Low Heat Research Articles

Preparation and hydration of low-carbon UHPC with high fraction of activated tuff and recycled fine powders

Due to the high energy consumption and carbon emission of cement, using active supplementary materials in concrete is widely studied. In this paper, waste tuff micropowder and recycled fine powder (RFP) with maximum replaced ratio of 70 % were investigated by alkali activation in ultra-high performance concrete (UHPC), the mechanical properties and hydration process were studied with different dosages and activators. The results show that the strength activity index of tuff and RFP both enhanced after calcium hydroxide activation. The alkali activator accelerated the hydration speed of tuff and RFP, also leaded to a low heat generated. The compressive strength was reduced with the replaced ratio of tuff and RFP, but the flexural strength was improved once tuff added and cured in appropriate temperature. In the cement-tuff/RFP system, calcium hydroxide accelerates cement hydration and activates part of the tuff and RFP to generate C-(A)-S-H to improve the strength of the mortar. Due to the low degree of tuff activation, less hydration products were formed, leaded to an increase in porosity. The RFP was effectively activated by calcium hydroxide, and the generated C-(A)-S-H and CaCO3 effectively refined the pore structure. The activation of RFP consumed limited mixing water, while the excessive CaCO3 generated by activation will cause the loss of UHPC strength.

Simple synthesis of acyl coupling conjugated microporous polymers monolithic material for synergistic capture of PM and CO2 in flue gas and process simulation

Adsorption and separation technologies based on physical adsorbents have the advantages of simple operation, low heat of adsorption and easy regeneration. They have received much attention for the capture of CO2 and PM from flue gases. However, the inherent “trade-off” between adsorption capacity and adsorption selectivity, as well as the high gas permeation resistance after powder processing and shaping, severely limit the prospects for industrial applications. Here, acyl functional groups were strategically introduced into polymer frameworks to successfully synthesize monolithic adsorbents (AC-CMPs) with a hierarchical pore structure for PM capture and CO2/N2 selective adsorption. The three-dimensional network structure composed of aligned hollow nanotubes effectively enhances the dispersion and mass transfer of gas flow per unit volume. Based on the porous media, multiphase flow model and discrete phase model, the gas flow process of PM trapped by AC-CMPs was simulated using Fluent. The simulation dynamically revealed the relationship between permeability resistance and filtration efficiency. The highly delocalized π-π conjugated porous skeleton linked by continuous covalent bonds endowed AC-CMPs with good stability, which prevented them from degrading in humid and high-temperature environments, thus keeping the adsorption capacity unchanged. The high polarity environment generated by the open oxygen atoms within the AC-CMPs framework, along with a high micro/mesopore ratio, enable it to achieve a CO2 adsorption capacity of 2.07 mmol/g at 273 K and 1 bar. Ideal adsorption solution theory calculations (IAST) and CO2/N2 column breakthrough experiments confirmed the excellent CO2 selectivity of AC-CMPs under realistic carbon capture conditions.

Reduction in environmental hazards and enhance the energy conversion from microalgae wastewater: Characteristics evaluation

AbstractThe formation of algae blooms can influence uncontrolled growth, causing hazards to aquatic ecosystems. The attention of microalgae wastewater treatment is gathering significance in bio‐energy conversion, resulting in environmental sustainability. Gasification technology is found to improve energy conversion with improved environmental sustainability. The novel research is to treat microalgae wastewater via hydrothermal gasification process with the assistance of a potassium hydroxide catalyst (KOH). During the gasification process, the gasification time is varied from 10, 20, and 30 min under a higher gasification temperature of 900°C is maintained throughout the gasification process. Effect of gasification processing time with KOH catalyst action on the percentage of molar fractions including carbon monoxide (CO), carbon dioxide (CO2), hydrogen (H2) and methane (CH4), lower heating value (LHV), syngas H2 yield, and gasification efficiency of hydrothermal gasification process for microalgae wastewater are experimentally investigated. The results of the present investigation are exposed with higher processing time with maximum gasification temperature processed with KOH catalyst offered maximum H2 fraction of 59%, reduced CH4 and LHV of 15% and 10 MJ/Nm3, optimum H2 yield of 22 mol/kg, and attained maximum gasification efficiency of 55%, respectively. The optimum gasification process parameters, including a 30‐min processing time with a higher gasification temperature of 900°C gained H2, will be suggested for energy/alternative fuel applications.

Enhanced response of thermospheric cooling emission to negative pressure pulse

Nitric oxide (NO) emission via 5.3 µm wavelength plays dominant role in regulating the thermospheric temperature due to thermostat nature. The response of NO 5.3 mm emission to the negative pressure impulse during November 06–09, 2010 is studied by using Sounding of Atmosphere by Broadband Emission Radiometry (SABER) observations onboard the Thermosphere Ionosphere Mesosphere Energetics and Dynamics (TIMED) satellite and model simulations. The TIMED/SABER satellite observations demonstrate a significant enhancement in the high latitude region. The Open Geospace General Circulation Model (OpenGGCM), Weimer model simulations and Active Magnetosphere and Planetary Electrodynamics Response Experiment measurements exhibit intensification and equatorward expansion of the field-aligned-currents (FACs) post-negative pressure impulse period due to the expansion of the dayside magnetosphere. The enhanced FACs drive precipitation of low energy particle flux and Joule heating rate affecting whole magnetosphere–ionosphere–thermosphere system. Our study based on electric fields and conductivity derived from the EISCAT Tromsø\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\\o }$$\\end{document} radar and TIEGCM simulation suggests that the enhanced Joule heating rate and the particle precipitations prompt the increase in NO cooling emission.

Numerical study of the effect of porous medium on thermal characteristics and emission performance of a novel micro combustor in a micro thermoelectric system

In this paper, a new type of micro combustor is designed to solve the problems of low output performance, insufficient heat source and low quality heat source of combustion-based micro thermoelectric systems. The combustor designed in this paper has the opposite intake arrangement, partial porous medium(PM) filling, central raised cavity and multistage sudden expansion structure. The effects of filling ratio of PM, thermal conductivity of PM and input power (Pin) on the thermal characteristics of combustor were investigated by numerical method. The results show that partially filled PM can stabilize the combustion position and shape, and increase the proportion of available energy of the combustor, so as to provide sufficient heat source for the thermoelectric system. The uniformity of combustor plane temperature increases with the increase of PM filling ratio and thermal conductivity. The combustible range of the combustor is 20–140 W. At the same time, at higher Pin, the filling ratio and thermal conductivity of the PM improve the thermal characteristics more obviously, so as to provide high quality heat source for the thermoelectric system. It is clear that strengthening heat transfer capacity, improving temperature uniformity and improving combustion stability are important ways to improve the thermal characteristics of combustor. In addition, the emission performance of the improvement effect is strong. Therefore, this research can be utilized as effective and feasible guidance for researching thermoelectric system and provide useful insights for the research of system heat source, i.e. combustor.

Numerical study on the melting performance of PCM by fractal fins in three-tube heat storage system

In order to solve the problems of low heat storage efficiency and uneven melting in the PCM area of the traditional heat accumulator, this paper takes the three-tube phase change heat accumulator with eight longitudinal fins as the basic structure to ensure that the volume of the fins in the heat accumulator is unchanged. The longitudinal fins are fractal in the shape of ' Y ', and the influence of the length and branch angle of the Y-shaped fins on the heat storage performance of the three-tube phase change heat accumulator is simulated by FLUENT software. The results show that the addition of fractal fins to the triple-tube phase change heat accumulator increases the heat transfer area and facilitates the development of natural convection compared with the addition of ordinary longitudinal straight fins, which effectively shortens the time required for the complete melting of PCM. After comprehensive analysis, the root and branch of Y-shaped fins account for 25% and 75% of the total length respectively, and the branch angle is 60°, which is the best Y-shaped fin structure. The complete melting rate of PCM is obviously improved. Compared with the ordinary straight fin heat accumulator, the heat storage rate is increased by 16.1%, and the overall heat storage performance is improved. By optimizing the design, it is found that the eccentricity has a significant effect on the melting process of the PCM. When the eccentricity is 11.5%, the overall heat storage time is the least. Compared with the original structure without eccentricity, the heat storage speed is increased, and the heat storage time is saved by about 14%. It provides a basis for the structural optimization design of phase change heat system.

Impact of Hood Steaming on Tuber Vitality of Yellow Nutsedge (Cyperus esculentus)

Cyperus esculentus is a hard-to-control, destructive perennial weed propagating and spreading through rhizomes and tubers. Currently, a combination of mechanical, cultural, and chemical measures sustained over time is required for satisfactory control of arable crops. Hood steaming is a promising thermal technique for rapid depletion of the soil tuber bank. The effect of hood steaming on C. esculentus tuber vitality was investigated using a dose–response experiment on two localities in Belgium. Steaming was performed for five durations (2, 4, 8, 16, and 32 min). Moreover, the effects of tuber burial depth (5, 15, and 25 cm), genetic C. esculentus clone (three different clones), and pedohydrological parameters (sandy and sandy, loamy soil) on hood steaming efficacy were determined. Additionally, the heat sensitivity of genetically diverse C. esculentus tubers was investigated in a laboratory incubator experiment in which incubation temperature and duration varied. To control tubers at depths of 5, 15, and 25 cm, treatment durations of 8, 16, and 32 min were required, respectively. In general, clones producing large tubers showed lower heat sensitivity. As pedohydrological parameters may affect heat transfer into the soil, they may affect steaming efficacy as well. To obtain complete control of C. esculentus tubers, soil temperature should be 50 °C or more for at least 42 min. Hood steaming is a highly suitable alternative technique for a rapid and strong depletion of the soil tuber bank in small well-delineated C. esculentus patches.

Super-Assembled Multilayered Mesoporous TiO2 Nanorockets for Light-Powered Space-Confined Microfluidic Catalysis.

In the field of sustainable chemistry, it is still a significant challenge to realize efficient light-powered space-confined catalysis and propulsion due to the limited solar absorption efficiency and the low mass and heat transfer efficiency. Here, novel semiconductor TiO2 nanorockets with asymmetric, hollow, mesoporous, and double-layer structures are successfully constructed through a facile interfacial superassembly strategy. The high concentration of defects and unique topological features improve light scattering and reduce the distance for charge migration and directed charge separation, resulting in enhanced light harvesting in the confined nanospace and resulting in enhanced catalysis and self-propulsion. The movement velocity of double-layered nanorockets can reach up to 10.5 μm s-1 under visible light, which is approximately 57 and 119% higher than that of asymmetric single-layered TiO2 and isotropic hollow TiO2 nanospheres, respectively. In addition, the double-layered nanorockets improve the degradation rate of the common pollutant methylene blue under sustainable visible light with a 247% rise of first-order rate constant compared to isotropic hollow TiO2 nanospheres. Furthermore, FEA simulations reveal and confirm the double-layered confined-space enhanced catalysis and self-propulsion mechanism.

Oral soluble shell prepared from OSA starch incorporated with tea polyphenols for the microencapsulation of Sichuan pepper oleoresin: Characterization, flavor stability, release mechanisms and its application in mooncake

The market share of Sichuan pepper oleoresin (SPO) in the flavor industry is increasing steadily; however, its high volatility, low water solubility, and poor stability continue to pose significant challenges to application. The microencapsulation prepared by emulsion embedding and spray drying is considered as an effective technique to solve the above problems. Sodium octenyl succinate starch (OSA starch) and tea polyphenols (TPs) were used to develop OSA-TPs complex as encapsulants for SPO to prepare orally soluble microcapsules. And the optimum doping of TPs was determined. SPO microcapsules have good properties with high encapsulation efficiency up to 88.13 ± 1.48% and high payload up to 41.58 ± 1.86% with low water content and high heat resistance. The binding mechanism of OSA starch with TPs and its regulation mechanism and effect on SPOs were further analyzed and clarified. The binding mechanism between OSA starch and TPs was clarified in further analyses. The OSA-TPs complexes enhanced the rehydration, release in food matrix and storage stability of SPO, and exhibited good sensory immediacy. Flavor-improved mooncakes were successfully developed, achieving the combination of mooncake flavor and SPO flavor. This study provided a valuable way to prepare flavoring microcapsules suitable for the catering industry, opened up the combined application of SPO and bakery ingredients, and was of great practical value and significance for improving the processing quality of flavor foods, driving the development of the SPO industry, and enhancing the national dietary experience.

The Impact of System Sizing and Water Temperature on the Thermal Characteristics of Floating Photovoltaic Systems

Accurately calculating the annual yield of floating PV (FPV) systems necessitates incorporating appropriate FPV-specific heat loss coefficients into the calculation, including both wind-dependent and wind-independent factors. The thermal behavior of several FPV systems has been investigated within this study, through the analysis of heat loss coefficients across various system sizes and configurations. Over a one-year period, data were collected from two measurement sites with three distinct systems: two ~50 kWp demonstrator-scale setups of Solarisfloat (azimuthal tracking) and Solar Float (East-West orientation) and a 2 MWp commercial-scale East–West system by Groenleven. The Solarisfloat demonstrator revealed a wind-dependent heat loss coefficient of 3.2 W/m3Ks. In comparison, the Solar Float demonstrator system displayed elevated wind-dependent heat loss coefficients, measuring 4.0 W/m3Ks for the east-facing module and 5.1 W/m3Ks for the west-facing module. The Groenleven system, which shares design similarities with Solar Float, showed lower wind-dependent heat loss coefficients of 2.7 W/m3Ks for the east-facing module and 2.8 W/m3Ks for the west-facing module. A notable discrepancy in the wind-dependent coefficients, particularly evident under a north wind direction, indicates a more efficient convective cooling effect by the wind on the demonstrator scale system of Solar Float. This could possibly be attributed to improved wind flow beneath its PV modules, setting it apart from the Groenleven system. Additionally, a thermal model founded on a ‘balance-of-energy’ methodology, integrating water temperature as a variable was introduced. The heat loss coefficient, dependent on the surface water temperature, fluctuated around zero, depending on whether the water temperature surpassed or fell below the ambient air temperature. It can be concluded that it is not of added value to introduce this floating specific heat loss coefficient parameter, as this parameter can be integrated in the wind speed independent Uc parameter.

Evaporated Nickel Oxide Films with Slow Annealing and Interface Modification for Perovskite Solar Cells.

Electron-beam-evaporated nickel oxide (NiOx) films are known for their high quality, precise control, and suitability for complex structures in perovskite (PVK) solar cells (PSCs). However, untreated NiOx films have inherent challenges, such as surface defects, relatively low intrinsic conductivity, and shallow valence band maximum, which seriously restrict the efficiency and stability of the devices. To address these challenges, we employ a dual coordination optimization strategy. The strategy includes low heating rate annealing of NiOx films and using an aminoguanidine nitrate spin coating process on the surfaces of NiOx films to strategically modify NiOx films itself and the interface of NiOx/PVK. Under the synergistic effect of this dual optimization method, the quality of the films is significantly improved and its p-type characteristics are enhanced. At the same time, the interface defects and energy level alignment of the films are effectively improved, and the charge extraction ability at the interface is improved. The combined treatment significantly improved the efficiency of inverted PSCs, from 17.85% to 20.31%, and enhanced device stability under various conditions. This innovative dual-coordinated optimization strategy provides a clear and effective framework for improving the performance of NiOx films and inverted PSCs.

CFDs Modeling and Simulation of Wheat Straw Pellet Combustion in a 10 kW Fixed-Bed Downdraft Reactor

This research paper presents a comprehensive study on the combustion of wheat straw pellets in a 10 kW fixed-bed reactor through a Computational Fluid Dynamics (CFDs) simulation and experimental validation. The developed 2D CFDs model in ANSYS meshing simulates the combustion process in ANSYS Fluent software 2021 R2. The investigation evaluates key parameters such as equivalence ratio, heating value, and temperature distribution within the reactor to enhance gas production efficiency. The simulated results, including combustion temperature and produced gases (CO2, CO, CH4), demonstrate a significant agreement with experimental combustion data. The impact of the equivalence ratio on the conversion efficiency and lower heating value (LHV) is systematically explored, revealing that an equivalence ratio of 0.35 is optimal for maximum gas production efficiency. The resulting producer gas composition at this optimum condition includes CO (~27.67%), CH4 (~3.29%), CO2 (~11.09%), H2 (~11.09%), and N2 (~51%). The findings contribute valuable insights into improving the efficiency of fixed-bed reactors, offering essential information on performance parameters for sustainable and optimized combustion.

Modified Bamboo Shoots Flour Derived from the Ampel Gading Bamboo (Bambusa vulgaris Schrad var. Striata): Physicochemical Properties and Potential Applications as a Thickening Agent

Modified flour is widely used in the food industry to enhance viscosity and texture. Previous research has investigated fermenting Bamboo Shoots Flour from Ampel Gading Bamboo which is rich in fiber. Physical process combination, like temperature changes, and chemical modifications using acids or bases, may alter the flour's gel-forming properties, thereby expanding its applications, including as a thickening agent. The objective of this study is to evaluate the physicochemical properties and potential applications of Modified Bamboo Shoots Flour (MBFS) as a thickening agent. The analysis demonstrated that MBSF comprises 28.41% carbohydrates, with 4.88% crude fiber and 18.68% starch, featuring 4.74% amylose and 13.94% amylopectin (wet basis). Additionally, it contains 28.10% protein and 11.17% fat (wet basis), maintaining the characteristic form of MBSF. Scanning Electron Microscope (SEM) evaluation revealed the presence of ovate-shaped, rough and irregular surface starch granules. Heating a 2% MBSF suspension to 100°C increases viscosity, solubility, and swelling power. Low acidity (pH 10) enhances swelling power without affecting viscosity significantly. Both low acidity and heat treatments enhance the thickening properties of the MBFS. This study offers fundamental insights into the physical and chemical characteristics of MBFS, thereby facilitating its potential application in final products.

Experimental Combustion and Flame Characterization of a Chemical Looping Based Oxidative Dehydrogenation Byproduct Fuel Mixture Containing High CO2 Dilution

Abstract This study investigates the combustion performance of CO2 rich fuel mixtures containing ethane and methane as active species using a constant volume combustion chamber. This fuel is obtained as byproducts of a chemical looping based oxidative dehydrogenation (Cl-ODH) process ethylene production. The byproduct gas mixture has 40.79% CO2, 39.49% ethane, and 4.88% methane by weight with other minor compounds. After initial combustion modelling, the gas fuel mixture was reduced to just the major species: CO2, ethane, and methane. The mixture was then tested for flammability limits and combustion performance under spark-ignition conditions. Effects of ambient conditions and stoichiometry like temperatures between 300 to 400 K with initial pressures from 1 to 10 bar were tested. The fuel mixture showed an overall reduced flame velocity compared to gasoline. Instability in combustion was believed to be caused by the dissociation of ethane under elevated conditions. At higher pressures, the flame produces lower cumulative heat release. Simulations were also performed using a model tuned to replicate the operations of the combustion chamber used in the experiments. Heat release and unburnt fuel mass data were calculated to identify the discrepancies in the combustion completeness at elevated pressures. The effects of CO2 quenching the flame coupled with the increased dissociation of the fuel species can lead to up to more than 75% of the fuel mixture being unburnt. Data from this study was used to modify a small-scale spark-ignition engine to use this fuel and produce usable energy.

Overview of the application of open cell foam heat exchangers

PURPOSE. Review modern highly porous cellular heat exchangers. METHODS. We conducted a broad literature review on highly porous cellular structures used as heat exchangers. We studied both domestic and foreign literature. RESULTS. We analyzed highly porous heat exchangers of various structures: stochastic (foam with open and closed cells) and ordered (honeycombs and lattices). Methods for producing open/closed cell foams and additive technologies for producing honeycomb and lattice structures have been studied. The basic properties of highly porous structures are described. The factors influencing heat transfer and hydrodynamics in highly porous cellular heat exchangers are analyzed. A review of theapplication areas of highly porous metal heat exchangers is carried out. CONCLUSION. Heat transfer and hydrodynamics in highly porous materials depend on structural parameters, such as porosity, cell size and geometry, diameter, and geometry of the strands. Increasing porosity and cell size leads to a decrease in heat transfer coefficient and pressure drop. Changing the cell geometry affects the specific surface area of the heat exchanger and the pressure drop. Cells with complex geometries, such as octet, have a large surface area and provide a high heat transfer coefficient but high resistance to coolant flow. Cells with simple geometries, such as a cube, on the other hand, provide low flow resistance and low heat transfer coefficient. In general, any structural parameter change affects heat transfer and hydrodynamics.

Galvanic Corrosion Behavior of the X80 Steel Welded Joint

Wire beam electrode techniques and classical electrochemical techniques were used to investigate the effect of the area ratio of each part of the welded joint on the galvanic corrosion behavior. The results showed that the order of the corrosion current density of the different regions in the simulated X80 steel welded joint was as follows: coarse-grained heat-affected zone > fine-grained heat-affected zone > intercritical heat-affected zone > base metal > weld metal. As the area ratio of weld metal increased, the galvanic potential shifted positively, the maximum anode galvanic current density increased and the main anode galvanic effect increased. On the other hand, as the area ratio of the base metal and the heat-affected zone decreased, the coupled potential shifted negatively and the maximum anode galvanic current density decreased. The galvanic corrosion intensity of the simulated X80 steel welded joint increased as the area ratio of the weld metal decreased and increased as the area ratio of the heat-affected zone and base metal increased. To enhance corrosion resistance, it is advisable to choose a shape with a larger groove to increase the WM area in the welded joint. Additionally, selecting a welding method with lower heat input and a higher energy density can help reduce the HAZ area in the welded joint.

Influence of laser powder bed fusion and ageing heat treatment parameters on the phase structure and physical behavior of Ni-rich nitinol parts

This paper examines the effect of ageing temperatures (400, 500, & 600 °C) and times (30, 60, & 90 min) on Ni-rich NiTi samples produced via the Laser Powder Bed Fusion (L-PBF) technique. Variations in the process parameters of the L-PBF which were examined included laser power at 150W and 180W, and the scanning strategy at 500 mm/s and 1000 mm/s. Ageing heat treatment enabled setting the functional properties of phase change temperatures, stress-strain response, and phase change enthalpies. Samples aged at 400 °C were found to have much higher austenitic finish temperature (40–60 °C) whereas those aged at 600 °C had near-zero or sub-zero Af temperatures. This was due to the lower nickel concentration resulting from the higher heat treatment temperature. Samples heat-treated at 500 °C exhibited Af temperature which was near to the room temperature and showed co-existence of both austenitic and martensitic phases. It was also found that the crystallite size increased from 6 to 22 nm for an ageing temperature of 400 °C, to between 38 and 48 nm for an ageing temperature of 600 °C. The highest microhardness value of 380HV was recorded from the lower heat treatment temperature and the lowest microhardness of 270HV was recorded for samples heat-treated at 600 °C. This decrease in the microhardness values is attributed to the increased crystallite size of the aged samples at higher temperatures. This work identifies for the first time the novel ability to control NiTi phase change temperature and mechanical properties using ageing heat treatments which is critical for the materials application for personalised stents. Higher heat treatment temperatures were found to lead to larger crystallite sizes.

Development and understanding of the lithiation/de-lithiation mechanism of a low cobalt and nickel-rich cathode material for lithium‐ion batteries

Nickel-rich LiNixMnyCo1−x−yO2 (NMC, with x ≥ 0.6) layered oxides are regarded as cathode candidates for high-energy density lithium-ion batteries (LIBs). However, this technology faces several challenges due to the scarcity of crucial raw materials such as cobalt precursors and the negative environmental impact of their extraction process. It is therefore, it becomes imperative to develop low cobalt content cathode compositions that offer alternative options with comparable electrochemical performance. Herein, we have used a systematic approach to modify the composition while keeping all other properties (particle size and morphology) constant to synthesise low-Co-cathode materials, namely LiNi0·8Mn0·1Co0·1O2 (NMC-10 %) and LiNi0·8Mn0·15Co0·05O2 (NMC-5%). A co-precipitation route using a continuous stirred thank reactor was used for synthesis. The physico-chemical properties, electrochemical performances, cycling stability, and rate capabilities of NMC-5% materials are comparable to those of NCM-10 % materials. NMC-10 % and NMC-5% half cells show initial specific discharge capacities of 191 mAh.g−1, and 185 mAh.g−1, respectively, in a voltage range of 2.8–4.3 V (vs. Li+/Li). The NMC-5% exhibits excellent thermal stability, characterized by a predominant exothermic peak at 432 °C and significantly lower total heat energy when compared to NMC-10 % counterpart, which displayed its main exothermic peak at 339 °C. The structural and electronic changes of both materials were evaluated through in operando synchrotron-based X-ray techniques. Regardless of the cobalt content, both materials show comparable structural and electronic evolution upon the de-intercalation/intercalation of Li+ ions. An irreversible phase transition at the first delithiation was observed as emphasized by diffraction of synchrotron radiations.

Novel working fluid pair of methanol/betaine-urea for absorption refrigeration system driven by low-temperature heat sources

An absorption refrigeration system (ARS) designed for low-temperature heat sources like industrial waste heat, solar-heated water, or geothermal heat can offer substantial energy-saving benefits. This study explores a novel working fluid pair comprising methanol and betaine-urea (BE-UR), forming a deep eutectic solvent (DES) system. This design capitalizes on methanol's high enthalpy of vaporization, the low heat capacity of the working pair, and the appropriate intensity and strength of the hydrogen bonding network within the solution. The proposed fluid pair shows full solubility of BE-UR in methanol at a mole ratio of 1.81 to 1 (methanol to BE-UR), with an equilibrium vapor pressure dropping to 8.59 kPa at 303.15 K. Molecular dynamics simulations unveil a microscale solution structure, showcasing a hydrogen bond network and unbonded methanol in the concentrated working fluid pair. This configuration enhances the absorption process of methanol vapor in the ARS absorption unit. Aspen Plus simulations predict a coefficient of performance (COP) exceeding 0.85, comparable to H2O/LiBr in single effect-ARS and outperforming NH3/H2O in SE-ARS by approximately 30 %, while maintaining a lower cycle ratio of about 2.

Thermodynamic analysis of anaerobic digestion of Eichornia crassipes (Water Hyacinth) biomass from the Volta River basin of Ghana using fruit waste sludge as inoculum

In order to gain understanding on the utilization of biogas fuel derived from water hyacinth (WH) biomass and render it appealing as a sustainable gaseous fuel, the study reports on its various thermophysical, combustion and thermodynamic parameters. The parameters include, specific enthalpy, internal energy, low heating value, Wobbe number index, changes in Enthalpy, Entropy and Gibbs free energy. The experimental procedure was performed at temperature range of 29±3 °C for 61 days in a BlueSens laboratory-scale anaerobic digestion equipment. It comprised of three fermenter bottles designated as F1, F2 and F3. F1 served as the control and the rest served as the test fermenter bottles. The digestion of water hyacinth and fruit waste sludge (WH+FWS) recorded the highest biogas volumes of 19,798.79 ml in fermenter F2 and 19,168.55 ml in fermenter F3 with methane contents of 53.46 % and 51.85 %, respectively. In comparison, the biogas produced exclusively from the water hyacinth (WH) biomass yielded 12,014.49 ml in F2 and 11,384.25 ml in F3, with methane contents of 46.41 % and 43.31 %, respectively. The best biogas fuel was produced from the digestion of (WH+FWS) in fermenter F2 with an internal energy and enthalpy values of 258.6 KJ/kg. K and 344.9 KJ/kg. K, respectively. A low heating value and Wobbe number of 17.51 MJ/m³ and 17.78 MJ/m³ were determined respectively. The biogas production was simulated using the Gompertz modified kinetic equation in MATLAB and an average specific rate (Kexp) of 371.49 ml/gVS.day was obtained. The rate constant (Kexp) was applied in the linearized form of the Erying-Polanyi equation to determine the changes in Enthalpy Entropy, and Gibbs free energy as -2510.66 J, -304.78 J and 94,219 J, respectively which indicated that, the anaerobic digestion process in this study was only thermodynamically feasible at low temperatures.