Main Polymer Research Articles

Pollution characteristics and release mechanism of microplastics in a typical end-of-life vehicle (ELV) recycling base, East China

Microplastics (MPs) is a novel and significant pollution due to its eco-environmental hazards and ubiquity. In end-of-life vehicle (ELV) recycling base, MPs are widely distributed but have rare reported in scientific literature. In this study, a comprehensive analysis of MPs was conducted in a typical ELV recycling base. MPs were found in all samples at different sampling sites and environmental mediums. A total of 34 polymer types were detected by μ-FTIR, and the main polymers include PE-PP, ABS, polyester resin, nylon, and PEU plastic. MPs were released from the crushing, tearing, and breaking of plastic parts in ELVs. They were in high content in ground dust, with the abundance of 737–29,021 p/5 g D (the average abundance of 5552 ± 6435 p/5 g D). The abundance, shape, color, and size of MPs are related with functional areas of ELV recycling. Heavy metals could be adsorbed on MPs, and their contents on MPs have a significant correlation with those in the corresponding dust samples. At last, some specific MPs control measures, such as changing transportation mode, using dust-proof cloths, and equipping dust removal equipment, have been put forward.

Microfiber pollution from Dhobi Ghats (open air laundry centers) and commercial laundries in a north Indian city.

In regions like Southeast Asia, Dhobi Ghats-traditional open-air laundromats-hold cultural significance and provide livelihoods to many people. These centers are near the riverbanks for easy access to water for washing. These Dhobi Ghats are among major sources of microfibers (MFs) in the waterbodies. However, there is no ample data that confirms their level of MF release into the waterbodies. This study reports for the first time the prevalence of microfibers (MFs) in wastewater from Dhobi Ghats in a North Indian city and comparatively assess them with the MF pollution from commercial laundries. A mean microfiber concentration of 3204 ± 270 MFs/L was observed in the discharged effluents of Dhobi Ghats, while a concentration at 36,923 ± 389 MFs/L was observed in effluents from commercial laundries. Pertinently, microfibers measuring less than 75µm dominated in effluents of commercial laundries, accounting for 53% of the total. Conversely, microfibers within the 75-150-µm range were present in effluents of Dhobi Ghats, constituting 52%. Spectroscopic analyses by FTIR showed polyester and polyamides as the main polymers released from Dhobi Ghats. Ecological risk assessment demonstrated a potential environmental risk from the MF pollution from Dhobi Ghats and commercial laundries. The study also proposed a mitigation framework prioritizing both environmental protection and the sustenance of local livelihoods for reducing the microfiber pollution by the Dhobi Ghats.

Robust superhydrophobic coating with carbon nanotubes and silica nanoparticles in the matrix of fluorinated polyurethane

After years of research, superhydrophobic coatings have made great progress, but the complex preparation process and poor durability are still key issues that limit their practical application. Herein, we developed a room temperature cured durable superhydrophobic coating through a simple spraying method. The main polymer matrix used in this study was fluorinated polyurethane (FPU), which exhibited high hardness (5H), strong adhesion to the substrate (grade 1, GB/T 9286), and excellent hydrophobicity with a contact angle of approx. 108 ° Silica nanoparticles were found to be highly effective in enhancing the surface hydrophobicity of FPU. Nevertheless, these particles can be easily removed from the surface by even a simple touch with a finger. For enhanced durability, we incorporated carbon nanotubes (CNTs) with intertwining structures. Additionally, polydimethylsiloxane (PDMS) was utilized to facilitate the interaction between the inorganic fillers and the organic FPU matrix, owing to its inorganic Si-O skeleton and organic side chains. The so-optimised composite coating was covered with micro-/nano- particles and the hydrophobicity was enhanced greatly (contact angle of ∼165 ° and sliding angle of 5.5 °). The contact angle of the coating remained higher than 150 ° even after undergoing a range of tests. These tests included immersing in corrosive solutions for 60 h, gravel impacting for 100 cycles, water jetting for 1200 s, and abrading against sandpaper for 1000 cycles. The good chemical and mechanical durability was due to the high compactness, high hardness (4H pencil hardness), and high adherence (grade 1, GB/T 9286) of the coating. Moreover, due to the photothermal conversion effect of carbon nanotubes, the coating possessed excellent photothermal performance and showed good application prospects in anti icing / deicing.

Assessment of meso- and microplastics distribution in coastal sediments and waters at the middle estuary of the Rio De La Plata, Argentina (SW Atlantic Ocean)

Estuarine coastal water and sediments collected from multiple locations within the middle Río de la Plata (RDLP) estuary were analyzed in order to identify the presence of microplastics (MPs, <5 mm) and mesoplastics (MePs, 5–25 mm) in one of the most significant estuaries in the Southwestern Atlantic. The present study represents one of the first researches to survey MPs and MePs contamination in key stations at RDLP estuary. Average concentrations of 14.17 ± 5.50 MPs/L and 10.00 MePs/L were detected in water samples, while 547.83 ± 620.06 MPs/kg (dry weight) and 74.23 ± 47.29 MePs/kg d.w. were recorded in sediments. The greatest abundances were observed in the more anthropized areas, near urban settlements. Fibers were the most conspicuous plastic items in water and sediments, followed by fragments. On the other hand, surface sediments, and 50 cm and 100 cm-depth sediments also presented MPs and MePs indicating they could serve as a stratigraphic indicator for recently formed sediments. The main polymer type identified were acrylic fibers, followed by polypropylene (PP) and polyethylene terephthalate (PET). Besides, SEM-EDX detected the presence of Si, Fe, Ti, Al and Cl onto the plastics' surface. These elements may serve as additives to enhance the plastics' properties, such as in the case of Ti, or they could originate from the environment, like biogenic Si or Fe, and Al possibly as a component of the suspended particles or sediments adhered to the micro or meso plastics. Finally, the results of the present study showed that MPs and MePs are commonly found in waters and also tend to be trapped in sediments of the RDLP estuary supporting the assertion that these areas play a substantial role in influencing the transport, dispersion, and buildup of MPs in estuarine regions.

Main chain selective polymer degradation: controlled by the wavelength and assembly.

The advent of reversible deactivation radical polymerization (RDRP) revolutionized polymer chemistry and paved the way for accessing synthetic polymers with controlled sequences based on vinylic monomers. An inherent limitation of vinylic polymers stems from their all-carbon backbone, which limits both function and degradability. Herein, we report a synthetic strategy utilizing radical ring-opening polymerization (rROP) of complementary photoreactive cyclic monomers in combination with RDRP to embed photoresponsive functionality into desired blocks of polyvinyl polymers. Exploiting different absorbances of photoreactive cyclic monomers, it becomes possible to degrade blocks selectively by irradiation with either UVB or UVA light. Translating such primary structures of polymer sequences into higher order assemblies, the hydrophobicity of the photodegradable monomers allowed for the formation of micelles in water. Upon exposure to light, the nondegradable blocks detached yielding a significant reduction in the micelle hydrodynamic diameter. As a result of the self-assembled micellar environment, telechelic oligomers with photoreactive termini (e.g., coumarin or styrylpyrene) resulting from the photodegradation of polymers in water underwent intermolecular photocycloaddition to photopolymerize, which usually only occurs efficiently at longer wavelengths and a much higher concentration of photoresponsive groups. The reported main chain polymer degradation is thus controlled by the irradiation wavelength and the assembly of the polymers.

Frustrated Lewis pair adducts of alkynyl-capped tetrelenes.

The frustrated Lewis pair (FLP) adducts PB{ECl2} (PB = iPr2P(C6H4)BCy2; Cy = cyclohexyl; E = Si, Ge) were used to access a bis(alkynyl)-functionalized silylene and a germylene; the goal behind preparing these species was to obtain new unsaturated main group polymers [E(CCSiMe3)2]n upon heating. While the silylene adduct PB{Si(CCSiMe3)2} was stable up to 150 °C, the heavier element congener PB{Ge(CCSiMe3)2} underwent a complicated rearrangement process accompanied by Cy-group migration and Ge(II)-alkyne coordination. Density functional theory computations were performed to understand the mechanistic pathway for the unusual rearrangement of PB{Ge(CCSiMe3)2}.

Development of a light-responsive fluorinated poly(arylene ether) copolymer containing azobenzene groups in the main polymer chain

A novel azo-based polymer with high mechanical and thermal stability is obtained. The polymer exhibits stable birefringence changes, enabling the fabrication of diffraction gratings, showing its potential for various optical applications.

In Ukrainian

Thermal destruction of composites of ureaformaldehyde (UPR) and polyester resins (PER) with silicon dioxide nanoparticles having a specific surface area of 280 m2/g, titanium dioxide and titanosilicate with a specific surface area of 40 and 48 m2/g, respectively, when a filler content is no more than 5.0 wt% have been studied. The investigations were performed using The thermally programmed mass spectrometry method with registration of the masses of desorbed atomic fragments in the 10 ‒ 200 m/z range. It was established that during the main polymer mass destruction at 150 ‒ 350 oC, along with low temperature decomposition products, anomalously high thermal resistance of a number of atomic fragments of polymer chains and cross-links are recorded. The atomic composition of destruction fragments and their desorption temperature in the range 400 ‒ 700 oС were determined. It was established that in composites of ureaformaldehyde resin with SiO2 and TiO2 nanoparticles the high temperature resistance of fragments with m/z 27 exhibits due to the formation of strong bonds among the Si and Ti surface sites and the nitrogen atoms of the polymer. Such thermal stability is not realized in resin loading with (Si/Ti)O2 nanoparticles. In composites of polyester resin with silica a high-temperature destruction of oxygen atoms from polyester chains realizes at temperatures of 290 ‒ 400 oC and a low-intensity wide destruction band takes place in the temperature range 400 ‒ 700 oC. In addition, in the temperature range of 400-700 oC cross-links are destroyed with the release of benzene rings and styrene molecules. It was established that anomalously high-temperature desorption is typical for atomic fragments of the polymer structure attached to surface Si and Ti sites through nitrogen or carbon atoms from the polymer structure. Thus, in UPR composites with silicon and titanium oxides, strong chemical nitride bonds of the form Si-N≡C-H and Ti-N≡C-H are formed, which demonstrate anomalously high heat resistance. It is shown that in composites of polyester resin with silicon dioxide nanoparticles, the high-temperature destruction of fragments is due to their desorption from the surface of silicon dioxide particles when breaking their bonds with silicon atoms. Thus, polymer matrices have been determined, in which atomic fragments of the macromolecule, binding to the surface centers of fillers, significantly weaken the thermal destruction of composites due to the formation of strong chemical and coordination bonds.

Exploring the microplastic pollution: Unveiling origins and varieties in coastal sediments and waters of the Bushehr Province, Persian Gulf, Iran

In this study, microplastic (MP) pollution in the coastal sediments and tidal waters of Bushehr province in the Persian Gulf was comprehensively investigated. The sampling stations were selected based on their proximity to various human activities in January and February 2022, such as tourism, fishing, urban development and industry. The results showed that the abundance of MP associated with different human activities varied. The highest concentrations were observed near the petrochemical industry in Asaluyeh, followed by the densely populated Bushehr and the fishing port of Dayyer. Other areas such as Ganaveh, Deylam and Mand also showed varying levels of MP contamination. The average MP concentration was 1.67 × 104 particles/km2 in surface water and 1346.67 ± 601.69 particles/kg in dry sediment. Fiber particles were in the majority in both sediment and water samples, mainly black. The sediment samples had a size range of 100–500 μm (41.34 %), while the water samples were between 500 and 1000 μm (33.44 %). The main polymers found were polyethylene (PE) and polypropylene (PP). This assessment highlights the widespread problem of microplastic pollution in the coastal and intertidal zones of Bushehr province in the Persian Gulf.

Assessing microplastics contamination in unviable loggerhead sea turtle eggs

Sea turtles, in comparison with marine mammals, sea birds, and fishes, are the most affected by microplastics in terms of number of individuals impacted and concentration within each organism. The ubiquitous nature and persistence of microplastics in the environment further compromises sea turtles as many species are currently vulnerable, endangered, or critically endangered. The objective of this study was to quantify microplastic contamination in unviable loggerhead sea turtle eggs (Caretta caretta). Eggs were collected from seven locations along the northwest coast of Florida. A total of 70 nests and 350 eggs were examined. Microplastics (n = 510) were found in undeveloped loggerhead sea turtle eggs across all seven sites, suggesting that maternal transference and/or exchange between the internal and external environment were possible. The frequency found was 7.29 ± 1.83 microplastic pieces per nest and 1.46 ± 0.01 per egg. Microplastics were categorized based on color, shape, size, and type of polymer. The predominant color of microplastics were blue/green (n = 236), shape was fibers (n = 369), and length was 10–300 μm (n = 191). Identified fragments, films, beads and one foam (n = 187) had the most common area of 1–10 μm2 (n = 45). Micro-Fourier Transform Infrared (μ-FTIR) spectroscopy analysis demonstrated that polyethylene (11 %) and polystyrene (7 %) were the main polymer types. For the first time microplastics were found in unviable, undeveloped loggerhead sea turtle eggs collected in northwest Florida. This work provides insight into the distribution patterns of microplastic pollutants in loggerhead sea turtle eggs and may extend to other species worldwide.

Gel Polymer Electrolytes for Lithium-Ion Batteries Enabled by Photo Crosslinked Polymer Network.

We demonstrate a gel polymer electrolyte (GPE) featuring a crosslinked polymer matrix formed by poly(ethylene glycol) diacrylate (PEGDA) and dipentaerythritol hexaacrylate (DPHA) using the radical photo initiator via ultraviolet (UV) photopolymerization for lithium-ion batteries. The two monomers with acrylate functional groups undergo chemical crosslinking, resulting in a three-dimensional structure capable of absorbing liquid electrolytes to form a gel. The GPE system was strategically designed by varying the ratios between the main polymer backbone (PEGDA) and the crosslinker (DPHA) to achieve an optimal gel polymer electrolyte network. The resulting GPE exhibited enhanced thermal stability compared to conventional liquid electrolytes (LE) and demonstrated high ionic conductivity (1.40 mS/cm) with a high lithium transference number of 0.65. Moreover, the obtained GPE displayed exceptional cycle performance, maintaining a higher capacity retention (85.2%) comparable to the cell with LE (79.3%) after 200 cycles.

Gellan gum-based bi-polymeric hydrogel scaffolds loaded with Rosuvastatin calcium: A useful tool for tendon tissue regeneration

Statins have been long used in tissue engineering, besides their marketed hypolipidemic benefits. The aim of this research was to sustain the release of rosuvastatin calcium from bi-polymeric hydrogel scaffolds. A bi-polymer blend technique was used to enhance the mechanical properties of the fabricated hydrogels. Briefly, hydrogels were prepared via crosslinking gellan gum as the main polymer together with a secondary polymer in the presence of Ca2+. The fabricated hydrogels were assessed in terms of % swelling capacity, hydrolytic degradation and % drug released to determine the most efficient carrier system. The selected hydrogel exhibited a swelling capacity of 131.45±1.49 % following 3 weeks in an aqueous environment with a % weight loss of 15.73±1.86 % after 4 weeks post-equilibrium in aqueous medium. The results ensure a proper window for adequate drug diffusion and nutrient exchange. Sustained release was attained where 94.61±2.77 % of rosuvastatin was released at the 4-week mark. Later, FT-IR and DSC, were carried out and suggested the successful crosslinking and formation of new matrix. SEM images demonstrated the porous surface of the hydrogel while a Young's modulus of 888.558±73.549 kPa indicated the suitability of the hydrogel for soft tissue engineering. In-vivo testing involved implanting the selected hydrogel at precisely surgical cuts in the Achilles tendon of male Wistar Albino rats. Upon visual and microscopic evaluation, enhanced rates of fibrous tissue formation, vascularization and collagen expression were clearly noticed in the treatment group.

Formulation and evaluation of buccal film of an antihypertensive drug

The aim of the study was to formulate and evaluate Losartan potassium buccal films, an angiotensin receptor blocker and is used to treat hypertension. Losartan potassium is having less bioavailability (33%), so the buccal films are expected to increase the bioavailability by avoiding hepatic metabolism. Ten formulations of buccal films were prepared by solvent casting method using HPMC K15 M as the main film-forming polymer in various proportions with various co-polymers such as Eudragit RL. 100, Carbopol 940, Ethyl cellulose. Physicochemical characteristics,in vitro buccal permeation, in vitro release study and residence time were evaluated. In vitro studies revealed that the release rate of Losartan potassium was higher for films containing HPMC K15 M and Eudragit RL100 in 3:1 ratio. The result of stability study indicated that no significant changes have occurredduring the period of study.

Development and Evaluation of Transdermal Gel for Pain Relief

The study was to develop transdermal gel formulations for the delivery of aspirin and paracetamol. Compared to more conventional approaches like oral, injectable, and inhaler administration, transdermal medication delivery through the skin has a number of benefits. These benefits include self-administering simplicity, non-intrusiveness, usability, cost, and the capacity to maintain sustained plasma drug concentrations over prolonged periods of time. Two polymers in creating transdermal gels Carbopol-934 and Sodium Alginate were assessed. Carbopol-934 was chosen because of its capacity to improve drug retention and limit drainage, allowing for the drug's sustained release. The gel compositions were thickened and stabilized using sodium alginate. Pre-formulation tests, rheological characteristics, spread-ability, pH levels, homogeneity, and potential for skin irritation were assessed for both Carbopol-934 and Sodium Alginate gel formulations. In order to avoid application-related skin irritation, the pH levels of the gel formulations were closely checked to make sure they stayed within the permitted range. In comparison to other Carbopol-934 and Sodium Alginate formulations tested, Carbopol-934 gel formulation F3 showed the best spread-ability (S=95.9). Due to its constant qualities, including acceptable spread-ability, pH range, and homogeneity, without producing any skin irritation, this formulation was deemed satisfactory. In conclusion, the creation of a transdermal gel formulation using Carbopol-934 as the main polymer matrix shows potential for delivering these medications through the skin. This study highlights the potential of transdermal drug delivery devices as a practical and efficient replacement for conventional methods of administering painkillers.

Membrane Contamination Control in the Intermittent Aeration Mode of Operation of the C-MBR Process for Campus Wastewater Reuse

Filtration backwashing is necessary for the effective operation of membrane modules, and intermittent aeration helps to remove nutrients, which can save energy and effectively control the occurrence of membrane contamination. In this study, membrane contamination was controlled using an MBR in intermittent aeration operation mode and a filtration backwash cycle; difficult organic matter and nitrogen (COD and NH4+-N) were used as the main contamination indicators for this study; and the main membrane contamination components, extracellular polymers (EPs), and soluble microbial products (SMPs) were detected. The results show that the average removal of COD and NH4+-N could reach 86.45% and 92.47%, respectively, with a 2.0 day intermittent aeration time and 9/1 min filtration backwash cycle mode, and it also helped to reduce the membrane contamination, as shown by a decrease of 11.87% in bound EPs (EPSBound) and an increase of only 5.32% in SMPs. Microbiological analyses revealed that Proteobacteria and Acinetobacter, as dominant bacteria (50.90%), were the main causes of membrane contamination.

Quantification and characterization of microplastics in farmland soils of Jiangsu Province, East China.

The soil ecosystem plays a significant role in the dynamics of microplastics. Qualitative and quantitative analyses of microplastics in six farmland plots from the cities of Nanjing, Suzhou, and Xuzhou were conducted by using laser infrared imaging system (LDIR). The results showed that the abundance of microplastics in farmland soils in Jiangsu Province ranged from 667-9333 items/kg, and the difference between the abundance of microplastics in soils from open-field cultivation and greenhouse farming was not significant. The vertical distribution characteristics showed that the abundance of microplastic decreased significantly with the increase of soil depth. However, there was no significant difference in particle size between top soil (0-5cm) and deep soil (10-20cm). Fragments were the most common microplastic form in soil samples (94.6%), with polyvinyl chloride (PVC) being the main polymer type, followed by polyethylene terephthalate (PET). Compared with previous studies conducted in China, the abundance of microplastics in farmland soils in Jiangsu Province was at moderate level but was notably higher than other places within the Yangtze River Delta region. The conclusions drawn from this paper provided important reference data for future assessment of microplastic pollution in agricultural fields. Furthermore, they establish a fundamental groundwork for understanding the migration patterns of MPs in soil environments.

Biochemical and structural characterization of a glucan synthase GFGLS2 from edible fungus Grifola frondosa to synthesize β-1, 3-glucan

BackgroundGrifola frondosa is a Basidiomycete fungus belonging to the family of Grifolaceae and the order of Polyporales. β-Glucans are the main polymers in G. frondosa, playing a crucial role in the physiology and representing the healthy benefits for humans. The membrane-integrated β-1, 3-glucan synthase (GLS) is responsible for glucan synthesis, cell wall assembly, differentiation and growth of the edible fungi. However, the structural/catalytic characteristics and mechanisms of β-1, 3-glucan synthases in G. frondosa are still unknown due to their extremely complex structures with multi-transmembranes and large molecular masses.ResultsHerein, a β-1, 3-glucan synthase (GFGLS2) was purified and identified from the cultured mycelia with a specific activity of 60.01 pmol min−1 μg−1 for the first time. The GFGLS2 showed a strict specificity to UDP-glucose with a Vmax value of 1.29 ± 0.04 µM min−1 at pH 7.0 and synthesized β-1, 3-glucan with a maximum degree of polymerization (DP) of 62. Sequence Similarity Network (SSN) analysis revealed that GFGLS2 has a close relationship with others in Ganoderma sinense, Trametes coccinea, Polyporus brumalis, and Trametes pubescens. With the assistance of 3D structure modelling by AlphaFold 2, molecular docking and molecular dynamics simulations, the central hydrophilic domain (Class III) in GFGLS2 was the main active sites through binding the substrate UDP–glucose to 11 amino acid residues via hydrogen bonds, π-stacking and salt bridges.ConclusionsThe biochemical, 3D structural characterization and potential catalytic mechanism of a membrane-bound β-1, 3-glucan synthase GFGLS2 from cultured mycelia of G. frondosa were well investigated and would provide a reasonable full picture of β-1, 3-glucan synthesis in fungi.

Sustainable Polyhydroxyalkanoate Production from Food Waste via Bacillus mycoides ICRI89: Enhanced 3D Printing with Poly (Methyl Methacrylate) Blend.

In view of implementing green technologies for bioplastic turning polices, novel durable feedstock for Bacillus mycoides ICRI89 used for efficient polyhydroxybutyrate (PHB) generation is proposed herein. First, two food waste (FW) pretreatment methods were compared, where the ultrasonication approach for 7 min was effective in easing the following enzymatic action. After treatment with a mixture of cellulase/amylases, an impressive 25.3 ± 0.22 g/L of glucose was liberated per 50 g of FW. Furthermore, a notable 2.11 ± 0.06 g/L PHB and 3.56 ± 0.11 g/L cell dry eight (CDW) over 120 h were generated, representing a productivity percentage of 59.3 wt% using 25% FW hydrolysate. The blend of polyhydroxybutyrate/poly (methyl methacrylate) (PHB/PMMA = 1:2) possessed the most satisfactory mechanical properties. For the first time, PHB was chemically crosslinked with PMMA using dicumyl peroxide (DCP), where a concentration of 0.3 wt% had a considerable effect on increasing the mechanical stability of the blend. FTIR analysis confirmed the molecular interaction between PHB and PMMA showing a modest expansion of the C=O stretching vibration at 1725 cm-1. The DCP-PHB/PMMA blend had significant thermal stability and biodegradation profiles comparable to those of the main constituent polymers. More importantly, a 3-Dimetional (3D) filament was successfully extruded with a diameter of 1.75 mm, where no blockages or air bubbles were noticed via SEM. A new PHB/PMMA "key of life" 3D model has been printed with a filling percentage of 60% and a short printing time of 19.2 min. To conclude, high-performance polymeric 3D models have been fabricated to meet the pressing demands for future applications of sustainable polymers.

Estimated microplastic stress and potential affiliated toxic elements on phytoplankton in a floodplain-lake system.

Hazards associated with microplastics (MPs) and the pollutants they absorb in freshwater lake ecosystems have become a hot research topic in academia. In this study, in order to investigate potential affiliated MP hazards, lake MP samples were collected from a typical subtropical freshwater lake system in China (Poyang Lake) during the dry season (here, you should show the specific months) to explore their potential toxic element (PTE) response (i.e., exposure to Cu, Pb, and Zn) respective to the ecological environment and resident phytoplankton. Results show that average MP abundance in surface water can reach up to 1800 items m-3, which higher in the Nanjishan Wetland National Nature Reserve (NWNNR) (1175 items m-3). Polyester (i.e., purified terephthalic acid [PTA]) and polyethylene (PE) were the main polymer types found in surface water, fiber was the main MP shape, and most of the MP particle sizes are greater than 100 μm. Moreover, phytoplankton biomass was significantly higher in the NWNNR compared to Poyang Lake's retention basin and water channel. It indicated that MP pollutant status of Poyang Lake is mild; however, the ecological risks that MPs pose should not be ignored. The significant positive correlation between MPs and PTEs indicated that PTE absorption and desorption by MPs may cause potential ecological stress. Although we anticipate no direct link between ecotoxicity and phytoplankton, MPs may have indirect effects on phytoplankton through their regulatory effects on PTE levels in water.

Lysozyme Inhibitors as Tools for Lysozyme Profiling: Identification and Antibacterial Function of Lysozymes in the Hemolymph of the Blue Mussel.

Lysozymes are universal components of the innate immune system of animals that kill bacteria by hydrolyzing their main cell wall polymer, peptidoglycan. Three main families of lysozyme have been identified, designated as chicken (c)-, goose (g)- and invertebrate (i)-type. In response, bacteria have evolved specific protein inhibitors against each of the three lysozyme families. In this study, we developed a serial array of three affinity matrices functionalized with a c-, g-, and i-type inhibitors for lysozyme typing, i.e., to detect and differentiate lysozymes in fluids or extracts from animals. The tool was validated on the blue mussel (Mytilus edulis), whose genome carries multiple putative i-, g-, and c-type lysozyme genes. Hemolymph plasma of the animals was found to contain both i- and g-type, but not c-type lysozyme. Furthermore, hemolymph survival of Aeromonas hydrophila and E. coli strains lacking or overproducing the i- type or g-type lysozyme inhibitor, respectively, was analyzed to study the role of the two lysozymes in innate immunity. The results demonstrated an active role for the g-type lysozyme in the innate immunity of the blue mussel, but failed to show a contribution by the i-type lysozyme. Lysozyme profiling using inhibitor-based affinity chromatography will be a useful novel tool for studying animal innate immunity.