Median Particle Size Research Articles

Effect of process parameter on the flowability of nanocrystalline CoNiCrAlY powder synthesized by mechanical milling

The present study concerns understanding the effect of process parameters on the characteristics and flowability of nanocrystalline CoNiCrAlY powder synthesized by mechanical milling. Mechanical milling has been conducted in a planetary ball mill with tungsten carbide (WC) ball, with ball to powder ratio of 10:1 at 300 rpm speed, using 1% stearic acid and toluene as process control agent (PCA) with time varying from 10 h to 36 h. The synthesized nanocrystalline powder were characterized by Scanning Electron Microscopy, X-ray Diffraction technique, X-ray Photoelectron Spectroscopy, and Differential Scanning Calorimetry. Subsequently, flowability in terms of Hausner ratio was assessed by Tap Density Tester. Average particle size of the powder was found to decrease from 33 μm to 22 μm after 10 h of milling and further increases to 43 μm and 38 μm after 25 and 36 h of milling, respectively, in stearic acid medium. However, in toluene medium particle size continuously decreases from 33 μm to 9.7 μm with increasing milling time. The particle morphology changes from spherical to platelet shape at low milling hours in both of the media. After 25 h of milling, the shape of the particles is nearly spherical for stearic acid and irregular for toluene used as a PCA. Crystallize size was found to decrease with increasing milling time from 147 nm to 7.7 nm and to 6.4 nm in stearic acid and toluene media, respectively. There was presence of γ, γʹ, β, hcp-Co, Al2O3 and AlOOH phases on the powder particles milled in both the medium. The measured Hausner ratio of the powders was found to vary from 1.18 to 1.32 in stearic acid medium, and was found to increase with increasing milling time. On the other hand, in toluene media flowability decreases (Hausner ratio increases from 1.33 to 1.44) with increasing milling time.

Exploring the maximum nitrite production rate through the granular sludge-type reactor to match the needs of anammox process realizing efficient nitrogen removal

The reliable and efficient nitrite production rate (NPR) through nitritation process is the prerequisite for the efficient running of subsequent processes, like the anammox process and the nitrite shunt. However, there has been scant research on stable and productive nitritation process in recent years. In this study, at a stable hydraulic retention time of 12.0 h and with precise and strict DO control, the upper limit of the NPR was initially investigated using a continuous-flow granular sludge reactor. The NPR of 1.69 kg/m3/d with a nitrite production efficiency of 81.97% was finally achieved, which set a record until now in similar research. The median sludge particle size of 270.0 μm confirmed the development of clearly defined granular sludge. The genus Nitrosomonas was the major ammonium oxidizing bacteria. In conclusion, this study provides valuable insights for the practical application of the effective nitritation process driving subsequent nitrogen removal processes.

Study on mechanism of particle aggregation and pore formation during loess air-fall deposition based on discrete element method

The pore structure of aeolian deposits is essential for predicting their mechanical properties and the climatic conditions during their deposition. The discrete element method (DEM) is a practical approach for analysing the formation and evolution mechanisms of aeolian deposits’ pore structure. However, the effect of particle shape and non-contact van der Waals force on deposits’ pore structure with different particle sizes needs further exploration to enhance the efficiency and accuracy of DEM simulations. We developed a VdwForce model for DEM that accounts for the van der Waals force’s long-tail effect, and we conducted loess air-fall numerical tests that matched laboratory simulation tests. DEM simulations and laboratory tests show that the deposits’ porosity increased as the median particle size decreased, whether using spherical or actual shape particles in simulations. When deposits formed by particles with actual shapes have dense packing structures, simulations utilising spherical particles of the same size produce larger porosities. The primary reason of the alteration in the pore structure of the loess air-fall deposits is the shift in the quantity and pattern of particle agglomerates caused by van der Waals attractive force. So, the aggregation process during air-fall was essential for forming overhead pore structures.

Estimating sediment transport capacity on sloping farmland on the Loess Plateau considering soil particle size characteristics

The sediment transport capacity (Tc) is essential for understanding soil erosion and creating soil erosion prediction models. Although many Tc equations exist, they are not universally applicable to sloping farmland on the Loess Plateau. To tailor Tc equations for this region, Tc for four soils (Shenmu Inceptisol (SMI), Shenmu Entisol (SME), Ansai Inceptisol (AS), and Yongshou Alfisol (YS)) from sloping farmland on the Loess Plateau was determined through flume tests with slopes ranging from 15.84 % to 38.39 % and flow discharges of 0.05 to 0.11 m2 min−1. Additionally, appropriate particle size characteristics were selected to distinguish the soil types. The results revealed that the Tc of SME exceeded that of YS, followed by SMI and AS in descending order. The Tc of the four individual soils increased exponentially with flow discharge (Q) and slope (S). Tc for individual soils could be satisfactorily predicted using power functions of mean velocity, shear stress (τ), stream power (ω), or effective stream power (R2: 0.661–0.950, MAE: 0.020–0.110, RMSE: 0.023–0.151), with ω being identified as an optimal hydraulic parameter for simulating Tc. In contrast, the unit stream power was a poor predictor of Tc for individual soils (R2: 0.403–0.700, MAE: 0.035–0.123, RMSE: 0.040–0.161). The median particle size (D50), sorting coefficient, and kurtosis (Kg) exhibited highly significant positive correlations with Tc (P < 0.01). Finally, a quadratic power equation for Q, S, D50, and Kg, along with two ternary power equations for ω (or τ), D50, and Kg were newly constructed, all with satisfactory accuracies (R2: 0.808–0.826, MAE: 0.061–0.063, RMSE: 0.086–0.090). The inclusion of σ and Kg rectified the inaccuracies in predicting Tc for all four soils using Q and S equations or ω (or τ). The results of this study offer valuable insights into the construction of the Tc equations.

Study on Plugging the Multiscale Water Channeling in Low-Permeability Heterogeneous Porous Media Based on the Growth of Bacteria

Summary To promote the effect of waterflooding of a heterogeneous low-permeability reservoir in the Ordos Basin, a microbial plugging agent is developed to plug the multiscale water channeling. Based on the characteristics of the growth of bacteria, the microbial plugging agent can plug both porous media and microfractures with different scales. The microbial plugging agent is prepared by activating the native bacteria present in low-permeability reservoirs by using the fermentation nutrients. After growing in the fermentation nutrient solution for 4 days in a beaker, the growth of microbial strains begins to stabilize. After that, the main particle size of the prepared microbial plugging agent is between 40 μm and 160 μm and the median particle size (D50) is near 90 μm. The microbial plugging agent has good shear resistance, salt resistance, and stability. At the initial state, due to good injectivity, the microbial plugging agent can smoothly enter into a low-permeability core, a heterogeneous core, and a fractured core, respectively. Thus, it can grow and reproduce in the cores. Based on the characteristics of growth, it can match with the spatial scale of pore or fracture in the cores, so that it cannot only plug the porous media water channeling with different scales but also plug the microfracture water channeling with different scales. This phenomenon has been confirmed by microscopic visualization flow experiments and core flow experiments. The developed microbial plugging agent can be applied to plug the multiscale water channeling to enhance oil recovery of low-permeability heterogeneous reservoirs.

Fragmentation and reorganization of agglomerates in catalyst inks: Understanding the time-scale and temperature-dependent effects on the dispersion process

The time and temperature of the dispersive shear process of catalyst inks have a great influence on the agglomerate structure of the ink and the rheological properties of the ink. In this paper, three different catalyst inks were prepared at 20 °C, 30 °C and 40 °C, and tested using characterization such as rheological techniques, zeta (ξ) potential, and particle size measurements. As the temperature rises, the median particle size inside the ink at the end of shear was 400, 308.05 and 157.3 nm, and the zeta potential was −37, −33 and −25 mV, with a decrease in viscosity and a deterioration in thixotropy. The catalyst layers prepared from inks dispersed at different temperatures had the smallest cracks and the flattest surface at 30 °C, and the largest cracks, the largest contact angle, the roughest surface, and the poorest polarization properties at 40 °C. Through the comprehensive analysis of the experimental data, the fragmentation and reorganization processes of agglomerates during the internal dispersion of catalyst ink were revealed from the perspectives of time scale and temperature variation, respectively. This study provides an experimental basis for a deeper understanding of the dispersion performance of catalyst ink at different temperatures.

Microstructural evolution and carbides precipitation behavior and their effects on mechanical property of Nb–Ti microalloyed FB590 steel

Ferrite-bainite dual phase steels have been widely used in automobile manufacturing industry due to their high strength and excellent hole expansion performance. In this study, the effects of coiling temperature on mechanical properties and hole expansion performance of low carbon Nb–Ti micro-alloyed FB590 ferrite-bainite steel have been studied. Additionally, the microstructure evolution and carbide precipitation behavior during hot rolling and coiling processes have been investigated. The influence mechanism of microstructures and carbides on both mechanical properties and hole expansion performance has also been discussed. The results suggest that the fraction of the retained austenite and the martensite decreases gradually with increasing coiling temperatures from 450 °C to 500 °C. The main reason for the formation of martensite and retained austenite in steel CT450 coiled at 450 °C is that the coiling temperature is near the martensitic transformation temperature Ms. Increasing the coiling temperature to 500 °C which is above the Ms leads to ferritic and bainitic structure. The carbides precipitation behavior has been studied by TEM, thermodynamic and kinetics calculation. The results show that the size of the carbides increases with increasing coiling temperatures from 450 °C to 500 °C. Most of the large size carbides above 100 nm with high percent of Ti are the undissolved particles in austenite during slab heating. The medium size particles between 50 nm and 100 nm and enriched in Ti precipitate during rough rolling at higher temperature, while the particles smaller than 50 nm enriched in Nb precipitate during finish rolling and coiling processes. The strength of the steel is effectively increased by the fine carbides and martensite formed at low coiling temperature of 450 °C. With increasing coiling temperature from 450 °C to 500 °C, the steel's strength decreases from 630 MPa to 591 MPa, while the HER are improved from 76.8 % to 119.9 % due to the reduction of martensite and retained austenite. Although the strength is a little reduced due to the coarsening of carbides and reducing of the martensite, the plasticity and hole expansion performance is improved significantly with the coiling temperature of 500 °C.

Biosynthesis and characterizations of silver nanoparticles by using green banana peel extract: Evaluation of their antibacterial and electrical performances

Biosynthesized silver nanoparticles (Ag NPs) hold tremendous promise in nano-bioscience, with applications spanning engineering, science, and industry. This study delves into their fabrication process, crystallographic characteristics, and nanostructures. Employing green banana peel extract (GBPE), Ag NPs were synthesized. Various analytical techniques, such as UV–Vis absorption spectrophotometry (UV), X-ray diffraction (XRD), Gas chromatography-mass spectrometry (GC-MS), Field emission scanning electron microscopy (FESEM), Fourier-transform infrared spectroscopy (FTIR), and Transmission electron microscopy (TEM) elucidate their attributes. UV–visible analysis reveals a 413 nm absorption band due to surface plasmon resonance. The Ag NPs exhibit a face-centered cubic structure with an average crystallite size of 45.87 nm. Lattice parameters and dislocation density are also determined. When tested against harmful bacteria, such as E. coli and S. epidermidis, advanced microscopy reveals a median size of particles of 55.12 nm and demonstrates their antibacterial characteristics. These environmentally benign Ag NPs also improve the efficiency of bio-electrochemical cells (BECs), opening the door to large-scale manufacturing at a reasonable cost and broadening the range of possible uses.

Effect of Ball Milling Conditions on the Microstructure and Dehydrogenation Behavior of TiH2 Powder

This study investigated the effects of revolution speed and ball size in planetary milling on the microstructure and dehydrogenation behavior of TiH2 powder. The particle size analysis showed that the large particles present in the raw powder were effectively refined as the revolution speed increased, and when milled at 500 rpm, the median particle size was 1.47 m. Milling with a mixture of balls of two or three sizes was more effective in refining the raw powder than milling with balls of a single size. A mixture of 3-mm and 5-mm-diameter balls was the optimal condition for particle refinement, and the measured median particle size was 0.71 m. The dependence of particle size on revolution speed and ball size was explained by changes in input energy and the number of contact points of the balls. In the milled powder, the endothermic peak measured using differential thermal analysis was observed at a relatively low temperature. This finding was interpreted as the activation of a dehydrogenation reaction, mainly due to the increase in the specific surface area and the concentration of lattice defects.

Predictive computational models for assessing the impact of co-milling on drug dissolution

Co-milling is an effective technique for improving dissolution rate limited absorption characteristics of poorly water-soluble drugs. However, there is a scarcity of models available to forecast the magnitude of dissolution rate improvement caused by co-milling. Therefore, this study endeavoured to quantitatively predict the increase in dissolution by co-milling based on drug properties. Using a biorelevant dissolution setup, a series of 29 structurally diverse and crystalline drugs were screened in co-milled and physically blended mixtures with Polyvinylpyrrolidone K25. Co-Milling Dissolution Ratios after 15 min (COMDR15 min) and 60 min (COMDR60 min) drug release were predicted by variable selection in the framework of a partial least squares (PLS) regression. The model forecasts the COMDR15 min (R2 = 0.82 and Q2 = 0.77) and COMDR60 min (R2 = 0.87 and Q2 = 0.84) with small differences in root mean square errors of training and test sets by selecting four drug properties. Based on three of these selected variables, applicable multiple linear regression equations were developed with a high predictive power of R2 = 0.83 (COMDR15 min) and R2 = 0.84 (COMDR60 min). The most influential predictor variable was the median drug particle size before milling, followed by the calculated drug logD6.5 value, the calculated molecular descriptor Kappa 3 and the apparent solubility of drugs after 24 h dissolution. The study demonstrates the feasibility of forecasting the dissolution rate improvements of poorly water-solube drugs through co-milling. These models can be applied as computational tools to guide formulation in early stage development.

Replacing Fly Ash or Silica Fume with Tuff Powder for Concrete Engineering in Plateau Areas: Hydration Mechanism and Feasibility Study

Abundant tuff mineral resources offer a promising solution to the shortage of fly ash (FA) and silica fume (SF) resources as emerging supplementary cementitious materials. However, a lack of clarity on its hydration mechanism has hindered its practical engineering application. In this study, high SiO2-content tuff powder (TP) was examined to assess the mechanical and workability performance of mortar specimens with varying particle sizes of the TP as complete replacements for FA or SF. Microscopic analysis techniques, including X-ray diffraction (XRD), differential thermal analysis (DTG), and energy-dispersive X-ray spectroscopy (EDS), were employed to elucidate the hydration mechanism of the TP and its feasibility as a substitute for SF or FA. Results indicated that TP primarily functions as nuclei and filler, promoting cement hydration, with smaller particle sizes amplifying the hydration ability and increasing Ca(OH)2 and C-S-H gel content. The specimens with TP (median particle size 7.58 μm) demonstrated 9.2% and 29.9% higher flexural and compressive strengths at 28 days, respectively, compared to the FA specimens of equal mass. However, fluidity decreased by 23.1% accordingly. Due to TP’s smaller specific surface area compared to SF, the TP specimens exhibited higher fluidity but with decreased strength relative to the SF specimens. Overall, TP shows potential as a replacement for FA with additional measures to ensure workability.

Synthesis, investigation of temperature and salt resistant polyacrylamide microspheres used for deep sealing and profile control and function strengthening mechanism

AbstractBased on the requirements of deep sealing and profile control for the excellent temperature and salt resistance on polyacrylamide microspheres, the Poly‐AM/AMPS was prepared depends on aqueous solution polymerization method to improving oil and gas recovery efficiency in low‐permeability and heterogeneous reservoirs resulted by water channeling. The key technical parameters were established through single‐factor experimental methods, and the chemical structure was studied by infrared spectrum analysis (FTIR), energy spectrum analysis, and x‐ray diffraction analysis, and then the thermal stability was investigated depends on the thermogravimetric (TG) and differential thermogravimetric (DTG) distribution curves, moreover, the particle size and distribution, microstructure, and surface morphology were further studied. As a result, the results confirmed that the molecular structure of Poly‐AM/AMPS meets the expected design, and the quality retention rate at 800°C is 17.4%, the median particle size of Poly‐AM/AMPS particles is 35.88 μm, and the particle size distribution range is about 1.94–497.8 μm. Further, the Poly‐AM/AMPS was modified by maleic anhydride, sodium styrenesulfonate, and dimethyl diallyl ammonium chloride through conventional functional strengthening and modification, modified by nano‐SiO2, GO, and S‐CaCO3 through nano‐functional strengthening and modification. Additionally, the functional strengthening and modification mechanism was studied depends on the FTIR, TG, and DTG methods.

Copper heap leach residue aggregates in concrete: Properties and performance

This study assesses the feasibility of using copper heap leach residue (CHLR) as a sustainable alternative to natural aggregates in concrete production. The CHLR possesses flaky-angular shape grains with rough surface texture and microcracks, crystalline silica of 51.6 %, 6.1 mg/g silt-clay with a median particle size of 4.3 mm, and it becomes suitable for the partial replacement of natural fine and coarse aggregates after removing 4.2 mg/g fines through 60-minute wash. Concrete containing 25–75 % CHLR aggregates met design slump and air content of 125±25 mm and 2±0.5 %, respectively, while also demonstrating a negligible 2.9 % reduction in fresh density and 2.8 % increase in compaction factor. Concrete containing 50 % CHLR as a partial replacement of natural coarse and fine aggregates achieved compressive strengths of 47.3 MPa and 45.1 MPa at 28 days, while the compressive strength of control mix was 46.7 MPa. The mechanical properties significantly declined at 75 % CHLR incorporated concretes. The BSE-EDS analysis highlighted improved interfacial transition zone for CHLR aggregates with minimal microcracks at early age compared to the natural aggregates but developed interfacial transition zone microcracks with prolonged curing leading to a decline in mechanical strength development.

Multi-Parameter Experimental Research on the Expansion Force Affecting Lime-Sand Piles under Preloading Pressure

Aiming at the problems that it is difficult to control the expansion force of lime-sand pile in the foundation correcting and how the upper existing structural pressure affects the expansion force of lime-sand pile, this paper adopts a new type of lime-sand pile reaction tester to carry out the experimental research on the expansion force of lime-sand pile under the influences of different pre-pressure, different mixing ratios, different heights, and different granular sizes. The purpose of this paper is to explore the influence of the pre-pressure brought by the existing building structure on the expansion force of the lime-sand pile and the coupling effect of the pre-pressure and other influencing factors on the expansion force of the lime-sand pile through the multi-parameter test. The results show that with the increase in pre-pressure, the expansion force of the lime-sand pile shows the trend of increasing first and then decreasing when the pre-pressure is 0.88 KN, the effect is most obvious and its expansion force can be increased by 14.9%. Within a certain range, the larger the proportion of quicklime is, the lower the expansion reaction force is. The expansion force of the lime-sand pile with the ratio of lime/sand/soil of 5:4:1 is the most ideal, and its value reaches 10.2 KN, which is 10% and 15.3% higher than the rest of the two groups, respectively. Within a certain range, the effect of specimen height change on the expansion force of the lime-sand pile is almost negligible. The smaller particle size of quicklime makes its reaction speed faster, the reaction degree is more full, and the expansion force is greater. The expansion force of the small particle size group was 12.1% and 34.2% higher than that of the medium and large particle size groups, respectively.

Effect of milling and compaction on sintering of porcelain stoneware tiles

The present study aims to provide a deeper understanding of how different particle size distributions and degrees of powder compaction affect the densification process of porcelain stoneware tiles. For this purpose, three different batches underwent a laboratory simulation of the industrial tilemaking process, at growing grinding time or increasing forming pressure, with technological characterization of both unfired and fired products. Sintering behaviour was determined by hot-stage microscopy. Phase composition was determined by XRD-Rietveld allowing the estimation of the chemical composition and physical properties of the liquid phase. The results illustrate the impact of too fine (or too coarse) grain size on powder compaction, firing shrinkage, water absorption, efficiency of densification, sintering rate, stability at high temperature, and risk of anticipated overfiring (and similarly for too high or too low forming pressure). Simultaneous variation of particle size and forming pressure beyond usual standards induced changes in technological behaviour that in most cases compensate each other. Phase composition is moderately influenced by particle size and little by powder compaction. The vitreous phase mainly suffered from a decreasing degree of polymerization as the particle size became finer or the dry bulk density decreased. In case of insufficient grinding, too much residual feldspars caused improper composition and properties of the glassy phase, which resulted in lower efficiency of densification and slower sintering rate. Both the sintering kinetics and degree of densification depend on the timescale, i.e. the ratio of surface tension to viscosity (melt) and median particle size. Nevertheless, a low powder compaction can trigger a microstructural effect on sintering (improving both densification rate and efficiency) that may outweigh the timescale effect.

Improvement of the mechanical properties of beta-hemihydrate phosphogypsum by incorporating wet-ground low-calcium fly ash slurries

Beta-hemihydrate phosphogypsum (β-HPG) is a low-carbon cementitious material used in construction. Nevertheless, the poor water resistance and low mechanical strength of β-HPG limit its utilization. In this study, two low-calcium fly ash (FA) slurries with median particle sizes of 1.83 μm and 1.14 μm were prepared using a wet-grinding process for the improvement of β-HPG, and the mechanical strength and softening coefficient were tested to assess the effect. The results show that wet-ground low-calcium FA can significantly enhance the mechanical strength and softening coefficient of β-HPG. Compared with specimens without wet-ground low-calcium FA, the dry compressive strength and softening coefficient of specimens with 30% wet-ground low-calcium FA (D50=1.14 μm) increased by 104.9% and 71.8%, respectively. It is worth noting that the 1 d compressive strength also increased by 11.9%. Specifically, wet-ground low-calcium can increase the pH value and conductivity of the FA slurry, further accelerate the hydration process of FA in β-HPG, forming more ettringite and gels to fill in the pores between dihydrate gypsum (DH) crystal, and reducing the larger pores in the hardened paste. This study can develop a high-performance cementitious material that will enable the effective use of β-HPG.

Effect of wet milling activation on mechanical properties and hydration process of cement composites with blast furnace slag

In this study, blast furnace slag (BFS) was activated using water- and ethanol-assisted milling (AM). BFS-cement composites (BFS-CC) were prepared using milled BFS and cement. The effects of the activation process on the mechanical properties and hydration of BFS-CC were investigated. Results showed that water- and ethanol-AM significantly reduced the median particle size (D50) and improved the particle size distribution of BFS compared to dry milling. Water-AM increased the compressive strength of BFS-CC at 3 days by 19.9 % and decreased the compressive strength at 28 days by 6.7 %. While ethanol-AM increased the compressive strengths at 3 and 28 days by 17.2 and 22.4 %, respectively. Water-AM improved the early strength of BFS-CC, whereas ethanol-AM contributed significantly to the late strength development of BFS-CC. This study provides an effective and convenient method for regulating the mechanical properties of cement composites containing high-volume BFS.

Investigation on the Micro-Grinding Induced Crystallographic Variations of Nine Different Clinkers

Although clinker has been used for many years, complicated mineralogical properties of clinker pose challenges for the precise quantification. In this study, the mineralogical and crystallographic properties of nine different clinkers according to grinding procedures were investigated. With the dry-grinding for 2 h, particle size reduction to 3 μm of median particle size with a substantial phase transition to an amorphous phase observed, to which alite (C3S) mainly contributed to the transition. Meanwhile, the crystallographic properties of the clinker phases were barely changed during the wet-grinding. In the wet-grinding program, the amount of ferrite solid solution (C4AF) with a high linear absorption coefficient was not underestimated. Furthermore, well-corrected preferred orientation effect on C3S was positively contributed to the analysis result of clinkers with the wet-grinding. Hence, it was suggested that the crystallographic effects observed in the wet-grinding program could produce more reliable results in phase analysis for the clinkers.

The Influence of Freezing-thawing on the Properties of Sludge from Water Treatment Facilities and the Prospects for its Disposal

It has been shown that the freezing-thawing method allows a sharp increase in the water-yielding capacity of water treatment sludge (WTS sludge) and leads to an increase in the median particle size of the dispersed phase of sludge. The distribution of bound water types in WTP sludge was studied using thermogravimetry (TG), differential thermal thermogravimetry (DTG), differential scanning calorimetry (DSC) and mass spectrometry of gaseous thermolysis products (MS). It has been established that the release of water and carbon dioxide is completely completed at a temperature of 600°C. The specific surface area of the solid phase of WTP sludge before and after freezing-thawing was determined. The pore size distribution was studied. The BET isotherm of WTP sludge corresponds to mesoporous sorbents.

Production of recycled paper using harmless municipal sludge as a new biomass filler

Abstract Due to a shortage of resources, exploring new biomass fillers has become critical for paper making. In this study, we reported an eco-friendly strategy for fabricating low-cost and efficient recycled paper with high mechanical properties using corrugated cardboard waste paper and harmless municipal sludge (HMS). First, the characteristics of HMS, including the particle size, pH, specific surface area, organic functional groups and organic component content, were analyzed. Then, the influence of the amount of HMS on the properties of the recycled paper was studied. Finally, the strengthening mechanism of biomass filling recycled paper was discussed. The results showed that HMS, a biomass filler for recycled paper preparation, exhibited excellent physical and chemical properties, with a median particle size of 6.395 μm, a surface area of 39.974 m2 g−1 and organic functional groups. The tensile index of the recycled paper with 30 % HMS was 13.10 Nm/g, which was 16.4 % greater than that of the unfilled paper and showed better thermal stability. This excellent performance could be attributed to the uniform distribution of HMS on the fiber surface, which improved the accessibility of hydrogen bond formation between fibers. Thus, this study proved that HMS was an excellent biomass filler for producing recycled paper.