Lithium Niobate Ridge Waveguide Research Articles

Frequency-correlated photon-pairs tunable across the telecom spectrum via cascaded SHG ＋ SPDC in PPLN

We explore the cascaded second-order (χ(2)) nonlinear process of second-harmonic generation (SHG) + spontaneous parametric down-conversion (SPDC) at telecom wavelengths in a type-0 phase-matched Zn-diffused 5% MgO-doped periodically poled lithium niobate (PPLN) ridge waveguide. We simulate the waveguide modes using finite element method (FEM) to determine the signal and idler peak wavelengths produced via the cascading effect at a particular temperature and pump wavelength. We also derive an analytical expression for the effective χ(3) conversion efficiency (equivalently, the signal/idler photon flux) and experimentally verify that the cascaded process produces discrete temperature-tunable signal/idler sidebands (around a ∼1550-nm pump) that can be continuously tuned across the E-, S-, L-, and U-bands of the telecom spectrum. Such frequency-correlated photon pairs produced in a fiber-coupled integrated setup could have applications in quantum computing and communication.

One-dimensional grating coupler on lithium-niobate-on-insulator for high-efficiency and polarization-independent coupling.

A metal-based one-dimensional grating coupler on an x-cut lithium-niobate-on-insulator wafer structure for a polarization-independent fiber interface is designed and demonstrated. By using a metal-based plasmonic mode, the diffractive angle for the two polarized modes in the lithium niobate ridge waveguide can be tuned to be the same. The polarization dependence of the grating coupler therefore can be effectively reduced. The fabricated device exhibits -3.56-dB and -4.08-dB peak coupling losses per coupler at 1573 nm for the TE and TM modes, respectively. The polarization-dependent losses are less than 0.69 dB in a 44-nm wavelength range. The demonstrated grating coupler can serve as a polarization-independent optical fiber interface on lithium-niobate-on-insulator and facilitate on-chip polarization diversity applications.

Highly efficient, modal phase-matched second harmonic generation in a double-layered thin film lithium niobate waveguide.

In this contribution, we numerically investigate second harmonic generation in double-layered lithium niobate on the insulator platform by means of the modal phase matching. The modal dispersion of the ridge waveguides at the C waveband of optical fiber communication is calculated numerically and analyzed. Modal phase matching can be achieved by changing the geometric dimensions of the ridge waveguide. The phase-matching wavelength and conversion efficiencies versus the geometric dimensions in the modal phase-matching process are investigated. We also analyze the thermal-tuning ability of the present modal phase matching scheme. Our results show that highly efficient second harmonic generation can be realized by the modal phase matching in the double-layered thin film lithium niobate ridge waveguide.

High‐Performance Electro‐Optic Modulator on Silicon Nitride Platform with Heterogeneous Integration of Lithium Niobate

AbstractSilicon nitride (SiN) emerges as an important platform for ultralow loss photonic integrations with complementary metal‐oxide‐semiconductor compatibility. However, active devices, such as modulators, are difficult to realize on pure SiN due to the lack of any electro‐optic (EO) properties of the material. Here, an SiN and lithium niobate (LN) heterogenous integration platform supporting high‐performance EO modulators on SiN waveguide circuits is introduced. An efficient evanescent coupling structure is realized for low‐loss light transitions between the SiN waveguide and the LN ridge waveguide with a measured mode transition loss of only 0.4 dB. Based on this heterogeneous platform, an EO Mach–Zender interference modulator on SiN is built with unprecedented loss, efficiency, and bandwidth performances. A half‐wave voltage of 4.3 V with a modulation bandwidth of 37 GHz and an overall insertion loss of 1 dB is measured for a 7‐mm long device. Data transmission up to 128 Gb s−1 with a bit‐error‐rate of <2.4 × 10‐4 is also demonstrated.

Broadband telecom photon pairs from a fiber-integrated PPLN ridge waveguide.

We demonstrate a spectrally correlated photon-pair source at telecom wavelengths (spanning across the S-, C-, and L-bands), based on type-0 spontaneous parametric downconversion (SPDC) in a fiber-coupled Zn-indiffused MgO doped periodically poled lithium niobate (PPLN) ridge waveguide. Modal analysis of the waveguide performed through numerical finite element method (FEM) simulation indicates that device temperature can be used to dramatically vary and control the emission spectrum. Efficient photon-pair generation is measured over a broad wavelength range from ∼1520 - 1580 nm [full width at half maximum (FWHM) > 45 nm] with a coincidence-to-accidental ratio (CAR) as high as ∼668 and spectral brightness ∼2.5 × 107 pairs/s/mW/nm. Such sources can be employed in wavelength division multiplexed (WDM) quantum key distribution (QKD) over existing fiber-optic networks.

Low-loss fiber grating coupler on thin film lithium niobate platform

A grating coupler with a high coupling efficiency and low back reflections is designed and demonstrated on the thin film lithium niobate platform, which facilitates an efficient interface between a lithium niobate ridge waveguide and a standard single mode fiber. The excellent performances of the present grating coupler are enabled by a cavity-assisted grating structure and a top metal mirror, even though a uniform grating is adopted as the diffractive element. Experimentally, a coupling loss of −0.89 dB at 1552 nm is demonstrated with a 1-dB bandwidth of 45 nm. Low back reflections of <−16.5 dB to the waveguide and <−13.7 dB to the fiber are also achieved from 1536 to 1579 nm.

Second and cascaded harmonic generation of pulsed laser in a lithium niobate on insulator ridge waveguide.

Nonlinear crystalline ridge waveguides, e.g., lithium niobate-on-insulator ridge waveguides, feature high index contrast and strong optical confinement, thus dramatically enhancing nonlinear interaction and facilitating various nonlinear effects. Here, we experimentally demonstrate efficient second-harmonic generation (SHG) and cascaded fourth-harmonic generation (FHG) in a periodically poled lithium niobate (PPLN) ridge waveguide pumped with pulsed laser at the quasi-phase matching (QPM) wavelength, as well as simultaneous SHG and cascaded third-harmonic generation (THG) waves when pumped at the non-QPM wavelength. Furthermore, the ridge waveguide achieves an efficient single-pass SHG conversion efficiency of picosecond pulsed laser at ∼62%. These results may be beneficial for on-chip nonlinear frequency conversion.

Watt-level SHG in undoped high step-index PPLN ridge waveguides

Nonlinear quadratic waveguides are key components to obtain efficient frequency conversion. In this paper we present the performances of highly multimode periodically poled lithium niobate (PPLN) ridge waveguides for high power CW SHG are presented. We report the generation of 1 W of second harmonic on the fundamental guided mode with a conversion efficiency of 56% at telecom wavelengths. A stable nonlinear process is obtained despite use of an undoped congruent LiNbO3 crystal. The input damage threshold of the ridge waveguide is found to set the maximum usable power.

Metal based grating coupler on a thin-film lithium niobate waveguide.

Thin-film lithium niobate (LN) has been proved to be an excellent platform for building compact active and nonlinear photonic components on a chip. The coupling of a sub-micron sized LN waveguide and a single-mode fiber remains as one challenging issue. An efficient grating coupler made of Au stripes on an LN ridge waveguide is demonstrated here. The fabrication of the grating is convenient, using just a standard lift-off process of metal films. The peak coupling efficiency of an optimized structure reaches 50.4%, i.e., -3 dB coupling loss, at 1.55 µm wavelength for the fundamental transverse-electrical mode, where the 1-dB coupling bandwidth is 58 nm. Experimentally, fabricated devices, with buried oxide layer thicknesses slightly off the optimal values, exhibit coupling efficiencies of 43.8% and 33.7% for 400 nm and 600 nm thick LN layers.

SPDC photon pairs using a spatially anti-symmetric pump beam in a ppLN ridge waveguide

In this paper, we study the possible parametric down-conversion processes in a type II phase-matched, Lithium Niobate ridge waveguide, designed to generate photon pairs in the telecommunication range. A quantum analysis of spontaneous parametric down-conversion (SPDC), first, with a pulsed Gaussian pump beam and second, with a pulsed, spatially anti-symmetric Hermite-Gaussian HG (1,0) pump beam predict the possible down conversion processes in each case. In case of the former, degenerate photon pairs are emitted at 1550 nm with the highest efficiency in the fundamental waveguide mode. While, in case of the latter, non-degenerate photon pairs in different higher-order spatial modes are generated. The joint spectral amplitude (JSA) analysis of these processes, prove that the generated photons pairs having orthogonal polarizations are negatively correlated. With multiple degrees of freedom, like polarization and spatial modes, such photons can be further harnessed towards modal-entangled and hyper-entangled photons for quantum information applications. This study involving the JSA is one of the first kinds, especially, to show the possibility of photon pairs generated in different spatial modes and polarization, after being incident with a spatially anti-symmetric pump beam in a ridge waveguide scenario.

UV-written grating couplers on thin-film lithium niobate ridge waveguides.

Grating couplers on thin-film lithium niobate ridge waveguides were designed and fabricated using UV-laser ablation. The calculated coupling efficiency with a sinusoidal grating can be as large as 53% in a 0.5 µm thin film. The maximum grating depth we fabricated was 130nm, limiting the coupling efficiency to a theoretical value of 18%. We fabricated grating couplers on adhered ridge waveguides of 20 µm thickness. Coupling light to waveguides on thin-film lithium niobate is still challenging, and here we present a fast, cheap and reliable fabrication alternative. It will benefit the on-chip testing of integrated components developed on this novel and promising material platform.

Integrated electro-optic modulators in x-cut lithium niobate thin film

Integrated optics is poised to revolutionize several data communication applications. The development of high performance electro-optic modulators is essential for the technology to be viable. In this paper, single-mode electro-optic modulators in x-cut lithium niobate thin film are designed, simulated, and analyzed. The single-mode conditions of lithium niobate ridge waveguides are analyzed in detail. The design parameters of Y-branch and separation distances between electrodes and ridge waveguides are optimized. The half-wave voltage of the electro-optic modulator with device lengths of 10 mm is determined. The half-wave voltage-length product is about 2.2 V·cm indicating the efficient electric-optical modulation. This study is helpful for understand of electro-optic modulator structures in lithium niobate thin film, as well as for the fabrication of high-performance and multifunctional electro-optic modulation devices.

Spectral noise in frequency conversion from the visible to the telecommunication C-band.

We report a detailed study of the noise properties of a visible-to-telecom photon frequency converter based on difference frequency generation (DFG). The device converts 580 nm photons to 1541 nm using a strong pump laser at 930 nm, in a periodically poled lithium niobate ridge waveguide. The converter reaches a maximum device efficiency of 46 % (internal efficiency of 67%) at a pump power of 250 mW. The noise produced by the pump laser is investigated in detail by recording the noise spectra both in the telecom and visible regimes and measuring the power dependence of the noise rates. The noise spectrum in the telecom is very broadband, as expected from previous work on similar DFG converters. However, we also observe several narrow dips in the telecom spectrum, with corresponding peaks appearing in the 580 nm noise spectrum. These features are explained by sum frequency generation of the telecom noise at wavelengths given by the phase-matching condition of different spatial modes in the waveguide. The proposed noise model is in good agreement with all the measured data, including the power dependence of the noise rates, both in the visible and telecom regimes. These results are applicable to the class of DFG converters where the pump laser wavelength is in between the input and target wavelength.

Analysis of Waveguides on Lithium Niobate Thin Films

Waveguides formed by etching, proton-exchange (PE), and strip-loaded on single-crystal lithium niobate (LN) thin film were designed and simulated by a full-vectorial finite difference method. The single-mode condition, optical power distribution, and bending loss of these kinds of waveguides were studied and compared systematically. For the PE waveguide, the optical power distributed in LN layer had negligible change with the increase of PE thickness. For the strip-loaded waveguide, the relationships between optical power distribution in LN layer and waveguide thickness were different for quasi-TE (q-TE) and quasi-TM (q-TM) modes. The bending loss would decrease with the increase of bending radius. There was a bending loss caused by the electromagnetic field leakage when the neff of q-TM waveguide was smaller than that of nearby TE planar waveguide. LN ridge waveguides possessed a low bending loss even at a relatively small bending radius. This study is helpful for the understanding of waveguide structures as well as for the optimization and the fabrication of high-density integrated optical components.

Ductile dicing of LiNbO 3 ridge waveguide facets to achieve 0.29 nm surface roughness in single process step

A single-step ductile dicing process capable of manufacturing optical quality facets in lithium niobate (LiNbO3) ridge waveguides with an average surface roughness of 0.29 nm is reported. This result is comparable with surface roughnesses achieved by lapping and polishing and represents an order of magnitude improvement over the prior state of the art in LiNbO3 waveguide facet dicing.

Reduced pulse energy for frequency comb offset stabilization with a dual-pitch periodically poled lithium niobate ridge waveguide

The pulse energy for stabilizing the carrier-envelop offset frequency of an Er-doped fiber laser was reduced by a dual-pitch (DP-) periodically poled lithium niobate (PPLN) ridge waveguide implemented in a 2f-to-3f self-referencing interferometer (SRI). The pulse energy requirement was less than half that for a single-pitch PPLN ridge waveguide implemented in an f-to-2f SRI. We also found that environmental noise could be reduced by adjusting the pulse energy for frequency stabilization with the DP-PPLN ridge waveguide, as estimated from the phase noise of an out-of-loop interferometer.

Analysis of influence of wall defect in lithium niobate ridge waveguide

Analysis of influence of wall defect in lithium niobate ridge waveguide

Second-harmonic generation in single-mode integrated waveguides based on mode-shape modulation

Second-harmonic generation is demonstrated using grating-assisted quasi-phase matching, based on waveguide-width modulation or mode-shape modulation. Applicable to any thin-film integrated second-order nonlinear waveguide, the technique is demonstrated in compact lithium niobate ridge waveguides. Fabricated devices are characterized with pulsed-pumping in the near-infrared, showing second-harmonic generation at a signal wavelength of 784 nm and propagation loss of 1 dB/cm.

Supercontinuum Generation in Lithium Niobate Ridge Waveguides Fabricated by Proton Exchange and Ion Beam Enhanced Etching**Supported by the National Natural Science Foundation of China under Grant Nos 61575129 and 11375105, the Postdoctoral Science Foundation of China under Grant No 2016M602511, the Shenzhen Science and Technology Planning under Grant No JCYJ20160422142912923, and the State Key Laboratory of Nuclear Physics and Technology,

We report on the fabrication of the 10-mm-long lithium niobate ridge waveguide and its supercontinuum generation at near-visible wavelengths (around 800 nm). The waveguides are fabricated by a combination of MeV copper ion implantation followed by wet etching in a proton exchanged lithium niobate planar waveguide. Using a mode-locked Ti:sapphire laser with a central wavelength of 800 nm, the generated broadest supercontinuum through the ridge waveguides spans 302 nm (at −30 dB points), from 693 to 995 nm. Temporal coherence properties of the supercontinuum are experimentally studied by a Michelson interferometer and the coherence length of the broadest supercontinuum is measured to be 5.2μm. Our results offer potential for a compact and integrated supercontinuum source for applications including bio-imaging, spectroscopy and optical communication.

Grating Coupler for an On-Chip Lithium Niobate Ridge Waveguide

We report simulation and fabrication of a grating coupler for coupling of light between an on-chip lithium niobate ridge waveguide and an optical fiber. A grating coupler with an insertion loss of less than 10 dB for C-band frequencies (1530–1565 nm) was achieved.