Low Concentrations Of Heavy Metals Research Articles

Ionic liquid catalyzed low-temperature hydrothermal carbonization of sewage sludge to produce hydrochar with low heavy metal content and positive energy recovery

An ionic liquid (IL, [DMAPA]HSO4) was prepared to facilitate the removal of heavy metals by hydrothermal carbonization (HTC) in sewage sludge (SS) and to obtain a positive energy recovery (ER, (Energyoutput/Energyinput − 1) > 0). The results found that the removal efficiencies of the Fe, Mn, Zn, Co, and Cd from SS exceeded 75 % with positive ER (6 %) at 20 wt% IL dosage (IL:SS). IL promoted the HTC reactions of proteins and polysaccharides to produce fixed carbon and small molecule polymers. The process mainly relies on IL to catalyze the dehydration and graphitization of SS and to destroy the heavy metal binding sites such as carboxyl and hydroxyl groups. Additionally, IL aids in constructing the macropore structures in hydrochar, thereby facilitating the release of heavy metals and water during the HTC process. This discovery holds promise for removing heavy metals from SS by one-pot HTC processes with positive energy recovery.

Temporal and spatial evolution of different heavy metal fractions and correlation with environmental factors after prolonged acid mine drainage irrigation: A column experiment

Acid mine drainage (AMD) has global significance due to its low pH and elevated heavy metal content, which have received widespread attention. After AMD irrigation in mining areas, heavy metals are distributed among soil layers, but the influencing factors and mechanisms remain unclear. AMD contamination of surrounding soil is primarily attributed to surface runoff and irrigation and causes significant environmental degradation. A laboratory soil column experiment was conducted to investigate the temporal and spatial distribution of the heavy metals Cd and Cu, as well as the impact of key environmental factors on the migration and transformation of these heavy metals following long-term soil pollution by AMD. After AMD addition, the soil exhibited a significant increase in acidity, accompanied by notable alterations in various environmental parameters, including soil pH, Eh, Fe(II) content, and iron oxide content. Over time, Cd and Cu in the soil mainly existed in the exchangeable and carbonate-bound fractions. In spatial terms, exchangeable Cu increased with increasing depth. Pearson correlation analysis indicated significant negative correlations between pH and Cu, Cd, and Eh in pore water, as well as negative correlations between pH and the exchangeable fraction of Cd (F1), carbonate-bound fraction of Cd (F2), and exchangeable fraction of Cu (F1) in the solid phase. Additionally, a positive correlation was observed between pH and the residual fraction of Cu (F5). Furthermore, the soil total Cd content exhibited a positive correlation with pyrophosphate-Fe (Fep) and dithionite-Fe (Fed), while CdF1, CdF2, total Cu, and CuF1 displayed positive correlations with Fep. Our findings indicate that the presence of AMD in soil leads to alterations in the chemical fractions of Cd and Cu, resulting in enhanced bioavailability. These results offer valuable insights for developing effective remediation strategies for soils near mining sites.

Evaluating hydrothermal liquefaction hydrochar from sewage sludge as a phosphorus resource through struvite production

Hydrothermal liquefaction (HTL) has attracted considerable attention for valorizing sewage sludge to biofuels while the solid residue, hydrochar, has received little attention for its final application. In the current work hydrochar recovered from hot separation in a pilot-scale HTL plant is evaluated for its nutrient value, in particular as a sustainable Phosphorus (P) resource. Following thorough characterization of the hydrochar, P recovery as struvite (NH4MgPO4·6H2O) is investigated to produce a fertilizer with a lower heavy metal content that could be used in current agricultural practices. P extraction using inorganic (hydrochloric and sulphuric) and organic (citric) acids is evaluated by applying 0.1–1 mol/L of acids for 1–12 h with a liquid/solid ratio of 10 mL/g. A second-order polynomial model was established by response surface methodology (RSM) to predict the P extraction with different acids. The optimum operating conditions for maximum P extraction (94 %) are suggested as 0.7 M of acid strength (H2SO4) and 6.5 h of extraction time. Addition of citric acid (CA) during the struvite precipitation from acid-leached P solution was found to improve the struvite purity from 36.6 % to 54 % with a reduction in heavy metal content. Furthermore, morphological analysis validated the formation of struvite. Upon comparison with the regulations, hydrochar was found to exceed some of the heavy metal limits but was low in polyaromatic hydrocarbons (PAHs), per- and polyfluorinated substances (PFAS) and showed low toxicity to Aliivibrio fischeri. P extraction and struvite precipitation are shown to reduce heavy metal contents below regulatory limits with P recoveries from 40 % to 67 %. Thus, as an alternative to direct land application of hydrochar, harvested struvite from hydrochar could be applied as a fertilizer with no apparent environmental risk.

Microbial Application in Heavy Metal Removal from Pharmacological Industrial Effluent

In industrial effluents, significant amounts of metallic cations such as zinc, copper, iron, manganese, lead, nickel, and cadmium are present. Long-term irrigation with these effluents increases the amount of organic carbon and heavy metals in the soil, increasing the likelihood that they will enter the food chain and, eventually, result in significant bioaccumulation. Many techniques for the treatment and disposal of metal-containing wastes, such as ion exchange, reverse osmosis, in flotation, and evaporation, have been developed in order to reduce metal pollution issues. The main disadvantages of conventional treatments are low efficiency at low concentrations of heavy metals, expensive handling, and safe disposal of toxic sludge. In light of this, an effort has been made to investigate how tannery affects the growth of green gram.

Investigating the potential of mineral precipitation in co-pyrolysis biochar: Development of a novel Cd (II) adsorption material utilizing dual solid waste

Ionic cadmium (Cd (II)) in water is a significant threat to ecosystems, the environment, and human health. Research is currently focused on developing efficient adsorption materials to combat Cd (II) pollution in water. One promising solution involves co-pyrolyzing solid residue from anaerobic digestion of food waste with oil-based drill cuttings pyrolysis residue to create a biochar with high organic matter content. This biochar has a lower heavy metal content and leaching toxicity compared to China's national standards, making it both safe and resourceful. It exhibits a high adsorption capacity for Cd (II) in water, reaching up to 47.80 ± 0.37 mg/g. Raising the pyrolysis temperature above 600 °C and increasing the amount of pyrolysis residue beyond 30 % enhances the biochar's adsorption capacity. The adsorption process is primarily driven by mineral precipitation, offering a promising approach for dual waste resource management and reducing heavy metal pollution.

Treatment of electroplating wastewater using electrocoagulation and integrated membrane.

Electroplating wastewater contains heavy metal ions and organic matter. These contaminants not only endanger the environment but also pose risks to human health. Despite the development of various treatment processes such as chemical precipitation MBR, electrocoagulation (EC) ceramic membrane (CM), coagulation ultrafiltration (UF) reverse osmosis (RO), and CM RO. These methods are only effective for low concentrations of heavy metals and struggle with high concentrations. To address the challenge of treating electroplating wastewater with high heavy metal content, this study focuses on the wastewater from Dongfang Aviation Machinery Processing Plant. It introduces an EC and integrated membrane (IM) treatment process for electroplating wastewater. The IM comprises microfiltration (MF) membrane, nanofiltration (NF) membrane, and RO membrane. Results indicated that under specific conditions, such as a pH of 8, current density of 5 A/dm2, electrode plate spacing of 2 cm, 35 min of electrolysis time, and influent pH of 10 for the IM, removal rates of Zn2+, Cu2+, Ni2+, and TCr in the wastewater exceeded 99%. The removal rates of chemical oxygen demand (COD), suspended solids (SS), total phosphorus (TP), total nitrogen (TN), and petroleum in wastewater exceed 97%. Following a continuous cleaning process, the membrane flux can consistently recover to over 94.3%.

Exploring the influence of ground-dwelling ant bioturbation activity on physico-chemical, biological properties and heavy metal pollution in coal mine spoil

Coal mining activities increase the soil concentrations of heavy metals manifold thus impacting soil health and biodiversity. The understanding of the impact of bioturbation activities by ant colonies on soil in coal mine spoil site across different restoration ages is not studied. The study aimed to investigate the influence of bioturbation activities by two most common and distinct coal mine site inhabiting ant species (C. compressus and C. longipedem) at six different ages (2, 4, 6, 8, 10 and 12 years old) on the soil heavy metal concentrations of Fe, Zn, Mn, Cu, Ni, Pb, Cd and Cr, pH, OM, TC, TN, soil enzyme activity of DH, ACP, β-glucosidase and proteases properties of soil. Soil samples were collected from opencast coalmine spoils during October and November 2017. Reference (Ref.) soil samples (n=10 per site) were collected (from area adjacent to ant nest colony approximately 2–5 m distance) from a depth of 0–15 cm and ant nest debris soil of each ant species (n=10 per site) were collected from each site. Heavy metal pollution decreased and pH, OM, TC, TN and soil enzyme activity of DH, ACP, β-glucosidase and proteases of soil in both Ref. soil and ant nest debris soil increases with the increase of mine site restoration age. Our study revealed that different age of the mine spoil have more profound effects on the soil quality and heavy metal content. Contrary to our hypothesis, regression analysis did not support our notion that ant bioturbation activity directly accelerate heavy metal breakdown. Instead, our findings suggests that ant colonies prefer to construct their nest for the locations with lower heavy metal concentrations and higher enzyme activity and increase in soil porosity is a key factor behind the low heavy metal concentration in the nest debris soil.

Black soldier fly-based bioconversion of biosolids: Microbial community dynamics and fate of antibiotic resistance genes

Biosolids as by-products of wastewater treatment can contain a large spectrum of pathogens and antibiotic resistance genes (ARGs). Insect-based bioconversion using black soldier fly larvae (BSFL) is an emerging technology that has shown to reduce significant amounts of biosolids quickly and produce larvae biomass containing low heavy metal concentrations. However, to the best of our knowledge, this is the first study investigating the transfer of pathogens and ARGs from biosolids into the process' end-products, BSFL and frass. We hypothesized that BSF-based bioconversion can decrease the abundance of pathogenic bacteria and ARGs in biosolids. In this study, we performed BSFL feeding trials with biosolids blended or not blended with wheat bran, and wheat bran alone as a low bioburden diet (control). We conducted 16S rRNA amplicon sequencing to monitor changes of the BSFL-associated microbial community and the fate of biosolids-associated pathogens. A diverse set of ARGs (ermB, intl1, sul1, tetA, tetQ, tetW, and blaCTX-M-32) were quantified by qPCR and were linked to changes in substrate- and BSFL-associated microbiomes. BSF-based bioconversion of biosolids-containing substrates led to a significant reduction of the microbial diversity, the abundance of several pathogenic bacteria and the investigated ARGs (< 99 %). Feeding with a high bioburden biosolid diet resulted in a higher microbial diversity, and the accumulation of pathogenic bacteria and ARGs in the BSFL. Results of this study demonstrated that BSF-based bioconversion can be a suitable waste management technology to (1) reduce significant amounts of biosolids and (2) reduce the presence of pathogens and ARGs. However, the resulting larvae biomass would need to undergo further post-treatment to reduce the pathogenic load to allow them as animal feed.

Photoelectrocatalytic Reduction of Cr(VI) in Wastewater with a CuBi2O4 Thin Film Photocathode

Photoelectrocatalytic approaches show promise for contaminate removal in wastewater through redox reactions. However, the direct treatment of very low concentration heavy metals is a challenging task. Copper bismuth oxide is considered as a potential photocathode material due to its appropriate bandgap width and excellent light absorption properties. In this work, we utilize copper bismuth oxide photoelectrodes with micrometer-scale pores to achieve the efficient and complete reduction of micromolar-level hexavalent chromium(VI) in wastewater. In a continuous 180 min experiment, the reduction rate of 5 µM hexavalent chromium reached 97%, which is an order lower than the drinking standard. Such a process was facilitated by the unique hierarchical microstructure of the oxide thin film and the porous morphology. On the other hand, the structural evolution during the operation was analyzed. A surface passivation was observed, suggesting the possible long-term practical application of this material. This study serves as an important reference for the application of photoelectrocatalysis in addressing Cr(VI) pollution in wastewater, with implications for improving water quality and environmental protection.

Evaluation of Hospital Wastewater Treatment Using Sewage Treatment Plant for Heavy Metals, Radionuclides, and Some Pharmaceuticals: A Case Study

This is the first study in Oman to evaluate the efficiency of a sewage treatment plant (STP) for hospital wastewater (HWW) treatment for heavy metals, radionuclides, and some selected pharmaceuticals. A sewage treatment plant (STP) at Sultan Qaboos University (SQU) receives HWW, from Sultan Qaboos University Hospital (SQUH), and municipal wastewater from non-medical facilities at SQU. Representative samples of HWW (before mixing with municipal wastewater at STP), STP-treated wastewater (TWW), and STP mixing sludge, were collected and analyzed. A method for analyzing pharmaceuticals including metformin, atenolol, chlorpheniramine, triprolidine, diphenhydramine, and citalopram was developed and validated using LC-MS-MS. HWW and TWW show low concentrations of heavy metals. Radionuclides found in HWW include Cs137, K40, Ra226, Th234, I131, Tl208, Zn65 Ac228, Sb125, Bi124 and Be7. Diphenhydramine (2.24 mg/L), chlorpheniramine (0.293 mg/L) and atenolol (0.0260 mg/L) were found in HWW. Heavy metals, radionuclides, and pharmaceuticals were found less in TWW than in HWW. STP sewage sludge showed higher levels of these pollutants than HWW or TWW. Concentrations of diphenhydramine, chlorpheniramine, and citalopram were 137, 0.950, and 169 mg/kg, respectively in dried sewage sludge. The study confirms the ineffectiveness of STP treatment to completely remediate HWW. HWW should be considered hazardous and requires physico-chemical treatment before mixing with municipal wastewater. Keywords: Hospital, pharmaceuticals, radionuclides, heavy metals, wastewater.

Systematic Characterization of Cow Manure Biochar and Its Effect on Salicornia herbacea L. Growth

This study investigated the potential of biochar as a sustainable material for waste utilization and carbon sequestration in soil. Biochar was prepared from cow manure (CM) and applied to the soil. Biochar was processed by subjecting CM to various temperature ranges (400 [CMB400], 550 [CMB550], and 700 °C [CMB700]) under nitrogen gas (allowed to flow to restrict oxygen), with residence time set to 3 h. The characteristics of the biochar produced at each temperature were analyzed. The experiment was conducted for approximately 15 weeks with the laboratory temperature maintained between 24 and 26 °C. The growth rate of plants was obtained by measuring their length weekly, starting 4 weeks after crop establishment. CMB550 exhibited the highest specific surface area (117.57 m2 g−1) and well-distributed pore size; therefore, it was mixed with the soil at a specific ratio and put in pots for the planting of Salicornia herbacea L. (glasswort) in the laboratory. The results demonstrated that adding biochar to soil increased plant growth and that the biochar could store organic carbon. In addition, an investigation of heavy metals demonstrated that samples with biochar had lower heavy metal concentrations in glasswort than those without because of the potential of biochar to adsorb heavy metals. By interacting with heavy metal ions in soil solution, the reactive sites and functional groups on the surface of biochar immobilize them and lessen their potentially detrimental effects on plant growth. Overall, biochar has the potential to be a valuable resource for waste management and environmental improvement.

A Study on the Valorization of Rice Straw into Different Value-Added Products and Biofuels

This work depicts that rice straw (RS), which is one of the major lignocellulosic wastes all over the world and causing many environmental problems, has considerable amounts of protein, ash, macronutrients, and micronutrients of approximately 11.38%, 16.77%, 2.27 mg/kg, and 771.9 mg/kg, respectively; besides, a C/N ratio of 15.18, a total N, P2O5, and K2O content of 1.85%, and a considerably low concentration of undesirable heavy metals and silica of approximately 77.69 mg/kg and 109 mg/kg are also present, which recommends its applicability as a precursor feedstock for the production of organic fertilizer and animal fodder. The batch solid-state fermentation (SSF) of RS by Trichoderma longibrachiatum DSMZ 16517 produced considerable amount of total reducing sugars (TRS) of approximately 339.2 mg TRS/g RS under the optimum operatic conditions of 20% (w:v) substrate concentration, pH 7, 1% inoculum size, a 9-day incubation period, and 30°C incubation temperature. The readily available and cost-effective agroindustrial waste, sugarcane molasses, proved to enhance the fungal biomass growth and (hemi) cellulolytic enzymes activities. The inoculated RS-SSF batch process with T. longibrachiatum precultured on 10% molasses enhanced the (hemi) cellulolytic enzymatic activities and TRS production rate by approximately 5.82 and 3.8 folds, respectively, relative to that inoculated by T. longibrachiatum precultured in the conventional potato dextrose broth medium. The separate hydrolysis and fermentation processes by different yeast strains Candida tropicalis DSM 70156, C. shehatae ATCC 58779, and Saccharomyces cerevisiae ATCC 64712 revealed an efficient bioethanol yield and productivity that ranged between 0.36 and 0.38 g/g sugars and 0.22 and 0.23 g/L/h, respectively, with concomitant competent fermentation efficiencies that ranged between 48.35% and 51.25%. The proximate analysis of rice straw before and after fungal hydrolysis proved calorific values of approximately 15.8 MJ/kg and 16.05 MJ/kg, respectively, recommending their applicability as primary and secondary solid biofuels. Thus, this study proved the waste prosperity of RS for environmental opulence and sustainability.

Properties of substitute motor fuels produced from ethanol in biorefineries

The article presents the definition of bioindustry, in particular biorefinery. The technology for obtaining synthetic fuel EtG (Ethanol to Gasoline) in a plant using bioethanol from food waste was presented. The physicochemical properties of EtG fuel were presented. EtG fuel stands out due to its limited content of benzene and sulfur and a low content of mechanical impurities and heavy metals. EtG fuel can be considered a replacement fuel for motor gasoline. The results of exhaust emissions tests from vehicles with spark-ignition engines in the WLTC test on a hot and cold engine were presented. It was found that EtG fuel is characterized by lower specific distance emissions of CO, NOx and CH4 and slightly higher specific distance emissions of NMHC when starting a cold engine compared to gasoline, while the specific distance emission of CO2 for both fuels were very similar.

Ecological risk assessment of heavy metals in desulfurized seawater discharged from a coal-fired power plant in Qingdao.

Despite the prevalence of discharge of large volumes of heavy-metal-bearing seawater from coal-fired power plants into adjacent seas, studies on the associated ecological risks remain limited. This study continuously monitored concentrations of seven heavy metals (i.e. As, Cd, Cr, Cu, Hg, Pb, and Zn) in surface seawater near the outfall of a coal-fired power plant in Qingdao, China over three years. The results showed average concentrations of As, Cd, Cr, Cu, Hg, Pb, and Zn of 2.63, 0.33, 2.97, 4.63, 0.008, 0.85, and 25.00 μg/L, respectively. Given the lack of data on metal toxicity to local species, this study investigated species composition and biomass near discharge outfalls and constructed species sensitivity distribution (SSD) curves with biological flora characteristics. Hazardous concentrations for 5% of species (HC5) for As, Cd, Cr, Cu, Hg, Pb, and Zn derived from SSDs constructed from chronic toxicity data for native species were 3.23, 2.22, 0.06, 2.83, 0.66, 4.70, and 11.07 μg/L, respectively. This study further assessed ecological risk of heavy metals by applying the Hazard Quotient (HQ) and Joint Probability Curve (JPC) based on long-term heavy metal exposure data and chronic toxicity data for local species. The results revealed acceptable levels of ecological risk for As, Cd, Hg, and Pb, but unacceptable levels for Cr, Cu, and Zn. The order of studied heavy metals in terms of ecological risk was Cr > Cu ≈ Zn > As > Cd ≈ Pb > Hg. The results of this study can guide the assessment of ecological risk at heavy metal contaminated sites characterized by relatively low heavy metal concentrations and high discharge volumes, such as receiving waters of coal-fired power plant effluents.

Changes in properties of reclaimed-mine soil, plant growth, and metal accumulation in plants with application of coal fly ash and empty fruit bunches of oil palm

Reclaimed-mining soil (RMS) is characterized by low fertility, acidic pH, and high heavy metal contents. As a result, adding amendments becomes essential to support plant growth. Therefore, this research measured alterations in the characteristics of RMS, plant growth, and metal accumulation in plants with the co-application of coal fly ash (CFA) and empty fruit bunches of oil palm (EFBOP). In the first experiment, various levels of CFA (0, 75, and 150 Mg ha-1) and EFBOP (0, 25, and 50 Mg ha-1) were added to the RMS and then incubated at 70% water holding capacity for 45 days to determine their effect on changes in soil properties. In the second experiment, four treatments: control, CFA, EFBOP, and CFA+EFBOP were tested in the greenhouse to quantify their effects on the growth and metal accumulation of plants. Results of the study showed that the co-application of CFA and EFBOP significantly affected bulk density, pH, mineral nitrogen (NH4+ and NO3-), available phosphorus, and exchangeable Ca and Mg in RMS. CFA application increased exchangeable Al by 82-160%, while EFBOP resulted in a decrease of 24-119%. CEC decreased with CFA application and increased with the use of EFBOP. Plant growth increased with the co-application of CFA and EFBOP. The addition of CFA to soils results in increasing metal contents in plant tissue; however, the presence of EFBOP reduced the concentrations of metal in plant tissue. These results highlight the potential of CFA and EFBOP, which are industrial and agricultural wastes, as valuable soil amendments.

Оценка потенциального риска хлоридов и их влияние на всхожесть семян и развитие проростков растений

The article discusses the negative effect of de-icing materials (DM) and salts in their composition on plant seedlings germination and development. The influence of sodium and potassium cations and chlorine anion on phytotoxicity index is considered. The dynamics of test-plants (Avena sativa L., Raphanus sativa L., Hordeum vulgare L.) response on a number of test-indicators depending on the concentration of basic salts in DM by a promising method of phytotesting was analyzed. The analyzed DMs in concentrations higher than 1% have an inhibitory effect. The DM at 14–16 g/L suppresses root length of test plants (more than 50%) relative to the control. The low content of heavy metals, such as Cd, Cu, Pb, in the analyzed DM samples indicates the toxicity of sodium chloride as an active de-icing agent. The results of statistical analysis convincingly prove the high phytotoxicity of sodium chloride (NaCl) in relation to such indicators of the juvenile test-plant development as germination, the primary root length and the coleoptile height. Increasing the NaCl concentration in the solution from 0.75 to 1% was strongly toxic to the test-plants (more than 50%). Potassium chloride (KCl) in the concentration range of 0.1–1.0% showed no phytotoxicity. The KCl presence in the NaCl-included de-icing reagent reduces its phytotoxicity and allows the toxicity level of the agent to be assessed as “moderately toxic”.

The incidence of upper respiratory infections in children is related to the concentration of vanadium in indoor dust aggregates.

It has been reported that the disease-initiated and disease-mediated effects of aerosol pollutants can be related to concentration, site of deposition, duration of exposure, as well as the specific chemical composition of pollutants. To investigate the microelemental composition of dust aggregates in primary schools of Vilnius and determine trace elements related to acute upper respiratory infections among 6-to 11-year-old children. Microelemental analysis of aerosol pollution was performed using dust samples collected in the classrooms of 11 primary schools in Vilnius from 2016 to 2020. Sites included areas of its natural accumulation behind the radiator heaters and from the surface of high cupboards. The concentrations of heavy metals (Pb, W, Sb, Sn, Zr, Zn, Cu, Ni, Mn, Cr, V, and As) in dust samples were analyzed using a SPECTRO XEPOS spectrometer. The annual incidence rates of respiratory diseases in children of each school were calculated based on data from medical records. The mean annual incidence of physician-diagnosed acute upper respiratory infections (J00-J06 according to ICD-10A) among younger school-age children was between 25.1 and 71.3% per school. A significant correlation was found between vanadium concentration and the number of episodes of acute upper respiratory infections during each study year from 2016 to 2020. The lowest was r = 0.67 (p = 0.024), and the highest was r = 0.82 (p = 0.002). The concentration of vanadium in the samples of dust aggregates varied from 12.7 to 52.1 parts per million (ppm). No significant correlations between the other trace elements and the incidence of upper respiratory infections were found, which could be caused by a small number of study schools and relatively low concentrations of other heavy metals found in the samples of indoor dust aggregates. A significant and replicable correlation was found between the concentration of vanadium in the samples of natural dust aggregates collected in primary schools and the incidence of acute upper respiratory infections in children. Monitoring the concentration of heavy metals in the indoor environment can be an important instrument for the prevention and control of respiratory morbidity in children.

Adsorption and enrichment of low-concentration heavy metal complexes by retractable claws made of polyelectrolyte brushes

The removal of heavy metal complexes from water at low concentrations poses a difficult challenge as the cost of chemical or energy input is often disproportional to the benefits gained. Herein, we propose a novel strategy by employing polyelectrolyte brushes as the “retractable claws” for adsorption and enrichment of heavy metal complexes. The polyelectrolyte brush constructed by grafting poly[2-(methacryloyloxy)ethyl trimethylammonium chloride] on the reduced graphene oxide (rGO-PMTC), exhibits a high adsorption capacity of 4.80 mg g−1 for 4.96 mg L−1 of Cu-ethylenediaminetetraacetic acid (Cu-EDTA), which is nearly 30 times larger than that of parent graphene oxide. Moreover, a very rapid adsorption rate can be achieved as 7.17 g mg−1 min−1, which is up to 3 orders of magnitude higher than many reported adsorbents. Molecular dynamics simulations reveal that during the adsorption process, the flexible polyelectrolyte brushes are fully extended to form the “claws” for quickly capturing Cu-EDTA complexes by strong electrostatic attraction. Subsequently, the polyelectrolyte brushes shrink with Cu-EDTA-mediated bridging and wrap the heavy metal complexes inside. In addition, the adsorbed Cu-EDTA complexes can be completely released from the polyelectrolyte brushes by simply introducing sodium chloride, resulting in an almost 20-fold enrichment of metal concentration for recycling. After ten adsorption–desorption cycles, the polyelectrolyte brushes only have 10 % reduction in the adsorption efficiency. The novel adsorbent can be extended to the effective removal of other heavy metal complexes with a low concentration and real electroplating wastewater.

Efficient removal of heavy metals in water utilizing facile cross-link conjugated linoleic acid micelles.

Micellar-enhanced ultrafiltration (MEUF) technology is an effective method to treat low-concentration heavy metal wastewater. However, the leakage of surfactants in the ultrafiltration (UF) process will inevitably cause secondary pollution. In this study, a biosurfactant of conjugated linoleic acid (CLA) with conjugated double bonds was selected to bind its micelles by simple thermal crosslinking to obtain morphologically stable stearic acid (SA) nanoparticles. The pure SA nanoparticles were obtained by repeated dialysis. The stability of the SA nanoparticles was verified by comparing the particle size distribution and solubility of the materials before and after crosslinking at different pH levels. The effectiveness of SA nanoparticle-enhanced UF in removing heavy metals was verified by exploring the adsorption performance of SA nanoparticles. The dialysis device was used to simplify the UF device, wherein SA nanoparticles were assessed as adsorbents for the elimination of Cu2+, Pb2+, and Cd2+ ions from aqueous solutions under diverse process parameters, including pH, contact time, metal ion concentration, and coexisting ions. The findings indicate that the SA nanoparticles have no evidence of secondary contamination in UF and exhibit compatibility with a broad pH range and coexisting ions. The maximum adsorption capacities for Cu2+, Pb2+, and Cd2+ were determined to be 152.77, 403.56, and 271.46 mg/g, respectively.

The effect of oil pollution on community structure of benthic macro ‎invertebrates in the northwest of the Persian Gulf ‎ ‎(Case study: Jafari creek)‎

&lt;p&gt;This study evaluates the contamination levels of heavy metals and petroleum hydrocarbons in Jafari ‎Creek sediments and the effect of these pollutions on Macrobenthos in 2017. Studies to understand ‎the effect of heavy metal Cadmium, Chromium, Nickel, Lead, Selenium, Zinc, Copper, and ‎Vanadium, and 16 hydrocarbon compounds, organic material, and soil texture on the population of ‎Jafari Creek Macrobenthos in five stations along the estuary and analyzed using standard ‎procedures. The 4 identified Macrobenthos included Bivalvia with 9 species, Gastropoda with 8 ‎species, Crustacea with 7 species, and Polychaeta with 6 species totaling Macrobenthos 3645.14 per ‎square meter. The dominant class was Polychaetes (53.9%), followed by Bivalvia (23.2%), ‎Gastropoda (9.93%), and Crustaceans (15.8%), with slightly different (P&amp;lt;0.05), were in the second ‎and third class. Among the studied metals, zinc, chromium, and nickel had the highest ‎concentration. Among the hydrocarbons, Anthracene at station 1, Fluorene at station 2, ‎Phenanthrene and Dibenzo [A, H] Anthracene at station 3, and Fluoranthene at station 4 with a ‎concentration between &amp;lt;0.01- 0.091 ppm had the highest value. The highest and lowest heavy metal ‎concentrations were measured at station 4 (215.54 ± 14.58 ppm) and station 1 (102.39 ± 24.15 ‎ppm), respectively. In return, stations 1 (0.339 ± 0.074 ppm) and 4 (0.196 ± 0.078 ppm) had the ‎highest and lowest concentration of hydrocarbons, respectively. Regarding the number of identified ‎Macrobenthos, stations 3 and 2, with 1738.64 and 333.28 n/m2 had the highest and lowest numbers, ‎respectively. The class of Crustacea had a positive correlation with zinc, copper, and lead metal and ‎a negative correlation with Selenium. Polychaeta was positively correlated with cadmium and ‎vanadium. Gastropoda had a negative correlation with vanadium and chromium, a positive ‎correlation with lead and hydrocarbons, and Bivalvia correlated negatively with lead and zinc and ‎had a correlation with vanadium. Considering that the areas around Jafari Creek are an industrial, ‎petrochemical, and economic region considered one of the important catchments in the province of ‎Khuzestan, the sediments, water, and animal tissues must be periodically the analysis of heavy ‎metals and oil hydrocarbons should be considered.‎&lt;/p&gt;&#x0D;