Interaction Of Magnetic Field Research Articles

AC transport loss analysis of HTS stack busbars for all-electric aircraft with harmonics and DC offset considerations

This paper presents a study of the current carrying capacity and AC loss of high-temperature superconducting (HTS) stacks to be used in busbar applications for all-electric aircraft. A 2D model was developed using COMSOL Multiphysics with a T-A formulation for detailed analysis. The study began by applying a stable 20 kA DC offset current to the HTS stacks to simulate practical operating conditions. Firstly, the behaviour of the critical current was studied under self-field conditions for stacks with different numbers of HTS tapes and spacing. Secondly, AC ripple currents were introduced with DC offsets, and the effects of 3rd and 5th harmonic distortions (HD) were studied. The results show that configurations with 40 tapes and gaps of more than 2 mm are considered suitable for safe current transport under DC conditions. On the other hand, increasing the tape spacing leads to an increase in the safe transport current ripple due to the reduced magnetic field interaction within the stack. In addition, the transport loss decreases as the air gap increases due to the reduction in the self-field, whereas it increases as the number of strips increases. The influence of the 3rd HD on the transport loss is minimal at a ripple current of 1% and slightly noticeable at 2%. However, it becomes more obvious as the ripple current approaches the critical value. Remarkably, even cases with equivalent total HD show significantly higher transport losses when characterised by higher 5th HD than their counterparts with 3rd HD. This comprehensive analysis provides valuable information on the performance characteristics of HTS stacks in all-electric aircraft busbar applications and offers important insights for the development and optimisation of these systems in practical aerospace applications.

Signs of dynamic nonlinearity of the coal dielectrics depolarization upon excitation in electric and magnetic field

The authors conducted a series of experiments on samples treated immediately before measurements with a constant magnetic field of a neodymium magnet and/or an alternating electric field. The experiment has shown complex dynamics of electric potential with alternating polarity relative to the base exponential depolarization curve. The variety of responses to different types of excitation, and the irregular and unpredictable nature of fluctuations suggest that these are varieties of the same phenomenon – the nonlinear dynamics of ferroelectric domains. The applied methods of statistical processing of the cumulative data array suggest that the invariance of the relaxation dynamics of the accumulated electric potential after excitation can be characterized by three related nonlinear differential equations of the first order. The impact of an alternating electric field may consist in bringing the dipoles of ferroelectric domains in the molecular coal structure into a state of unstable equilibrium with their slow return to their original position. The impact of a constant magnetic field is determined by the interaction of the external magnetic field with the magnetization induced due to time-varying electric polarization. In any case, the observed fluctuations are due to changes in the domain structure topology of the condenser with coal matter.

Magnetic-induced chiral dynamics in an extended two-leg bosonic ladder

The realization and detection of chiral physics with ultracold atomic gases provide a unique path for the exploration of topological phases. Here, we show that the interplay of magnetic field and interacting particles in an extended two-leg ladder leads to rich chiral Bloch dynamics. Considering both the on-site contact interaction and nearest-neighbor interactions, the ground state and Bloch dynamics of the system are studied analytically and numerically. When the system is in the ground state, the threshold and phase diagram for the transition between zero-momentum state and plane-wave state are analytically obtained, showing the nearest-neighbor interactions along the legs and rungs have opposite impact on the ground state transition, providing new opportunity to manipulate the ground state transition. When the ladder is perturbated under an external linear force, chiral dephasing of Bloch oscillations (BOs), i.e. symmetry breaking damped BOs (the damping rate of BOs on one leg is larger than the other), are observed. This chirality is absent for vanishing the magnetic field and atomic interaction. Particularly, the chirality of damped BOs is inversed when the magnetic field (chiral current) is inversed. In addition, the damping of BOs induced by different types of atomic interactions is different, and the strength and damping rate of BOs initialized in different ground states are distinct, offering dynamic ways to detect the different ground states. Furthermore, the persistent chiral Bloch oscillations observed in single particle case is predicted analytically, which is a crucial requirement for observation and application of chiral BOs in nonlinear regime. Our results provide an interesting path towards the exploration of topological atomic superfluids.

Examination of Magnetic Field Signatures and Local Plasma Distribution Variations in Jupiter's Magnetosphere

AbstractSpinning disk of plasma results in deformation of Jupiter's magnetic field from a dipole to a magnetodisc configuration with significant radial and azimuthal components. Polar orbit of the Juno spacecraft enables a comprehensive in situ observation of Jupiter's plasmadisc at different latitudes. Observations from magnetometer and plasma distribution instruments on Juno mission were used to examine interaction of magnetic field and heavy ions in Jupiter's nightside magnetosphere. Power spectrum analysis was used to evaluate magnetic fluctuations inside and outside of the plasmadisc. Extensive radial maps of magnetic activity in Jupiter's nightside magnetosphere are presented. Comprehensive examination of magnetic fluctuations enable to identify local plasma density variations that correlate with plasma distribution count rate fluctuations. Observations of magnetic signatures together with examination of plasma distribution are used to detect features that point to plasma transport inside and outside of Jupiter's plasmadisc. This work shows that plasma in Jupiter's magnetosphere is contained near centrifugal equator and is not a subject to curvature drift that could generate ring currents. Signatures described as current sheet crossings were investigated. On close inspection these signatures show attributes that belong to stand alone formations rather than a single current sheet structure. This work shows that current flow is not an adequate mechanism to explain deformation of Jupiter's magnetic field.

Magnetic field impact on ferronanofluid laminar flow

A comprehensive understanding of the magnetic field interaction with the flow of ferronanofluids is essential to determine the heat transfer effect and the potential for use in industrial applications. The purpose of this work is to determine the effects of magnetic field orientation and intensity, as well as inertia forces, on heat transfer in the laminar flow of a ferronanofluid. The experiment involved the use of five permanent magnets positioned both below and above the flowing magnetite-based ferronanofluid. The analysis of the effect on heat transfer is carried out using the similarity numbers, Reynolds number (ratio of inertia and viscous forces), magnetic number (ratio of magnetic and inertia forces) and product of the two (ratio of magnetic and viscous forces).The findings indicate that the orientation of the magnetic field relative to temperature gradient-induced secondary motions plays a crucial role in either enhancing or inhibiting heat transfer. The magnet positioned below the flow leads to improved heat transfer, while placement above hinders it. To determine the magnetic field effect on heat transfer, the ratio of magnetic to viscous force introduced as MnRe is used. Taking the 5 % Nusselt number change as the threshold, the critical value for the orientation of magnet above the tube is MnRe = 24,000, while for the configuration with the magnet below, MnRe = 32,000 for Re = 109 and MnRe = 88,000 for Re = 150 and 163. The magnetic field effect is local and diminishes as the fluid flows, ultimately causing the heat transfer parameters to revert to their reference state. However, an increase in the ratio of inertia and viscosity forces enables the magnetic field interaction effect to propagate over a longer distance.

Effect of the magnetic field on the conductance and spin polarization in phosphorene superlattice

The spin-dependent conductance and spin polarization are investigated theoretically in a phosphorene superlattice in the presence of external magnetic field and Rashba interaction. It is demonstrate that, the spin-dependent conductance with and without spin-flip as well as spin polarization can be effectively controlled by changing the magnetic field strength and the number of the superlattice barriers. For small magnetic field strength, the conductance for with and without spin-flip shows an oscillating behavior as increasing the strength of the Rashba interaction, and by increasing the number of barriers, the oscillating behavior becomes prominent. Further, when the magnetic field is greater than a limit value, the spin conductance will be zero. The size of the spin-dependent transmission window in the phosphorene superlattice under external magnetic field decreases drastically. The magnitude, sign and behavior of the spin polarization can be tuned by the amount of the external magnetic field.

Far-field thermal radiation of layered ferromagnetic topological materials

High Chern number topological insulators can be obtained in a film of layered magnetic block system theoretically and experimentally. With nonzero Chern numbers, Chern insulators become valuable for fundamental topological physics and for improving next-generation electronic devices. We study energy and angular momentum radiation from layered topological insulators using the Dirac Fermion approach and by Green’s function method. We make a connection between radiation magnitude and topological phase transitions. We find that the magnetic exchange field, intra-layer coupling, and inter-layer interaction are efficient measures to modify the energy radiation of layered topological materials. Moreover, the magnetic exchange field is indispensable for emitting angular momentum due to the need for breaking time-reversal symmetry.

The local electronic interaction and strain effects on transverse dynamical spin susceptibility of [formula omitted]-graphyne

We present the behaviors of dynamical transverse spin susceptibilities of undoped β-graphyne monolayer using the Green’s function approach in the context of Hubbard model Hamiltonian. Such dynamical spin susceptibility is proportional to inelastic cross section of neutron beam from the layer. Specially, the effects of magnetic field, on-site coulomb repulsion strength and strain parameter on the spin excitation modes of β-graphyne monolayer are investigated via calculating correlation function of transverse components of spin density operators. Our results show the increase of absolute value of compressive strain parameter leads to move the magnetic excitation modes to higher energies. Also the intensity of peaks in inelastic cross section reduces with absolute value of compressive strain parameter. We also show that applying biaxial tensile strain causes to decrease the intensity of peaks in dynamical transverse spin susceptibility. Finally the effects of magnetic field and on-site coulomb repulsion interaction strength on frequency dependence of dynamical spin structure factor of β-graphyne layer are studied. Moreover the frequency positions of spin excitation mode of β-graphyne monolayer have been investigated due to the effects of biaxial strains, applied magnetic field and Hubbard parameter strength in details.

New closed-form exact solution of action induced magnetic field and fluid wall interaction on radiative mixed convective heat transfer MHD fluid flow inside a vertical walls with suction/injection and pressure gradient

The novelty of this article is not only the adaptation of a new closed-form exact method originally used to solve initial value problems but also to solve boundary value problems whose boundary conditions contain variable values. The boundary conditions of governing equations of velocity, induced magnetic, and temperature for the current study contain different parameters such as (Wall ambient temperature, Knudsen number, and Fluid wall interaction parameter) and, contain gradient of velocity, induced magnetic, and temperature. Using the Laplace transform method, the exact solution of the governing equations was obtained, and the effects of different parameters on its behavior in three different cases of wall-ambient temperature difference ratio was studied. I would also like to clarify that the reason for paying attention to such studies is that they contribute effectively and usefully in many fields and applications, such as molten metal MHD pumps, the design of small pumps, molten salt, and heat exchangers.

Magnetic manipulation of the reactivity of singlet oxygen: from test tubes to living cells

ABSTRACT Although magnetism undoubtedly influences life on Earth, the science behind biological magnetic sensing is largely a mystery, and it has proved challenging, especially in the life sciences, to harness the interactions of magnetic fields (MFs) with matter to achieve specific ends. Using the well-established radical pair (RP) mechanism, we here demonstrate a bottom-up strategy for the exploitation of MF effects in living cells by translating knowledge from studies of RP reactions performed in vitro. We found an unprecedented MF dependence of the reactivity of singlet oxygen (1O2) towards electron-rich substrates (S) such as anthracene, lipids and iodide, in which [S˙+ O2˙−] RPs are formed as a basis for MFs influencing molecular redox events in biological systems. The close similarity of the observed MF effects on the biologically relevant process of lipid peroxidation in solution, in membrane mimics and in living cells, shows that MFs can reliably be used to manipulate 1O2-induced cytotoxicity and cell-apoptosis-related protein expression. These findings led to a ‘proof-of-concept’ study on MF-assisted photodynamic therapy in vivo, highlighting the potential of MFs as a non-invasive tool for controlling cellular events.

Off‐label application of the breast expander magnet: An alternative approach to enable localisation and removal of ferromagnetic subcutaneous foreign bodies

AbstractObjectiveIncluded foreign bodies of a metallic nature are commonly found. They are often small, asymptomatic, with few or non‐visible scars or even clinically invisible. Sometimes the patient does not remember their existence. The condition is benign and does not require special attention, unless a magnetic resonance imaging scan is necessary. Indeed, magnetic field interactions could pose significant risks, and the procedure is typically contraindicated unless the ferromagnetic foreign body (FFB) has been previously removed. For such purposes, the magnet that is commonly used in breast and plastic surgery units for breast expanders port injection site identification could represent a time‐saving and cost‐effective solution.MethodologyThis paper presents an alternative technique based on off‐label application of the breast expander magnet to localize FFBs.ResultsBetween April 2023 and June 2023, the breast expander magnet allowed successful pre‐operative localisation and intra‐operative guidance for removal of FFBs in four clinical cases. The post‐operative ultrasound confirmed the absence of metal residues after the procedure in all cases.ConclusionOff‐label application of the breast expander magnet allows for FFB pre‐operative localisation and safe intra‐operative surgical guidance, thus representing a promising off‐label application of the device. After surgical removal of FFBs, the magnetic resonance imaging is allowed without any risk.

Constraining the Influence of Callisto's Perturbed Electromagnetic Environment on Energetic Particle Observations

AbstractThis study focuses on constraining the role that Callisto's perturbed electromagnetic environment had on energetic charged particle signatures observed during the Galileo mission. To do so, we compare data from the Energetic Particle Detector (EPD) obtained during four close encounters of the moon with a model framework that combines hybrid simulations for low‐energy plasma and test‐particle tracing simulations for high‐energy particles. By comparing model results for energetic particle dynamics in both uniform and perturbed electromagnetic fields, we systematically disentangle the role that geometric effects (i.e., absorption of particles by Callisto's solid surface) have on observed energetic particle signatures compared to those associated with Callisto's perturbed electromagnetic environment (generated by the moon's induced magnetic field and plasma interaction currents). We show that observed flux drop‐outs in the energetic ion pitch angle distributions (PADs) are largely driven by their absorption by Callisto's surface: their large gyroradii exceed the size of the moon, facilitating their impact onto the icy surface and preventing their detection by EPD. However, features observed in the energetic electron PADs can only be explained with an accurate representation of the moon's perturbed environment, since electrons closely follow the orientation of the electromagnetic fields. Our findings therefore illustrate the key role that the moon's induced field and magnetospheric plasma interaction have on the dynamics of energetic electrons, emphasizing the importance of accurately modeling Callisto's locally perturbed electromagnetic environment when attempting to interpret data from past and future encounters, including those anticipated from the upcoming JUICE mission.

Combined effect of rashba spin-orbit interaction, hydrostatic pressure and temperature on energy dispersion based ballistic conductance of InAs tunnel-coupled (double) quantum wire under exterior magnetic and electric field

In this work the change in energy dispersion curve and ballistic conductance for InAs tunnel-coupled double quantum wire (DQWR) under the influence of the external magnetic field, electric field, hydrostatic pressure, temperature, and Rashba spin-orbit interaction (SOI) are studied theoretically in detail. A constant magnetic field transverse to the fundamental plane is applied to the DQWR. The Landuer-Büttiker formalism is used to determine the transport characteristics, and the energy eigenvectors and eigenvalues are derived within the parameters of the diagonalization approach. The numerical results indicate that the energy spectra of the system are influenced by external factors such as magnetic field, electric field, temperature, hydrostatic pressure, and Rashba SOI, resulting in variations in lateral/vertical and downward/upward shifts. These factors also cause oscillatory patterns in ballistic conductance due to the oddity of energy subbands. These results have significant implications for the advancement of double-quantum wire-based devices.

Modeling and Simulation of a High-Performance Magnetic Biosensor for Biomedical Sensing

The current magnetic-based biosensor technologies are expensive and intricate, making them unsuitable for meeting the requirements of point-of-care medical diagnosis. This research introduces a straightforward magnetic biosensor architecture that includes an L-shaped ferromagnetic core with UL dimensions. The design involves an air gap being replaced with highly porous aluminum or copper foam, offering a potentially cost-effective and uncomplicated solution for point-of-care diagnosis based on the magnetic field effect. The foam serves as a medium for hosting biological samples, such as proteins and DNA, which are labeled with high-permeability ferromagnetic nanoparticles. The biosensor operates by detecting labeled biological molecules through magnetic field interactions. The electrical parameters of the system underwent methodical optimization to enhance overall performance. The investigation delved into the influence of various materials on the magnetic properties of the air gap. It also examined the relationships between permeability, output-induced voltage, input voltage, and input frequency. The findings reveal that utilizing materials with elevated magnetic permeability, such as Magnetite (Fe3 O4 ) or Cobalt ferrite (CoFe2 O4 ) ferrofluids, significantly enhances the biosensor's performance by optimizing magnetic coupling between primary and secondary windings. This innovative magnetic biosensor exhibits potential applications in diverse fields, including molecular biology and medical diagnostics. The study contributes valuable insights into the design and optimization of magnetic biosensors, offering opportunities for heightened sensitivity and selectivity in the detection of ferromagnetic nanoparticles labeled biomolecules such as DNA or proteins.

Spin-orbit-coupled fractional oscillators and trapped Bose-Einstein condensates.

We study the ensemble of pseudo-spin 1/2 ultracold bosons, performing Lévy flights, confined in a parabolic potential. The (pseudo-) spin-orbit coupling (SOC) is additionally imposed on these particles. We consider the structure and dynamics of macroscopic pseudospin qubits based on Bose-Einstein condensates, obtained from the above "fractional" bosons. Under "fractional" we understand the substitution of the ordinary second derivative (kinetic energy term) in the Gross-Pitaevskii equationby a so-called fractional Laplacian, characterized by the Lévy index μ. We show that the joint action of interparticle interaction, SOC, and Zeeman splitting in a synthetic magnetic field makes the dynamics of corresponding qubit highly nontrivial with evident chaotic features at both strong interactions and Lévy indices μ→1 when the Lévy trajectories of bosons with long jumps dominated over those derived from ordinary Gaussian distribution, corresponding to μ=2. Using analytical and numerical arguments, we discuss the possibilities to control the above qubit using the synergy of SOC, interaction strength, and "fractionality," characterized by the Lévy index μ.

Evaluation of weak discontinuity in rotating medium with magnetic field, characteristic shock and weak discontinuity interaction

Abstract In this article we investigated the characteristic shock and weak discontinuity wave in a rotating medium of perfect gas in the case of one-dimensional (1-D) adiabatic motion under an axial magnetic field governed by the system of PDEs (partial differential equations). We have obtained some classes of analytical solutions of the system of PDEs that demonstrates the time-space dependency. With change in the values of rotational parameter, adiabatic index and the ratio of initial magnetic pressure to dynamic pressure, effect on the acceleration wave’s amplitude and jump in the flow variables across the characteristic shock is analyzed in detail. We have obtained an expression for the jump in shock acceleration, the amplitudes of transmitted and reflected waves caused by the incident wave on the characteristic shock after the interaction of a weak discontinuity. It is investigated that the jump function across the characteristic shock decay effect, and goes to 0 as time t → ∞, whereas a weak discontinuity wave may culminate into a shock wave, depending on the initial amplitude value. It is also found that the shock formation time reduces due to the consideration of magnetic field or rotating medium.

Three-dimensional GRMHD Simulations of Neutron Star Jets

Neutron stars and black holes in X-ray binaries are observed to host strong collimated jets in the hard spectral state. Numerical simulations can act as a valuable tool in understanding the mechanisms behind jet formation and its properties. Although there have been significant efforts in understanding black hole jets from general relativistic magnetohydrodynamic (GRMHD) simulations in recent years, neutron star jets still remain poorly explored. We present the results from three-dimensional GRMHD simulations of accreting neutron stars with oblique magnetospheres for the very first time. The jets in our simulations are produced due to the anchored magnetic field of the rotating star in analogy with the Blandford–Znajek process. We find that for accreting stars, the star–disk magnetic field interaction plays a significant role, and as a result, the jet power becomes directly proportional to , where Φjet is the open flux in the jet. The jet power decreases with increasing stellar magnetic inclination, and finally, for an orthogonal magnetosphere, it reduces by a factor of ≃2.95 compared to the aligned case. We also find that in the strong propeller regime, with a highly oblique magnetosphere, the disk-induced collimation of the open stellar flux preserves parts of the striped wind, resulting in a striped jet.

Formulasi Analitikal untuk Pengoptimuman Ketumpatan Tork dalam Gear Magnetik

Energy efficiency is a very important consideration in vehicle design today. Minimizing weight would go a long way in this direction, as it directly contributes up to 75% of fuel consumption. Mechanical gearboxes and transmissions are components that add significantly to vehicle weight. For example, the mass of typical automotive transmissions ranges from 40 to 200 kg, depending on the size of the vehicle. In recent years, magnetic gears (MG) have gained attention as realistic alternatives to mechanical gears. MGs operate without contact, where torque amplification, reduction, and transmission are achieved through the interaction of magnetic fields, which allows for lighter designs. For practical use in automotive vehicles, MGs must be capable of transferring sufficient amounts of torque. To maintain being compact and lightweight, the torque density of the MG must be maximized. Hence, the MG needs to be designed in such a way so as to achieve high flux concentration. Torque density analysis of MGs is not trivial, and often, some trade-offs between accuracy and computational cost is required. Several methods of analysis have been used by various researchers, including Finite Element Analysis, Reluctance Network Analysis (RNA), the Quasi 3D Analytical Method, and Genetic Algorithms (GA). In this work, we examine these methods and present an analytical formulation that relates MG torque to its physical parameters. Understanding such relationships could help optimise future MG designs such that torque density can be maximised.

Nanoparticle Shape Effects of Aligned Magnetohydrodynamics Mixed Convection Flow of Jeffrey Hybrid Nanofluid over a Stretching Vertical Plate

This study investigates the nanoparticle shape effects of aligned magnetohydrodynamics (MHD) mixed convection flow of Cu-Al2O3/water-EG Jeffrey hybrid nanofluid over a stretching vertical plate. Five different shapes of nanoparticles which are spherical, cylindrical, blades, bricks, and platelets are considered in this study. The governing equations in the form of Partial Differential Equations (PDEs) had been reduced to nonlinear Ordinary Differential Equations (ODEs) by using similarity transformation. The solver bvp4c in MATLAB software was applied to numerically solve the dimensionless governing equations towards the physical parameters which are aligned angle of magnetic field, interaction of magnetic field, mixed convection, Deborah number, volume fraction of nanoparticles, and nanoparticle shape factor. The effects of nanoparticle shapes and other relevant thermophysical parameters on fluid velocity, temperature, skin friction coefficient and Nusselt number are discussed in tables and figures. In comparison of all shapes, this study found that blade shaped nanoparticles have the highest values of skin friction coefficient and Nusselt number. The parameters blobid0.pngblobid1.pngblobid2.png and blobid3.png decrease the velocity profiles but increase the temperature profiles.

Dynamic analysis of magnetorheological damper incorporating elastic ring in coupled multi-physical fields

The elastic ring assumes a multifunctional role, crucially providing support and reshaping oil-film thickness distribution in applications such as squeeze film dampers, demonstrating its practical efficacy. In this work, a magnetorheological damper (MRD) incorporating an elastic ring is proposed for the first time to improve the performance of damper. The innovative configuration of the elastic ring magnetorheological damper (ERMRD) is fabricated and integrated into a test platform of rotor system. The multi-filed coupling dynamic model of ERMRD is developed involving magnetic field interactions governed by Kirchhoff law, magnetorheological fluid flow dynamics derived from lubrication theory, and the elastic ring deformation based on thin plate theory. The intricate influence mechanisms of elastic ring and excitation current on oil-film characteristic of ERMRD, encompassing oil-film pressure, oil-film force, oil-film stiffness and damping, are investigated in detail. To substantiate the capabilities of ERMRD, it is implemented within the rotor system and a coupled dynamic model is established using Lagrange equation. This is followed by an in-depth analysis of the dynamic response using the Newmark-β method, including a comparative assessment with the conventional MRD. The results reveal that the elastic ring and excitation current influence oil-film pressure distribution in ERMRD from different perspectives, leading the oil-film force to present diverse variation characteristics. Compared to MRD, ERMRD exhibits weaker nonlinearity and superior damping performance.