Lower Surface Roughness Values Research Articles

Effects of abrasive grain size of flexible body-armor-like abrasive tool (BAAT) on high-shear and low-pressure grinding for zirconia ceramics

Zirconia ceramics exhibit remarkable performance. However, the high hardness and brittleness poses enormous challenges for machining. This study is integrally focused on preparing a flexible body-armor-like abrasive tool (BAAT) with enhanced tangential-to-normal force ratio. The rheological characteristics of the BAAT abrasive system with different abrasive grain were investigated. A series of grinding tests were conducted on a precision grinding machine. The grinding performance of the BAAT with different abrasive grain sizes was examined. Surface roughness (Ra) variation and tangential-to-normal force ratio were analyzed, together with the investigation of the three-dimensional surface morphology and surface hydrophilicity. It was found that smaller abrasive grain sizes ultimately generated lower surface roughness values after grinding. Under the optimal grinding conditions, the surface roughness (Ra) of zirconia ceramics decreased from 102 nm to 1.7 nm after 5 grinding strokes (∼1 min). Meanwhile, uniform grinding textures were obtained.

Fused filament fabrication using stainless steel 316L‐polymer blend: Analysis and optimization for green density and surface roughness

AbstractThis study is centered on the analysis of composite component additive manufacturing, via fused filament fabrication (FFF), comprising of 316L stainless steel particles in a polymer matrix. It examines the impact of several process factors of FFF, including extrusion speed, layer height, and extrusion temperature, on the density and surface roughness with the goal to minimize porosity. The independent and interaction impacts of these parameters were investigated using a central composite design technique. The technique of analysis of variance was utilized to determine the influence of relevant factors. Regression analysis was used to establish statistical models linking the parameters to green density and surface roughness. The green density was enhanced by reducing the layer height from 0.2 to 0.1 μm and decreasing the nozzle speed from 100 to 20 mm min−1. The surface roughness was improved by using a slow printing speed and minimum layer height. The ideal temperature range for producing favorable results in terms of green density and surface roughness during extrusion was found to be between 235 and 240°C. Significant correlations were found between the parameters and the green density and surface roughness. A genetic algorithm was used as an optimisation tool to determine the thresholds that would provide the highest green density and the lowest surface roughness values. The porosity of the samples generated with the optimized settings was evaluated using microtomography scans. The methodology presented here can be applied to composite and standard polymeric filament printing to determine optimal printing parameters.Highlights Blend of stainless steel 316L and polymer was used for fused filament fabrication. Printing speed and layer height were the dominating for density and roughness. Height 0.2 mm, speed 20 mm s−1, and temperature 239°C resulted 4.73 g cm−3 density and 21.09 μm roughness Microtomography revealed porosity of 1.7% in the optimized sample.

The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis.

The aim of this study is to evaluate the surface roughness (SR) and color changes of single-shade and nanohybrid resin-based restorative materials (RBC) after immersion in liquids at different pH values. For RBCs, a total of 120 specimens, 30 for each material, were prepared using 10 mm diameter and 2 mm thick molds. For flowable bulk fill RBC, a total of 40 specimens, 10 for each material, were prepared using 10 mm diameter and 4 mm thick molds (n = 10). After initial color and SR measurements, samples were stored in the liquids for 14 days and all of the measurements were repeated on 14th days. Scanning electron microscopy and atomic force microscopy analyzes were performed in all groups. When SR results are examined; among all liquids, the highest SR value was observed in the Carisma Diamond One (CDO) group, while the lowest SR value was observed in the Omnichroma Flow Bulk (OMF) group (p < .05). When the color changes (ΔE) results are examined; it was observed that CDO group had highest color change and OMF group had the lowest values. It has been observed that among the liquids, the liquids that affect the ΔE values of the materials the most are coffee and cola. When the ΔE values of the subgroups of the materials were examined, there was a statistically significant difference in all subgroups of RBCs (p < .05). While acidic liquids increased the SR of RBCs, coffee more affected the color change of RBCs. RESEARCH HIGHLIGHTS: Clinicians should keep in mind that the RBCs tested may change their surface properties and colors when exposed to various liquids. People who have RBCs should pay attention to the consumption of acidic and highly pigmented liquids.

Effect of the incorporating of refractory NbC precipitates in intermetallic iron-aluminide coatings on corrosion and high-temperature oxidation behavior

This study aims to investigate the effects of growing niobium carbide (NbC) particles into intermetallic iron-aluminide (FeAl) coatings on ductile cast iron (SGI) by thermo-reactive diffusion technique (TRD). The study compares the corrosion and oxidation behavior of the FeAl-NbC coatings with SGI, FeAl, and NbC coatings. Corrosion tests were conducted through polarization tests in a 3.5 wt% NaCl solution, while oxidation tests were performed at 900 °C for 4, 16, and 64 h. Before and after corrosion and oxidation tests, the coatings were examined using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The findings show that FeAl coatings with NbC particles had lower graphite nodules, porosity, and surface roughness values compared to FeAl coatings. FeAl-NbC composite coatings provided better corrosion and oxidation resistance compared to untreated SGI, FeAl, and NbC coatings. The results of the comparative analysis of FeAl-NbC, FeAl, NbC, and untreated SGI specimens indicate that corrosion resistance in a 3.5 wt% NaCl solution and oxidation resistance at 900 °C followed the order FeAl-NbC > FeAl > NbC > SGI.

Effect of pulse time (Ton), pause time (Toff), peak current (Ip) on MRR and surface roughness of Cu–Al–Mn ternary shape memory alloy using wire EDM

Shape memory and super elasticity are two outstanding properties of Cu–Al–Mn SMAs together with additional copper-based shape memory alloys that make them superior to NiTi alloys. It's quite hard to machine Cu–Al–Mn SMA. The machinability properties of Cu–Al–Mn SMAs during Wire Electrical Discharge Machining (WEDM) were experimentally investigated using molybdenum wire as the electrode material. Material Removal Rate (MRR) and Surface Roughness (SR) are two machining qualities that are studied in relation to the combinational values of pulse time (Ton), pause time (Toff), and peak current (Ip), which are selected as the changeable input process factors. From the experimental investigation, it was found that both MRR and Ra values were increased with an increase in pulse on time(Ton), pulse off time(Toff), and peak current (IP)values. Because the wire electrode contains maximum current under these conditions, it is easy to remove more material at the tool and work material interface, resulting in moderate surface finish. Surface quality was higher on samples machined at low energy input than it was on samples machined at high energy input. This SEM micrograph clearly shows that a lower pulse on time produces a superior surface quality.SEM images and the analysis of the machined surface morphology on the surface of the CAM7 alloy clearly showed that the machined surface of the alloy had a lower surface roughness value at a lower Ip-2A and was associated with a higher surface roughness value at a higher Ip-6A, as well as a lot of uncleared debris and blow holes.

Development and electrochemical investigations of enhanced corrosion-resistant Polyvinylcarbazole-TiO2 hybrid nanocomposite coatings on 316L SS for marine applications

The present study focuses on evaluating the corrosion resistance of 316L stainless steel substrates with Polyvinylcarbazole (PVK)/TiO2 hybrid nanocomposite coatings (HNC). Using the chronoamperometry approach, the HNC were electrochemically synthesized on 316L stainless steel substrates, incorporating various weight (%) 1 %, 2 %, 3 % of TiO2 nanoparticles into the PVK matrix. The findings of the surface morphology investigation verified that the 316L SS had a dense and smooth PVK/TiO2 coating. A low surface roughness and high contact value of the PVK/TiO2 coatings are also responsible for the decrease in corrosion rate of the 316L SS. The corrosion protection efficiency of the PVK/TiO2 HNC were investigated through open circuit potential (OCP) measurement, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) analysis in 3.5 wt% NaCl solution. The corrosion rate obtained from the polarization studies of the HNC coatings as follows PVKT-2 < PVKT-3 < PVKT-1 < PVK < 316L SS. Results revealed that an optimal loading of 2 wt% TiO2 nanoparticles significantly enhanced the corrosion resistance of the coating. The enhanced electrochemical impedance response for PVK/TiO2 coatings was verified by EIS experiments. The study demonstrates that the incorporation of TiO2 nanoparticles into the PVK matrix effectively creates a barrier layer at the coating-metal interface, inhibiting the entry of aggressive ions. Microhardness studies revealed the increase in hardness value of the PVK and PVK/TiO2 coatings indicated the protective nature of the coating and provided high mechanical strength to 316L SS. The tape adhesion tests carried out on the coated specimens also indicated a good adhesion of the PVK/TiO2 on the 316L SS surface.

Experimental and statistical investigation of electro-erosion machining performance of cryogenic treated hardened AISI H13 hot work tool steel

This study investigated the machinability of AISI H13 hot work tool steel with a hardness of 54 HRC, which has been deep cryogenically treated using the electro-erosion machining technique, one of the unconventional manufacturing methods. The machinability parameters used in the study were determined as current (4, 8 and 12 A), pulse time (200, 300 and 400 µs) and three different electrodes (Copper, Graphite and Tuncop). The experimental design was designed according to the Taguchi L27 model, and machinability tests were carried out to examine the results obtained from the experimental study both experimentally and statistically. When the literature was examined, it was seen that cryogenic treatment was generally applied to electrode materials, and only surface roughness and material wear amounts were examined as output parameters. The original value of the study is the interpretation of the results by applying cryogenic treatment to the test material and exploring the surface roughness and material wear amount, as well as the hole diameters and criterion diameters formed on the treated surfaces after the EDM process. As a result of the study, it was observed that the surface roughness value, the hole diameter, the amount of material wear, and the crater diameter increased with the increase in ampere and impact time. The lowest surface roughness value was 2.266 µm in the graphite electrode material at 4 amps and 200 µs impact time and the highest wear amount was realized as 0.555 g in the copper electrode material 12 amps and 400 µs impact time. The smallest hole diameter was 12.254 mm with a tuncop electrode with a pulse duration of 4 amps and 200 µs, and the lowest crater diameter was 127.301 µm with a graphite electrode at a current of 4 amps and a pulse duration of 200 µs. When the signal-to-noise ratios were examined, the optimum machining parameters for surface roughness, hole diameter, material wear amount, and crater diameter were determined as A2B1C1, A1B3C3, A3B1C1, and A3B1C1, respectively. When the ANOVA results are examined, it is determined that the most effective parameter for the surface roughness is of the current value with 86.54%, the most effective parameter for the hole diameter is the electrode material with 85.20%, the most effective parameter for material wear amount is the electrode material with 45.67% and the most effective parameter for the crater diameter is current value with 75.35%.

Effect of Incorporation of Poly Vinyl Pyrrolidone on Transverse Strength, Impact Strength and Surface Roughness of Autopolymerizing Acrylic Resin

Autopolymerizing acrylic resin is one of the most frequently used materials in dentistry, but it has relatively poor mechanical properties This study investigated the effect of the addition of poly vinyl pyrrolidone on transverse strength, impact strength and surface roughness of autopolymerzing acrylic resin. A total of 60 specimens were prepared, 30 specimens of each conventional and modified autoplymerizing acrylic.20 specimens of each groups were fabricated with dimensions of (64×10×2.5) mm to conduct the transverse strength and surface roughness tests, while the remaining 10 specimens of each group were fabricated with dimensions of (80×10×4) mm to perform the impact strength test. The results of this study showed that the modified autopolytmerized acrylic had significantly higher transverse strength, and significantly lower surface roughness values while there was no significant differences in impact strength value. It can be concluded that addition of Polyvinylpyrrolidone can improve transverse strength and surface roughness of autopolymerizing acrylic resin.

Osteoblast Attachment on Bioactive Glass Air Particle Abrasion-Induced Calcium Phosphate Coating.

Air particle abrasion (APA) using bioactive glass (BG) effectively decontaminates titanium (Ti) surface biofilms and the retained glass particles on the abraded surfaces impart potent antibacterial properties against various clinically significant pathogens. The objective of this study was to investigate the effect of BG APA and simulated body fluid (SBF) immersion of sandblasted and acid-etched (SA) Ti surfaces on osteoblast cell viability. Another goal was to study the antibacterial effect against Streptococcus mutans. Square-shaped 10 mm diameter Ti substrates (n = 136) were SA by grit blasting with aluminum oxide particles, then acid-etching in an HCl-H2SO4 mixture. The SA substrates (n = 68) were used as non-coated controls (NC-SA). The test group (n = 68) was further subjected to APA using experimental zinc-containing BG (Zn4) and then mineralized in SBF for 14 d (Zn4-CaP). Surface roughness, contact angle, and surface free energy (SFE) were calculated on test and control surfaces. In addition, the topography and chemistry of substrate surfaces were also characterized. Osteoblastic cell viability and focal adhesion were also evaluated and compared to glass slides as an additional control. The antibacterial effect of Zn4-CaP was also assessed against S. mutans. After immersion in SBF, a mineralized zinc-containing Ca-P coating was formed on the SA substrates. The Zn4-CaP coating resulted in a significantly lower Ra surface roughness value (2.565 μm; p < 0.001), higher wettability (13.35°; p < 0.001), and higher total SFE (71.13; p < 0.001) compared to 3.695 μm, 77.19° and 40.43 for the NC-SA, respectively. APA using Zn4 can produce a zinc-containing calcium phosphate coating that demonstrates osteoblast cell viability and focal adhesion comparable to that on NC-SA or glass slides. Nevertheless, the coating had no antibacterial effect against S. mutans.

Analysis of Polyurethane Foam Machining Parameter Influence: Current Status and Perspective

Nowadays, polyurethane (PU) foam has successfully replaced various engineering materials in many applications due to its many advantages in mechanical and thermal properties. In various applications, PU foam must be formed into various 3-dimensional models according to user requirements by utilizing CAM software and CNC milling machining to manufacture a product. Thus, the selection of cutting parameters in the milling machining process in terms of the nature and character of the material and cutting tools is essential and significantly influences the geometric structure and surface roughness of the PU foam products produced. Based on the review of this article, several machining parameters must be appropriately considered, including spindle rotation speed, depth of cut, cutting tool selection, and feed rate. Vibration will increase as the spindle rotation speed increases, which brings cutting tools but results in better surface quality. Continuous chip formation can be achieved by selecting the proper cut depth and producing low surface roughness values. Selecting suitable cutting tools and geometries that match the material characteristics can reduce the risk of material damage during the machining process, thereby reducing the surface roughness value. Finally, a low cutting rate will minimize surface roughness but increase the risk of cutting-edge wear.

Effects of Cutting Parameters and Grain Direction on Surface Quality of Three Wood Species Obtained by CNC Milling

Computer Numerical Control (CNC) machines are increasingly popular in the production of furniture and wood products, because they combine high processing quality with short production time. The effective use of CNC machines depends on the processing parameters, which also affects the quality of the processed surface. The aim of this study was to determine the effect of feed rate, cutting direction, and grain direction on the surface roughness of various types of wood. Three European wood species (oak, beech, fir) were cut with a spindle speed of 16,000 rpm and two different feed rates (5,000 and 10,000 mm/min) using end mill tools on the CNC machine. The milling was performed in two cutting directions (radial and tangential) and two grain orientations (0° and 90°). An analysis of variance (ANOVA) was performed to evaluate the impact of the cutting parameters. The surface roughness measurements were taken, and two surface roughness parameters (Ra and Rz) were measured to determine the surface quality of the wood. According to the results of this study, the lowest surface roughness values, milling with the same processing parameters, occurred for oak wood, while the highest values occurred for fir.

Corrosion Resistance of NiS, ZnS and NiS/ZnS Thin Films Deposited by Spray Pyrolysis Technique on Low Carbon Steel in 3.5% Nacl Solution

Abstract In this work, the main object of this research is to investigate a new material based on ZnS and NiS nanostructures. NiS and ZnS solutions were sprayed on the heated Low Carbon Steel by a spray pneumatic deposition method. Electrochemical analyses of the prepared samples were investigated. The high corrosion resistance of coated by ZnS sample have a low value of surface roughness. However, the coated sample by ZnS also has good stabilization after corrosion and high compact of the film.

Surface Roughness Optimization of Selective Laser Melting Printed 17-4 PH Stainless Steel Parts

The 17-4 PH stainless steel possesses distinguished applications due to its inherent properties. Higher surface roughness in Selective Laser Melting (SLM) parts limits their use in a wide range of applications. Higher surface roughness deteriorates the important functional properties (strength, fatigue, corrosion resistance and so on). Therefore, an attempt is being made to reduce the surface roughness during the processing stage itself, rather than the dependency of costly secondary post-processing routes. Taguchi L9 experiments are conducted to analyze the laser power, scan speed and hatch distance influence on the surface roughness of SLM parts. Laser power showed the highest percentage contribution equal to 83.37%, followed by scan speed of 9.92% and hatch distance of 6.71%, respectively. Taguchi method determined optimal conditions (laser power: 270 W, scan speed: 1000 mm/s and hatch distance: 0.08 mm) through Pareto analysis of variance resulted in low values of surface roughness with a value equal to 4.11 µm. The results of the optimal condition can be used by any novice user to obtain better surface quality in SLM parts. Further, the Taguchi method can be applied to optimize any process with limited experimental trials and resources.

Influencing effect of minerals composition in natural granite rocks on surface roughness

The machining of natural rocks is gaining ground in art and architecture. However, the parameters influencing the design of surfaces with low surface roughness values are still the subject of research. In this study, we analysed the composition of granite specimens to examine their effect on surface roughness. 5 different granite samples were milled and then examined with XRD equipment. Minerals on the surface were analysed by light microscopy and scanning electron microscopy. Then the surface area of the minerals was measured with a 3D imaging system for surface roughness. Based on the obtained results, we examined the amount of constituents of each mineral and the value of the surface roughness of the minerals. The results showed that changes in certain mineral constituents affect the value of surface roughness during machining. By this, the expected surface roughness value of the rocks can be predicted based on the composition.

Gastric acid challenge of lithium disilicate–reinforced glass–ceramics and zirconia-reinforced lithium silicate glass–ceramic after polishing and glazing—impact on surface properties

ObjectivesTo investigate the impact of simulated gastric acid on the surface properties of lithium disilicate–reinforced glass–ceramics and zirconia-reinforced lithium silicate glass–ceramic after certain polishing and glazing procedures.Materials and methodsFour different types of square-shaped specimens (10 × 10 × 2 mm3, n = 13) were manufactured: lithium disilicate–reinforced glass–ceramic milled and polished (LDS-P); milled, polished, and glazed (LDS-PG); milled, glazed, and no polishing (LDS-G); and milled and polished zirconia-reinforced lithium silicate glass–ceramic (ZR-LS). Specimens were immersed in hydrochloride acid (HCl 0.06 M, pH 1.2) to simulate gastric acid irritation and stored in the acid for 96 h in 37 °C. Specimen weight, surface gloss, Vickers surface microhardness and surface roughness (Ra, Rq, with optical profilometer), and surface roughness on nanometer level (Sq, Sal, Sq/Sal, Sdr, Sds with atomic force microscope) were measured before and after the acid immersion.ResultsZR-LS specimens lost significantly more weight after acid immersion (p = 0.001), also surface microhardness of ZR-LS was significantly reduced (p = 0.001). LDS-G and LDS-PG showed significantly lower surface roughness (Sa, Sq) values compared to LDS-P before (p ≤ 0.99) and after (p ≤ 0.99) acid immersion and ZR-LS after acid immersion (p ≤ 0.99).ConclusionsGastric acid challenge affects the surface properties of lithium disilicate–reinforced glass–ceramic and zirconia-reinforced lithium silicate glass–ceramic. Glazing layer provides lower surface roughness, and the glazed surface tends to smoothen after the gastric acid challenge.Clinical relevanceSurface finish of lithium disilicate–reinforced glass–ceramic and zirconia-reinforced lithium silicate glass–ceramic has a clear impact on material’s surface properties. Gastric acidic challenge changes surface properties but glazing seems to function as a protective barrier. Nevertheless, also glazing tends to smoothen after heavy gastric acid challenge. Glazing can be highly recommended to all glass–ceramic restorations but especially in patients with gastroesophageal reflux disease (GERD) and eating disorders like bulimia nervosa.

Comparison of the Effect of the Same Polishing Method on the Surface Roughness of Conventional, CAD/CAM Milling and 3D Printing Denture Base Materials

Objective: The aim of this study was to evaluate the effect of both the same polishing method and those with and without thermal aging on the surface roughness of conventional, CAD/CAM milling and 3D printing denture base materials.&#x0D; Materials and Methods: A total of 30 round shaped specimens were obtained by 3 different methods (n=10): Conventional, CAD/CAM milling and 3D-Printing. After applying the same polishing technique to all groups, surface roughness values were measured. Profilometer device was used for surface roughness measurement. Then, after the thermal aging of all samples, surface roughness values were measured and the roughness values between no-thermocycling and thermocycling were compared. Tukey, Mann Whitney U and Kruskal Wallis tests were used statistically. P values of ≤ 0.05 were considered significant. &#x0D; Results: As a result of the same polishing process, there was a difference in surface roughness in all groups. While the highest surface roughness values were seen in 3D-printing, the lowest roughness value was seen in the CAD/CAM milling and was statistically significant (p&amp;lt;0.05). Thermocycling did not show a statistically significant difference in surface roughness (p&amp;gt;0.05).&#x0D; Conclusions: The same polishing process caused different surface roughness values in the denture base materials obtained with different methods, and the lowest surface roughness value was seen in the CAD/CAM milling.

Mechanical and Plasma Electrolytic Polishing of Dental Alloys.

(1) Background: In dentistry, a reduction in surface roughness is established mostly by conventional mechanical polishing to hinder biofilm adhesion. This is time- and labor-intensive. Plasma electrolytic polishing is believed to be an effective finishing method due to the reduced treatment time and materials used for applications in dentistry. (2) Methods: Co-Cr-Mo dental alloy samples were sandblasted and prepared with either plasma electrolytic or conventional mechanical polishing. Evaluation of the polishing methods was obtained by atomic force microscopy, scanning electron microscopy and energy-dispersive X-ray spectroscopy. (3) Results: The sandblasted samples showed the highest surface roughness (Heraenium® Sun 991 ± 288 nm; Wironit® 1187 ± 331 nm). Our results show that with plasma electrolytic polishing, Co-Cr-Mo surfaces can be polished with a surface roughness in the nanometer range, comparable to those achieved by conventional mechanical polishing. Conventional mechanical polishing (Heraenium® Sun 134 ± 23 nm; Wironit® 114 ± 11 nm) provided lower surface roughness values compared to plasma electrolytic polishing (Heraenium® Sun 288 ± 94 nm; Wironit® 261 ± 49 nm). We anticipate our pilot study as a starting point for future studies to refine process parameters and quantitative microbiological assays. (4) Conclusions: Plasma electrolytic polishing might have a promising future for polishing dental alloys.

Analisis Pengaruh Variasi Kecepatan Spindel Dan Feeding Terhadap Nilai Kekasaran Permukaan Proses Finishing Bubut CNC

In the industrial sector, technological progress has experienced very rapid development. So that the manufacturing industry is required to be able to produce quality products and a high level of accuracy with fast processing. One machine that can meet these demands is a CNC lathe, where a CNC lathe is a machine that is controlled using a computer system in its operation. In the machining process of CNC lathes, the level of surface roughness of the machining material is of great concern, because the lower the surface roughness value, the better the quality of the product. Therefore, the aim of this study was to obtain a low surface roughness value using a finishing cutting edge. The material used is AISI 1045 steel which is turned using a MORI SEIKI SL-25 CNC machine. The parameters used are spindle speed and feeding. The research method used was the Taguchi method with an orthogonal matrix L9(32) experimental design and 3 replications were carried out to reduce large deviations. The result of this research is to obtain a combination of parameters that produce minimum surface roughness values, namely spindle speed of 1804 rpm and feeding of 0.1 mm/put. And the parameter that has the greatest effect on the value of roughness is feeding with a difference of 16.029 and the one that has the least effect on the value of surface roughness is spindle speed with a difference of 1.384.

Effect of an In-Office Bleaching Agent with Surface Pre-Reacted Glass-Ionomer Filler on the Enamel Surface: A In-Vitro Study.

In-office bleaching with high concentrations of hydrogen peroxide (H2O2) agents causes undesirable alterations in the enamel. Surface pre-reacted glass-ionomer (S-PRG) filler is a functional material known for its acid-neutralizing and demineralization-inhibition properties. This study evaluates the effect of S-PRG filler incorporation in H2O2-based bleaching on the enamel surface. Bovine enamel surfaces were bleached using a bleaching paste formulated with a liquid (35% H2O2) and a powder containing 5% or 10% S-PRG filler. The surface roughness and the Vickers microhardness of the treated enamel surfaces were evaluated. The enamel surfaces were observed under a scanning electron microscope (SEM) and analyzed using energy dispersive X-ray (EDX) technology. The surfaces were challenged by citric acid and observed by SEM. The specimens bleached with the paste containing the S-PRG filler showed lower enamel surface roughness and higher microhardness values than did those bleached with the plain paste (0% S-PRG filler); meanwhile, there were no significant differences between the 5% or 10% S-PRG filler groups. The S-PRG filler groups showed enamel surface morphologies similar to those of the non-bleached enamel, according to SEM observation, and EDX analysis detected the presence of fluoride and strontium ions. The S-PRG filler groups showed a higher resistance to erosion. The S-PRG filler mitigated the detrimental effects of bleaching agents on the enamel surface and provided resistance to erosion.

Determination of Surface Roughness of the Land Texture Using Remote Sensing Data and Geo-Informatic Techniques: A Case Study in Kurdistan Region-Iraq

Surface roughness (SR) is a significant geomorphic factor that has been effectively applied to determine material characteristics, present and past processes, and the period passed by since development in the environmental and earth sciences. Thus, this type of study is essential for analyzing SR and its importance. The research efforts to display a coherent evaluation of techniques and remote sensing data. The digital elevation models (DEMs) data were taken into account for quantifying the SR of landscape in different scales in selected areas that belong to the Kurdistan region, north of Iraq. The various types of DEMs {ALOS PALSAR (12.5 m) and SRTM in (30 m) and (90 m) resolution} as remotely sensed data integrated with GIS techniques were used to calculate SR regarding different neighborhood sizes {51 × 51 and 100 × 100 cells moving window size (MWZ)} in the both selected areas. The first study area is a mountainous terrain characterized by a number of anticlines and synclines that are located in High Folded Zones (HFZ), while the second study area is virtually a plain that is located in Low Folded Zones (LFZ). It found that SR calculation in wide and mountainous areas can be efficiently analyzed in more detail by using coarse-resolution DEMs from large MWZ, such as 100 × 100 cells, whereas high-resolution DEMs can be considered for studying SR in small, urban, and plain areas to reach detail information regarding smaller MWZ. The results show that the E and W segments of Safeen and the western segment of Shakrok anticlines have the highest SR values, which indicate high incision at elevated and extremely eroded parts of area one, although Bani Bawi, Pirmam, and Khatibian anticlines have moderate to low SR values due poorly incised. On the other hand, the areas within LFZ are mainly flat and have the lowest values of SR, which indicate a very poorly dissected landscape except for the northwest part of the area two relatively has a higher SR value.