Circuit Losses Research Articles

Design of a bus-based battery equalization with zero-current switching

A novel any cell to any cell equalization circuit topology with small column, low weight, low cost, and high efficiency is proposed for serial-connected batteries, especially suitable for unmanned aerial vehicles, satellites, and other fields with strict requirements on size, weight, reliability, and safety. To solve the problems of high switching losses in equalization circuits and low reliability of complex control schemes. A half-bridge circuit to convert the DC voltage of the battery into AC voltage is employed, and the energy is exchanged autonomously via the bus. At the same time, LC resonant circuit is used to achieve zero-current switching of the MOSFET, thus reduces greatly the switching losses. The working principle is analyzed by theoretical derivation, and the parameters of the circuit are optimized through circuit simulation. Furthermore, experiments which support six cells equalization are carried out to verify the feasibility and advantage of this topology. This equalization uses a bus-type architecture to improve equalization efficiency and topological flexibility making it even more valuable in the industrial and aerospace fields.

Impacts of Injection Parameters on the Mixture Formation and Performance of Two-Stroke Spark-Ignition Direct-Injection Aviation Kerosene Engine

Abstract Two-stroke spark-ignition engines play a significant role in the field of power sources of small and medium unmanned aerial vehicles. There is a certain transition from burning gasoline to aviation kerosene (or heavy oil) and from carburetor or inlet injection system to direct-injection fuel system. However, the performance of two-stroke spark-ignition direct-injection engines fueled with aviation kerosene was not very ideal under heavy loads. Generally, the mixture formation is very important for engine combustion and performance, while injection parameters have great effects on mixture formation. Thus, various injection parameters of a two-stroke direct-injection kerosene engine were examined here. The results showed too early or too late injection timing (tinj) would deteriorate the mixture formation, resulting in lower brake power and brake thermal efficiency. Here the most suitable tinj was 150 deg CA BTDC. Too high or too low injection pressure (pinj) caused fuel short circuit loss and poor mixture quality, so the optimum pinj was 10 MPa. Too large injector installation angle (β) easily results in fuel spray impingement, and too small β causes fuel short circuit loss. Therefore, the best β was concluded to be 30 deg in this paper.

Novel Auxiliary Resonant Pole Inverter and its Optimal Control Strategy

Conventional inverters operate in hard‐switching mode, and as the switching frequency increases, the switching losses increase dramatically. Increasing the switching frequency helps reduce the size and cost of the inverter, but too high a switching frequency generates greater switching losses, which affects the inverter's transmission efficiency. In response to the problem that conventional hard‐switching inverters cannot be higher in frequency and have high switching losses and low transmission efficiency, an optimized auxiliary resonant commutated inverter and control strategy are proposed to make the inverter work in soft‐switching mode, which helps reduce the switching losses. The auxiliary converters in the bridge arm topology of each phase of the three‐phase inverter are divided into two groups, and the operating auxiliary converters are selected according to the direction of the load current. When the load current direction is positive, the upper bridge arm auxiliary device works and the lower bridge arm auxiliary device turns off, similarly when the load current direction is negative, the lower bridge arm auxiliary device works and the upper bridge arm auxiliary device turns off, this can ensure that only one group of devices works every half cycle, making the control strategy simple and reducing auxiliary circuit losses. Simulation and experimental verification of the effectiveness of the proposed scheme. © 2023 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC.

New schemes for connecting oscillators as a part of plasma ignition systems for gas turbine engines

The effectiveness of new schemes for connecting of oscillators in plasma ignition systems of gas turbine engines is analyzed. The most efficient scheme for connecting an oscillator to reduce losses in the power circuit of the ignition system with an increased igniting ability of the plasmatron is determined. In the plasma torch, there are two types of discharges — continuous arc and pulsed capacitive, while the instantaneous power of a capacitive discharge of short duration is several orders of magnitude higher than the instantaneous power of the arc discharge. The dynamics of discharge processes in the oscillator is estimated. Analytical expressions are presented for the main parameters of pulsed discharges: maximum discharge current, energy and duration of discharges. Keywords: oscillator, plasmatron, plasma ignition system, electric arc. gabidullina.zg@ugatu.su

Symmetrical dicyano-based imidazole molecule-assisted crystallization and defects passivation for high-performance perovskite solar cells

Benefiting from the simple and low-cost fabrication of the one-step anti-solvent spin-coating process, the perovskite solar cells (PSCs) have a boost development. However, a great number of defects are generated during solution-fabrication process, retarding the development of PSCs seriously. In this study, the utilization of 4,5-dicyanoimidazole (DCI) as an additive for perovskite precursor solution was investigated. The presence of the double –CN groups in DCI facilitated the formation of Lewis acid-base coordination with unsaturated Pb2+ ions, as well as interaction with I- anions by the –NH- moiety, resulting in the enhanced perovskite film crystallinity, the reduced grain boundaries, and a significant reduction in the defects density of the perovskite film. The decreased trap-assisted recombination and voltage open circuit (VOC) losses in the PSC resulted in the improved photovoltaic performance of device treated by DCI molecule, the PCE increased from 19.59 % to 21.87 % significantly. Moreover, the unencapsulated device with DCI additive exhibited a remarkable 87.8 % retention of its initial PCE after exposure under 10–20 % relative humidity for 60 days, demonstrating an excellent stability than control device.

Design Considerations of Multi-Phase Buck DC-DC Converter

The main objective of this article is to propose a rational methodology for designing multi-phase step-down DC-DC converters, which can find applications both in engineering practice and in power electronics education. This study discusses the main types of losses in the multi-phase synchronous buck converter circuit (transistors’ conduction losses, high-side MOSFET’s switching losses, reverse recovery losses in the body diode, dead time losses, output capacitance losses in the MOSFETs, gate charge losses in MOSFETs, conduction losses in the inductor, and losses in the input and output capacitors) and provides analytical dependencies for their calculation. Based on the control examples for applications characterized by low voltage and high output current, the multi-phase buck converter’s output and input current ripples are analyzed and compared analytically and graphically (3D plots). Furthermore, graphical results of the converter efficiency at different numbers of phases (N = 2, 4, 6, 8, and 12) are presented. An analysis of the impact of various parameters on power losses is conducted. Thus, a discussion on assessing the factors influencing the selection of the number of phases in the multi-phase synchronous buck converter is presented. The proposed systematized approach, which offers a fast and accurate method for calculating power losses and overall converter efficiency, reduces the need for extensive preliminary computational procedures and achieves optimized solutions. Simulation results for investigating power losses in 8-phase multi-phase synchronous buck converters are also presented. The relative error between analytical and simulation results does not exceed 4%.

Modeling of battery energy storage systems for AGC performance analysis in wind power systems

Battery energy storage system (BESS) is being widely integrated with wind power systems to provide various ancillary services including automatic generation control (AGC) performance improvement. For AGC performance studies, it is crucial to accurately describe BESS’s power regulation behavior and provide a correct state of charge (SOC). In addition, BESS model is required to maintain a sufficiently high simulation speed, since it usually is involved in hour- or day-scale simulations. Different from existing models, this paper develops a new BESS model which considers DC-AC converter control, DC link circuit and switching loss, thus providing an accurate power regulation behavior. In addition, it also considers the nonlinear relationship between open-circuit voltage and SOC of battery so that it provides a correct SOC. As a whole, the BESS is simplified as a controlled current source with fundamental frequency (50/60 Hz) and described by algebraic phasor equations to reduce computational burden. This makes the proposed model capable of finishing hour- or day-scale simulations within a few minutes. Time-domain simulations are used to validate and compare the simulation accuracy with the classical first-order transfer function model and electromagnetic model. Based on the proposed model, this paper also introduces and verifies a new BESS-based strategy to improve the AGC performance of wind farms.

A Single-Phase Seven-Level Triple Boost Inverter for Grid-Connected Transformerless PV Applications

A new seven-level common ground (CG) switched capacitor (SC)-based grid tied transformerless inverter has been introduced in this paper, which has three times boosting capability of input voltage. Thus, this inverter is preferable for low voltage PV applications without any boost conversion stage. To step-up the input PV voltage and facilitate seven steps in output voltage, two SC cells are connected in parallel. A virtual dc link capacitor serves key role for negative half cycle on behalf of H-Bridge and helping in constructing topology with common ground. The common grounding configuration of this inverter helps in bypassing the stray capacitance, which eliminates the leakage current and consequently reduces EMI considerably. Hence, further no requirement of any electro-magnetic interference (EMI) filter for electro-magnetic compatibility (EMC). Additionally, this inverter handles reactive power during the grid's lagging/leading power factor (pf) condition. To regulate active and reactive grid power, a proportional resonant (PR) current controller is designed. The proposed modulation scheme helps in balancing capacitor's voltages at their base values with allowable ripple. A detailed comparison also has been presented with other contemporary seven level inverters. The inverter circuit details, control technique, PWM scheme, thermal modeling, and loss analysis with component design guidelines are described in detail. Experimental results are presented to validate the effectiveness and feasibility of this proposed inverter.

Research on power management circuit of magnetic field energy harvesting for wireless sensor

In order to solve the power supply problem of wireless sensors in the power cable environment, the changing magnetic field around the cable is used, and the open energy harvesting coil and power management circuit are used to supply power to the sensor. However, improving circuit applicability and output efficiency is the key. For this reason, through the circuit principle and simulation analysis, the basic model of the power management circuit is established, and the overvoltage protection and energy storage unit are designed for the special environment of the cable to solve the problem of circuit protection and energy supply dead zone. Then reduce the circuit loss according to the circuit topology design. Finally, an experimental platform is built to verify the output effect of the power management circuit. The voltage induced by the magnetic induction power acquisition module can obtain a stable and reliable output voltage through the power management circuit, which can realize the self-sufficiency of the power supply of the wireless sensor.

A Novel Three-Phase Omnidirectional Wireless Power Transfer System With Zero-Switching-Loss Inverter and Cylindrical Transmitter Coil

Aiming at the problems of large switching loss and large output power fluctuation in the existing omnidirectional wireless power transfer (OWPT) system, a novel OWPT system with zero-switching-loss inverter and cylindrical transmitter coil is proposed. By introducing an auxiliary resonant network with simple structure and low-loss on each phase arm of the three-phase inverter, zero-voltage switching (ZVS) turn-ON and zero-current switching (ZCS) turn-OFF within the full power range can be acquired. The switching loss in the main circuit of inverter is reliably eliminated. The transmitter coil is a cylindrical coil composed of the three curved rectangular coils, whose excitation current amplitude is equal and the phase difference is 120°. It can arise a spatial rotating magnetic field around the transmitter coil and provide an omnidirectional energy transmission channel. The operating principle of soft-switching is analyzed in detail, and the design rules of soft-switching in full power range and the parameter design method of coupler to reduce the fluctuation of output power are given. Ultimately, an experimental prototype is used to verify the feasibility of the proposed OWPT system. The experimental results indicate that the system output power is retained at 93.4W∼104.7W and transfer efficiency is retained at 71.2%∼78.1% under arbitrary angular misalignment of receiver.

Novel SVPWM Method Based on Zero-Voltage Notch of Resonant DC-Link Inverter

In order to decrease the switching loss of the auxiliary circuit of the resonant DC link (RDCL) inverter and improve the voltage utilization and system efficiency, this paper presents a new space vector pulse width modulation (SVPWM) method based on the zero-voltage notch of the resonant DC link inverter. This resonant DC link inverter reduces the current stress in the main circuit by paralleling auxiliary switch. And this method makes the operation of the auxiliary resonant circuit (ARC) less frequent, thus reducing the losses of the ARC and therefore improving the system efficiency. At the same time, this method analyzes and compensates for the missing voltage vectors based on the ideal output voltage, so that the inverter output voltage vector under this modulation is the same as the ideal SVPWM output voltage vector. Compared with the original modulation of RDCL inverter, this method does not change the switching sequence, the switching times, and the action time of the vector, while reducing the switching ripple. The effectiveness and feasibility of the modulation strategy is verified in the paper through theoretical analysis as well as experiments.

Circulating and Eddy Current Losses in Coreless Axial Flux PM Machine Stators With PCB Windings

Printed circuit board (PCB) stators in coreless axial flux permanent magnet (AFPM) machines have been proposed, designed, and studied for use in multiple industries due to their design flexibility and reduction of manufacturing costs, volume, and weight compared to conventional stators. This paper investigates mechanisms and methods of approximating open circuit losses in PCB stators within example wave and spiral winding topologies for a dual rotor, single stator configuration using 3D FEA, analytical hybrid techniques and experiments. The effect of rotor magnet shape, end winding, and active conductor geometry on eddy currents is studied, and some mitigation techniques are proposed. Through stator equivalent circuit analysis, circulating current losses caused by mechanical abnormalities and magnetic circuit asymmetry are assessed. Possible strategies and schemes to minimize circulating current losses are also described. The trade-off between stator loss components and some practical design considerations are outlined in detail. The open circuit power losses of a prototype coreless AFPM motor were experimentally tested using multiple example PCB stators and emulated rotor asymmetries, with the findings being comparable to the FEA and hybrid analytical methods results.

Cefiderocol is Not Sequestered in an Ex Vivo Extracorporeal Membrane Oxygenation (ECMO) Circuit.

Extracorporeal membrane oxygenation (ECMO) is used in critically ill patients that require respiratory and/or cardiac support. Cefiderocol is a novel siderophore antibiotic that may require use in infected critically ill patients supported by ECMO. The objective of this study was to determine the loss of cefiderocol through an ex vivo adult ECMO circuit using a Quadrox-iD oxygenator. A 3/8-inch, simulated, ex vivo closed-loop ECMO circuit was prepared with a Quadrox-iD adult oxygenator and primed with fresh whole blood. Cefiderocol was administered into the circuit to achieve a starting concentration of approximately 90 mg/L. Post-oxygenator blood samples were collected at 0, 0.25, 0.5, 1, 2, 4, 6, 12, and 24 h after the addition of the drug to determine the loss in the circuit. A glass control jar was prepared with the same blood matrix and maintained at the same temperature to determine drug degradation. The experiment was conducted in triplicate. The rate of cefiderocol loss in the ECMO circuit was compared with that in the control by one-way analysis of variance. At 0h, the difference between the pre- and post-oxygenator concentrations was -4 ± 4% (range 0 to -7%). After 24h, the cefiderocol percent reduction was similar between the ECMO circuit and control (50% ± 13 vs. 50% ± 9, p=1.0). The degradation rate of cefiderocol did not differ significantly within the ECMO circuitand control, suggesting no loss due to sequestration or adsorption. Pharmacokinetic studies in patients supported by ECMO are warranted to determine final dosing recommendations.

A Family of Zero-Voltage-Transition Magnetic Coupling Bidirectional DC/DC Converters

In this paper, a family of zero-voltage-transition (ZVT) magnetic coupling bidirectional DC/DC converters (BDCs) is proposed. The coupling inductor has two functions: to serve as a filter; and to provide the auxiliary current. In addition, the phase-shifting control method is used to reduce the conduction loss of the auxiliary circuit. The auxiliary switches are all working under zero-current-switching (ZCS) conditions; thus, all the switches have no switching loss. Furthermore, compared with the traditional ZVT implementation method based on the coupled inductor, this topology avoids the input source current notch and has a smaller ripple. Finally, a prototype of 800 W BDC is built to verify the feasibility of the proposed topology.

Quantum bath suppression in a superconducting circuit by immersion cooling

Quantum circuits interact with the environment via several temperature-dependent degrees of freedom. Multiple experiments to-date have shown that most properties of superconducting devices appear to plateau out at T ≈ 50 mK – far above the refrigerator base temperature. This is for example reflected in the thermal state population of qubits, in excess numbers of quasiparticles, and polarisation of surface spins – factors contributing to reduced coherence. We demonstrate how to remove this thermal constraint by operating a circuit immersed in liquid 3He. This allows to efficiently cool the decohering environment of a superconducting resonator, and we see a continuous change in measured physical quantities down to previously unexplored sub-mK temperatures. The 3He acts as a heat sink which increases the energy relaxation rate of the quantum bath coupled to the circuit a thousand times, yet the suppressed bath does not introduce additional circuit losses or noise. Such quantum bath suppression can reduce decoherence in quantum circuits and opens a route for both thermal and coherence management in quantum processors.

Review of Active Circuit and Passive Circuit Techniques to Improve the Performance of Highly Efficient Energy Harvesting Systems

In piezoelectric energy harvesting systems, energy harvesting circuits are the interface between piezoelectric devices and electrical loads. The conventional view of this interface is based on the concept of impedance matching. In fact, in the power supply circuit can also apply as an electrical boundary conditions, such as voltage and charge, to piezoelectric devices for each energy conversion cycle. The major drawback of piezoelectric power harvesting have low-power relationships in systems within (in the range of μW to mW), then system also have significantly reduced any potential losses in circuits that make up the EH system, whereas other condition into careful selection of circuits and components can enhanced the energy harvesting performance and electricity consumption. In the study of energy harvesting systems, it is an energy harvesting system approach that using active and passive electronic circuit to control voltage and or charge on piezoelectric devices as proposed and review to mechanical inputs for optimized energy conversion. Several factors in the practical limitation of active and passive energy consumption, due to device limitations and the power efficiency of electronic circuits, will be introduced and have played an important role into to enhance optimum and increase efficiency of energy harvesting system.

Calculation of Losses in the Magnetic Circuit of a High-Speed Switched Reluctance Generator

Calculation of Losses in the Magnetic Circuit of a High-Speed Switched Reluctance Generator

Energy Saving and Loss Reduction Measures Optimization for Distribution Networks

High conversion rate energy plays an increasingly important role in the “double carbon” goal as well as the energy saving and emission reduction goals. The technology of loss reduction and energy saving has become the focus of modern power system construction. A technical line loss reduction technique is implemented in this work for feeders in the distribution network with abnormal losses in the technical circuit. Power flow calculations, analysis, and comparison are conducted using the Newton-Lafson method. Considering the best single investment benefit ratio measure under the same type of multi-measure loss reduction, the genetic mutation algorithm was used to sort the combination schemes, the efficient algorithm was used to solve the optimal scheme, and the multi-type measure solving model of the distribution network was established.

An Efficient Resonant Pole Inverter Without Constant Circulating Current Loss in the Auxiliary Circuit

An Efficient Resonant Pole Inverter Without Constant Circulating Current Loss in the Auxiliary Circuit

Simulation Study on a Planar Quasi-Optical Waveguide Circuit for a W-Band Gyro-TWT With Stability Improvement

In this article, a planar quasi-optical waveguide (PQOW) circuit is proposed for vacuum electron devices (VEDs) for the first time. The circuit is made of a series of metamaterial pillars attached to a pair of parallel plates for phase compensation. It can propagate quasi-optical modes as a pair of concave mirrors does, while the lower order HE <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$_{\text{0}\textit{n}}$</tex-math> </inline-formula> modes experience much heavier circuit loss compared to that of convention confocal waveguide circuits, which can improve the backward oscillation (BWO) stability of gyro-amplifiers. As an example, a W-band gyro-amplifier with PQOW circuits to replace conventional confocal circuits is designed. The 3-D particle-in-cell simulation demonstrated that the circuit is capable of producing stable high-power radiation within 96–108 GHz, with an electron efficiency of about 15% over the entire bandwidth.