dissolving MNs have turned out to be promising in gene delivery. In this review, we discussed the potential as well as the challenges of utilizing MNs to deliver nucleic acids for gene therapy. We also proposed that a combination of MNs and other gene delivery approaches may lead to a better delivery system for gene therapy.

Evaluation of microparticulate ovarian cancer vaccine via transdermal route of delivery

Ovarian cancer is the fifth most commonly occurring malignancy in women, with the highest mortality rate among all the gynecological tumors. Microparticulate vaccine can serve as an immunotherapeutic approach with a promising antigenic delivery system without a need for conventional adjuvants. In this study, a microparticulate vaccine using whole cell lysate of a murine ovarian cancer cell line, ID8 was prepared by spray drying. Further, the effect of interleukins (ILs) such as IL-2 and IL-12 was evaluated in a separate study group by administering them with vaccine particles to enhance the immune response. The vaccine microparticles were administered to C57BL/6 female mice via transdermal alone and in combination with the oral route. The transdermal vaccine was delivered using a metallic microneedle device, AdminPen™. Orally administered microparticles also included an M-cell targeting ligand, Aleuria aurantia lectin, to enhance the targeted uptake from microfold cells (M-cells) in Peyer's patches of small intestine. In case of combination of routes, mice were given 5 transdermal doses and 5 oral doses administered alternatively, beginning with transdermal dose. At the end of vaccination, mice were challenged with live tumor cells. Vaccine alone resulted in around 1.5 times tumor suppression in case of transdermal and combination of routes at the end of 15th week when compared to controls. Inclusion of interleukins resulted in 3 times tumor suppression when administered with transdermal vaccine and around 9 times tumor suppression for the combination route of delivery in comparison to controls. These results were further potentiated by serum IgG, IgG1 and IgG2a titers. Moreover, CD8+ T-cell, CD4+ T-cell and NK (natural killer) cell populations in splenocytes were elevated in case of vaccinated mice. Thus, vaccine microparticles could trigger humoral as well as cellular immune response when administered transdermally and via combination of route of delivery. However overall, vaccine administered with interleukins, via combination of route, was found to be the most efficacious to suppress the tumor growth and lead to a protective immune response.

鍍金による金属製マイクロ針の開発

鍍金による金属製マイクロ針の開発

Inkjet printing of insulin microneedles for transdermal delivery.

Inkjet printing technology was used to apply insulin polymeric layers on metal microneedles for transdermal delivery. A range of various polymers such as gelatin (GLN), polyvinyl caprolactame-polyvinyl acetate-polyethylene glycol (SOL), poly(2-ethyl-2-oxazoline) (POX) and trehalose (THL) were assessed for their capacity to form thin uniform and homogeneous layers that preserve insulin intact. Atomic force microscopy (AFM) showed homogeneous insulin-polymer layers without any phase separation while SOL demonstrated the best performance. Circular discroism (CD) analysis of rehydrated films showed that insulin's alpha helices and β-sheet were well preserved for THL and SOL. In contrast, GLN and POX insulin layers revealed small band shifts indicating possible conformational changes. Insulin release in Franz diffusion cells from MNs inserted into porcine skin showed rapid release rates for POX and GLN within the first 20min. Inkjet printing was proved an effective approach for transdermal delivery of insulin in solid state.