Liquid Research Articles

A Novel 3D-Printed Gravity-Independent Air-Eliminating Filter for Rapid Intravenous Infusions.

INTRODUCTION: The absence of a consistent downward G vector can make separation of gases from liquids challenging, such as in field medicine without stable upright equipment or during spaceflight. This limits the use of medical equipment and procedures like administration of intravenous (IV) fluids in microgravity and can make field medicine hazardous. Administering IV fluids and medications in microgravity requires a technique to separate air from the liquid phase. Current commercial filters for separation of gases are incompatible with high flow and blood. We present a novel filter designed to provide adequate air clearance without a consistent downward G vector.METHODS: Inline air-eliminating filters were designed for use with IV fluid tubing in microgravity using computer-aided design software and printed using nylon 12 on an EOS Selective Laser Sintering 3D printer. A 0.2-μm membrane filter was adhered around a central, hollow pillar with external spiral baffles allowing separation and venting of air from the fluid. Results were compared against commercially available inline air-eliminating filters.RESULTS: The 3D-printed filters outperformed the commercial filters in both percentage of air removed and flow rates. The centrifugal, baffled filter had flow rates that far exceeded the commercial filters during rapid transfusion.DISCUSSION: IV fluid administration is an often underappreciated and a necessary basic requirement for medical treatment. An air-eliminating filter compatible with blood and rapid transfusion was developed and validated with crystalloid solutions to allow the successful administration of IV fluid and medication without a consistent downward G vector.Formanek A, Townsend J, Ottensmeyer MP, Kamine TH. A novel 3D-printed gravity-independent air-eliminating filter for rapid intravenous infusions. Aerosp Med Hum Perform. 2024; 95(6):327-332.

Direct evidence of gas flushing oil in deep reservoirs: Insight from integrated fluid inclusion analyses

Gas flushing of oil has been proposed as an essential process for forming some condensate gas reservoirs based on laboratory experiments and modeling but such a process has rarely been documented in subsurface reservoirs. Here, we report a unique type of yellow-ringed oil inclusions (YROIs) discovered from a deep reservoir in the Kuqa Foreland Basin, Western China that recorded the gas flushing of oil process in the subsurface. The occurrence, composition, phase state and PVT conditions of YROIs during trapping were investigated using a suite of fluid inclusion analytical methods including fluid inclusion petrography, microthermometry, fluorescence spectroscopy, PVT modeling and molecular composition analysis.YROIs found in the reservoir are three-phase (solid–liquid-vapor) fluid inclusions at room temperature with solid rings of 2–3 μm thickness and estimated volume percentages varying between 5 % and 15 %. When heated the solid ring starts to melt at around 46 °C and homogenized with the liquid phase at or above their corresponding homogenization temperatures of coeval aqueous inclusions. YROIs have fluorescence spectral peaks between 530 nm and 550 nm and an elevated spectral shoulder around 650 nm when measured at room temperature; but most spectra show a distinct “blue shift” and an absence of the 650 nm shoulder when measured at their homogenization temperatures. Some YROIs with thick yellow rings show dual spectral peaks at 570 nm and 630 nm at room temperature and their spectral peaks do not change when remeasured at their homogenization temperatures. Molecular compositions derived from synchronous fluorescence spectra and GC-MS analysis suggest that the compositions of YROIs are rich in polyaromatic compounds. PVT modeling indicates that YROIs were trapped under high pressure conditions with a pressure exceeding 50 % of the corresponding hydrostatic pressure.YROIs are interpreted to have been trapped under an elevated temperature and overpressure condition (around 110 °C and 60 MPa) relating to an intensive (wet) gas flushing of an early-charged wax-rich oil. When light hydrocarbon components in the reservoir oil were partially removed by gas, the wax/resin components rich in polyaromatic hydrocarbon compounds may precipitate due to physio-chemical fractionation. YROIs were entrapped in subsurface from a heterogeneous hydrocarbon fluid containing variable amounts of wax/resin colloids, which subsequently coalesce to form solid rings adhering to the inner wall of oil inclusions at room temperature. The presence of yellow-ringed oil inclusions in a reservoir may be indicative of a rapid gas flushing of waxy oil under high pressure, and their minimum homogenization temperature may approximate their trapping temperature.

CO2 Joule-Thomson effect: application on premium connections for CCS well

CCS (Carbon Capture and Storage) is a major technology aiming to reduce greenhouse gases and reduce carbon footprint. In these applications, Oil Country Tubular Goods (OCTG) and associated premium connections are used to inject industrial CO2 into stable geological formations such as depleted oil and gas fields or saline aquifers, in liquid or dense phase to permanently store it. While current standards (API RP 5C5, ISO 13679) allow qualification of premium connections for Oil & Gas application, no standard exists for CCS applications. In that frame, a new test methodology was developed to evaluate the impact of Joule-Thomson effect on premium connection, in the scenario of a CO2 blow-out and intermittent operation of the injection wells, such as shut-in of the subsurface safety valve (SSSV) or injection phase. To confirm that premium connections remain tight and safe after being exposed to a rapid depressurization of CO2, they have been physically tested in a horizontal load frame. The test consisted in the filling of the sample with CO2 up to a minimum of 100 bar and a temperature below 30°C to ensure liquid state, or above 32°C to ensure supercritical state inside the sample, and then depressurizing the sample through an orifice of 2 or 4 mm until complete drop of pressure. Minimum measured temperature on outer pipe wall reached around -50°C before dry ice CO2 formation. Maximum measured gradient of temperature observed was around 70°C. No leakage nor connection damages were observed during the pressure release sequences. Sealability was then confirmed during the internal pressure and external pressure test performed afterwards.

Temperature dependence of photoluminescence kinetics and scintillation properties of LuY2(Al5-xScx)O12:Ce (x = 1, 1.5, 2) garnet single-crystalline films

The temperature dependence of photoluminescence (PL) kinetics and scintillation properties were investigated in LuY2(Al5-xScx)O12:Ce (x = 1, 1.5, 2) garnet single-crystalline films grown by the isothermal liquid phase epitaxy method. With the increase of Sc content, the Ce3+ 5d1 level was shifted to higher energy while the Ce3+ 5d2 level was shifted to lower energy due to the decrease in crystal field splitting of the 5d levels. Activation energy of thermal quenching, determined from temperature-dependent PL decay times, decreased with increasing Sc content. At room temperature, the decrease of light yield (LY) value with increasing Sc content is caused by the thermal ionization process. LuY2(Al4Sc)O12:Ce showed a LY value of 510 photons/MeV when excited by 5.5 MeV α-particles, which is ∼21 % larger than that of Lu2Y(Al4Sc)O12:Ce due to a smaller bandgap Eg of the former.

Технология изготовления образцов из композитных материалов для проведения лабораторных испытаний

Based on the accumulated experience of the staff of the Institute of Marine Technologies, Energy and Transport of the Astrakhan State Technical University, the development of the production of various parts of ship hulls, elements of main and auxiliary power plants, including various fasteners and stanchions, using additive technology and other methods of forming composite materials has begun. During the implementation of the developed direction, issues arise of reducing the cost, weight of manufactured parts and improving the characteristics of sound absorption, sound insulation, vibration isolation, etc. Despite the fact that adhesives based on epoxy or polyester resin, according to technical documentation, are fast-curing adhesives, they are not applicable for the production of products using three-dimensional printing technologies. for several reasons. The factors preventing the use of materials for the production of such parts are listed: the minimum curing time of one layer of glue under optimal conditions is from one and a half hours or more, which significantly increases the interlayer time interval; the glue layer is not a self-supporting structure due to the fact that it is in a liquid state during the induction period; products made of this adhesive without reinforcement cannot withstand the required dynamic loads. In the process of experimental studies, a number of formulations based on polyester resin with different fillers were obtained, which have the necessary consistency to apply layers on top of the previous one without waiting for curing, and also contain the necessary amount of reinforcing material and other fillers required to solve problems related to vibration isolation and sound insulation.

The property and function of proteins undergoing liquid-liquid phase separation in plants.

A wide variety of membrane-less organelles in cells play an essential role in regulating gene expression, RNA processing, plant growth and development, and helping organisms cope with changing external environments. In biology, liquid-liquid phase separation (LLPS) usually refers to a reversible process in which one or more specific molecular components are spontaneously separated from the bulk environment, producing two distinct liquid phases: concentrated and dilute. LLPSmay be a powerful cellular compartmentalisation mechanism whereby biocondensates formed via LLPS when biomolecules exceed critical or saturating concentrations in the environment where they are found will be generated. It has been widely used to explain the formation of membrane-less organelles in organisms. LLPS studies in the context of plant physiology are now widespread, but most of the research is still focused on non-plant systems; the study of phase separation in plants needs to be more thorough. Proteins and nucleic acids are the main components involved in LLPS. This review summarises the specific features and properties of biomolecules undergoing LLPS in plants. We describe in detail these biomolecules' structural characteristics, the mechanism of formation of condensates, and the functions of these condensates. Finally, We summarised the phase separation mechanisms in plant growth, development, and stress adaptation.

Small-scale hydrological patterns in a Siberian permafrost ecosystem affected by drainage

Abstract. Climate warming and associated accelerated permafrost thaw in the Arctic lead to a shift in landscape patterns, hydrologic conditions, and release of carbon. In this context, the lateral transport of carbon and shifts therein following thaw remain poorly understood. Crucial hydrologic factors affecting the lateral distribution of carbon include the depth of the saturated zone above the permafrost table with respect to changes in water table and thaw depth and the connectivity of water-saturated zones. Landscape conditions are expected to change in the future due to rising temperatures and polygonal or flat floodplain Arctic tundra areas in various states of degradation; hydrologic conditions will also change. This study is focused on an experimental site near Chersky, northeast Siberia, where a drainage ditch was constructed in 2004 to simulate landscape degradation features that result in drier soil conditions and channeled water flow. We compared water levels and thaw depths in the drained area (dry soil conditions) with those in an adjacent control area (wet soil conditions). We also identified the sources of water at the site via stable water isotope analysis. We found substantial spatiotemporal changes in the water conditions at the drained site: (i) lower water tables resulting in drier soil conditions, (ii) quicker water flow through drier areas, (iii) larger saturation zones in wetter areas, and (iv) a higher proportion of permafrost meltwater in the liquid phase towards the end of the growing season. These findings suggest decreased lateral connectivity throughout the drained area. Shifts in hydraulic connectivity in combination with a shift in vegetation abundance and water sources may impact carbon sources and sinks as well as transport pathways. Identifying lateral transport patterns in areas with degrading permafrost is therefore crucial.

Understanding the Ageing Processes of Electrolytes in Aqueous Magnesium Batteries Using Radiation Chemistry

Manufacturing aqueous batteries based on the magnesium cations is an important step towards more sustainable and safer energy storage solutions. Thus, it is important to understand how these systems age and which species are formed throughout numerous charge/discharge cycles. To this end, we have used radiolysis to induce accelerated aging in concentrated solutions of magnesium bistriflimide Mg(TFSI)2 (also called “water‐in‐salt electrolytes” or WISEs). We demonstrate in this work that the degradation products formed, whether in the gas or liquid phase, are very similar to those formed in concentrated LiTFSI aqueous solutions. In fact, the behavior under ionizing radiation is driven by the anion/water molar ratio regardless of whether the cation is Li+ or Mg2+. This is because both cations are non‐reactive, and the bond strengths in the TFSI‐ anion do not vary with the nature of the cation. Reaction mechanisms are proposed to explain the formation of several species under ionizing radiation.

Existence of density inhomogeneity of liquid Te associated with liquid–liquid phase transition

We performed small-angle x-ray scattering measurements of liquid Te using a synchrotron radiation facility and observed maximum scattering intensity near 620 K in the supercooled region (melting temperature 723 K). This indicates that density inhomogeneity exists in liquid Te, and the fact that this temperature coincides with the temperature at which the specific heat, sound velocity, and thermal expansion coefficient reach their maxima means that this density inhomogeneity is the cause of these thermodynamic anomalies. The thermodynamic anomalies in liquid Te had already been shown in the 1980s to be comprehensively explained by the inhomogeneity associated with the continuous liquid–liquid phase transition (LLT), but direct experimental evidence for the existence of the inhomogeneity had not been obtained. The present results, together with those already obtained for mixture systems (Te–Se, Te–Ge), indicate the existence of inhomogeneity associated with LLT in liquid Te systems, and strongly support the model. Recently, similar maximum scattering intensity has also been observed in supercooled liquid water, which exhibits thermodynamic anomalies similar to those of Te, indicating the universality of the inhomogeneous model or LLT scenario to explain the thermodynamics of such ‘anomalous liquids’. Further development of the LLT scenario is expected in near future.

Inhibiting the Accretion in the Coal-Fired Rotary Kiln of High-Silica Iron Ore Pellets Application by Reducing Fines Generation and Liquid Phase Formation

Inhibiting the Accretion in the Coal-Fired Rotary Kiln of High-Silica Iron Ore Pellets Application by Reducing Fines Generation and Liquid Phase Formation

Dynamic response of a pipe with geometrical restriction subjected to gas-liquid internal flow

Due to the potential hazard of deepwater oil exploration, the Brazilian industry has an ever-increasing concern for reliability during hydrocarbon production. A major source of concern is mechanical failure in devices, such as safety valves, which can fail without warning, putting both the operation and the environment at risk. A possible reason for malfunction and failure could be the permanent occurrence of vibrations induced by internal two-phase flow during the extraction of fluids from the well. An experimental campaign is proposed to better understand these phenomena. Twenty two-phase flow conditions were tested, with superficial velocities ranging from 0.1 m/s to 2.0 m/s for water, and 0.33 m/s to 7.47 m/s for compressed air. The experiments were carried out in a restricted pipe and a pipe without any restriction to evaluate and compare the vibrations produced by two-phase flow (2-FIV). Three accelerometers positioned downstream of the restriction were used to collect vibrational amplitude spectral density data, 2-D acceleration magnitudes, and RMS values of acceleration. Among the main findings are the roles played by the gas volumetric fraction and the mixture velocity, which strongly influence the vibrational amplitude of both tubes, and the observation that the gas phase is the main responsible for vibrational amplitudes at low frequencies, while the liquid phase acts mainly at high frequencies. Furthermore, the flow pattern is also considered a key feature in determining the vibration level, as 20- and 12-fold increments have been observed for the same volumetric fraction when comparing elongated bubbles and severe slug patterns. Finally, it was demonstrated that the presence of an internal restriction strongly influences the structural response.

Current Trends in Liquid Crystal Polymers and Their Applications: A Review

Liquid crystal polymers (LCPs) are now highly focused by researchers due to their improved thermal properties, mechanical strength, excellent dielectric strength, resistance to solvents, better dimensional stability, and gas barrier properties. LCPs can be used in valuable widespread applications such as energy storage, high-performance polymer fibers, actuators, information technologies, surface modification, shape memory materials, data storage, fiber optics, the medical field, electrical or electronics devices, aircraft, chemical, domestic equipment, ultra-high-strength fibers, biosensing, advanced communication systems, satellite systems, biosensing, bio-oscillators, and bioprocess monitoring. LCPs can self-assemble into different liquid crystalline phases like nematic, cholesteric, smectic, and columnar phases. The self-assembling structures of LCPs can be affected by the chemical and structural structures of the backbone of the polymeric material, nearby alkyl tails, mesogenic units, flexible spacers, etc. Depending on the mesogenic units in their molecular architecture, LCPs are basically classified into various categories, such as crosslinked, main chain, and sidechain. Again, they are also classified as cholesteric, nematic, and smectic mesophases. This paper provides a fundamental understanding, an informative overview, and details of structural aspects, properties, classification, commercial aspects, and applications of LCPs.

Thermodynamics assessment of the Erbium-Ruthenium system by combining the Ab-initio and CALPHAD methods

ABSTRACT In the present study, the erbium-ruthenium system was optimised using the CALPHAD approach. The thermodynamic properties and the phase diagram were evaluated. The enthalpies of formation of the intermetallic compounds for the binary system Er-Ru were calculated by ab- initio methods. The liquid phase was treated with the exponential model, while a solution model was applied to represent the HCP (Er, Ru) solid solution. The five intermetallic compounds Er3Ru, Er5Ru2, Er3Ru2, ErRu2, and Er44Ru25 were considered as stoichiometric compounds. The calculations are in good agreement with the phase diagram information and experimental thermodynamic values documented in the literature.

A Semi-implicit Finite Volume Scheme for Incompressible Two-Phase Flows

AbstractThis paper presents a mass and momentum conservative semi-implicit finite volume (FV) scheme for complex non-hydrostatic free surface flows, interacting with moving solid obstacles. A simplified incompressible Baer-Nunziato type model is considered for two-phase flows containing a liquid phase, a solid phase, and the surrounding void. According to the so-called diffuse interface approach, the different phases and consequently the void are described by means of a scalar volume fraction function for each phase. In our numerical scheme, the dynamics of the liquid phase and the motion of the solid are decoupled. The solid is assumed to be a moving rigid body, whose motion is prescribed. Only after the advection of the solid volume fraction, the dynamics of the liquid phase is considered. As usual in semi-implicit schemes, we employ staggered Cartesian control volumes and treat the nonlinear convective terms explicitly, while the pressure terms are treated implicitly. The non-conservative products arising in the transport equation for the solid volume fraction are treated by a path-conservative approach. The resulting semi-implicit FV discretization of the mass and momentum equations leads to a mildly nonlinear system for the pressure which can be efficiently solved with a nested Newton-type technique. The time step size is only limited by the velocities of the two phases contained in the domain, and not by the gravity wave speed nor by the stiff algebraic relaxation source term, which requires an implicit discretization. The resulting semi-implicit algorithm is first validated on a set of classical incompressible Navier-Stokes test problems and later also adds a fixed and moving solid phase.

Mechanism of displacement gas kick in horizontal well drilling into deep fractured gas reservoir

The risk of well control is high when displacement gas kick occurs in the deep fractured reservoir, and improper handling can easily lead to blowout, which will seriously affect the deep well drilling. Using Fluent software, a simulation model was constructed to depict the interaction of a horizontal well with vertical fractures. The displacement gas kick process was simulated in horizontal well under formation temperature and pressure conditions. An analysis was conducted to assess the impact of fracture width, quantity, as well as the viscosity and density of drilling fluid on the process of gas-liquid displacement. It further compared the effectiveness of three measures in counteracting displacement gas kick: applying back pressure at the wellhead, altering the viscosity and density of the drilling fluid. New findings suggest that the gas-liquid interface within the fracture exhibits a funnel-like shape, where the gas and liquid phases are layered in the annulus and manifest in a streak-like pattern. Fracture width, quantity, and drilling fluid density promote displacement, while drilling fluid viscosity inhibits the displacement. Different from vertical wells, in horizontal wells, displacement gas kick mainly appears in the underbalanced interval. The fracture width primarily determines the size of the displacement window, while the density and viscosity of the drilling fluid exert lesser influence. Horizontal wells are highly sensitive to variations in external conditions when it comes to displacement gas kick. Therefore, enhancing the wellhead back pressure is advisable to address the displacement gas kick in horizontal wells.

An Integrative Chemical Recycling Approach for Catalytic Oxidation of Epoxy Resin and in situ Separation of Degraded Products

AbstractAlthough many approaches have been proposed to recycling waste epoxy resin (EP), the separation of mixed degraded products remains a challenge due to their similar structures. To address this, we present a catalytic oxidation strategy that enables mild degradation of EP and in situ separation of degraded products through supramolecular interactions. The oxidative degradation relies on FeIV=O radicals with strong oxidizing properties, which are generated from the electron transfer of FeCl2 with reaction reagents. As the FeIV=O radicals attacked the C−N bonds of EP, EP was broken into fragments rich in active functional groups. Meanwhile, the FeIV=O radicals were reduced to iron ions that can coordinate with the carboxyl groups on the fragments. As a result, the degraded products with different carboxyl content can be effortlessly separated into liquid and solid phase by coordinating with the catalyst. The success of this work lays the foundation for high‐value application of degraded products and provides new design ideas for recycling waste plastics with complex compositions.

Experimental study on effect of deformation temperature on mechanical and biological activities of Ti-6Al-7Nb titanium alloy

Abstract Titanium alloy plays a crucial role in biomedical applications, particularly in the field of medical implants. One of the most significant advantages of Titanium alloy is its excellent biocompatibility. Eventhough, it offered excellent behaviour, at elevated temperature, titanium alloys may experience softening, which limits their application in environments with higher operating temperatures. In this investigation, hot tensile and biological behaviour of the Ti-6Al-7Nb under different operating temperatures (300oC, 400oC, 500oC and 600oC) is studied. The biological behaviour of the deformed Ti-6Al-7Nb titanium alloy treated with simulated body fluid is studied. The microstructure and phase transformation of deformed titanium alloy is evaluated using scanning electron microscope (SEM) and X-Ray diffraction (XRD) respectively. It was revealed that at temperature of 600oC, the mobility of molecules at the interface between the solid and liquid phases increases. This enhanced mobility can lead to better wetting of the solid surface by the liquid, resulting in a decrease in the contact angle. Elevated temperature facilitates improved grain development, recrystallization, and mobility. Coarser grains could result from deformation at temperature higher than 600°C. It was concluded that the Ti-6Al-7Nb titanium alloy deformed with 600oC showed the improvement in contact angle of 42±2o and biocompatibility.

Numerical Investigation of Heat Transfer Characteristics of Trapezoidal Fin Phase Change Thermal Energy Storage Unit

Abstract: In order to enhance the heat transfer performance of a phase change thermal energy storage unit, the effects of trapezoidal fins of different sizes and arrangement modes were studied by numerical simulation in the heat storage and release processes. The optimal enhancement solution was obtained by comparing the temperature distribution, instantaneous liquid-phase ratio, solid–liquid phase diagram and comprehensive heat storage and release performance of the thermal energy storage unit under different fin sizes. During the heat storage process, the results show that when the ratio of the length of the upper and lower base of the trapezoid h1/h2 is 1:9, the heat storage time is shortened by 9.03% and 18.21% compared with h1/h2 = 3:7 and 5:5, respectively. During the heat release process, the optimal heat transfer effect is achieved when h1/h2 = 5:5. To further improve the heat transfer effects, the energy storage unit is placed upside down; then, the least time is achieved when h1/h2 = 2:8. When heat storage and release are considered together, the energy storage unit with h1/h2 = 2:8 takes the shortest time to melt in upright placement and then to solidify in upside-down placement.

Rheological Behavior Features of Feedstocks with a Two-Component Wax–Polyolefin Binder Compared to Analogs Based on Polyoxymethylene

Despite the large number of studies devoted to different compositions of polymer binders for PIM technology, the actual task is still a comparative analysis of the properties of different types of binders to determine their advantages and disadvantages and optimize the compositions used. In this regard, this study aims at the identification and comparative analysis of the rheological properties of the most demanded feedstocks with binders based on polyoxymethylene and a wax–polyolefin mixture under the condition of using identical steel powder filler. The rate of change in the volume fraction of the liquid phase of the binder in the compared feedstocks with temperature change was determined by the calculation–experimental method. As shown, the temperature dependence of the viscosity of feedstocks with a binder based on a polymer blend depends on factors with variable power, i.e., the viscosity change with temperature occurs by different mechanisms with their relaxation spectra. Thus, the principle of temperature–time superposition for feedstocks with multicomponent binders is not applicable, and the study of the viscosity of such materials should involve a wide range of shear rates and temperatures using experimental methods. Capillary rheometry was used to measure the flow curves of feedstocks based on polyoxymethylene and wax–polyolefin binders. The analysis of flow curves of feedstocks showed that feedstocks with a binder of solution–thermal type of debinding have significantly lower viscosity, which is an advantage for molding thin-walled products. However, their difference of 1.5 times sensitivity to the shear rate gradient leads to their lower resistance to “jets” and liquation of components because of shear rate gradients when molding products with elements of different cross-sectional areas.

Percolation transition and bimodal density distribution in hydrogen fluoride.

Hydrogen-bond networks in associating fluids can be extremely robust and characterize the topological properties of the liquid phase, as in the case of water, over its whole domain of stability and beyond. Here, we report on molecular dynamics simulations of hydrogen fluoride (HF), one of the strongest hydrogen-bonding molecules. HF has more limited connectivity than water but can still create long, dynamic chains, setting it apart from most other small molecular liquids. Our simulation results provide robust evidence of a second-order percolation transition of HF's hydrogen bond network occurring below the critical point. This behavior is remarkable as it underlines the presence of two different cohesive mechanisms in liquid HF, one at low temperatures characterized by a spanning network of long, entangled hydrogen-bonded polymers, as opposed to short oligomers bound by the dispersion interaction above the percolation threshold. This second-order phase transition underlines the presence of marked structural heterogeneity in the fluid, which we found in the form of two liquid populations with distinct local densities.