Μm Band Research Articles

Five-Wavelength-Switchable Single-Longitudinal-Mode Thulium-Doped Fiber Laser Based on a Passive Cascaded Triple-Ring Cavity Filter

A five-wavelength-switchable thulium-doped fiber laser with a fiber Bragg grating (FBG)-based five-channel transmitting Fabry-Pérot (F-P) filter and a multi-coupler based triple-ring cavity (CTRC) filter, is experimentally proposed. For the first time, a multi-channel F-P filter and specially-designed coupler-based compound cavity filter were combined to realize multi-wavelength-switchable operation, with single-longitudinal-mode (SLM) lasing for each wavelength channel in a 2 µm band fiber laser. The theoretical analysis of the CTRC filter and the principle for achieving SLM operation by corporately using the F-P filter and CTRC filter were presented in detail. The experimental results demonstrated the good performance of the proposed filters. Five lasing wavelengths (1941.13 nm, 1941.22 nm, 1941.30 nm, 1941.39 nm, and 1941.47 nm) were obtained with good switchability, and each operated in a stable SLM state. The OSNR of each lasing wavelength was higher than 50 dB, and the linewidths of all obtained wavelengths were less than 8 kHz.

Dy3+/Er3+/Tm3+ tri-doped tellurite glass with enhanced broadband mid-infrared emission

Dy3+/Er3+/Tm3+ tri-doped tellurite glass was synthesized using melt-quenching technology, and the enhanced broadband mid-infrared band luminescence around 3.0 µm was reported for the first time under the excitation of 808 nm laser diode. The broadband mid-infrared luminescence observed in the range of 2600–3200 nm comes from the spectral overlapping of Er3+:2.7 µm and Dy3+:2.84 µm emissions, while the significant enhancement is mainly contributed by the energy transfers from Er3+:4I13/2 to Dy3+:6H11/2, Er3+:4I13/2 to Tm3+:3F4 and Tm3+:3F4 to Dy3+:6H11/2 levels. Compared with Dy3+ single-doped tellurite glass, the peak intensity of this mid-infrared band luminescence in tellurite glass tri-doped with 0.5 mol% Dy2O3, 0.5 mol% Er2O3 and 1.0 mol% Tm2O3 increases by about 214%. Additionally, the spectroscopic properties of Dy3+ ions were investigated by applying Judd-Ofelt theory and the energy transfer mechanism was analyzed to understand the enhanced broadband luminescence phenomena. The obtained results reveal that Dy3+/Er3+/Tm3+ tri-doped tellurite glass is a promising lasing medium for 3.0 µm band mid-infrared broadband photonic devices.

High quantum efficiency of 1.8 μm luminescence in Tm3+ fluoride tellurite glass

In this paper, Tm3+ doped fluorotellurite glasses are synthesized by melt-quenching technique. The thermal and spectral properties of the glasses are characterized. The effect of the 1.8 μm emission properties for different Tm3+ concentrations are investigated. ΔT (153 ℃) of the glass indicates it has good thermal stability. Spectroscopic parameters of Tm3+ such as radiative transition probability, branching ratio, spectroscopic quality factor, integrated emission cross section and radiative lifetime are calculated on the basis of Judd-Ofelt analysis. The maximum half-height width corresponding to 1.8 µm broadens as Tm3+ increases and reaches a maximum of 216 nm, as well as the longer lifetime (5.68 ms). For 1.8 µm (3F4 → 3H6) emission band, the calculated Tm3+ doped fluorotellurite glass has a high quantum efficiency of 75.93%. Furthermore, the theoretical analysis of the energy transfer mechanism between Tm3+ ions were represented. Therefore, these results demonstrate that prepared Tm3+ doped fluorotellurite glass is an ideal laser material for 1.8 µm band solid-state laser applications.

A principal component analysis of polycyclic aromatic hydrocarbon emission in NGC 7023

ABSTRACT We carried out a principal component analysis (PCA) of the fluxes of five polycyclic aromatic hydrocarbon (PAH) bands at 6.2, 7.7, 8.6, 11.0, and 11.2 µm in the reflection nebula NGC 7023 comprising of the photodissociation region (PDR) and a cavity. We find that only two principal components (PCs) are required to explain the majority of the observed variance in PAH fluxes ( 98 per cent). The first PC ( PC1), which is the primary driver of the variance, represents the total PAH emission. The second PC (PC2) is related to the ionization state of PAHs across the nebula. This is consistent with the results of a similar analysis of the PAH emission in NGC 2023. The biplots and the correlations of PCs with the various PAH ratios show that there are two subsets of ionic bands with the 6.2 and 7.7 µm bands forming one subset and the 8.6 and 11.0 µm bands the other. However, the distinction between these subsets is only present in the PDR. We have also carried out a separate PCA analysis of the PAH fluxes, this time only considering variations in the cavity. This shows that in the cavity, PC2 is not related to the charge state of PAHs but possibly to structural molecular changes.

2.1 μm, 1.52 μJ square-wave noise-like pulse from an all-fiber figure-of-9 Ho-doped oscillator and single-stage amplifier.

A 2.1 μm, high energy square-wave noise-like pulse (NLP) in an all-fiber Ho-doped fiber laser is proposed, which consists of an oscillator and a single-stage amplifier. In the figure-of-9 oscillator, mode-locking is achieved based on the nonlinear amplifying loop mirror, employing a long gain fiber to provide sufficient gain in 2.1 μm band and optimizing the cavity length to obtain maximum pulse energy output. With appropriate pump power and polarization state, the oscillator emits a 175.1 nJ square-wave NLP with center wavelength of 2102.2 nm and spike width of 540 fs. The 3-dB spectral width and pulse envelope width are 11.2 nm and 6.95 ns, respectively. The single-stage amplifier employs a bi-directional pump scheme. After amplification, 5.8 W NLP with a slope efficiency of 56.8% is obtained. The pulse energy of NLP is scaled to 1.52 μJ, which is the highest pulse energy of NLP at 2.1 μm to the best of our knowledge. The obtained high-energy square-wave NLP-fiber laser has great potential in mid-infrared laser generation.

Highly optically transparent graphene mesh for electromagnetic interference shielding

The update of optoelectronic technology requires that the optical window has the dual functions of optical transparency and electromagnetic shielding. A transparent electromagnetic shielding method based on graphene mesh structure is proposed. The optical transmittance of the graphene mesh was theoretically analyzed. Graphene mesh is fabricated by ordinary mask photolithography technology to arbitrarily adjust the structure and number of layers. It retains the same properties as the unpatterned graphene film. Through mesh structure design and layer number control, graphene mesh can be used to replace graphene film with uniform thickness. The average transmittance of the four-layer graphene mesh in the 3–5 μm band is 95.26%, and the average shielding efficiency in the 12–18 GHz band is 3.86 dB. It shows that the graphene mesh maintains high optical transmittance and has good electromagnetic shielding effectiveness.

Artificial neural network model for precipitation forecast over Western Himalaya using satellite images

Kalpana satellite images in real time available by India meteorological department (IMD), contain relevant inputs about the cloud in infra-red (IR), water vapor (WV), and visible (VIS) bands. In the present study an attempt has been made to forecast precipitation at six stations in western Himalaya by using extracted grey scale values of IR and WV images. The extracted pixel values at a location are trained for the corresponding precipitation at that location. The precipitation state at 0300 UTC is considered to train the model for precipitation forecast with 24 hour lead time. The satellite images acquired in IR (10.5 - 12.5 µm) and WV (5.7 - 7.1 µm) bands have been used for developing Artificial Neural Network (ANN) model for qualitative as well as quantitative precipitation forecast. The model results are validated with ground observations and skill scores are computed to check the potential of the model for operational purpose. The probability of detection at the six stations varies from 0.78 for Gulmarg in Pir-Panjal range to 0.95 for Dras in Greater Himalayan range. Overall performance for qualitative forecast is in the range from 61% to 84%. Root mean square error for different locations under study is in the range 5.81 to 8.7.

The Dust Mass of Supernova Remnants in M31

Abstract The dust temperature and mass of the supernova remnants (SNRs) in M31 are estimated by fitting the infrared spectral energy distribution calculated from the images in the Spitzer/IRAC4 and MIPS24, Herschel/PACS70, 100, and 160, and Herschel/SPIRE 250 and 350 μm bands. Twenty SNRs with relatively reliable photometry exhibit an average dust temperature of 20.1 − 1.5 + 1.8 K, which is higher than the surrounding and indicating the heating effect of supernova explosion. The dust mass of these SNRs ranges from about 100 to 800 M ⊙, much bigger than the SNRs in the Milky Way. On the other hand, this yields the dust surface density of 0.10 − 0.04 + 0.07 M ⊙ pc−2, about half of the surrounding area, which implies that about half dust in the SNRs is destroyed by the supernova explosion. The dust temperature, the radius, and thus the dust mass all demonstrate that the studied SNRs are old and very likely in the snowplow or even fade-away phase because of the limitation by the far distance and observation resolution of M31, and the results can serve as a reference to the final effect of supernova explosion on the surrounding dust.

Efficient 4.95 µm-8.5 µm dual-band grating coupler with crosstalk suppression capability.

In many integrated optics systems, grating couplers are a key component of interfacing the external light source with in-plane photonic devices. Grating couplers with dual-band capability are often desired for expanding the operation spectrum of photonic systems. Here, we propose and theoretically investigate, for the first time, a 4.95 µm-8.5 µm dual-band grating coupler on a Ge-on-SOI platform. In addition to conventional structures, Bragg gratings are introduced to two wavelength division directions for crosstalk suppression. With this design, the simulated coupling efficiencies have respectively reached 59.93% and 46.38% for the 4.95 µm and 8.5 µm bands. This mid-infrared dual-band grating coupler may be useful for defense and environmental monitoring applications.

High concentration Tm3+ doped TeO2-Al2O3-BaF2 glass for ~ 2 µm fiber lasers

The high concentration Tm3+ ions doped fluorotellurate glass samples (TeO2-Al2O3-BaF2) fabricated by high-temperature fusion technique and the luminescence properties of the glass samples were examined based on absorption and fluorescence spectra to forecast the latent capability of TAFT4 glass for ~ 2 µm band fiber lasers. The thermodynamic properties of the glass samples utilized for drawing the optical fiber, internal structure and the maximum phonon energy were characterized based on the thermal stability parameter ΔT and Raman spectra, respectively. The Judd-Ofelt (J-O) intensity parameters (Ωt) was estimated from the recorded absorption spectral data, and the estimation results showed that the value of Ω2 was as high as 6.97 × 10−20 cm2. To reveal the spectral properties of TAFT4 glass sample, significant radiative parameters including spontaneous raditive transition probabilities (Arad), fluorescence branching ratios (β), radiative lifetimes (τrad), absorption and emission cross sections of Tm3+ ions excitation energy levels were determined using J-O intensity parameters. Furthermore, the calculation of the gain coefficient is included to determine its capability as a gain medium. The fluorescence decay behavior of Tm3+ ions and the energy transfer mechanism were investigated and analyzed in detail, and the macroscopic rate WET of the CR process between Tm3+ ions in TAFT4 glass was quantified by the transfer constants CD-D and CD-A. The value of WET was high up to 2073.4 × 10−20 cm3/s by estimation. As mentioned above, the fabricated TAFT4 glass sample may be a suitable gain medium that can be used for ~2 µm band fiber lasers.

VO2-Based Infrared Radiation Regulator with Excellent Dynamic Thermal Management Performance.

Dynamic thermal management materials attract fast-increasing interest due to their adaptability to changing environments and greater energy savings as compared to static materials. However, the high transition temperature and the low emittance tunability of the vanadium dioxide (VO2)-based infrared radiation regulators limit their practical applications. This study addresses these issues by proposing a smart infrared radiation regulator based on a Fabry-Pérot cavity structure (VO2/HfO2/Al), which is prepared by high-power impulse magnetron sputtering (HiPIMS) and has the potential for large-scale production. Remarkably, the outstanding emittance tunability reaches 0.51, and the phase transition temperature is lowered to near a room temperature of 27.5 °C by tungsten (W) doping. In addition, a numerical thermal management power of 196.3 W/m2 (at 8-14 μm band) can be obtained from 0 to 60 °C. As a proof-of-concept, the demonstrated capabilities of the VO2 infrared radiation regulator show great potentials in a wide range of applications for the thermal management of buildings and vehicles.

Imaging Considerations From a Geostationary Orbit Using the Short Wavelength Side of the Mid‐Infrared Water Vapor Absorption Band

AbstractHistorically, the long wavelength side (6–7.5 μm) of the mid‐infrared water vapor absorption band has been used for imaging from the geostationary perspective. This began with the 6.4 μm band on Europe's Meteosat‐1. While geostationary sounders for moisture profiling, including China's hyperspectral resolution infrared sounder and a planned sounder from Europe, are or will be measuring the short wavelength side of the water vapor band, this is not the case for geostationary imagers. Shorter wavelength (5–6 μm) spectral bands for imaging applications should be considered for observing moisture in the mid and lower troposphere because of several potential advantages offered by this spectral range. The short wavelength side of the water vapor band contains fewer additional absorbing gases that overlap the water vapor absorption lines. In addition, the shorter wavelengths would show less diffraction blurring which could enable finer spatial resolution for turbulence detection. This study considers some of the differences and potential advantages of the spectral information in the short wavelength side of the water vapor absorption band from the perspective of geostationary imaging. For dry conditions land heating could impact the qualitative use of observed brightness temperatures at 5.1 μm, while the solar reflection component over most clear‐sky scenes is small for a 5.1 μm band and essentially zero for a 5.6 μm band.

Structural and Infrared Spectral Modulation Properties of a CuNiAg Alloy/Ni—Ag-Doped Cu4O3 One-Dimensional Photonic Crystal

To develop a new material with low emissivity in the range of the 3–5 μm band, the present work reports a CuNiAg alloy/Ni—Ag-doped Cu4O3 one-dimensional photonic crystal prepared by reactive sputtering and correlates the effect of nickel and silver on the structural and infrared spectral properties. The morphology, structure and infrared spectral properties of the CuNiAg alloy/Ni—Ag-doped Cu4O3 1DPC were studied by FESEM, XRD, and an IR-2 dual-wavelength emissivity instrument. The doping of Ni and Ag impeded phase formation, and the Cu2O and Cu4O3 phases only appeared under the same process conditions. The doped elements caused lattice contraction and decreased the thickness of the 1DPC, which was the most important factor affecting the emissivity. The results of the emissivity measurement showed that the single period film thickness of Cu80Ni15Ag5/Ni-Ag-doped Cu4O3 was close to 280 nm, and the number of periods was 2–4. Therefore, the Cu80Ni15Ag5/Ni-Ag-doped Cu4O3 1DPC had good selective infrared properties with an average emissivity of less than 0.1 in the 3–5 μm band and larger than 0.94 in the 8–14 μm band; thus, this 1DPC is expected to be used as an infrared spectral modulation material.

Search for Hα Emitters at z ∼ 7.8: A Constraint on the Hα-based Star Formation Rate Density

Abstract We search for Hα emitters at z ∼ 7.8 in four gravitationally lensed fields observed in the Hubble Frontier Fields program. We use the Lyman break method to select galaxies at the target redshift and perform photometry in the Spitzer/IRAC 5.8 μm band to detect Hα emission from the candidate galaxies. We find no significant detections of counterparts in the IRAC 5.8 μm band, and this gives a constraint on the Hα luminosity function (LF) at z ∼ 7.8. We compare the constraint with previous studies based on rest-frame UV and far-infrared observations using the correlation between the Hα luminosity and the star formation rate. Additionally, we convert the constraint on the Hα LF into an upper limit for the star formation rate density (SFRD) at this epoch assuming the shape of the LF. We examine two types of parameterization of the LF and obtain an upper limit for the SFRD of log 10 ( ρ SFR [ M ⊙ yr − 1 Mpc − 3 ] ) ≲ − 1.1 at z ∼ 7.8. With this constraint on the SFRD, we present an independent probe into the total star formation activity including dust-obscured and unobscured star formation at the Epoch of Reionization.

Progress and Prospect of Fiber Lasers Operating at 1.7 μm Band

Progress and Prospect of Fiber Lasers Operating at 1.7 μm Band

Mode-locked fiber laser of 3.5 µm using a single-walled carbon nanotube saturable absorber mirror

We report on a mid-infrared fiber laser that uses a single-walled carbon nanotube saturable absorber mirror to realize the mode-locking operation. The laser generates 3.5 µm ultra-short pulses from an erbium-doped fluoride fiber by utilizing a dual-wavelength pumping scheme. Stable mode-locking is achieved at the 3.5 µm band with a repetition rate of 25.2 MHz. The maximum average power acquired from the laser in the mode-locking regime is 25 mW. The experimental results indicate that the carbon nanotube is an effective saturable absorber for mode-locking in the mid-infrared spectral region.

A Laboratory-driven Multiscale Investigation of X-Ray Induced Mass Loss and Photochemical Evolution in Cosmic Carbon and Silicate Dust

Abstract We present the results of an integrated laboratory and modeling investigation into the impact of stellar X-rays on cosmic dust. Carbonaceous grains were prepared in a cooled (<200 K) supersonic expansion from aromatic molecular precursors, and were later irradiated with 970 eV X-rays. Silicate (enstatite) grains were prepared via laser ablation, thermally annealed, and later irradiated with 500 eV X-rays. Infrared spectra of the 3.4 μm band of the carbon sample prepared with benzene revealed 84% ± 5% band area loss for an X-ray dose of 5.2 ×1023 eV.cm−2. Infrared spectra of the 8–12 μm Si–O band of the silicate sample revealed band area loss up to 63% ± 5% for doses of 2.3 × 1023 eV.cm−2. A hybrid Monte Carlo particle trajectory approach was used to model the impact of X-rays and ensuing photoelectrons, Auger and collisionally ionized electrons through the bulk. As a result of X-ray ionization and ensuing Coulomb explosions on surface molecules, the calculated mass loss is 60% for the carbonaceous sample and 46% for the silicate sample, within a factor of 2 of the IR band loss, supporting an X-ray induced mass-loss mechanism. We apply the laboratory X-ray destruction rates to estimate the lifetimes of dust grains in protoplanetary disks surrounding 1 M ⊙ and 0.1 M ⊙ G and M stars. In both cases, X-ray destruction timescales are short (a few million years) at the disk surface, but are found to be much longer than typical disk lifetimes (≳10 Myr) over the disk bulk.

Transferable single-layer GeSn nanomembrane resonant-cavity-enhanced photodetectors for 2 μm band optical communication and multi-spectral short-wave infrared sensing.

Semiconductor nanomembranes (NMs) have emerged as an attractive nanomaterial for advanced electronic and photonic devices with attractive features such as transferability and flexibility, enabling heterogeneous integration of multi-functional components. Here, we demonstrate transferable single-layer GeSn NM resonant-cavity-enhanced photodetectors for 2 μm optical communication and multi-spectral short-wave infrared sensing/imaging applications. The single-layer strain-free GeSn NMs with an Sn concentration of 10% are released from a high-quality GeSn-on-insulator (GSOI) substrate with the defective interface regions removed. By transferring the GeSn NMs onto a predesigned distribution Bragg reflector (DBR)/Si substrate, a vertical microcavity is integrated into the device to enhance the light-matter interaction in the GeSn NM. With the integrated cavity and high-quality single-layer GeSn NM, a record responsivity of 0.51 A W-1 at 2 μm wavelength at room temperature is obtained, which is more than two orders of magnitude higher than the reported values of the multiple-layer GeSn membrane photodetectors without cavities. The potential of the device for multi-spectral photodetection is demonstrated by tuning the responsivity spectrum with different NM thicknesses. Theoretical simulations are utilized to analyze and verify the mechanisms of responsivity enhancement. The approach can be applied to other GeSn-NM-based active devices, such as electro-absorption modulators or light emitters, presenting a new pathway towards heterogeneous group-IV photonic integrated circuits with miniaturized devices.

Preparation and Properties of a Kind of Tellurium Bismuthate Mid-infrared Luminescent Composite Glass

The band of infrared luminescence includes atmospheric windows of 1-3μm, 3-5μm, and 8-14μm, covering many important characteristic spectra. Therefore, the luminescent materials in this band are used in biomedical, satellite remote sensing, weapon guidance, industrial processing, Weapon penetration and other fields have broad application prospects. In this paper, the preparation method of doped bismuth telluride composite glass material was studied, and the luminescence properties of infrared luminescent composite glass in the 2.7μm band mid-infrared laser in the matrix material. In this paper, the TeO2-Nb2O5-Bi2O3 glass system was selected as the matrix glass to prepare the tellurate infrared emitting composite glass. The Bi3.20Te0.80O6.40 crystal is a three-dimensional growth method, and the nucleation and growth process of the glass-ceramic is a diffusion mechanism, which belongs to the crystallization behavior mainly controlled by diffusion. Transparent bismuth telluride composite glasses with different doping concentrations of rare earth ions were prepared by a two-step heat treatment method. The infrared luminescent composite glass prepared in this paper has strong penetrating ability to smoke and atmosphere, good transmission confidentiality and low loss, and has important application prospects in radar systems, infrared remote sensing, laser ranging and other fields. The final results of the study show that, by comparing the melting and purity of chemical reagents, it can be seen that the melting time consumed by bismuth oxide is 45 minutes, and a purity of 95.5% can be obtained. The time is shorter, which is conducive to reducing a certain cost.

Dust Properties of Two New Cavity Structures Nearby Asymptotic Giant Branch Stars: The IRAS Survey

We studied the dust properties of two cavity structures (namely FIC21+54 and FIC16-56) nearby Asymptotic Giant Branch stars using Infrared Astronomical Satellite (IRAS) maps. Dust color temperature, Planck function, dust mass, and visual extinction with their distribution within the region of interest were examined. The temperature of dust was found to lie in the range of 22.24 ± 0.81 K to 23.27 ± 0.21 K, and 25.12 ± 0.43 K to 26.17 ± 0.62 K, and the mass of dust was obtained within the range of 4.21 × 1026 kg to 3.6 × 1027 kg, and 2.1 × 1027 kg to 3.31 × 1028 kg, for FIC21+54 and FIC16-56, respectively. Some unusual behaviors on the distribution of dust temperature indicated the effect of nearby sources within the studied structures. Moreover, we observed the trend of dust particles along the major and minor diameters, and plots represented that the particles were oscillating with a sinusoidal pattern in both cavities. The negative slope between 25 µm and 60 µm in far-infrared spectral distribution was encountered for both structures, which portrayed less number density of particles in 60 µm band; interaction between AGB wind and the ambient interstellar medium could be the possible reason behind this. These findings support the prior results for two new cavity structures nearby AGB stars within the galactic plane -10° < b < +10°.