Lower Roughness Values Research Articles

Spectrogoniometry and modeling of martian and lunar analog samples and Apollo soils

We present new visible/near-infrared multispectral reflectance measurements of seven lunar soil simulants, two Apollo soils, and eight martian analog samples as functions of illumination and emission angles using the Bloomsburg University Goniometer. By modeling these data with Hapke theory, we provide constraints on photometric parameters (single scattering albedo, phase function parameters, macroscopic roughness, and opposition effect parameters) to provide additional “ground truth” photometric properties to assist analyses of spacecraft data. A wide range of modeled photometric properties were variably related to albedo, color, grain size, and surface texture. Finer-grained samples here have high single-scattering albedo values compared to their coarser-grained counterparts, as well as lower macroscopic roughness values. The Mars analog samples and Apollo soils exhibit slightly lower opposition effect width parameter values than the lunar analogs, whereas the opposition effect magnitude is not well constrained by the models. The Mars analog soils are typically relatively backscattering and consistent with fairly rough particles with a moderate density of internal scatterers, similar to the in situ observations of some soils by the Mars Exploration Rover (MER) Spirit. Some lunar analog soil models result in moderately-forward scattering behaviors, as do the two Apollo soils. Other fine-grained and/or glass-rich lunar analog samples populate a narrowly forward-scattering regime similar to model results from observations of some rover tracks observed by the MER Opportunity rover and some dust-poor “gray” rocks by the Spirit rover. An experiment to mimic the spherule-rich soils observed by Opportunity demonstrated a large decrease in single-scattering albedo compared to spherule-free soil surfaces, as well as increased surface roughness, narrow opposition effects, and a significant increase in backscattering, similar to some of the Opportunity soils. Phase reddening effects are documented in many soils as an increase in near-infrared/visible ratios with phase angle. Some samples exhibit falloffs in these ratio phase curves at phase angles beyond 50–80° that are likely related to an increased importance of surface scattering at high phase angles. None of the lunar analog soils perfectly match the modeled photometric parameters of the two Apollo soils. The phase reddening nature of the mare soil included an upturn in ratio values at phase angles <10° that was not observed for the highland sample. It remains to be verified whether this is a consistent observation between mare and highland samples.

Silver (Ag) as a novel masking material in glass etching for microfluidics applications

In this paper, we report the use of a single masking film for deep glass etching in hydrofluoric acid (HF). Thin film silver (Ag) is the key masking material in this work enabling a simple and low cost fabrication of microfluidic structures. The Ag film was deposited by evaporation and etched in a diluted nitric acid and de-ionized water solution at a ratio of 1:3. Surface morphology for different thicknesses of Ag film and its correlation to the maximum achievable etch depth is analyzed. AFM results shows low roughness values (<5 nm), indicating the Ag films are of smooth surface. With a 100 nm Ag film, a 220 μm etch depth in borosilicate glass substrates were produced and by further thickening the Ag to 300 nm, etch depths exceeding 300 μm were successfully achieved. SEM images show that thinner Ag films are of finer grains, potentially a source for pinholes formation where rapid penetration of HF along the grain boundaries peels off the Ag film from the glass surface. However, the Ag film was found not to react with HF. The process was demonstrated in the fabrication of cavities for integration with other microfluidic devices.

Performance Evaluation of Bamboo Scrimber under Planner Machining

This research evaluated the planing performance of bamboo scrimber boards at three feed speeds and three cutting depths and used two methods to assess the finished surfaces. A macroscopic grade assessment was made according to ASTM D 1666-87 for visible planing defects. The other assessment was a microscopic scale roughness test measuring surface average roughness in terms of GB/T 12472. The visible results showed that the finished surface quality of bamboo resulted mainly in Grades and , with the main defect being torn grain. The two evaluations method showed consistent results in surface quality that the highest percentage of Grade was counted and the lowest roughness value occurred. Compared with the hardwood Sawtooth oak widely used in furniture industry in China, planning quality of bamboo scrimber board is better in terms of roughness.

Thickness dependent surface microstructure evolution of bismuth thin film prepared by molecular beam deposition method

The evolution of surface microstructure on bismuth thin film deposited by molecular beam deposition method is investigated. Morphological, topographical, structural, and electrical property changes of the film with various thicknesses are studied by means of AFM, XRD, XRR, and 4-point probe. Drastic change of surface grain in shape, which transforms from round shape to polyhedral shape, is detected around 13–18 nm film thickness. Abrupt horizontal profile change of surface grain is verified with power spectral density (PSD) function. At this threshold thickness, the film shows very low roughness value and surface area ratio. Then both increase steeply as the film thickness surpasses the thickness. As the bismuth film is deposited thicker, it has textured structure and high roughness on surface. With increment of the thickness, the electrical sheet resistance of the films is significantly decreased. We explain this surface microstructure evolution on the bismuth film with the evolutionary selection model.

Contribution of the cashew gum (Anacardium occidentale L.) for development of layer-by-layer films with potential application in nanobiomedical devices

The search for bioactive molecules to be employed as recognition elements in biosensors has stimulated researchers to pore over the rich Brazilian biodiversity. In this sense, we introduce the use of natural cashew gum (Anacardium occidentale L.) as an active biomaterial to be used in the form of layer-by-layer films, in conjunction with phthalocyanines, which were tested as electrochemical sensors for dopamine detection. We investigated the effects of chemical composition of cashew gum from two different regions of Brazil (Piauí and Ceará states) on the physico-chemical characteristics of these nanostructures. The morphology of the nanostructures containing cashew gum was studied by atomic force microscopy which indicates that smooth films punctuated by globular features were formed that showed low roughness values. The results indicate that, independent of the origin, cashew gum stands out as an excellent film forming material with potential application in nanobiomedical devices as electrochemical sensors.

Development of an Economical Lapping Process

The manufacturing of silicon wafers in particular involves numerous processes such as grinding, lapping, and polishing of large diameter wafers employing expensive equipment in order to produce the required optical quality and damage-free surfaces. In the finishing of thin silicon chips for making IC chips especially, it is difficult to lap and/polish the substrate and obtain low surface integrity, surface finish and at the same time generate flat planar surfaces. This paper presents the development of a low cost lapping process, the process tried out on thin silicon chips that generated fracture-free with mirror-like surfaces of low roughness values and reasonably high degree of flatness.

The influence of process vibrations on precision polishing metrics

This work details the impact of process vibrations on precision polishing metrics such as material removal rates and surface finish. Process vibrations were measured on two different polishers operating under ‘identical’ conditions (same spindle speeds, tooling, and over-arm swing rates). Differences in the vibration signatures were noted between the two machines. Fused silica samples were polished on both machines using synthetic pitch tools and the resulting material removal rates and surface finishes compared. The machine with the greater vibration content at higher frequencies (>500Hz) produced higher material removal rates and higher low spatial frequency roughness values.

Some physical properties of In doped copper oxide films produced by ultrasonic spray pyrolysis

In this work, we have reported the effect of In doping on structural, optical and surface properties of copper oxide films obtained by a low-cost ultrasonic spray pyrolysis technique. Thicknesses, refractive indices and extinction coefficients of the films have been determined by Spectroscopic ellipsometry technique using Cauchy-Urbach model for fitting. A very good agreement was found between experimental and theoretical parameters with low MSE values. Transmission and reflectance spectra have been taken by UV Spectrophotometer, and band gap values have been determined by optical method. Structural properties of the films were investigated with X-ray diffraction patterns. In doping caused the films to growth through some certain directions. Atomic force microscope images have been taken to see the effect of In doping on surface topography and roughness of copper oxide films. Surface properties of undoped films have been improved by In doping. Lowest roughness values have been obtained for In doping at 1%. As a result, we have concluded that properties of copper oxide films which are commonly used in solar cells may have improved by In doping (especially In doped at 1%).

Toward smooth MWPECVD diamond films: Exploring the limits of the hydrogen percentage in Ar/H2/CH4 gas mixture

In Ar-rich Ar–H2–CH4 gas mixture the presence of H2 is found to be beneficial to the plasma stability. On the other hand, too high H2 percentages lead to materials showing a high surface roughness. In the present work, diamond films were grown on p-type Si (100) substrates screening different quantities of H2. The plasma phase and plasma–substrate interface were investigated by in-situ optical emission spectroscopy and pyrometric interferometry to determine the behavior of emitting species and the deposition rates, respectively. The obtained films were characterized by Raman micro-spectroscopy, AFM and SEM techniques. For H2 percentages between 6.3 and 10%, the structure and morphology are characteristic of nanocrystalline films, affording low roughness values when a buffer layer was grown between the diamond coating and the treated silicon surface.

Human finger contact with small, triangular ridged surfaces

Ridges are often added to surfaces to improve grip of objects such as sports equipment, kitchen utensils, assistive technology, etc. Although considerable work has been carried out to study finger friction generally, not much attention has been paid to understanding and modelling the effects of surface texture. Previous studies indicate that at low roughness values friction decreases as roughness increases, but then a sharp increase is seen after a threshold level of roughness is reached. This is thought to be due to interlocking. In this study an analytical model was developed to analyse the different mechanisms of friction of a fingerpad sliding against triangular-ridged surfaces that incorporated adhesion, interlocking and hysteresis. Modelling was compared with experimental results from tests on five different triangular-ridged surfaces, manufactured from aluminium, brass and steel. Model and experiment compared well. The study showed that at low ridge height and width the friction was dominated by adhesion. However, above a ridge height of 42.5 μm, interlocking friction starts to contribute greatly to the overall friction. Then at a height of 250 μm, a noticeable contribution from hysteresis, of up to 20% of the total friction, is observed.

Ultrathin Films of Variable Polarity and Crystallinity Obtained from 1,2-Polybutadiene Nanoparticle Dispersions

Characterization of ultrathin films of different polymer nanoparticles obtained at room temperature via spin-coating of aqueous dispersions and their morphology are described. Very small nanoparticles of semicrystalline 1,2-polybutadiene (PB), noncrystalline poly(1-butene) (PH), and poly(1-butenal) (PHF) were prepared via catalytic emulsion polymerization and subsequent hydrogenation or hydroformylation. The prefabricated nanoparticles were used as building blocks. The thin films obtained are continuous and transparent (n=1.5; κ=0). The properties of these films, formed from different constituents, are analyzed. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) images show that the PB-films are very smooth (rms roughness=10 nm) and polycrystalline. Recrystallization of these PB films reveals that edge-on lamellae are the constituent units. Films with very low roughness values (rms roughness <2 nm) are obtained with PH nanoparticles, due to the soft character of the nanoparticles. The AFM profile of the PHF films reveals that the surface remains structured after drying due to the high degree of the internal cross-linking that occurs in the nanoparticles. Quantification of the films' polarity (I(3)/I(1)=0.89, 1.3, and 2.1 for PHF, PB, and PH, respectively) agrees well with the previous values obtained for the polymer dispersions. Surfactant molecules are desorbed during the film formation; however, these aggregates can be removed by rinsing with water with no undesirable effects observed on the films.

Si implanted reactivation in GaN grown on sapphire using AlN and oxide cap layers

Gallium nitride (GaN) is a promising material for power electronic devices. Due to GaN sensitivity to high temperature treatments, dopant activation, after ion implant, is one of the major critical steps to be overcome. An annealing cap layer is then mandatory during high temperature treatment to avoid degradations. In this work, cap layers, such as AlN and SiO x , were deposited on Si-implanted N-type GaN. Samples were annealed using both classical (FA) and rapid thermal (RTA) annealing for times ranging from 30 s to 8 h and temperatures from 1000 to 1150 °C. Transmission Electron Microscopy has been done to observe the implanted layer structure. After cap layer removal, samples surface has been investigated through Atomic Force Microscopy measurements. Dopant activity was indirectly evaluated by Specific Contact Resistance (SCR) measurements. This work demonstrates that low SCR value (8.2 × 10 −5 Ω cm 2) with low surface roughness (∼1 nm) can be reached using RTA and an oxide cap layer. However, presence of hexagonal pits in GaN layer is difficult to avoid. Compromise between low SCR with low roughness value and low hexagonal pits density on the GaN surface must be found.

Effect of Surface Finish on Roughness, Color, and Gloss of Ornamental Granites

The effects of four of the most common types of surface finish on the appearance of five varieties of ornamental granite, all widely used in building construction and selected for their different colors, were analyzed by means of roughness, color, and gloss measurements. The results demonstrated that different surface finishes produce differences in color, especially in the lightness parameter (L* ), and that the magnitude of these differences depends on the color of the ornamental granite and is greatest in dark colored rocks. However, the variation in the color parameters with the different surface finishes did not depend on roughness, and no general conclusions could be drawn regarding the influence of the roughness on the color of ornamental granite. Gloss values were affected by the color of the ornamental granite, but in a different way for smooth and rough surfaces. Variation in gloss also depended on the mineral composition of the rock. Gloss and roughness were inversely related, but only within the range of low roughness values. In addition, the color gamut of the studied ornamental granites was defined within the CIELAB color space. These results will contribute to providing a standardized, objective method of characterizing the color of granite that will be useful for different workers in the field of building construction.

Effects of polishing on surface roughness, gloss, and color of resin composites

This study evaluated the effects of polishing on surface roughness, gloss, and color of regular, opaque, and enamel shades for each of three resin composites. Two-mm-thick resin disks made with Estelite Σ Quick, Clearfil Majesty, and Beautifil II were final polished with 180-, 1000-, and 3000-grit silicon carbide paper. Surface roughness, gloss, and color were measured one week after curing. Estelite Σ Quick had significantly lower roughness values and significantly higher gloss values as compared with Clearfil Majesty and Beautifil II. The effects of surface roughness and gloss on color (L*a*b*) differed among resin composites and by shade. Correlation coefficients between surface roughness and L*a*b* color factors were generally high for Clearfil Majesty, partially high (i.e., between roughness and L*) for Beautifil II, and low for Estelite Σ Quick. Correlation coefficients between gloss and L*a*b* color parameters were generally high for Beautifil II and low for Estelite Σ Quick and Clearfil Majesty. However, for all resin composites, the values of the color differences between 3000-grit and 180-grit polishing groups for all shades were imperceptible by the naked eye.

The effect of erbium-doped: yttrium, aluminium and garnet laser irradiation on the surface microstructure and roughness of double acid-etched implants

PurposeOne of the most frequent complications related to dental implants is peri-implantitis, and the characteristics of implant surfaces are closely related to the progression and resolution of inflammation. Therefore, a technical modality that can effectively detoxify the implant surface without modification to the surface is needed. The purpose of this study was to evaluate the effect of erbium-doped: yttrium, aluminium and garnet (Er:YAG) laser irradiation on the microstructural changes in double acid-etched implant surfaces according to the laser energy and the application duration.MethodsThe implant surface was irradiated using an Er:YAG laser with different application energy levels (100 mJ/pulse, 140 mJ/pulse, and 180 mJ/pulse) and time periods (1 minute, 1.5 minutes, and 2 minutes). We then examined the change in surface roughness value and microstructure.ResultsIn a scanning electron microscopy evaluation, the double acid-etched implant surface was not altered by Er:YAG laser irradiation under the condition of 100 mJ/pulse at 10 Hz for any of the irradiation times. However, we investigated the reduced sharpness of the specific ridge microstructure that resulted under the 140 mJ/pulse and 180 mJ/pulse conditions. The reduction in sharpness became more severe as laser energy and application duration increased. In the roughness measurement, the double acid-etched implants showed a low roughness value on the valley area before the laser irradiation. Under all experimental conditions, Er:YAG laser irradiation led to a minor decrease in surface roughness, which was not statistically significant.ConclusionsThe recommended application settings for Er:YAG laser irradiation on double acid-etched implant surface is less than a 100 mJ/pulse at 10 Hz, and for less than two minutes in order to detoxify the implant surface without causing surface modification.

Thermal, Mechanical and Microstructures Properties of Cellulose Derivatives Films: A Comparative Study

The proposal in this study was to evaluate the physical properties of different biopolymers films. The materials used were: pectin, carboxyl methylcellulose, methylcellulose, hydroxyl propylcellulose, hydroxypropyl-methylcellulose, and corn waxy starch; from these polysaccharides aqueous dispersions were prepared to 3% (w/v) for obtained films. In these biopolymer films, the thermal diffusivities (α) was evaluated by the Open Photoacoustic Cell method; also, their mechanical properties as tensile strength, elongation, and Young’s modulus were measured, their crystallinity percentage was evaluated by X-ray diffraction and microstructure through atomic force microscopy in contact mode. From the polysaccharide films, it was observed that most of them were flexible and transparent. In the case of the films, mechanical properties were found that the highest value of tensile strength and Young’s modulus corresponded to carboxyl methylcellulose with 69.17 and 1,912.20 MPa values, respectively. Also, Open Photoacoustic Cell method and X-ray diffraction measurements showed that there exist a correlation between the thermal diffusivity values and the crystallinity measured in the biopolymer films. It was also observed that α values of cellulose derived was affected by the substitution group in the molecule, reaching the highest α value, the films of carboxyl methylcellulose. Regarding the microstructural of the films, starch showed the highest roughness value (88.6 nm) whereas hydroxypropyl-methylcellulose resulted with the lowest roughness value (7.67 nm).

Study on Effect of Gases as Coolant and Lubricant on Machined Surface

To investigate the effects of gases as coolant and lubricant on machined surface, the micrograph and roughness value were obtained face to green cutting. Under the experiment conditions, water vapor and nitrogen gas may give a better restrain action to nubs adhibiting on the machined surface. And water vapor gave the lowest roughness value, while nitrogen gas has hardly help to lower roughness value. Other gases, only at a certain extent, can restrain nubs adhibiting and lower roughness value. Common characters of these gases are widely source, out of pollution, needless to disposing and so forth. With the view point of environment friendly, these gases may achieve green cutting.

A multifractal approach to characterize cumulative rainfall and tillage effects on soil surface micro-topography and to predict depression storage

Abstract. Most of the indices currently employed for assessing soil surface micro-topography, such as random roughness (RR), are merely descriptors of its vertical component. Recently, multifractal analysis provided a new insight for describing the spatial configuration of soil surface roughness. The main objective of this study was to test the ability of multifractal parameters to assess in field conditions the decay of initial surface roughness induced by natural rainfall under different soil tillage systems. In addition, we evaluated the potential of the joint use of multifractal indices plus RR to improve predictions of water storage in depressions of the soil surface (MDS). Field experiments were performed on an Oxisol at Campinas, São Paulo State (Brazil). Six tillage treatments, namely, disc harrow, disc plough, chisel plough, disc harrow + disc level, disc plough + disc level and chisel plough + disc level were tested. In each treatment soil surface micro-topography was measured four times, with increasing amounts of natural rainfall, using a pin meter. The sampling scheme was a square grid with 25 × 25 mm point spacing and the plot size was 1350 × 1350 mm (≈1.8 m2), so that each data set consisted of 3025 individual elevation points. Duplicated measurements were taken per treatment and date, yielding a total of 48 experimental data sets. MDS was estimated from grid elevation data with a depression-filling algorithm. Multifractal analysis was performed for experimental data sets as well as for oriented and random surface conditions obtained from the former by removing slope and slope plus tillage marks, respectively. All the investigated microplots exhibited multifractal behaviour, irrespective of surface condition, but the degree of multifractality showed wide differences between them. Multifractal parameters provided valuable information for characterizing the spatial features of soil micro-topography as they were able to discriminate data sets with similar values for the vertical component of roughness. Conversely, both, rough and smooth soil surfaces, with high and low roughness values, respectively, can display similar levels of spectral complexity. Although in most of the studied cases trend removal produces increasing homogeneity in the spatial configuration of height readings, spectral complexity of individual data sets may increase or decrease, when slope or slope plus tillage tool marks are filtered. Increased cumulative rainfall had significant effects on various parameters from the generalized dimension, Dq, and singularity spectrum, f(α). Overall, micro-topography decay by rainfall was reflected on a shift of the singularity spectra, f(α) from the left side (q&gt;&gt;0) to the right side (q&gt;0) to the left side (q

Effect of Artificial Aging on the Roughness and Microhardness of Sealed Composites

The application of surface sealant could improve the surface quality and success of composite restorations; however, it is important to assess the behavior of this material when subjected to aging procedures. To evaluate the effect of artificial aging on the surface roughness and microhardness of sealed microhybrids and nanofilled composites. One hundred disc-shaped specimens were made for each composite. After 24 hours, all samples were polished and surface sealant was applied to 50 specimens of each composite. Surface roughness (Ra) was determined with a profilometer and Knoop microhardness was assessed with a 50-g load for 15 seconds. Ten specimens of each group were aged during 252 hours in a UV-accelerated aging chamber or immersed for 28 days in cola soft drink, orange juice, red wine staining solutions, or distilled water. Data were analyzed by two-way analysis of variance and Fischer's test (α=0.05). Artificial aging decreased microhardness values for all materials, with the exceptions of Vit-l-escence (Ultradent Products Inc., South Jordan UT, USA) and Supreme XT (3M ESPE, St. Paul, MN, USA) sealed composites; surface roughness values were not altered. Water storage had less effect on microhardness, compared with the other aging processes. The sealed materials presented lower roughness and microhardness values, when compared with unsealed composites. Aging methods decreased the microhardness values of a number of composites, with the exception of some sealed composites, but did not alter the surface roughness of the materials. The long-term maintenance of the surface quality of materials is fundamental to improving the longevity of esthetic restorations. In this manner, the use of surface sealants could be an important step in the restorative procedure using resin-based materials.

Microstructure evolution and surface characteristics of NiP and CrN composite coatings under phosphate glasses molding process

The NiP, CrN, NiP/CrN multilayer, and NiPCrN multicomponent composite coatings were fabricated by magnetron co-sputtering. Simulation of molding process on various coating systems was conducted against phosphate glass. The 50 mol.% P 2O 5–50 mol.% ZnO glass was chosen for the molding process due to its low glass transition temperature, T g, around 400 °C and significant reaction at a high temperature. Phase evolution and surface characteristics of the coatings in the as-deposited and hot-pressed states were analyzed. Smooth surface morphology with a low roughness value below 5.0 nm was observed for the coatings under the hot pressing process. Grain growth and precipitation of the coatings were retarded under loading. Glass sticking behavior occurred in the NiP coating, while severe delamination of NiPCrN multicomponent composite coating was found. On the other hand, single layer CrN and NiP/CrN multilayer coatings showed superior surface and anti-sticking properties against phosphate glasses after the simulated molding process. The feasibility of NiP, CrN, and related composite coatings for phosphate glass molding is discussed.