Lower Extracellular Polymeric Substances Research Articles

Impact of feeding regimes on the performance of anaerobic sequencing batch membrane bioreactor treating wastewater from an urban drain

ABSTRACT This work evaluated an anaerobic sequencing batch membrane bioreactor (AnSBR-MBR) equipped with waste-based ceramic membranes for treating low-strength real drain wastewater. Two feeding regimes, viz. settled feed (Phase 1) and mixed feed (Phase 2) were compared. The biological performance (chemical oxygen demand (COD) and phosphate (PO43-) removal) and filtration performance (total suspended solids (TSS) removal and membrane fouling) were investigated. The reactor characteristics in terms of solids content, sludge settling behaviour, and extracellular polymeric substances (EPS) were also assessed. In Phase 1, the settled feed (with the absence of particulate organic matter) resulted in low volatile suspended solids (VSS; 0.23 ± 0.15 g/L), causing low COD removal (28.38 ± 8.14%). In the mixed feed regime in Phase 2, VSS increased (1.82 ± 0.60 g/L) due to the organic content in the particulate matter, which gave microorganisms additional food, resulting in increased COD removal (47.42 ± 2.81%); this phase was also characterised by lower membrane fouling because of the lower EPS content. Marginally higher TSS removal was obtained as well in Phase 2 (96.72 ± 3.26%) than in Phase 1 (90.48 ± 8.14%). This work demonstrates that AnSBR-MBR performance is superior with mixed drain wastewater containing suspended solids and thus pre-settling is not recommended.

Low-biofouling membrane bioreactor: Effects of cis-2-Decenoic acid addition on EPS and biofouling mitigation

Biofouling is inevitable in the membrane process, particularly in membrane bioreactors (MBR) combined with activated sludge processes. Regulating microbial signaling systems with diffusible signal factors such as cis-2-Decenoic acid (CDA) can control biofilm formation without microbial death or growth inhibition. This study assessed the effectiveness of CDA in controlling biofouling in membrane bioreactors (MBRs), essential for wastewater treatment. By modulating microbial signaling, CDA mitigated biofilm formation without hindering microbial growth. Analysis using Confocal Laser Scanning Microscopy (CLSM) revealed structural alterations in the biofilm, reducing biomass and thickness upon CDA application. Moreover, examination of extracellular polymeric substances (EPS) highlighted a decrease in total EPS, particularly effective polysaccharides. In addition, the possibility of shifting from high molecular weight EPS to low molecular weight EPS was revealed through the change in dispersion activity. The 56% extension of MBR operational lifespan resulting from the reduction in EPS is anticipated to offer potential cost savings and improved performance. Despite these results, further investigation is crucial to validate any potential environmental risks associated with CDA and to comprehend its long-term effects at various conditions.

Differentiation and quantification of extracellular polymeric substances from microalgae and bacteria in the mixed culture

Extracellular polymeric substances (EPS) play significant roles in the formation, function, and interactions of microalgal-bacteria consortia. Understanding the key roles of EPS depends on reliable extraction and quantification methods, but differentiating of EPS from microalgae versus bacteria is challenging. In this work, cation exchange resin (CER) and thermal treatments were applied for total EPS extraction from microalgal-bacteria mixed culture (MBMC), flow cytometry combined with SYTOX Green staining was applied to evaluate cell disruption during EPS extraction, and auto-fluorescence-based cell sorting (AFCS) was used to separate microalgae and bacteria in the MBMC. Thermal extraction achieved much higher EPS yield than CER, but higher temperature and longer time reduced cell activity and disrupted the cells. The highest EPS yield with minimal loss of cell activity and cell disruption was achieved using thermal extraction at 55℃ for 30 min, and this protocol gave good results for MBMC with different microalgae:bacteria (M:B) mass ratios. AFCS combined with thermal treatment achieved the most-efficient biomass differentiation and low EPS loss (<4.5 %) for the entire range of M:B ratios. EPS concentrations in bacteria were larger than in microalgae: 42.8 ± 0.4 mg COD/g TSS versus 9.19 ± 0.38 mg COD/g TSS. These findings document sensitive and accurate methods to extract and quantify EPS from microalgal-bacteria aggregates.

Roles of extracellular polymeric substances in arsenic accumulation and detoxification by cell wall intact and mutant strains of Chlamydomonas reinhardtii

Arsenic (As) pollution seriously threatens human and ecological health. Microalgal cell wall and extracellular polymeric substances (EPS) are known to interact with As, but their roles in the As resistance, accumulation and speciation in microalgae remain unclear. Here, we used two strains of Chlamydomonas reinhardtii, namely CC-125 (wild type) and CC-503 (cell wall-deficient mutant), to examine the algal growth, EPS synthesis, As adsorption, absorption and transformation under 10–1000 µg/L As(III) and As(V) treatments for 96 h. In both strains, the As absorption increased after the EPS removal, but the growth, As adsorption, and transformation of C. reinhardtii declined. The CC-125 strain was more tolerant to As stress and more efficient in EPS production, As accumulation, and redox transformation than CC-503, irrespective of EPS presence or absence. Three-dimension excitation-emission matrix (3D-EEM) and attenuated total reflectance infrared spectroscopy (ATR-IR) analyses showed that As was bound with functional groups in the EPS and cell wall, such as -COOH, NH and -OH in proteins, polysaccharides and amino acids. Together, this study demonstrated that EPS and cell wall acted as barriers to lower the As uptake by C. reinhardtii. However, the cell wall mutant strain was more susceptible to As toxicity due to lower EPS induction and higher As absorption.

Extracellular polymeric substances are closely related to land cover, microbial communities, and enzyme activity in tropical soils

Extracellular polymeric substances (EPS) form the main matrix of microbial biofilms and play a crucial role in maintaining microbial life. However, factors influencing EPS concentration and production in soil are poorly understood. Here we show that EPS are closely related to microbial communities and nutrient acquisition in tropical forest and cropland soils with varying iron-aluminum-manganese concentrations and total reserve in base cations. We found under homogenized moisture and temperature conditions that EPS concentration and production efficiency (i.e., EPS per unit of microbial biomass) depend more on land cover than on geochemical soil properties. EPS concentration and production efficiency were higher in cropland than in forest soil and were related to the higher relative abundance of microbial sequences identified as Paenibacillaceae, Ramlibacter, Chaetosphaeria, Burkholderiaceae, and Xanthobacteraceae, pointing to potential EPS producers. In contrast, lower EPS concentration in forest soil was related to the higher relative abundance of microbial sequences associated with e.g., Gemmatimonas and Massilia, suggesting potential EPS degradation. We also found that EPS production efficiency was positively related to microbial investment in nutrient acquisition, implying that EPS production likely follows the same principles as extracellular enzyme activity. That is, EPS production may increase when resources are scarce to facilitate nutrient acquisition, and decrease when resources are abundant. Overall, microbial community composition and resource demand seem to control EPS degradation and accumulation in tropical soils, which could influence microbially-driven carbon and nutrient cycling.

Effect of EPS production on the performance of membrane-based biofilm reactors

This study explored the effect of extracellular polymeric substance (EPS) production on the performance of membrane-based biofilm reactors. Changing EPS production was induced by eliminating one of the main EPS polysaccharides, i.e., Pel. The studies were carried out using a pure culture of either Pseudomonas aeruginosa or an isogenic P. aeruginosa mutant that was unable to produce the Pel polysaccharide. The biofilm cell density for both strains was compared to confirm the Pel deletion mutant decreased overall EPS production in a bioreactor system. When the Pel-deficient mutant was grown as a biofilm, its cell density, i.e., ratio of cells/(cells+EPS), was 74 % higher than the wild type, showing EPS production was reduced by eliminating pel production. The growth kinetics were determined for both strains. The Pel-deficient mutant had a maximum specific growth rate (μ^) that was 14% higher than the wild type. Next, the effects of EPS reduction on reactor performance were assessed for a membrane aerated biofilm reactor (MABR) and a membrane bioreactor (MBR). For the MABR, the organic removal with the Pel-deficient mutant was around 8% higher than for the wild type. For the MBR, the time to reach the fouling threshold was 65 % greater for the Pel-deficient mutant than for the wild type. These results suggest that amount of EPS production can have significant effects on bacterial growth kinetics and bacterial cell density, which in turn can affect the performance of the membrane-based biofilm reactors. In both cases, lower EPS production correlated with more efficient treatment processes.

Effect of outdoor pipe materials and community-intrinsic properties on biofilm formation and chlorine resistance: Black sheep or team leader

Community-intrinsic properties affect the function and composition of microbial community, and understanding of the microbial community-intrinsic properties in different pipe materials of drinking water distribution systems can help to prevent microbial pollution more reasonably and efficiently. This study investigated the biofilm formation and chlorine resistance of multi-species biofilms in two representative outdoor pipe materials (polyethylene (PE) and cast iron pipe). The results showed that cast iron pipes have higher biofilm biomass but lower biofilm activity than PE pipes. The different growth environments of the two pipe materials resulted in diverse microbial community-intrinsic properties and affected multi-species biofilm formation. The microbial communities without Sphingomonas or Acidovorax in cast iron pipe exhibited higher biofilm biomass, when compared with those in PE pipe. In contrast, the microbial community without Bacillus in PE pipe presented higher biofilm biomass, when compared with those in cast iron pipe. Extracellular polymeric substance (EPS) and corrosion products protected bacteria from chlorination. Although community-intrinsic properties helped bacteria resist chlorination, the same microbial community exhibited diverse chlorine resistance in different pipe materials owing to different community-intrinsic properties. While the chlorine resistance of microbial community without Bacillus was low in PE pipe, that in cast iron pipe was better owing to high corrosion degree. Multi-species biofilm without Sphingomonas or Acidovorax presented higher biofilm biomass, but lower EPS content and corrosion products in cast iron pipe, resulting in low chlorine resistance. In summary, this study revealed that outdoor pipe materials could affect microbial community-intrinsic properties, which in turn could influence biofilm characteristics, and provided unique insights for ensuring drinking water safety.

Membrane Fouling Mitigation in MBR via the Feast-Famine Strategy to Enhance PHA Production by Activated Sludge.

Fouling is considered one of the main drawbacks of membrane bioreactor (MBR) technology. Among the main fouling agents, extracellular polymeric substances (EPS) are considered one of the most impactful since they cause the decrease of sludge filterability and decline of membrane flux in the long term. The present study investigated a biological strategy to reduce the membrane-fouling tendency in MBR systems. This consisted of seeding the reactor with activated sludge enriched in microorganisms with polyhydroxyalkanoate (PHA) storage ability and by imposing proper operating conditions to drive the carbon toward intracellular (PHA) rather than extracellular (EPS) accumulation. For that purpose, an MBR lab-scale plant was operated for 175 days, divided into four periods (1–4) according to different food to microorganisms’ ratios (F/M) (0.80 kg COD kg TSS−1 d−1 (Period 1), 0.13 kg COD kg TSS−1 d−1 (Period 2), 0.28 kg COD kg TSS−1 d−1 (Period 3), and 0.38 kg COD kg TSS−1 d−1 (Period 4)). The application of the feast/famine strategy favored the accumulation of intracellular polymers by bacteria. The increase of the PHA accumulation inside the cells corresponded to the decrease of EPS and an F/M of 0.40–0.50 kg COD kg TSS−1 d−1 was found as optimum to maximize the PHA production, while minimizing EPS. The lowest EPS content in the sludge (18% of total suspended solids) that corresponded to the maximum content of PHA (9.3%) was found in Period 4 and determined significant mitigation of the fouling rate, whose value was close to 0.10 × 1011 m−1 h−1. Thus, by imposing proper operating conditions, it was possible to drive the organic matter toward PHA accumulation. Moreover, a lower EPS content corresponded to a decrease in the irreversible fouling mechanism, which would imply a lower frequency of the extraordinary cleaning operations. This study highlighted the possibility of obtaining a double benefit by applying an MBR system in the frame of wastewater valorization: minimizing the fouling tendency of the membrane and recovery precursors of bioplastics from wastewater in line with the circular economy model.

Insight into dead space effects in granular anammox process with organic stress

In this study, the dead space was demonstrated to enhance the robustness of anammox nitrogen (N)-removal under organic stress. Different from the “yellow aggregates” that inhabit in mixing space were assembled by anammox and heterotrophic micro-colonies, the “red granules” that inhabit in dead space were formed by initial anammox aggregates that growing outward with higher anammox-activity, settleability and sludge stability, which endowed the dead space the role of “anammox-stabilizer” with prominent anammox N-removal contribution (63.8%) especially under high organic stress. The extracellular polymeric substances (EPS) dynamic balance test revealed that the high and stable EPS contents in dead space were attributed to the low EPS degradation rate and low proportion of heterotrophic bacteria (HB)-produced EPS, respectively. The weak hydrodynamic forces were the key to less HB-colonization and high granular stability in dead space. Retaining a certain dead space is necessary to prevent anammox bacteria (AnAOB) loss under organic stress.

Nutrient limitation regulates the properties of extracellular electron transfer and hydraulic shear resistance of electroactive biofilm

Understanding the roles of nutrient restriction in extracellular electron transfer (EET) and stability of mixed electroactive biofilm is essential in pollutant degradation and bioenergy production. However, the relevant studies are still limited so far. Herein, the effect of nutrient restriction on the EET pathways and stability of mixed electroactive biofilm was explored. It was found that the electroactive Pseudomonas and Geobacter genera were selectively enriched in the biofilms cultured under total nutrient and P-constrained conditions, and two EET pathways including direct and indirect were found, while Rhodopseudomonas genus was enriched in the N-constrained biofilm, which only had the direct EET pathway. Moreover, multiple analyses including 2D confocal Raman spectra revealed that P-constrained biofilm was rich in extracellular polymeric substances (EPS) especially for polysaccharide, presented a dense and uniform layered distribution, and had better stability than N-constrained biofilm with lower EPS and biofilm with heterostructures cultured under total nutrient conditions.

Ozone and Fenton oxidation affected the bacterial community and opportunistic pathogens in biofilms and effluents from GAC

Granular activated carbon (GAC) filtration impacts pathogen colonization and bacterial communities in drinking water. However, the effects of ozone and heterogeneous Fenton oxidation on microbial community composition, in particular opportunistic pathogens (OPs), and their metabolic potential in biofilms and effluents from GAC filtration are not fully understood. The results of our pilot-scale test indicated that Fenton-GAC filtration removed more dissolved organic carbon (DOC, 1.25 mg/L) than ozone-GAC filtration (0.98 mg/L). Excitation-emission matrix (EEM) results showed that Fenton-GAC removed more tyrosine-like proteins and fulvic acid-like materials, while ozone-GAC removed more humic acid-like compounds and tryptophan-like proteins. Illumina HiSeq analysis indicated that Curvibacter and Hydrogenophaga dominated in the Fenton-GAC biofilm, while Bradyrhizobium, Aquabacterium and Limnobacter were predominant in the ozone-GAC biofilm. Functional prediction suggested that the microbial functional gene related to glyoxylate and dicarboxylate metabolism (the pathway for carbohydrate metabolism) was higher in the Fenton-GAC biofilm, resulting in higher contents of protein in extracellular polymeric substances (EPS) in the Fenton-GAC biofilm. Therefore, there were fewer bacteria that detached from the biofilm into the water during the Fenton-GAC filtration process. The lower EPS content in the effluents from Fenton-GAC resulted in bacteria, including OPs, being easier to remove by chlorine. However, ozone oxidation removed more bacteria, including different OPs, than Fenton oxidation, which contributed to fewer bacteria and OPs in the effluents from ozone-GAC. Overall, our results provide a Fenton-GAC treatment process to remove DOC and control OPs in drinking water systems, the cost of which was comparable to that of ozone-GAC.

Enriched autoinducer-2 (AI-2)-based quorum quenching consortium in a ceramic anaerobic membrane bioreactor (AnMBR) for biofouling retardation

This study is the first to enrich a facultative QQ consortium for AI-2-based quorum sensing (QS) disruption (FQQ2) and discover its quorum quenching (QQ) performance in an anaerobic membrane bioreactor (AnMBR) for membrane fouling retardation. Herein, FQQ2 was enriched by the enrichment culture using 4,5-dihydroxy-2,3-pentanedione (DPD) followed by anaerobic screening. FQQ2 was composed of various facultative AI-2-based QQ microorganisms including Acinetobacter, Comamonas, Stenotrophomonas, and FQQ2 was capable to degrade 96.96% of DPD in 9 h. More importantly, FQQ2 prolonged membrane filtration operation by an average of 3.72 times via reduction of DPD in the AnMBR treating domestic wastewater (p ≤ 0.05). QQ was implicated to reduce the content of proteins and carbohydrates of the extracellular polymeric substances (EPS) of suspended biomass by 24.16% and 10.39%, respectively, and concentration of proteins of the soluble microbial products (SMP) by 18.77%. Parallel factor (PARAFAC) modelling of excitation-emission matrix (EEM) demonstrated that QQ could reduce the content of fulvic acid-like and humic acid-like substances, aromatic proteins and soluble-microbial-by-product-like proteins of the EPS (p ≤ 0.05) and abate the content of soluble-microbial-by-product-like proteins in the SMP (p ≤ 0.05). The lower EPS content of suspended biomass could be rendered with the reduced relative abundance of AI-2-regulated Christensenellaceae;g-, Hyphomicrobium, Leucobacter and Microbacterium by 48.48%, 76.56%, 64.78% and 59.26%, respectively, and QQ led to the reduction of the relative abundance of Christensenellaceae;g- and Leucobacter in the cake layer by 31.07% and 51.43%, respectively. Moreover, quantity of organics as well as planktonic microorganisms in the supernatant decreased in presence of FQQ2 (p ≤ 0.05). Of note, markedly lower relative abundance of AI-2-regulated Sulfurovum in supernatant by 97.74% resulted in its lower abundance of cake layer. Intriguingly, in the presence of QQ, methane production was statistically enhanced by 62.5% (p ≤ 0.05). It was closely linked to the decrease of sulfate reduction (p ≤ 0.05), which resulted from 37.93% lower abundance of sulfate-reduction Desulfomonile in the suspended biomass (p ≤ 0.05). Collectively, this study sheds lights on the development of AI-2-based QQ for biofouling control in AnMBRs.

EPS for bacterial anti-adhesive properties investigated on a model metal surface

Understanding Extracellular Polymeric Substances (EPS) interaction on a well-defined chromium surface is of importance especially for biocorrosion processes. Adsorption of EPS extracted from Pseudoalteromonas NCIMB 2021 on Cr surfaces was investigated using in situ quartz crystal microbalance (QCM) and X-ray photoelectron spectroscopy (XPS). We show that EPS adsorption is an irreversible process. The amount of adsorbed EPS increases with increasing EPS concentration in solution. For low EPS concentration, the surface is only partially covered by EPS, whereas a continuous organic film of around 15 nm is formed at the surface for high EPS concentrations. An in-depth structuration of this organic layer is evidenced with a strong enrichment of proteins in the inner part and of polysaccharides in the outer part. Adhesion of Pseudoalteromonas NCIMB 2021 has been tested on Cr surfaces covered or not by EPS extracted from Pseudoalteromonas NCIMB 2021. EPS conditioning with a 15 nm film inhibits bacterial adhesion on Cr, showing that this organic film has efficient anti-adhesive properties.

The effects of varying Zn2+ on the activated sludge properties and its distribution patterns

Metallurgy, electroplating and pharmaceutical industries generate a large amount of wastewater containing Zn2+, which influences the activated sludge properties. The present work investigated the effects of Zn2+ on sludge properties and its distribution patterns and chemical forms under a Zn2+ concentration range of 0–20 mg/L. When the influent Zn2+ concentration was 1 mg/L, parameters indicating sludge properties such as Zeta potential (−14.80 mV), contact angle (78.93°), particle size (54.43 μm) and re-flocculation (FA, 30%) reached the optimal states. Zn2+ was adsorbed by the functional groups of extracellular polymeric substances (EPS) and low EPS promoted the sludge flocculation. The lower pH affected the EPS functional groups, which in turn affected the adsorption of Zn2+. The FeMn oxidation state Zn (2.66–6.86 mg/gVSS) predominated in the sludge and decreased as sludge flocculation increased. The results provided evidence to make full use of low concentration of Zn2+ to ensure wastewater treatment performance.

Strategies for Mitigating MBR Membrane Biofouling

Membrane biofouling is a roadblock to the application of membrane bioreactors (MBR) for wastewater treatment and reuse. Strategies for the mitigation of membrane biofouling have been extensively reviewed in this paper. The review was focused on feedwater pretreatment, modified membranes, suppression of the secretion and discharge of extracellular polymeric substances (EPSs) and soluble microbial products (SMPs), and novel MRB systems. The three identified novel strategies for mitigating membrane biofouling in an MBR for wastewater reclamation are lower EPS concentration by adding D-amino acids (D-AAs) and a cationic polymer flucculant; introducing a modified membrane in an MBR; and applying a novel algae-bacteria system. Experimental results have shown that membrane biofouling has been mitigated to some extent via these strategies.

The Response of Extracellular Polymeric Substances Production by Phototrophic Biofilms to a Sequential Disturbance Strongly Depends on Environmental Conditions.

Phototrophic biofilms are exposed to multiple stressors that can affect them both directly and indirectly. By modifying either the composition of the community or the physiology of the microorganisms, press stressors may indirectly impact the ability of the biofilms to cope with disturbances. Extracellular polymeric substances (EPS) produced by the biofilm are known to play an important role in its resilience to various stresses. The aim of this study was to decipher to what extent slight modifications of environmental conditions could alter the resilience of phototrophic biofilm EPS to a realistic sequential disturbance (4-day copper exposure followed by a 14-day dry period). By using very simplified biofilms with a single algal strain, we focused solely on physiological effects. The biofilms, composed by the non-axenic strains of a green alga (Uronema confervicolum) or a diatom (Nitzschia palea) were grown in artificial channels in six different conditions of light intensity, temperature and phosphorous concentration. EPS quantity (total organic carbon) and quality (ratio protein/polysaccharide, PN/PS) were measured before and at the end of the disturbance, and after a 14-day rewetting period. The diatom biofilm accumulated more biomass at the highest temperature, with lower EPS content and lower PN/PS ratio while green alga biofilm accumulated more biomass at the highest light condition with lower EPS content and lower PN/PS ratio. Temperature, light intensity, and P concentration significantly modified the resistance and/or recovery of EPS quality and quantity, differently for the two biofilms. An increase in light intensity, which had effect neither on the diatom biofilm growth nor on EPS production before disturbance, increased the resistance of EPS quantity and the resilience of EPS quality. These results emphasize the importance of considering the modulation of community resilience ability by environmental conditions, which remains scarce in the literature.

Biological mechanism of alleviating membrane biofouling by porous spherical carriers in a submerged membrane bioreactor

In this study, porous spherical carriers were fixed around the hollow fiber membrane module to mitigate membrane biofouling. Two MBRs (R1 without carriers, R2 with carriers) were operated for 31 days under identical operating conditions to investigate the effects of the carriers on the reactor performances, the production of extracellular polymeric substances (EPS), the level of N-acyl-homoserine lactones (AHLs), and the microbial communities. The results showed that the presence of carriers in MBR was conducive to nitrogen removal and decreased the total membrane filtration resistance by about 1.7 times. Slower transmembrane pressure (TMP) rise-up, thinner bio-cakes, lower EPS production, and fewer tryptophan and aromatic proteins substances on the membrane surface were observed in R2. The polysaccharides secretion of EPS in bio-cakes was mainly regulated by C4-HSL and 3OC6-HSL in the presence of carriers. The microbial community analysis revealed that carriers addition reduced the relative abundance of EPS and AHL producing bacteria in the membrane bio-cakes and enriched the accumulation of functional bacteria conducive to nutrient removal in the mixed liquor. This study provided an in-depth understanding for the application of porous spherical carriers to alleviate membrane biofouling.

Effects of predator movement patterns on the biofouling layer during gravity-driven membrane filtration in treating surface water

Biological predation has a significant effect on biofouling layers in gravity-driven membrane (GDM) filtration systems. However, the detailed process of predatory activities is still not well known. This study explored the effects of predator movement patterns on the biofouling layer at different temperatures and the factors affecting the stable flux level. The results indicated that Demospongiae, Spirotrichea and Saccharomycetes were the main species, with the body contracting or rotating in one position at 5 °C, and Litostomatea accounted for 55.1% at 10 °C. The weak agility of these species resulted in a less porous biofouling layer with a high extracellular polymeric substance (EPS) concentration, which was responsible for the low permeate flux and the time to reach flux stability. Bdelloidea was dominant at 20 and 30 °C, and the more heterogeneous biofouling layer with a lower EPS concentration was related to their intense creeping and swimming movements and their ability to create current in the water. The grazing of spongy flocs by predators affected the GDM system performance, and a high stable flux was obtained with large and loose flocs. In addition, the diversity of the eukaryotic community decreased after the flux stabilized due to the particular predominance of Bdelloidea at high temperatures, corresponding to a high stable flux. Pollutant removal was less affected by eukaryotes, and decreased ammonia nitrogen removal rates were related to the lower activity of nitrifying bacteria. Moreover, the reliable linear correlation between the temperature and the stable flux implied that the stable flux could be well predicted in the GDM system. The findings are beneficial for developing new strategies for regulating flocs and the biofouling layer to improve the performance of GDM systems.

Integrating granular activated carbon (GAC) to gravity-driven membrane (GDM) to improve its flux stabilization: Respective roles of adsorption and biodegradation by GAC

As a low-maintenance and cost-effective process, gravity-driven membrane (GDM) filtration is a promising alternative for decentralized drinking water supply, while the low flux impedes its extensive application. In order to address such issue, an integrated process consisting of granular activated carbon (GAC) layer and GDM was developed. The performance of virgin (fresh GAC) or preloaded GAC (saturated GAC) was compared. Flux stabilization was observed both in the fresh and saturated GAC/GDM process during long-term filtration and their stable fluxes were both improved by approximately 50% relative to the GDM control. Moreover, integrating GAC with GDM contributed to efficient removals for dissolved organic compounds (DOC), assimilable organic carbon (AOC) and low molecular weight substances both in fresh and saturated GAC/GDM filtration. Compared to GDM control, coupling GAC to GDM could significantly reduce the concentrations of extracellular polymeric substances (EPS) and total cell counts (TCC) within the biofouling layer, and engineer highly heterogeneous structures of biofouling layer on the membrane surface. In the fresh GAC/GDM process, the improved flux obtained was mainly related to less coverage of biofouling layer and lower EPS concentrations due to efficient removals of membrane foulants by GAC adsorption. The achieved higher stable flux can be maintained during long-term filtration (after GAC saturation) owing to the combined effects of EPS reduction and formation of highly heterogeneous structures of biofouling layer in the saturated GAC/GDM system. Overall, the integrated GAC/GDM process can hopefully facilitate improvements both in the stabilized flux and permeate quality, with practical relevance for GDM applications in decentralized drinking water supply.

Investigation of various anode and cathode materials in electrochemical membrane bioreactors for mitigation of membrane fouling

In this study, a lab-scale Electro Membrane Bio-Reactor (EMBR) was operated for investigation of the effects of types of anode/cathode materials (Fe, Cu, SS, and Al) and electrical field (1 and 3 V) on reduction of membrane fouling. In addition, operating conditions such as, anode-cathode distance and cathode-membrane distance were investigated. Results suggest that Extracellular Polymeric Substances (EPS) and Soluble Microbial Products (SMP) in the MBR increase during filtration. EMBR demonstrates significantly lower EPS and SMP values, which is confirmed by Fourier Transform Infrared (FTIR) analysis. The results showed that Fe/Al material type for cathode and anode, electrode gap of 1.5 cm and voltage of 1 V (EMBR6) performed better in reducing membrane fouling and decreased carbohydrate (EPSc, SMPc), protein (EPSp, SMPp) and membrane fouling by 53.33%, 56.95%, and 77%, respectively. In addition, the high efficiency of COD removal was obtained for the EMBR under operational conditions of EMBR6 by 99.82% and the applied voltage reduces sludge production by 80% in these conditions. There are no reports regarding effect of electrochemical operational conditions (anode/cathode material, electrodes distance, and applied voltage) on EMBR performance, which provides significant information on understanding of the EMBR mechanism. In current study, the main aim is to provide an optimum electrochemical operational condition for EMBR in order to reduce membrane fouling effectively.