Low Propagation Loss Research Articles

Efficient multi-step coupling between Si3N4 waveguides and CMOS plasmonic ferroelectric phase shifters in the O-band.

In this paper we present a thorough simulation-based analysis for the design of multi-step couplers bridging seamlessly plasmonic barium titanate oxide (BTO) ferroelectric phase shifters and thick silicon nitride (Si3N4) waveguides for the O-band. The targeted plasmonic waveguides are a hybrid plasmonic waveguide (HPW) providing low propagation losses and a plasmonic metal-insulator-metal (MIM) slot waveguide offering a high confinement factor for high modulation efficiency. The proposed plasmonic platforms are formed by Copper (Cu) providing CMOS compatibility. The analysis is based on 2D-FD eigenvalue and 3D-FDTD numerical simulations targeting to identify the optimum geometries ensuring the lowest coupling losses, calculated as 1.75dB for the HPW geometry and 1.29dB for the MIM configuration. The corresponding confinement factors are 31.39% and 56.2% for the HPW and MIM waveguides, respectively.

On-chip beam rotators, adiabatic mode converters, and waveplates through low-loss waveguides with variable cross-sections

Photonics integrated circuitry would benefit considerably from the ability to arbitrarily control waveguide cross-sections with high precision and low loss, in order to provide more degrees of freedom in manipulating propagating light. Here, we report a new method for femtosecond laser writing of optical-fiber-compatible glass waveguides, namely spherical phase-induced multicore waveguide (SPIM-WG), which addresses this challenging task with three-dimensional on-chip light control. Fabricating in the heating regime with high scanning speed, precise deformation of cross-sections is still achievable along the waveguide, with shapes and sizes finely controllable of high resolution in both horizontal and vertical transversal directions. We observed that these waveguides have high refractive index contrast of 0.017, low propagation loss of 0.14 dB/cm, and very low coupling loss of 0.19 dB coupled from a single-mode fiber. SPIM-WG devices were easily fabricated that were able to perform on-chip beam rotation through varying angles, or manipulate the polarization state of propagating light for target wavelengths. We also demonstrated SPIM-WG mode converters that provide arbitrary adiabatic mode conversion with high efficiency between symmetric and asymmetric nonuniform modes; examples include circular, elliptical modes, and asymmetric modes from ppKTP (periodically poled potassium titanyl phosphate) waveguides which are generally applied in frequency conversion and quantum light sources. Created inside optical glass, these waveguides and devices have the capability to operate across ultra-broad bands from visible to infrared wavelengths. The compatibility with optical fiber also paves the way toward packaged photonic integrated circuitry, which usually needs input and output fiber connections.

SAW Resonators and Filters Based on Sc0.43Al0.57N on Single Crystal and Polycrystalline Diamond.

The massive data transfer rates of nowadays mobile communication technologies demand devices not only with outstanding electric performances but with example stability in a wide range of conditions. Surface acoustic wave (SAW) devices provide a high Q-factor and properties inherent to the employed materials: thermal and chemical stability or low propagation losses. SAW resonators and filters based on synthetized by reactive magnetron sputtering on single crystal and polycrystalline diamond substrates were fabricated and evaluated. Our SAW resonators showed high electromechanical coupling coefficients for Rayleigh and Sezawa modes, propagating at 1.2 GHz and 2.3 GHz, respectively. Finally, SAW filters were fabricated on /diamond heterostructures, with working frequencies above 4.7 GHz and ~200 MHz bandwidths, confirming that these devices are promising candidates in developing 5G technology.

Quantum microwave photonics in radio-over-fiber systems

As the main branch of microwave photonics, radio-over-fiber technology provides high bandwidth, low-loss, and long-distance propagation capability, facilitating wide applications ranging from telecommunication to wireless networks. With ultrashort pulses as the optical carrier, a large capacity is further endowed. However, the wide bandwidth of ultrashort pulses results in the severe vulnerability of high-frequency radio frequency (RF) signals to fiber dispersion. With a time-energy entangled biphoton source as the optical carrier combined with the single-photon detection technique, a quantum microwave photonics method in radio-over-fiber systems is proposed and demonstrated experimentally. The results show that it not only realizes unprecedented nonlocal RF signal modulation with strong resistance to the dispersion but also provides an alternative mechanism to distill the RF signal out from the dispersion effectively. Furthermore, the spurious-free dynamic ranges of the nonlocally modulated and distilled RF signals have been significantly improved. With the ultra-weak detection and the high-speed processing advantages endowed by the low-timing-jitter single-photon detection, the quantum microwave photonics method opens new possibilities in modern communication and networks.

Larger-Than-Unity External Optical Field Confinement Enabled by Metamaterial-Assisted Comb Waveguide for Ultrasensitive Long-Wave Infrared Gas Spectroscopy.

Nanophotonic waveguides that implement long optical pathlengths on chips are promising to enable chip-scale gas sensors. Nevertheless, current absorption-based waveguide sensors suffer from weak interactions with analytes, limiting their adoptions in most demanding applications such as exhaled breath analysis and trace-gas monitoring. Here, we propose an all-dielectric metamaterial-assisted comb (ADMAC) waveguide to greatly boost the sensing capability. By leveraging large longitudinal electric field discontinuity at periodic high-index-contrast interfaces in the subwavelength grating metamaterial and its unique features in refractive index engineering, the ADMAC waveguide features strong field delocalization into the air, pushing the external optical field confinement factor up to 113% with low propagation loss. Our sensor operates in the important but underdeveloped long-wave infrared spectral region, where absorption fingerprints of plentiful chemical bonds are located. Acetone absorption spectroscopy is demonstrated using our sensor around 7.33 μm, showing a detection limit of 2.5 ppm with a waveguide length of only 10 mm.

Manufacturing of Er[formula omitted]-doped planar waveguides on silica-on-silicon using femtosecond laser-induced plasma

We report fabrication and characterisation of the erbium-doped planar waveguide on a silica-on-silicon (SOS) wafer-offering low loss and strong light confinement suitable for engineering optical waveguide amplifier for the C-band (1530–1565 nm) of the optical fibre communication. Here we describe an ultrafast laser plasma doping (ULPD) technique that is carried out using the plasma induced by a femtosecond laser (wavelength 800 nm) with a repetition rate of 10 kHz and a pulse duration of 45 fs. The ULPD method presented here had been applied successfully for rare earth materials doping on SOS substrates previously using a fs-laser with a pulse duration of ∼100 fs and at a repetition rate of 1 kHz. The fabricated planar optical waveguide layer onto the SOS substrate has been analysed for thickness, refractive index, optical propagation loss, photoluminescence intensity, and photoluminescence lifetime. We report a low propagation loss of <0.4 dB/cm in the C-Band, a long lifetime of 13.21 ms at 1532 nm, and the largest lifetime-density product 6.344 ×10 19 s cm −3. The low loss planar slab waveguide and a high lifetime-density product promise the further possibility of fabricating strip-loaded waveguides on the SOS platform. The proposed active waveguide fabrication methodology is potentially useful for manufacturing planar integrated optical waveguide amplifiers and lasers compatible with silicon-based photonic integrated circuits.

Low loss hybrid plasmonic photonic crystal waveguide for optical communication applications

In this paper, a new design of hybrid plasmonic photonic crystal (PhC) waveguide is proposed and analyzed at operating wavelength of 1550 nm. The suggested design consists of hybrid cylindrical core with periodic grating as a cladding region. The effective index (neff), propagation length (Lp), and normalized mode effective area (Aeff) of the supported modes are numerically investigated using full vectorial finite element method. The cladding geometry is tuned to obtain long propagation length with good field confinement. The reported plasmonic PhC with uniform grating achieves long propagation length and low propagation loss of 124 µm, and 0.035 dB/µm respectively. Further, the PhC with chirped cladding offers propagation length and low propagation loss of 162 µm, and 0.0268 dB/µm at λ = 1550 nm, respectively.

Structural optimization of femtosecond-laser-written lithium niobate waveguide by Raman spectroscopy

A new optimization method for femtosecond-laser-written lithium niobate (LN) waveguides is proposed and experimentally demonstrated to achieve low propagation loss. In this method, we use Raman spectroscopy to find detailed structural changes in LN crystal. We then use the results to optimize the laser irradiation conditions, including pulse laser energy, and laser irradiation design. In order to confirm the validity of this method, depressed cladding type LN waveguides were formed and their structural and optical characteristics were investigated in detail. Using proposed method, we succeeded in fabricating depressed cladding type LN waveguides with low propagation loss (∼0.64 dB cm−1) in the communications wavelength band. Furthermore, by analyzing the crystal structure of the depressed cladding waveguide cross-section using a Raman spectroscopy mapping system, the asymmetry of the waveguide cladding was newly clarified, providing a new insight for further improvement of the optical properties.

Sensitivity Enhancement of Group Refractive Index Biosensor through Ring-Down Interferograms of Microring Resonator.

In recent years, silicon-on-insulator substrates have been utilized for high-speed and low-power electronic components. Because of the high refractive index contrast of the silicon wire, its photonic device footprint can be significantly reduced. Moreover, the silicon photonic process is compatible with a complementary metal-oxide-semiconductor fabrication, which will benefit the high-density optoelectronic integrated circuits development. Researchers have recently proposed using the microring resonator (MRR) for label-free biosensing applications. The high-quality factor caused by the substantial electric field enhancement within the ring makes the MRR a good candidate for biomolecule detection under low analyte concentration conditions. This paper proposes an MRR chip to be a biosensor on the silicon platform through the relative displacement between the spatial ring-down interferograms at various cladding layers. The higher-order ring-down of the spatial interference wave packet will enhance the biosensing sensitivity after optimizing the coupling, MRR length, and the optical source bandwidth at the fixed optical waveguide loss. Finally, a typical sensitivity of 642,000 nm per refractive index unit is demonstrated under 0.1 μW minimum optical power detection for an MRR with a 100 μm radius. Higher sensitivity can be executed by a narrow bandwidth and lower silicon wire propagation loss.

Sodium-Based Cylindrical Plasmonic Waveguides in the Near-Infrared.

Subwavelength optical field confinement and low-loss propagation are of great significance for compact photonic integration. However, the field confinement capability of plasmonic devices is always accompanied by the inherent Ohmic loss. Although recent studies have shown that sodium (Na) exhibits lower loss than noble metals in the near-infrared band, the field confinement ability has not been adequately assessed. Meanwhile, the high chemical reactivity of Na should be regulated for practical application. Two dielectric-coated Na nanowires, consisting of cylindrical Na nanowires with one or two dielectric layers as claddings, are proposed and investigated in this paper. Based on finite element calculations, we thoroughly study the modal fields and low-loss propagation properties of dielectric-coated Na nanowires. The results demonstrate that Na exhibits lower loss and stronger field confinement than the typical plasmonic material silver. These findings indicate the performance of plasmonic devices can be considerably improved by employing the metal Na compared with devices using noble metals, which may promote the applications in subwavelength photonic devices.

On-Chip Integrated Yb3+-Doped Waveguide Amplifiers on Thin Film Lithium Niobate.

We report the fabrication and optical characterization of Yb3+-doped waveguide amplifiers (YDWA) on the thin film lithium niobate fabricated by photolithography assisted chemo-mechanical etching. The fabricated Yb3+-doped lithium niobate waveguides demonstrates low propagation loss of 0.13 dB/cm at 1030 nm and 0.1 dB/cm at 1060 nm. The internal net gain of 5 dB at 1030 nm and 8 dB at 1060 nm are measured on a 4.0 cm long waveguide pumped by 976 nm laser diodes, indicating the gain per unit length of 1.25 dB/cm at 1030 nm and 2 dB/cm at 1060 nm, respectively. The integrated Yb3+-doped lithium niobate waveguide amplifiers will benefit the development of a powerful gain platform and are expected to contribute to the high-density integration of thin film lithium niobate based photonic chip.

Ultra-broadband wavelength-swept Ti:sapphire crystal fiber laser.

An ultra-broadband wavelength-swept laser (WSL) was generated using glass-clad Ti:sapphire crystal fiber as the gain media. Due to the low signal propagation loss of the crystal fiber, the swept laser has a tuning bandwidth of 250 nm (i.e., 683 nm to 933 nm) at a repetition rate of 1200 Hz. The steady-state and pulsed dynamics of the WSL were analyzed. The 0.018-nm instantaneous linewidth corresponds to a 3-dB coherence roll-off of 7 mm. When using the laser for swept-source optical coherence tomography, an estimated axial resolution of 1.8 µm can be achieved.

Highly birefringent microstructured optical fiber for distributed hydrostatic pressure sensing with sub-bar resolution.

We demonstrate distributed optical fiber-based pressure measurements with sub-bar pressure resolution and 1 m spatial resolution over a ∼100 m distance using a phase-sensitive optical time-domain reflectometry technique. To do so, we have designed a novel highly birefringent microstructured optical fiber that features a high pressure to temperature sensitivity ratio, a high birefringence and a mode field diameter that is comparable to that of conventional step-index single mode fibers. Our experiments with two fibers fabricated according to the design confirm the high polarimetric pressure sensitivities (-62.4 rad×MPa-1×m-1 and -40.1 rad×MPa-1×m-1) and simultaneously low polarimetric temperature sensitivities (0.09 rad×K-1×m-1 and 0.2 rad×K-1×m-1), at a wavelength of 1550 nm. The fiber features a sufficiently uniform birefringence over its entire length (2.17×10-4 ± 7.65×10-6) and low propagation loss (∼3 dB/km), which allows envisaging pressure measurements along distances up to several kilometers.

Monolithic single-frequency microring laser on an erbium-doped thin film lithium niobate fabricated by a photolithography assisted chemo-mechanical etching

We overcome the difficulty in realizing a monolithic waveguide-coupled microring laser integrated on an erbium-doped thin film lithium niobate (Er: TFLN) using a photolithography assisted chemo-mechanical etching (PLACE) technique. We demonstrate an integrated single-frequency microring laser operating around 1531 nm wavelength. The PLACE technique, enabling integrated Er: TFLN photonics with low propagation loss, can thus be used to realize low cost mass production of monolithic on-chip microlasers with applications ranging from optical communication and photonic integrated circuit (PIC) to precision metrology and large-scale sensing.

Thermal release tape-assisted semiconductor membrane transfer process for hybrid photonic devices embedding quantum emitters

The ability to combine different materials enables a combination of complementary properties and device engineering that cannot be found or exploited within a single material system. In the realm of quantum nanophotonics, one might want to increase device functionality by, for instance, combining efficient classical and quantum light emission available in III–V semiconductors, low-loss light propagation accessible in silicon-based materials, fast electro-optical properties of lithium niobate, and broadband reflectors and/or buried metallic contacts for local electric field application or electrical injection of emitters. However, combining different materials on a single wafer is challenging and may result in low reproducibility and/or low yield. For instance, direct epitaxial growth requires crystal lattice matching for producing of defect-free films, and wafer bonding requires considerable and costly process development for high bond strength and yield. We propose a transfer printing technique based on the removal of arrays of free-standing membranes and their deposition onto a host material using a thermal release adhesive tape-assisted process. This approach is versatile, in that it poses limited restrictions on the transferred and host materials. In particular, we transfer 190 nm-thick GaAs membranes that contain InAs quantum dots and which have dimensions up to about 260 μm × 80 μm onto a gold-coated silicon substrate. We show that the presence of a back reflector combined with the etching of micropillars significantly increases the extraction efficiency of quantum light from a single quantum dot line, reaching photon fluxes exceeding 8 × 105 photons per second. This flux is four times higher than the highest count rates measured from emitters outside the pillars on the same chip. Given its versatility and ease of processing, this technique provides a path to realising hybrid quantum nanophotonic devices that combine virtually any material in which free-standing membranes can be made onto any host substrate, without specific compatibility issues and/or requirements.

Direct Modulation and Free-Space Transmissions of up to 6 Gbps Multilevel Signals With a 4.65-$\mu$m Quantum Cascade Laser at Room Temperature

A roadmap for future wireless communications is expected to exploit all transmission-suitable spectrum bands, from the microwave to the optical frequencies, to support orders of magnitude faster data transfer with much lower latency than the deployed solutions nowadays. The currently under-exploited mid-infrared (mid-IR) spectrum is an essential building block for such an envisioned all-spectra wireless communication paradigm. Free-space optical (FSO) communications in the mid-IR region have recently attracted great interest due to their intrinsic merits of low propagation loss and high tolerance of atmospheric perturbations. Future development of viable mid-IR FSO transceivers requires a semiconductor source to fulfill the high bandwidth, low energy consumption, and small footprint requirements. In this context, quantum cascade laser (QCL) appears as a promisingtechnological choice. In this work, we present an experimental demonstration of a mid-IR FSO link enabled by a 4.65-μm directly modulated (DM) QCL operating at room temperature. We achieve a transmission data rate of up to 6 Gbps over a 0.5-m link distance. This achievement is enabled by system-level characterization and optimization of transmitter and receiver power level and frequency response and assisted with advanced modulation and digital signal processing (DSP) techniques. This work pushes the QCL-based FSO technology one step closer to practical terrestrial applications, such as the fixed wireless access and the wireless mobile backhaul. Such a QCL-based solution offers a promising way towards the futuristic all-spectra wireless communication paradigm by potentially supporting the whole spectrum from the MIR to the terahertz (THz).

Field analysis for a highly overmoded iris line with application to THz radiation transport

Vector field analysis is presented for a highly overmoded iris-line structure that can act as a medium of transportation for THz radiation. The axisymmetric structure is capable of supporting hybrid modes with desirable features such as low propagation loss, uniformly linear polarization and approximately-Gaussian intensity profile across the iris. A specific application that can benefit from these features is the transportation of THz undulator radiation over hundreds of meters to reach the experimental halls at the LCLS facility, SLAC, Stanford. Such a structure has been modelled before as a boundary-value problem using Vainstein's impedance boundary condition and assuming infinitely-thin screens. Given that physical realizations of such screens must have finite thickness and that the THz wavelength in the 3-15 THz range is expected to be smaller than convenient screen thicknesses in practice, the question of the impact of finite screen thickness on propagation performance becomes rather pressing. To address this question, we present a mode-matching analysis of the structure, with finite screen thickness and perturbatively clustered (localized) field expansions, for computational feasibility. The effect of screen thickness is seen to lower the attenuation constant on the iris line, which is dominated by diffraction loss. The propagation loss predictions based on the Vainstein-model are compared with the numerical results from mode-matching for infinitely-thin screens, where the former method is observed to agree with the numerical results better at higher Fresnel numbers (highly-overmoded structures). The properties of the dominant mode fields are formally derived from first principles and a recommended approach is discussed for the inclusion of screen-thickness effects into propagation loss estimations.

Electrically pumped laser transmitter integrated on thin-film lithium niobate

Integrated thin-film lithium niobate (TFLN) photonics has emerged as a promising platform for the realization of high-performance chip-scale optical systems. Of particular importance are TFLN electro-optic modulators featuring high-linearity, low driving voltage and low propagation loss. However, a fully integrated system requires integration of high power, low noise, and narrow linewidth lasers on TFLN chips. Here we achieve this goal, and demonstrate integrated high-power lasers on TFLN platform with up to 60 mW of optical power in the waveguides. We use this platform to realize a high-power transmitter consisting of an electrically pumped laser integrated with a 50 GHz modulator.

Combining one and two photon polymerization for accelerated high performance (3 + 1)D photonic integration

Abstract Dense and efficient circuits with component sizes approaching the physical limit is the hallmark of high performance integration. Ultimately, these features and their pursuit enabled the multi-decade lasting exponential increase of components on integrated electronic chips according to Moore’s law, which culminated with the high performance electronics we know today. However, current fabrication technology is mostly constrained to 2D lithography, and thermal energy dissipation induced by switching electronic signal lines presents a fundamental challenge for truly 3D electronic integration. Photonics reduces this problem, and 3D photonic integration is therefore a highly sought after technology that strongly gains in relevance due to the need for scalable application-specific integrated circuits for neural networks. Direct laser writing of a photoresin is a promising high-resolution and complementary metal-oxide-semiconductor (CMOS) compatible tool for 3D photonic integration. Here, we combine one and two-photon polymerization (TPP) for waveguide integration for the first time, dramatically accelerating the fabrication process and increasing optical confinement. 3D additive printing is based on femtosecond TPP, while blanket irradiation with a UV lamp induces one-photon polymerization (OPP) throughout the entire 3D chip. We locally and dynamically adjust writing conditions to implement (3 + 1)D flash-TPP: waveguide cores are printed with a small distance between neighboring writing voxels to ensure smooth interfaces, mechanical support structures are printed at maximal distance between the voxels to speed up the process. Finally, the entire chip’s passive volume not part of waveguide cores or mechanical support is polymerized in a single instance by UV blanket irradiation. This decouples fabrication time from the passive volume’s size. We succeed in printing vertical single-mode waveguides of 6 mm length that reach numerical apertures up to NA = 0.16. Noteworthy, we achieve exceptionally low −0.26 dB injection losses and very low propagation losses of −1.36 dB/mm at λ 0 = 660 nm, which is within one order of magnitude of standard integrated silicon photonics. Finally, the optical performance of our waveguides does not deteriorate for at least ∼3000 h after printing, and remains stable during ∼600 h of continuous operation with 0.25 mW injected light.

Design and modeling of a graphene-based composite structure optical pressure sensor.

In this paper, a novel graphene-based composite structure optical pressure sensor is designed and built with the aid of modeling. A PDMS force-sensitive structural mechanics model is established to optimize the size of the pyramid array distributed on the PDMS layer so that to support high levels of sensitivity and stability. Meanwhile, a graphene waveguide optical model is established to obtain the optimized interference length (L), arm spacing (H) and core width (W), with the objectives of advanced sensitivity, low propagation loss, high resolution. The experimental results show that the pressure sensitivity of the proposed sensor is 17.86 nm/kPa and the maximum pressure that can be detected is 3.40 kPa, which is consistent with the theoretical analysis and verifies the feasibility of the design, also the modeling methods of the graphene-based composite structure optical pressure sensor.