Low Density Research Articles

Soft-Hard segments regulated framework of Nitrogen-Doped reduced graphene oxide aerogel for efficient adsorption of pollutants

Graphene aerogel (GA) is recognized for its high porosity, rendering it a promising candidate for water treatment applications. However, its reuse potential is hampered due to inherent limitations. To address this, the present study introduces a nitrogen-doped graphene aerogel (NGA) developed by integrating polydopamine soft segments and polyaniline hard segments into the GA matrix. This approach promotes the formation of a cohesive and durable 3D network by bridging reduced graphene oxide (rGO) nanosheets, with the hard segments of polyaniline interposed among rGO layers to mitigate significant restacking, thereby enhancing surface area and adsorption sites. NGA demonstrates remarkable properties including strength (67 kPa), reversible compressibility under 64 % strain, low density (12.26 mg/cm3), and thermal stability (Tdecomposition = 679.6 °C in air), which collectively enhance its adsorption capacity and recyclability. This study further examines the influence of various factors such as pH, adsorbates (dyes and organic solvents), initial concentration, and cycle times on the aerogel’s adsorption efficacy. Additionally, simulation outcomes reveal that NGA’s adsorption kinetics and thermodynamics align more closely with the endothermic pseudo-first-order kinetic model, indicative of predominant physical adsorption mechanisms. Given its superior adsorption capabilities for pollutants, NGA holds significant promise for application in water treatment.

Adsorption of antiretroviral drugs, abacavir, nevirapine, and efavirenz from river water and wastewater using exfoliated graphite: isotherm and kinetic studies

In this work, exfoliated graphite was used to adsorb antiretroviral drugs from river water and wastewater. The exfoliated graphite was prepared from natural graphite by intercalating it with the acids and exfoliating it at 800˚C. It was characterized using Fourier Transform Infrared Spectroscopy which showed phenolic, alcoholic, and carboxylic functional groups between 1000 cm-1 and 1700 cm-1. Energy-dispersive X-ray spectroscopy results showed carbon as the main element with splashes of oxygen. The Scanning Electron Microscopy images showed increased c-axis distance between graphene layers after intercalation, which further increased after the exfoliation. The exfoliation resulted in elongated distorted cylinders, which were confirmed by the lower density (0.0068 g/mL) of exfoliated graphite material compared to the natural graphite (0.54 g/mL). The X-ray diffraction pattern showed the characteristics of hexagonal phase graphitic structure by the diffraction plane (002) at 26.74°. Raman spectroscopy results showed the natural graphite, graphite intercalated, and exfoliated graphite contained the D, G, D', and G' peaks at about 1350 cm-1, 1570 cm-1, 2440 cm-1, and 2720 cm-1, respectively indicating that the material’s crystallinity was not affected by the modification. The highest antiretroviral drugs removal (95-99%), from the water was achieved with a solution pH of 7, an adsorbent mass of 30 mg, and an adsorption time of 30 minutes. The kinetic model and adsorption isotherm studies showed that the experimental data fit well in pseudo-second-order kinetics and is well explained by Freundlich’s adsorption isotherm. The maximum adsorption capacity of the exfoliated graphite for antiretroviral drugs ranges between 1.660-197.0, 1.660-232.5, and 1.650-237.7 mg/g for abacavir, nevirapine, and efavirenz, respectively. The obtained removal percentages were 100% in river water, 63-100% in influent and 70-100% in effluent wastewater unspiked samples.

Yard phytoarchitecture for onsite sanitation of household wastewater containing copper

Copper can be found in various equipment, building materials, and consumer products. When buildings are used, copper can enter wastewater in different ways. It is challenging for occupants to remove copper physically or chemically since they can potentially reduce copper levels through yard phytoarchitecture. This study aims to formulate houseplants' suitability to become decorative plants for the yard phytoarchitecture, simultaneously as onsite sanitation. This study identified the copper deconcentration pathway in wastewater by studying published works-based research. Literature was collected and selected based on recency, accessibility, and the relationship among copper, wastewater, and plants. The study findings show that processing copper by plant has the greatest opportunity to be implemented on a building scale. The yard phytoarchitecture system involves arranging plants in the yard, which serves both as a decorative feature and a way to treat the building's wastewater. It can be used on dry yards or ponds and only requires a small amount of land. The plants used should have low leaf density and high root density. It plays a dual role consisting of onsite sanitation infrastructure and yard aesthetics, which mutually strengthen the environmental health locally and positively effect on a larger scale.

Managing osteoporosis in COPD.

Chronic obstructive pulmonary disease (COPD) is a serious respiratory disease with high morbidity, disability and mortality worldwide. Every year, many people die from the disease or its comorbidities. Osteoporosis is a common complication of COPD, which can lead to increased fractures in COPD patients, aggravate the disease, and then bring great pain and burden to patients. The possible factors leading to osteoporosis in COPD patients include systemic inflammation, corticosteroid use, vitamin D deficiency, physical inactivity, tobacco exposure, lower bone mineral density, hypogonadism, hypoxia, and anemia. In clinical practice, the rate of diagnosis and treatment of osteoporosis in patients with COPD is low. Several studies demonstrated that treating osteoporosis with bisphosphonates could improve bone density, make breathing easier, and improve the quality of life of COPD patients. However, no studies have examined the effect of anti-osteoporosis therapy on fracture prevention in COPD patients. More research is needed to clarify how to implement holistic medical interventions in COPD patients with osteoporosis. We recommend that every COPD patient be screened for osteoporosis and treated with standard medications for primary osteoporosis.

Plastic Waste Identification Using Deep Learning for Adequate Waste Management

Plastic waste management has emerged as a critical global challenge, prompting concerted efforts from conservation authorities and international organizations like the United Nations to enhance detection and classification strategies. This research distinguishes itself by harnessing advanced deep learning techniques to identify plastic materials at the micron level, surpassing traditional macro-level methods. The primary goal is to classify plastics into four major distinctions, addressing a key challenge in plastic segregation by accurately measuring thickness. Leveraging the YOLOv8 architecture, this approach enables precise classification of plastics into Polyethylene terephthalate (PETE), High Density Polyethylene (HDPE), low density polyethylene (LDPE0, and Polyvinyl Chloride (PVC) categories based on thickness. To achieve this, incorporation of hardware components such as ultrasonic sensors and NodeMCU for detecting thickness variations is used. By facilitating effective segregation according to environmental impact, this innovation revolutionizes waste reduction efforts, offering real-time identification and enhancing overall sustainability in plastic waste management.

Two-step modification strategy enhances carbon fiber/old corrugated container fiber flexible conductive film

Carbon fiber (CF) possesses inherent properties of low density, high strength, and environmental stability. Its high aspect ratio and knittability enable the formation of flexible conductive networks. Old corrugated container (OCC) is rich in cellulose and hemicellulose, rendering them flexible and exhibiting a low coefficient of thermal expansion. In this paper, CF/OCC/PVA flexible conductive films were prepared using polyvinyl alcohol (PVA) as the matrix, CF as the conductive filler and OCC as the flexible support material. Firstly, the coupling agent was grafted on the surface of CF to enhance their surface activity, improve the dispersion of CF in solution and the chemical bonding of CF to the matrix. Subsequently, sizing nanoparticles were applied to increase the roughness of the CF surface. This served to increase the volume of the conductive network and enhance the mechanical interlocking between CF and PVA. The results show that the two-step combined modification strategy have a significant positive impact on the interfacial chemical activity, contact angle, and roughness of CF. Moreover, it leads to notable improvements in various properties of the conductive film materials. This finding is relevant for the preparation of CF reinforced other matrix materials as well as for expanding the special properties and application value of CF conductive thin film materials.

The combined effect of pre-aging and Mg/Si ratio on the natural aging and bake hardening in Al-Mg-Si-0.7Cu alloys

The combined influences of pre-aging treatment (PA) and changing Mg/Si ratio on the natural aging (NA) effect and bake hardening response for a series of 6000 series alloys with excess Mg and Cu content was studied. The results showed that PA provides a clear improvement in alloy hardness after paint baking whereas a rising excess Mg (from 1.5 to 3.0) decreases this effect. The hardness in T4P temper however was generally relatively low, due to the combined effect of PA and a high Mg/Si ratio. The strong interaction energy between Cu and Mg was responsible for facilitating the clustering and precipitation processes inducing this behavior. During NA, Mg-Cu and Mg-Mg clusters were found in addition to the Mg-Si(-Cu) clusters, with the total cluster number density decreasing in excess-Mg alloys, resulting in reduced T4P temper hardness. After bake hardening, the disordered β″ precipitates, containing substructures of “low density cylinders” (LDC) and Cu sub-unit clusters, and the lath-like QP2 phases are responsible for the excellent hardening response regardless of Mg/Si ratio effects. The alloy with a Mg/Si ratio of 1.5 exhibits a low strength in T4P temper (134 MP) and very high strength (274 MPa), coupled with a good ductility (14%) after paint baking. This alloy has great potential for automotive application.

Determination of Mechanical Properties of Hybrid Composite

Abstract: Manufacturing of composite laminates is the peculiar member of science that encounter its immense utilization in various industrial areas such as sporting, automotive, aerospace and marine industries. The superior properties of composites such as stiffness, better mechanical properties, low density, and lightweight make it a candidate in engineering applications. The continuous research in this area is due to the need for seeking alternative materials with increased performance. In this report, the basalt fiber E-glass reinforced composite mechanical properties has investigated. The basalt fiber E-glass composite was formulated with hand layup moulding technique. Mechanical properties such as tensile, flexural strength and impact strength of the basalt fiber E-glass composite have been analysed

Lipoprotein Oxidation, Genetic Expression and Polymorphism of Apo A and B Gene in Patients with Coronary Artery Disease in A Pakistani Punjabi Population

Oxidative alterations of lipoproteins and numerous polymorphism locations in the apolipoprotein A1 (APOA1) and B (APOB) genes have been identified as risk factors for cardiovascular events. The aim of the study was to investigate the gene expression and the role of APOA and B gene polymorphisms in coronary artery disease (CAD) and their relationship with lipid profiles, oxidized High Density Lipoprotein (oxHDL), and oxidized Low Density Lipoprotein (oxLDL) in the Punjabi Pakistani population. A total of 200 subjects were included, of which 135 were diagnosed as having CAD and 65 were not. The lipid profile, oxHDL, and oxLDL were measured through the calorimetric method and ELISA, respectively. Quantitative variables represented by mean ± SD for normally distributed data. Gene expression was done on cDNA through Real-time PCR. Genotyping of APOA1 (rs670, rs5069) and APOB (rs693, rs11279109) were performed by PCR-RFLP (Polymerase Chain Reaction-Restriction Fragment Length Polymorphism), and gel electrophoresis was used for band visualization. Our findings showed that the oxHDL, oxLDL, APOA, B gene expression and Del genotype of APOB rs11279109 was significantly increased in CAD cases. In addition, significant high levels of oxHDL, oxLDL, serum cholesterol, VLDL, TG, and cholesterol/HDL ratio has been shown to be associated with CAD. APOB (rs11279109) has a significant impact on dyslipidemia and exhibit a higher risk of CAD (OR=3.97) while, APOB (rs693), APOA1 (rs670), (rs5069) possesses a lower risk of CAD in the population. Hence, levels of oxHDL and oxLDL as well as ApoA1 and APOB genotyping could be useful in identifying individuals who are at risk of CAD.

Conversion of Plastic Waste into Fuel by Pyrolysis

Abstract: Plastics have woven their way into our daily lives and now pose a tremendous threat to the environment. Over a 100 million tons of plastics are produced annually worldwide, and the used products have become a common feature at overflowing bins and landfills. Though work has been done to make futuristic biodegradable plastics, there have not been many conclusive steps towards cleaning up the existing problem. Here, the process of converting waste plastic into value added fuels is explained as a viable solution for recycling of plastics. Thus, two universal problems such as problems of waste plastic and problems of fuel shortage are being tackled simultaneously. In this study, plastic wastes (low density polyethylene) were used for the pyrolysis to get fuel oil that has the same physical properties as the fuels like petrol, diesel etc. Pyrolysis runs without oxygen and in high temperature of about 300°C which is why a reactor was fabricated to provide the required temperature for the reaction. The waste plastics are subjected to depolymerization, pyrolysis, thermal cracking and distillation to obtain different value-added fuels such as petrol, kerosene, and diesel, lube oil etc. Converting waste plastics into fuel hold great promise for both the environmental and economic scenarios. Thus, the process of converting plastics to fuel has now turned the problems into an opportunity to make wealth from waste.

Radiative and mechanical energies in galaxies. I. Contributions of molecular shocks and PDRs in 3C 326 N

Atomic and molecular lines emitted from galaxies are fundamental tracers of the medium responsible for the emission and contain valuable information regarding the energy budget and the strength of the different feedback mechanisms. The goal of this work is to provide a new framework for the interpretation of atomic and molecular lines originating from extragalactic sources and a robust method to deduce the mechanical and radiative energy budget from a set of observations. Atomic and molecular lines detected in a given object are assumed to result from the combination of distributions of shocks and photo-dissociation regions (PDRs) within the observational beam. The emission of individual structures is computed using the Paris-Durham shock code and the Meudon PDR code over a wide range of parameters. The total emission is then calculated assuming probability distribution functions for shocks and PDRs. A distance between the observational dataset and the model is finally defined based on the ratios of the observed to the predicted intensities. As a test case scenario, we consider the radio galaxy 3C 326 N. The dataset is composed of 12 rotational and ro-vibrational lines of and the fine structure lines of C$^+$ and O. Our interpretative framework shows that both shocks and PDRs are required to explain the line fluxes. Surprisingly, viable solutions are obtained at low density only ($ n_H < 100 $), indicating that most of the emission originates from diffuse interstellar matter. The optimal solution, obtained for $ n_H = 10 $, corresponds to a distribution of low-velocity shocks (between $5$ and $20$ km s$^ $) propagating in PDR environments illuminated by a UV radiation field ten times larger than that in the solar neighborhood. This solution implies that at least 4<!PCT!> of the total mass carried by the PDRs is shocked. The 0-0 S(0) $28 CII and OI lines originate from the PDR components, while all the other lines are mostly emitted by shocks. The total solid angles sustained by PDRs and shocks imply that the radiative and mechanical energies reprocessed by these structures are $ L UV L_ odot $ and $ L K L_ odot $, respectively, in remarkable agreement with the values of the IR luminosity deduced from the fit of the spectral energy distribution (SED) of 3C 326 N, and consistent with a small fraction of the active galactic nuclei (AGN) jet kinetic power dissipated in the interstellar medium ($ 1$<!PCT!>). This work shows that the radiative and mechanical energy budget of galaxies can be derived from the sole observations of atomic and molecular lines. It reveals the unexpected importance of the diffuse medium for 3C 326 N, in contrast to previous studies. A last-minute comparison of the model to new JWST data obtained in 3C 326 N shows a striking agreement and demonstrates the ability of the model to make accurate predictions. This framework opens new prospects for the prediction and interpretation of extragalactic observations, in particular in the context of JWST observations.

Lower Hounsfield Units at the Planned Lowest Instrumented Vertebra is an Independent Risk Factor for Complications Following Adult Cervical Deformity Surgery.

The association of Hounsfield units (HU) and junctional pathologies in adult cervical deformity (ACD) surgery has not been elucidated. Assess if the bone mineral density of the LIV, as assessed by HUs, is prognostic for the risk of complications after ACD surgery. Retrospective cohort study. HUs were measured on preoperative CT scans. Means comparison test assessed differences in HUs based on the occurrence of complications, linear regression assessed the correlation of HUs with risk factors, and multivariable logistic regression followed by a conditional inference tree derived a threshold for HUs based on the increased likelihood of developing a complication. In all, 107 ACD patients were included. Thirty-one patients (29.0%) developed a complication (18.7% perioperative), with 20.6% developing DJK and 11.2% developing DJF. There was a significant correlation between lower LIVs and lower HUs (r=0.351, P=0.01), as well as age and HUs at the LIV. Age did not correlate with change in the DJK angle (P>0.2). HUs were lower at the LIV for patients who developed a complication and an LIV threshold of 190 HUs was predictive of complications (OR: 4.2, [1.2-7.6]; P=0.009). Low bone mineral density at the lowest instrumented vertebra, as assessed by a threshold lower than 190 Hounsfield units, may be a crucial risk factor for the development of complications after cervical deformity surgery. Preoperative CT scans should be routinely considered in at-risk patients to mitigate this modifiable risk factor during surgical planning. Level-III.

Glucose and HODEs regulate Aspergillus ochraceus quorum sensing through the GprC-AcyA pathway

Aspergillus ochraceus is the traditional ochratoxin A (OTA)-producing fungus with density-dependent behaviors, which is known as quorum sensing (QS) that is mediated by signaling molecules. Individual cells trend to adapt environmental changes in a “whole” flora through communications, allowing fungus to occupy an important ecological niche. Signals perception, transmission, and feedback are all rely on a signal network that constituted by membrane receptors and intracellular effectors. However, the interference of density information in signal transduction, which regulates most life activities of Aspergillus, have yet to be elucidated. Here we show that the G protein-coupled receptor (GPCR) to cAMP pathway is responsible for transmitting density information, and regulates the key point in life cycle of A. ochraceus. Firstly, the quorum sensing phenomenon of A. ochraceus is confirmed, and identified the density threshold is 103 spores/mL, which represents the low density that produces the most OTA in a series quorum density. Moreover, the GprC that classified as sugar sensor, and intracellular adenylate cyclase (AcyA)-cAMP-PKA pathway that in response to ligands glucose and HODEs are verified. Furthermore, GprC and AcyA regulate the primary metabolism as well as secondary metabolism, and further affects the growth of A. ochraceus during the entire life cycle. These studies highlight a crucial G protein signaling pathway for cell communication that is mediated by carbohydrate and oxylipins, and clarified a comprehensive effect of fungal development, which include the direct gene regulation and indirect substrate or energy supply. Our work revealed more signal molecules that mediated density information and connected effects on important adaptive behaviors of Aspergillus ochraceus, hoping to achieve comprehensive prevention and control of mycotoxin pollution from interrupting cell communication.

Combustion characteristics of refuse-derived fuel pellets having varying plastic compositions.

The plastic fraction of refuse-derived fuel (RDF) pellets influences fuel's physico-chemical, and mechanical properties, which in turn might affect the combustion behavior of RDF. In the present study, the combustion behavior of different plastic fraction-simulated RDF pellets is reported. The simulated pellets were prepared based on the Indian commercial RDF composition. Initially, the plastic content varied from the existing fraction in Indian commercial RDF, i.e., 35% (RDF-1), to a lower plastic content of 5% (RDF-2). Physico-chemical characterization showed that a higher plastic fraction in RDF-1 reduces its pellet density by 25% as compared to RDF-2. The changes in RDF physico-chemical properties due to plastic variation are reflected in the RDF conversion process. Single-particle and packed-bed studies concluded that the lower density for higher plastic RDF-1 leads to lower conversion times (36%), and higher flame front speed (11%), which are desirable conditions for faster conversion. However, packed-bed studies also showed limitations regarding the utilization of high plastic RDF as RDF-1 has a narrow range of operating air mass flux due to the early advent of convective cooling of the bed. Finally, considering the constraints associated with the utilization of high plastic fraction (~ 35%) RDF and to maximize the effective utilization of plastic in RDF, a workable plastic fraction of 15% in RDF was proposed and tested for its combustion properties. RDF with 15% plastic showed faster conversion, higher flame front speed, and a wider range of operating air mass flux before the advent of convective cooling of the bed.

A Comparative Analysis of Low and High SiC Volume Fraction Additively Manufactured SiC/Ti6Al4V(ELI) Composites Based on the Best Process Parameters of Laser Power, Scanning Speed and Hatch Distance

Silicon carbide (SiC) exhibits intriguing thermo-physical properties such as higher heat capacity and conductivity, as well as a lower density than Ti6Al4V(ELI). These properties make SiC a good candidate for the reinforcement of Ti6Al4V(ELI) with respect to its use as a heat shield in aero turbines to increase their efficiency. The traditional materials used in aircraft structures were required to have a combination of good mechanical properties such as strength, stiffness, and hardness and low weight, as well as low thermo-physical properties such as coefficient of thermal expansion (CTE) and thermal conductivity. The alloy Ti6Al4V(ELI) has a density of 4.45 g/cm3, which is lower than that of structural steel (7.4 g/cm3) and higher than that of aluminium (2.5 g/cm3). Lower density benefits light weighting. Aluminium is the lightest of the traditional materials used but has relatively low strength. The CTE of SiC of 4.6 × 10−6/K is lower than that of Ti6Al4V(ELI) of 8.6 × 10−6/K, while the density of SiC of 3.21 g/cm3 is lower than that of Ti6Al4V(ELI) of 4.45 g/cm3. Therefore, from the theory of composites, SiC/Ti6Al4V(ELI) composites are expected to have lower densities and CTEs than those of Ti6Al4V(ELI), thus providing for lightweighting and less thermal related buckling or separation at their joints with carbon/epoxy resin panels. The specific strength, stiffness, and Knoop hardness of SiC of 75–490 kNm/kg, 132 MNm/kg, and 600–3800 GPa, respectively, are generally larger than those of Ti6Al4V(ELI) of 211 KNm/kg, 24 MNm/kg, and 880 GPa, respectively. Therefore, investigating reinforcement of Ti6Al4V(ELI) with SiC particles is worthwhile as it will lead to the formation of composites that are stronger, stiffer, harder, and lighter, with lower values of CTE. For additive manufacturing, this requires initial studies to optimise the process parameters of laser power and scanning speed for single tracks. To print single tracks in the present work, different laser powers ranging from 100 W to 350 W and scanning speeds ranging from 0.3 m/s to 2.7 m/s were used for different SiC volume fraction values of values. To print single layers, different values of hatch distance were used together with the best values of laser power and scanning speed determined elsewhere by the authors for different volume fractions of SiC. Through optical microscopy, the built tracks and their cross sections were examined. By using laser power and scanning speeds of 200 W and 1.2 m/s, and 150 W and 0.8 m/s, respectively, the best tracks at 5% and 10% volume fractions were obtained, whereas the best tracks at 25% volume fraction were achieved using a laser power of 200 W and a scanning speed of 0.5 m/s. Furthermore, the results showed that the maximum SiC volume percentage of 30% resulted in limited or no penetration. Therefore, it is concluded from the study that parts with improved mechanical properties can be produced at SiC volume fractions ranging from 5% to 25%, while parts produced at the high volume fraction of 30 % would have unacceptable mechanical qualities for the final part.

Isolation and characterization of Banyan Tree Root Filler for Polymer Composites in Light-Weight Applications

Abstract The applicability of bio fillers as reinforcement with polymers is promoted by cost- and environmentally-conscious concerns. Nowadays, a large range of reinforcements are employed for this purpose, including cellulosic fillers and natural fibres owing to the favorable mechanical behavior, minimal price, negligible tool wear, low density, and eco-friendliness etc. The main purpose of the investigation is to explore the possibilities of utilizing plant sources as reinforcing filler in polymeric matrices. In this study particulate fillers were obtained from banyan tree’s aerial roots and were subjected to various characterization such as physiochemical evaluation, Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD), thermal analysis (TGA), and Scanning Electron Microscopy (SEM). From the physiochemical analysis it was found that the banyan tree aerial root filler (BTAR) contained 40.13% of Cellulose, 15.22% of Hemicellulose, 15.31% of Lignin and 6.86% of Pectin. The density of the BTAR filler was found as 0.27 kg/cc whereas average particle size was 136.3 µm. The maximum inflection temperature referred to the maximum degradation of the BTAR filler was 295.7oC. The SEM analysis exposed the rough surface of filler, with micro-structured strands and pores. The rough surface and the pores could help in better bond ability of the matrix and reinforcement when combined. With these properties the BTAR filler could be a potential candidate as a strengthening material for polymers in different light weight applications.

Superhydrophobic Highly Flexible Triple-Network Polyorganosiloxane-Based Aerogels for Thermal Insulation, Oil-Water Separation, and Strain/Pressure Sensing.

Polyvinylpolymethylsiloxane (PVPMS)/polydimethylsiloxane (PDMS) copolymer aerogels were synthesized via consecutive radical polymerization and cohydrolytic polycondensation of vinylmethyldimethoxysilane and dimethyldimethoxysilane, followed by supercritical drying or ambient pressure drying. The resultant PVPMS/PDMS copolymer aerogels exhibit a highly porous, tunable triple-network structure consisting of interlinked hydrocarbon polymers, PVPMS and PDMS. These aerogels display superhydrophobicity (151°), low density (109 mg cm-3), low thermal conductivity (29.8 mW m-1 K-1), and adjustable pore structure. The combination of good machinability, low thermal conductivity, excellent compressive elasticity and bending flexibility, and efficient organic solvent adsorption gives these aerogels broad application prospects in thermal insulation and oil-water separation. In addition, PVPMS/PDMS/carbon nanotube (CNT) composite aerogels were obtained by incorporating the conductive CNTs, followed by vacuum drying. The resultant PVPMS/PDMS/CNT composite aerogel exhibits high sensitivity with a broad pressure sensing range in strain and pressure sensing applications.

Adaptive optics retinal imaging in patients with usher syndrome

PurposeTo determine the structure of the cone photoreceptor mosaic in the macula in eyes with retinitis pigmentosa related to Usher syndrome using adaptive optics fundus (AO) imaging and to correlate these findings with those of the standard clinical diagnostics.MethodsTen patients with a genetically confirmed retinitis pigmentosa in Usher syndrome due to biallelic variants in MYO7A or USH2A were enrolled in the study. All patients underwent a complete ophthalmological examination including best corrected visual acuity (BCVA), spectral-domain optical coherence tomography (SD-OCT) with fundus autofluorescence photography (FAF), full-field (ffERG) and multifocal electroretinography (mfERG) and Adaptive Optics Flood Illuminated Ophthalmoscopy (AO, rtx1™, Imagine Eyes, Orsay, France). The cone density was assessed centrally and at each 0.5 degree horizontally and vertically from 1–4 degree of eccentricity.ResultsIn the AO images, photoreceptor cell death was visualized as a disruption of the cone mosaic and low cone density. In the early stage of the disease, cones were still visible in the fovea, whereas outside the fovea a loss of cones was recognizable by blurry, dark patches. The blurry patches corresponded to the parafoveal hypofluorescent ring in the FAF images and the beginning loss of the IS/OS line and external limiting membrane in the SD-OCT images. FfERGs were non-recordable in 7 patients and reduced in 3. The mfERG was reduced in all patients and correlated significantly (p <0.001) with the cone density. The kinetic visual field area, measured with III4e and I4e, did not correlate with the cone density.ConclusionThe structure of the photoreceptors in Usher syndrome patients were detectable by AO fundus imaging. The approach of using high-resolution technique to assess the photoreceptor structure complements the established clinical examinations and allows a more sensitive monitoring of early stages of retinitis pigmentosa in Usher syndrome.

Effects of pelletization on biomethane production from wheat straw

ABSTRACT The high lignin content and low bulk density of wheat straw pose challenges for biogas production. To overcome these hurdles, pretreatment and biomass pelletization have emerged as viable options. Thus, this research aims to reduce the recalcitrant nature of WS by employing various thermal pretreatment techniques and identifying the optimum parameters (temperature and time). To prepare pellets, a mixture comprising wheat straw (subjected to the best pretreatment) and cow manure pellets (WCP) at varying substrate and binder (Svs/Bvs) ratios ranging from 0.5 to 2.5 were used. Parameters such as density, water absorption, and drop shattering were evaluated to evaluate the physical characteristics of produced WCP. Additionally, the biomethane yield test of WCP (exhibiting the most favourable physical characteristics) was performed with various total solids (TS) concentrations from 4 to 12%. The WS demonstrated the highest sCOD solubilisation of 9066 mg/L when subjected to a hot air oven pretreatment (90 min at 110°C). The physical qualities of WCP were found to be dependent on the Svs/Bvs ratio (with the optimal ratio being 2.0). It was also observed that a TS content of 6% yielded the highest biomethane production (253.85 mL/g-VSconsumed). In summary, this study’s conclusion waves the path of management of wheat straw and cow dung while simultaneously generating bioenergy.

Association between socioeconomic deprivation and bone health status in the UK biobank cohort participants.

Socioeconomic deprivation is associated with many illnesses including increased fracture incidence in older people. However, the effect of deprivation on total bone health status has not been well defined. To examine the relationship between socioeconomic deprivation and poor bone health and falls, we conducted a cross-sectional study using baseline measures from the United Kingdom (UK) Biobank cohort comprising 502,682 participants aged 40-69years at recruitment during 2006-2010. We examined four outcomes: 1) low bone mineral density/osteopenia, 2) fall in last year, 3) fracture in the last five years, and 4) fracture from a simple fall in the last five years. To measure socioeconomic deprivation, we used the Townsend index of the participant's residential postcode. At baseline, 29% of participants had low bone density (T-score of heel < -1 standard deviation), 20% reported a fall in the previous year, and 10% reported a fracture in the previous five years. Among participants experiencing a fracture, 60% reported the cause as a simple fall. In the multivariable logistic regression model after controlling for other covariates, the odds of a fall, fracture in the last five years, fractures from simple fall, and osteopenia were respectively 1.46 times (95% confidence interval [CI] 1.42-1.49), 1.26 times (95% CI 1.22-1.30), 1.31 times (95% CI 1.26-1.36) and 1.16 times (95% CI 1.13-1.19) higher for the most deprived compared with the least deprived quantile. Socioeconomic deprivation was significantly associated with poor bone health and falls. This research could be beneficial to minimise social disparities in bone health.