Light Intensity Modulation Research Articles

Analysis of the Performance of WDM-CDM Bragg Grating Interrogation System With High-Contrast Grating VCSEL

This article shows a novel approach for Bragg gratings interrogation, based on vertical-cavity surface-emitting laser with high-contrast grating cavity. It is shown that with such a light source, one may achieve simultaneous wavelength sweeping together with output light intensity modulation enabled by a single element. In turn, it allows for designing a two-dimensional (time and wavelength) Bragg grating interrogation scheme. The article consists of analytical deliberations that determine the limiting factors of such an interrogation unit, i.e. interrogation speed and size of the sensing network for given Bragg grating reflectivity, expressed in the form of signal-to-noise ratio. Moreover, an experimental and numerical proof of concept of the sensing unit consisting of fiber Bragg grating sensors with an interrogation speed of 1 kHz and the use of code division multiplexing is also presented.

Liquid crystal elastomer composite-based photo-oscillator for microrobots

In recent years, photoactive materials have attracted extensive interest in microrobots for their attractive abilities of untethered and tunable control with light. Conventional photo-oscillators based on Azo-containing liquid crystal network require complex surface alignment techniques and light sources with specific wavelengths and polarity, which limits their application in controlled autonomy. Here, we report a facile strategy to create self-oscillating microrobots powered and controlled by a wide spectrum of constant light. The oscillators are composed of a layer of candle soot (CS)-containing liquid crystal elastomer (LCE) attached to a layer of polydimethylsiloxane (PDMS). The strip-shaped oscillators with one end fixed can execute self-sustained oscillation through a self-shadowing mechanism. LCEs with CS as an excellent photo-absorber provides superior photothermal actuation, while PDMS with low viscoelasticity accelerates the actuation-recovery cycle of the oscillator. Our LCE composite photo-oscillators show tunable frequencies and amplitudes by structural and light intensity modulation, showing potential for autonomous soft robotic applications.

Dissipative coupling-induced phonon lasing

Phonon lasers, as the counterpart of photonic lasers, have been intensively studied in a large variety of systems; however, (all) most of them are based on the directly coherent pumping. Intuitively, dissipation is unfavorable for lasing. Here, we experimentally demonstrate a mechanism of generating phonon lasing from the dissipative coupling in a multimode optomechanical system. By precisely engineering the dissipations of two membranes and tuning the intensity modulation of the cavity light, the two-membrane-in-the-middle system exhibits non-Hermitian characteristics and the cavity-mediated interaction between two nanomechanical resonators becomes purely dissipative. The level attraction and damping repulsion are clearly exhibited as the signature of dissipative coupling. After the exceptional point, a non-Hermitian phase transition, where eigenvalues and the corresponding eigenmodes coalesce, two phonon modes are simultaneously excited into the self-sustained oscillation regime by increasing the interaction strength over a critical value (threshold). In distinct contrast to conventional phonon lasers, the measurement of the second-order phonon correlation reveals the oscillatory and biexponential phases in the nonlasing regime as well as the coherence phase in the lasing regime. Our study provides a method to study phonon lasers in a non-Hermitian open system and could be applied to a wide range of disciplines, including optics, acoustics, and quantum many-body physics.

Ultra-short bilayer graphene optical fiber intensity modulator based on silver-semicircular hybrid plasmonic waveguide

The intensity modulator is a key component in optical fiber communication. In this paper, an ultra-short graphene light intensity modulator based on hybrid plasmonic waveguide (HPW) array is proposed. Al2O3 embedded with double-layer graphene at a certain interval is placed on the side polishing surface of the microfiber Mach–Zehnder modulator (MZM), and the silver-semicircular array is placed on the surface of the transition material as hybrid plasmonic waveguide for the first time in all-fiber modulator. Analyzing by building a 3D model in finite difference time domain software, the hybrid surface plasmon polariton (HSPP) between silver-semicircles significantly enhances the subwavelength confinement and the light–graphene interaction. The modulation range of the real part of effective refractive index (Neff) can reach to 0.01984 by adjusting the Fermi level of graphene. Therefore, π phase change can be achieved only in a modulation length of 45 μm, and the insert loss can be controlled below 0.0159 dB/μm through the analysis of the imaginary part of the Neff, which also leads to a low total loss of 0.7155 dB. Owing to the excellent phase modulation efficiency, high extinction ratios of 39.39 dB and 47.77 dB can be reached for port 1 and port 2, respectively. Double-layer graphene forms the flat capacitor, which brings high modulation efficiency while achieving a high modulation bandwidth of 59.945 GHz. The application of HPW in graphene optical fiber modulator greatly improves the working efficiency, reduces the difficulty of integration, overcomes high insert loss, improves the extinction ratio, this modulator can be widely used in the future optical fiber communication system.

Actively manipulating the photonic spin Hall effect by bias-assisted light-induced carrier injection.

In this work, we present a simple and active mechanism for manipulating the photonic spin Hall effect (SHE) of an InP-based layered structure by taking advantage of the alterable refractive index of InP via bias-assisted carrier injection. The photonic SHE of transmitted light for both H- and V-polarized beams is quite sensitive to the intensity of the bias-assisted light. The spin shift can reach its giant value under the optimal intensity of bias light, which corresponds to the proper refractive index of InP induced by the photon-induced carrier injection. Except for the modulation of the bias light intensity, there is another method to manipulate the photonic SHE by adjusting the wavelength of bias light. We found that this method of tuning the bias light wavelength is more effective for H-polarized light than for the V-polarized light.

Effects of postpolymerization conditions on the physical properties, cytotoxicity, and dimensional accuracy of a 3D printed dental restorative material

Statement of problemAlthough the introduction of high-speed 3-dimensional (3D) printing technology has significantly reduced printing time, the time required for postpolymerization is a speed-determining step because of the long wait time. How postpolymerization conditions affect material properties is unclear. PurposeThe purpose of this in vitro study was to assess the physical properties, accuracy, and biosafety of a 3D printed dental restorative material according to postpolymerization conditions. Material and methodsSpecimens were prepared by 3D printing with a digital light processing 3D printer with 1 interim dental material (C&B MFH). All printed specimens underwent a postpolymerization process with 5 different postpolymerization devices and were designated as groups D1 (D102H), FO (Form Cure), LC (LC-3DPrintBox), ME (Medusa), and MP (MP100). The light intensity and temperature of each device were measured, and the Vickers hardness, flexural strength and modulus, degree of conversion (DC), cytotoxicity, and polymerization shrinkage were analyzed. Statistical analyses were conducted with 1-way analysis of variance, the Tukey post hoc test, and regression testing (α=.05). Scanning electron microscopy was used to assess the fracture surface characteristics of the specimens. ResultsLight intensity was strongest with the ME device, and the temperature inside the device during postpolymerization showed the highest increase with the LC device and the lowest increase with the D1 device. The LC group specimens showed the highest mean Vickers hardness, and the MP group showed the lowest. The flexural strength was ≥100 MPa in all groups, with a flexural modulus ranging from 1.17 to 1.5 GPa. The DC results were similar to the physical properties test results. The D1, FO, LC, and ME groups all showed ≥70% cell viability, indicating no toxicity. The FO group showed the highest shrinkage rate of 0.52%. ConclusionsWhen the light intensity was strong, the surface was sufficiently hard, and toxic substances were not eluted even after a short postpolymerization time, suggesting that light intensity modulation and time management can be used to improve the postpolymerization process.

Improved PGC demodulation algorithm to eliminate modulation depth and intensity disturbance.

In this paper, an improved phase generated carrier (PGC) demodulation algorithm based on frequency mixing and division difference is proposed. The effects of phase modulation depth variation and light intensity disturbance of the light source on the demodulated phase signal are investigated theoretically and experimentally. Compared to the traditional PGC differential-cross-multiplying (PGC-DCM) and PGC arctangent (PGC-Arctan) demodulation algorithms, the ameliorated demodulation algorithm eliminates the harmonic distortion of the demodulated signal by extracting the carrier modulation depth through frequency mixing. The demodulation error caused by the light intensity disturbance of the light source is suppressed by division difference. The stability of the demodulation system is improved. To verify the algorithm, a PGC demodulation system is built based on a Michelson interferometer. The experimental results show that when the frequency and amplitude of the sensed signal are set to 1 kHz and 0.4 rad, respectively, the signal-to-noise ratio with the proposed algorithm achieves a gain of 35.66 dB over the PGC-Arctan algorithm and 26.26 dB over the PGC-DCM algorithm.

Optical-intensity modulators with PbTe thermoelectric nanopowders for ultrafast photonics

As a new optical material with huge potential application, nanomaterials have attracted much attention in the field of ultrafast photonics due to their proper band gap, multiple structure and stable chemical property. Although there have been many reports on light intensity modulators in ultrafast photonics fabricated by nanomaterials in recent years, few work has been done to analyze the role of nanomaterials at different scales with light-matter interaction. It is found that bonding of different scales of PbTe to the tapered fiber surface by a controlled variable method confirms that nanopowder PbTe has better light intensity modulation capability compared to bulk PbTe. At last, an optical-intensity modulator based on nano PbTe was utilized to achieve 830 fs laser pulse in fiber ring laser. These studies indicate that PbTe shows great promise for ultrafast photonic applications, and effectively promoting the development of semiconductor crystal-based optical devices.

Design and fabrication of a micro-opto-mechanical-systems accelerometer based on intensity modulation of light fabricated by a modified deep-reactive-ion-etching process using silicon-on-insulator wafer

Accelerometers that work based on intensity modulation of light are more sensitive, economically feasible, and have a simpler fabrication process compared to wavelength modulation. A micro-opto-electro-mechanical-system accelerometer based on intensity modulation of light is designed and fabricated. A movable shutter that is attached to the proof mass is designed to change the intensity of light. Moreover, the mechanical part is designed to improve the overall sensitivity and linear behavior in the measurement range. The designed accelerometer is fabricated by a deep-reactive-ion-etching (DRIE) process. The DRIE process used in this report is based on a Bosch-like process, which uses SF6 and a mixture of H2, O2, and SF6 gases in etching and passivation subsequences, respectively. This method has a lower plasma density and a higher base pressure and causes higher verticality, which results in lower optical efficiency loss in comparison with the Bosch process. Furthermore, the functional characteristics of the accelerometer are derived with analytical and numerical methods, and the results are compared. The functional characteristics of the accelerometer are as follows: a resonant frequency of 0.56 kHz, a mechanical sensitivity of 0.6μm/g, an optical sensitivity of 16%/nm, an overall sensitivity of 9.6%/g, a footprint of 2000×2000μm2, a measurement range of 3g, a mechanical cross axis sensitivity of 0.058μm/g, and an overall cross axis sensitivity of 0.00029%/g. These functional characteristics make the design appropriate for a large range of applications.

Circular Displacement Current Induced Anomalous Magneto‐Optical Effects in High Index Mie Resonators

AbstractDielectric Mie nanoresonators showing strong light–matter interaction at the nanoscale may enable new functionality in photonic devices, such as strong magneto‐optical effects. However, most reports so far have been focused on the enhancement of conventional magneto‐optical effects. Here, anomalous magneto‐optical effects are observed in high‐index‐contrast Si/Ce:YIG/YIG/SiO2 Mie resonators. In particular, giant modulation of light intensity in transverse magnetic configuration up to 6.4% under s‐polarized incidence appears, which is non‐existent in planar magneto‐optical thin films. A large rotation of transmitted light polarization in longitudinal magnetic configuration is also observed, which is two orders of magnitude higher than for planar magneto‐optical thin films. These phenomena are originated from the unique circular displacement current when exciting magnetic resonances in the Mie resonators, which change the electric field direction locally. This work indicates an uncharted territory of light polarization control based on complex modal profiles in all‐dielectric magneto‐optical Mie resonators and metasurfaces.

Calibration method of ultra-low emission particulate concentration measurement by light scattering method

Abstract To reduce the error caused by optical device pollution and background value drift in the measurement process of ultra-low emission particulate concentration by light scattering method, an on-line calibration method which can realize self-check and full-range calibration was put forward. The single light source spectral method was used to set up calibration light path, through a strong emphasis on technology achieving light signal extraction. The calibration effect was evaluated based on the dust tunnel system. The results show that the light intensity-modulated technique can significantly improve the measurement accuracy of low concentration particles compared with the constant light intensity technology. When the concentration of particles to be measured is higher than 500 μg/m³, the relative error between the measurement results of the experimental prototype and those of the filter membrane weighing method is less than 10 %. The optimal calibration period of the measuring instrument is 3 hours. When the variation deviation from the calibration light intensity of light intensity modulation is less than 2 %, the relative error between the particle concentration measurement result and the filter membrane weighing method is less than 10 %.

Cone-Driven Retinal Responses Are Shaped by Rod But Not Cone HCN1.

Signal integration of converging neural circuits is poorly understood. One example is in the retina where the integration of rod and cone signaling is responsible for the large dynamic range of vision. The relative contribution of rods versus cones is dictated by a complex function involving background light intensity and stimulus temporal frequency. One understudied mechanism involved in coordinating rod and cone signaling onto the shared retinal circuit is the hyperpolarization activated current (Ih) mediated by hyperpolarization-activated cyclic nucleotide-gated 1 (HCN1) channels expressed in rods and cones. Ih opposes membrane hyperpolarization driven by activation of the phototransduction cascade and modulates the strength and kinetics of the photoreceptor voltage response. We examined conditional knock-out (KO) of HCN1 from mouse rods using electroretinography (ERG). In the absence of HCN1, rod responses are prolonged in dim light which altered the response to slow modulation of light intensity both at the level of retinal signaling and behavior. Under brighter intensities, cone-driven signaling was suppressed. To our surprise, conditional KO of HCN1 from mouse cones had no effect on cone-mediated signaling. We propose that Ih is dispensable in cones because of the high level of temporal control of cone phototransduction. Thus, HCN1 is required for cone-driven retinal signaling only indirectly by modulating the voltage response of rods to limit their output.SIGNIFICANCE STATEMENT Hyperpolarization gated hyperpolarization-activated cyclic nucleotide-gated 1 (HCN1) channels carry a feedback current that helps to reset light-activated photoreceptors. Using conditional HCN1 knock-out (KO) mice we show that ablating HCN1 from rods allows rods to signal in bright light when they are normally shut down. Instead of enhancing vision this results in suppressing cone signaling. Conversely, ablating HCN1 from cones was of no consequence. This work provides novel insights into the integration of rod and cone signaling in the retina and challenges our assumptions about the role of HCN1 in cones.

Low insert loss bilayer graphene compact twin-core optical fiber intensity modulator

A compact modulator with high bandwidth and extinction ratio is proposed to achieve light intensity modulation by adjusting the phase of the light transmitted in the fiber. The better modulation effect is achieved by placing two-lamellae of graphene embedded in Al2O3and PVB on a side-polished microfiber of MZM. Finite element software is used to analyze the modulation effect, the function of the chemical potential of graphene and the effective refractive of modulator is established. Extinction ratios of port 1 and port 2 can reach 11.54 dB and 11.88 dB in 92 μm by substituting the function into simulation. While achieving a more compact modulation structure, the insert loss is also controlled below 0.0193 dB/μm. For the first time, the contact width between bilayer graphene and the electrode is increased by placing the electrode at the head and end of the modulator, which leads to 132.427 GHz modulation bandwidth. And the modulator does not require the excess support structure necessarily benefit from the placement of the electrode. The proposed phase-shift light intensity modulator has high extinction ratio and large bandwidth, which leads to great transmission capacity and modulate speed.

Physiological and biochemical responses of Chinese cabbage (Brassica rapa var. chinensis) to different light treatments

BackgroundArtificial agriculture is promoted as an economically viable technology for developing plants under controlled conditions whereby light, water, and fertilizer intake are regulated in a controlled manner to produce maximum productivity with minimal resources. Artificial light has been used to produce high-quality vegetables because it can regulate plant growth and phytochemical production through light intensity, photoperiod, and spectrum modulation. This study aimed to compare the physiological and biochemical responses of Chinese cabbage (Brassica rapa var. chinensis) grown under artificial light with varying light intensities (75 and 150 µmol m−2 s−1), photoperiods (12:12 and 6:6:6:6 h), and wavelengths (blue, red, and magenta) to plants grown in a glasshouse under natural light. The novelty of this study lies in the manipulation of artificial LED lighting to achieve high-quality plant growth and phytochemical composition in B. rapa model vegetables for potential optimal productivity.ResultsThe analysis revealed that B. rapa grown under artificial lights produced more consistent biomass yield and had a higher chlorophyll content than B. rapa grown under natural light (control). Plants grown under artificial lights have also been shown to produce biochemical compositions derived primarily from fatty acids, whereas plants grown under natural light have a biochemical composition derived primarily from alkanes. Twenty compounds were found to be statistically different between light treatments out of a total of 31 compounds detected, indicating that they were synthesized in response to specific light conditions. Exposure to the full artificial light spectrum (white) resulted in the absence of compounds such as dodecane and 2,6,10-trimethyltridecane, which were present in B. rapa grown in natural light, whereas exposure to the blue spectrum specifically induced the production of tetracosane. Eicosane, neophytadiene, l-(+)-ascorbic acid 2,6-dihexadecanoate, and (Z,Z,Z)-9,12,15-octadecatrienoic acid were all prevalent compounds produced in B. rapa regardless of light conditions, and their absence may thus affect plant development and survival.ConclusionsThe results show that cultivation under artificial light produced consistent biomass, high chlorophyll content, and phytochemical content comparable to natural light conditions (control). These findings shed light on how artificial light could improve the production efficiency and organoleptic qualities of Chinese cabbage.Graphical

Photosensitive Alignment: Advanced Electronic Paper-Based Devices

In this review we describe the reversible photoalignment effect imposed on the director in nematic liquid crystals that provides an approach for fabrication of advanced optically addressed devices. Several new concepts have been developed to render photosensitive materials during the past decade. Functional soft azo dye compounds exhibiting distinct functionalities in response to polarized light are highly desirable for fabrication of optically rewritable electronic paper. An optically rewritable element base using simple and inexpensive materials can potentially enable the development of novel environmentally friendly, paper-like gadgets with improved functionality over regular electronic paper. We argue that an optically rewritable technique is relevant for some applications, where conventional paper might be irrelevant. In particular, we have tested and discussed several techniques of color and 3D image formation. This strategy for fabrication of novel devices offers versatile methods for visualization. We also show that the intensity modulation of the irradiation light has a potential to generate improved grayscale visualization. This principle is based on the statistical distribution control of photosensitive azo dye molecules, driven by the incident polarized light. Additionally, we discuss the functional characteristics of the developed prototypes.

Polymer Stabilization of Uniform Lying Helix Texture in a Bimesogen-Doped Cholesteric Liquid Crystal for Frequency-Modulated Electro-Optic Responses.

A polymer network (PN) can sustain the uniform lying helix (ULH) texture in a binary cholesteric liquid crystal (LC) comprising a calamitic LC and a bimesogenic LC dimer. Upon copolymerization of a bifunctional monomer with a trifunctional monomer at a concentration of 5 wt% to create the desired polymer network structure, the PN-ULH was obtained with high stability and recoverability even when cycles of helical unwinding-to-rewinding processes were induced after the electrical or thermal treatment. Utilizing dielectric spectroscopy, the flexoelectric-polarization-dominated dielectric relaxation in the PN-ULH state was characterized to determine two frequency regions, f < fflexo and f > fdi, with pronounced and suppressed flexoelectric effect, respectively. It is demonstrated that the cell in the PN-ULH state can operate in the light-intensity modulation mode by the flexoelectric and dielectric effects at f < fflexo and phase-shift mode by the dielectric effect at f > fdi. Moreover, varying the voltage frequency from f < fflexo to f > fdi results in a frequency dispersion of transmittance analogous to that of flexoelectric-polarization-dominated dielectric relaxation. The unique combination of the bimesogen-doped cholesteric LC with a stable and recoverable PN-ULH texture is thus promising for developing a frequency-modulated electro-optic device.

FPGA-Based High-Speed Optical Fiber Sensor Based on Multitone-Mixing Interferometry

We report a real-time high-speed fiber Bragg grating (FBG) interrogator based on a fiber-optic interferometer. The signal processing is performed by using a low-cost field-programmable gate array (FPGA) system, which is programed to implement a phase-generated carrier (PGC) demodulation algorithm with multitone mixing (MTM) to provide distortion-free signals with high tolerance to modulation depth variations and light intensity fluctuations. The system can stream data at rates up to 1 MS/s and allows multiplexed processing up to two channels. Experimental results show simultaneous measurements of two FBGs, one of which was actuated at frequencies up to 100 kHz. The system features a 3-dB bandwidth of 280 kHz, and a dynamic wavelength resolution of 4.7 fm/Hz <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$^{\mathrm {1/2}}$ </tex-math></inline-formula> . We also demonstrate a strong reduction of distortion using the MTM approach with respect to the standard technique. Finally, we study the origin of the noise, demonstrating a reduction in common noise sources by using one of the FBGs as a reference. The system can measure FBGs centered at any position within the spectral band of the source, is polarization-independent, and is easily scalable to more than two measurement channels from the same interferometer.

Process Intensification in Photocatalytic Decomposition of Formic Acid over a TiO2 Catalyst by Forced Periodic Modulation of Concentration, Temperature, Flowrate and Light Intensity

The effect of forced periodic modulation of several input parameters on the rate of photocatalytic decomposition of formic acid over a TiO2 thin film catalyst has been investigated in a continuously stirred tank reactor. The kinetic model was adopted based on the literature and it includes acid adsorption, desorption steps, the formation of photocatalytic active sites and decomposition of the adsorbed species over the active titania sites. A reactor model was developed that describes mass balances of reactive species. The analysis of the reactor was performed with a computer-aided nonlinear frequency response method. Initially, the effect of amplitude and frequency of four input parameters (flowrate, acid concentration, temperature and light intensity) were studied. All single inputs provided only a minor improvement, which did not exceed 4%. However, a modulation of two input parameters, inlet flowrate and the acid molar fraction, considerably improved the acid conversion from 80 to 96%. This is equivalent to a factor of two increase in residence time at steady-state operation at the same temperature and acid concentration.

Short-wavelength infrared (SWIR) photodetector based on multi-layer 2D GaGeTe.

Recent theoretical studies proposed that two-dimensional (2D) GaGeTe crystals have promising high detection sensitivity at infrared wavelengths and can offer ultra-fast operation. This can be attributed to their small optical bandgap and high carrier mobility. However, experimental studies on GaGeTe in the infrared region are lacking and this exciting property has not been explored yet. In this work, we demonstrate a short-wavelength infrared (SWIR) photodetector based on a multilayer (ML) GaGeTe field-effect transistor (FET). Fabricated devices show a p-type behavior at room temperature with a hole field-effect mobility of 8.6 - 20 cm2 V-1s-1. Notably, under 1310 nm illumination, the photo responsivities and noise equivalent power of the detectors with 65 nm flake thickness can reach up to 57 A/W and 0.1 nW/Hz1/2, respectively, at a drain-source bias (Vds) = 2 V. The frequency responses of the photodetectors were also measured with a 1310 nm intensity-modulated light. Devices exhibit a response up to 100 MHz with a 3dB cut-off frequency of 0.9 MHz. Furthermore, we also tested the dependence of the device frequency response on the applied bias and gate voltages. These early experimental findings stimulate the potential use of multilayer GaGeTe for highly sensitive and ultrafast photodetection applications.

Silicon-Based All-Dielectric Metasurface on an Iron Garnet Film for Efficient Magneto-Optical Light Modulation in Near IR Range.

All-dielectric nanostructures provide a unique low-loss platform for efficiently increasing light-matter interaction via excitation of the localized or propagating optical modes. Here, we report on the transverse magneto-optical Kerr effect enhancement in an all-dielectric metasurface based on a two-dimensional array of Si nanodisks on a cerium substituted dysprosium iron garnet thin film. We observed up to 15% light intensity modulation under TM modes excitation. The observed magneto-optical effect is nearly independent of the rotation of the light incidence plane with respect to the metasurface. Being compatible with conventional semiconductor technology, our structure holds promise for device applications, such as light modulators, magnetic and chemical sensors.