Layer-structured Materials Research Articles

Effect of High Heat Flux of Helium and Hydrogen Plasma Jet on the Material Properties of Piezoelectric PZT-Ceramics

A set of experimental and measurement techniques to study the influence of a plasma jet on the main material parameters of piezoelectric ceramics has been presented. A series of plasma experiments has been carried out using a pulsed plasma jet system. It allows of a metered-dose exposure to plasma of different composition and fluence with a constant particle flux density of 1021/m2, energy flux density of 0.1 MJ/m2 and average particle energy of 100–200 eV in a pulse duration of 15 μs. The study of the effects that a repeated exposure to an extreme heat flux of helium and hydrogen plasmas has on the near-surface layer structure and basic material parameters of mass-produced piezoelectric ceramic samples has been presented. The main result of the research is an experimental confirmation of the surface micro-structuring starting after just a few cycles of plasma exposure while only a slight decrease of the main material parameters as well as the preservation of polarization has been observed for two types of different compositions of PZT-ceramics. A further increase in the number of exposure pulses leads to practically no change of main material parameters of both ceramics, even showing a tendency for recovery instead.

Enhancing the potassium-ion storage performance of potassium manganese oxide cathode by single-element doping strategies

Layered manganese-based oxides are considered as ideal cathode materials for potassium-ion batteries (PIBs) due to their ease of synthesis and relatively large interlayer spacing. Nevertheless, the Jahn-Teller effect of Mn3+ and the irreversible phase transitions in high-voltage regions of layered manganese-based oxide leads to slow diffusion kinetics of potassium ions and severe capacity fading. Herein, a series of single-element doped manganese-based oxide cathodes K0.5Mn0.98X0.02O2 (X = Fe, Mg, Cu, Ti and Zn) are designed and investigated. The results demonstrate that trace doping with these elements stabilizes the layered structure of KMnO2 cathode materials, improves the diffusion coefficient of K+, and effectively suppresses the P3-O3-P3 phase transition in high-voltage regions. Among the doping-samples, the K0.5Mn0.98Fe0.02O2 exhibits outstanding reversible specific capacity of 127 mAh g−1 at a current density of 20 mA g−1. Meanwhile, K0.5Mn0.98Ti0.02O2 demonstrates exceptional cycling stability and rate capability, retaining 83.8 % of its initial capacity after 300 cycles at 200 mA g−1, and maintaining a high specific capacity close to 40 mAh g−1 even at 1000 mA g−1. This study validates the feasibility of trace element doping in enhancing the electrochemical performance of layered Mn-based cathode materials for PIBs.

Misfit Layered Compounds: Insights into Chemical, Kinetic, and Thermodynamic Stability of Nanophases.

ConspectusCompounds with layered structures (2D-materials), like transition metal-dichalcogenides (e.g., MoS2), attracted a great deal of interest in the scientific community in recent years. This interest can be attributed to their unique lamellar structure, which induces large anisotropy in their physicochemical properties. Furthermore, owing to the weak van der Waals interaction between the layers, they can be cleaved along the a-b plane, which allows fabricating single layers with physical properties entirely different from the bulk material. Moreover, stacking layers of different 2D-materials on top of each other has led to a wealth of new observations, for instance, by twisting two layers with respect to each other and producing Moiré lattice. Another outstanding property of inorganic layer compounds is their tendency to form nanotubes, reported first (for WS2) many years ago and subsequently from many other layered compounds.Among the 2D-materials, misfit layer compounds make a special class with an incommensurate and nonstoichiometric lattice made of an alternating layer with rocksalt structure, like LaS (O) and a layer with hexagonal structure, like TaS2 (T). The lack of lattice commensuration between the two slabs leads to a built-in strain, which can be relaxed via bending. Consequently, nanotubes have been produced from numerous MLC compounds over the past decade and their structure was elucidated.Owing to their large surface area, nanostructures are generally metastable and tend to recrystallize into microscopic crystallites via different mechanisms, like Ostwald ripening, or chemically decompose and then recrystallize. The stability of nanostructures at elevated temperatures has been investigated quite scarcely so far. In this perspective, electron microscopy as well as synchrotron-based X-ray absorption and reflection techniques were used to elucidate the chemical selectivity and decomposition routes of rare-earth based MLC nanotubes prepared at elevated temperatures (800-1200 °C).As for the chemical selectivity, entropic effects are expected to dictate the random distribution of the chalcogen atoms on the anion sites of the MLC nanotubes at elevated temperatures. Nonetheless, the sulfur atoms were found to bind exclusively to the rare-earth atom (Ln = La, Sm) of the rocksalt slab and the selenium to the tantalum of the hexagonal TX2 slab. This uncommon selectivity was not found in other kinds of nanotubes like WSe2xS2(1-x). In other series of experiments, the lack of utter symmetry in the multiwall nanotubes leads to exclusions of certain X-ray (0kl) reflections, which was used to distinguish them from the bulk crystallites. The transformation of Ln-based MLC nanotubes into microscopic flakes was followed as a function of the synthesis temperature (800-1200 °C) and the synthesis time (1-96 h). Furthermore, sequential high-temperature transformations of the (O-T) lattice into (O-T-T) and finally (O-T-T-T) phases via deintercalation of the LnS slab was observed. This autocatalytic process is reminiscent of the deintercalation of alkali atoms from different layered structure materials. Annealing at higher temperatures and for longer periods of time eventually leads to the decomposition of the ternary MLC into binary metal-sulfide phases, as well as partial oxidation of the product. This study sheds light on the complex mechanism of high-temperature chemical stability of the nanostructures.

Extremely Fast Wicking Self‐Layered Interpenetrating Network Hydrogel for Rapid All Day Collection of Atmospheric Water

AbstractHygroscopic salt hydrogel photothermal composites and related technology are a promising pathway for water harvesting. However, due to the overly cumbersome preparation process, the distribution of the surface photothermal layer is difficult to control and the photothermal efficiency is low. In this paper, a method is proposed to greatly simplify the preparation process of photothermal layer hydrogels and improve their atmospheric water harvesting performance by constructing temperature‐sensitive interpenetrating networks. Due to the decomposition of some reversible hydrated structures in the network during heating and warming, carbon nanotubes move autonomously to form a layered structure with a photothermal effect on the upper surface, which can return to its original state after cooling and remain stable at room temperature or under solar illumination. Compared with hydrogels with general layered structure or overall distribution of photothermal materials, agar/GG/PAM/CNT hydrogel has faster moisture adsorption efficiency and higher desorption efficiency, and during the 24 h continuous sorption–desorption cycle is capable of achieving high water yield of 2.57 Lwater kgsorbents−1 day−1, superior to most recent hydrogel adsorbents. Simplifying the preparation process while maintaining high efficiency, while greatly improving photothermal performance, paves the way for cost‐effective mass production applications for a wide range of hygroscopic salt‐hydrogel photothermal composites.

Electronic structure investigation and anisotropic phonon anharmonicity in ternary ZrGeTe4 single crystals

Ternary two-dimensional (2D) transition metal chalcogenides have gained immense attention because of their ability to overcome the intrinsic limitations of their binary counterparts. Layered 2D materials are important for future electronic and photonic devices owing to their low structural symmetry and in-plane anisotropy with tunable bandgap. Herein, the electronic structure and detailed vibrational properties of bulk ZrGeTe4 layered single crystals were investigated using angle-resolved photoemission spectroscopy (ARPES) and Raman scattering (RS). The ARPES results revealed an anisotropic Fermi surface of different momentum along kx and ky from the zone center and an anisotropic band structure with varying band curvatures along the high-symmetry directions. Furthermore, the RS of ZrGeTe4 was investigated under different polarizations and varying temperatures. The polarized RS exhibited twofold and fourfold symmetry orientations in different configurations, revealing the anisotropic phonon dispersions for bulk ZrGeTe4. The observed softening of Raman modes was corroborated with the anharmonic phonon dispersion, which was further supported by our third-order force constant calculations of thermal transport using density functional theory. Low lattice thermal conductivity with increasing temperature is linked with enhanced phonon–phonon scattering, which is evident from the decreased phonon lifetime and peak linewidth. In addition to these fundamental aspects, the anisotropic nature and unique layered structure of such materials reveal their bright future for next-generation nanoelectronic applications.

Improving the Performance of LiNi0.925Co0.065Mn0.01O2 via Ti4+& Nb5+ Co-Modifications.

Ni-rich layer-structured materials are some of the most promising cathodes owing to their attractive reversible capacity and cost-effectiveness. When the Ni content is increased to 90% and higher, mechanical deterioration becomes serious and leads to accelerated cyclic degradation, since removable Li+ is ∼0.85, accompanied by large lattice variation during operation. Here, we investigate the influences of Ti4+ bulky substitution, Nb5+ surface treatment, and their coutilization on the behavior of LiNi0.925Co0.065Mn0.01O2 (NCM92). In contrast to the limited positive effects of monousage, the coutilization of Ti4+ and Nb5+ obviously suppresses particles' pulverization, relying on their synergistic effects of the shape of lattice variation and the protection of a tough shell layer. As a result, Ti & Nb-LiNi0.925Co0.065Mn0.01O2 (TiNb-NCM92) presents the best capacity retention, as high as 90.2% after 300 cycles, much higher than NCM92 (49.0%), Ti-NCM92 (76.3%), and Nb-NCM92 (72.4%). Our approaches demonstrate that the serious mechanical challenges of ultrahigh nickel cathodes could be alleviated by various remedies coutilized together.

Recent Progress and Applications of NanoIR‐AFM in Morphological Characterization of Organic Solar Cells

AbstractOrganic solar cells (OSCs) are gaining attention in building‐integrated and agricultural photovoltaics due to their light weight, mechanical flexibility, and low‐cost solution processability. To achieve commercial viability, understanding the relationships between active layer material structure, film morphology, and photovoltaic performance is crucial. Nanoscale infrared spectroscopy coupled with atomic force microscopy (nanoIR‐AFM) offers an advanced characterization of active layer morphology at high resolution to help understand OSC performance. This review outlines recent developments and applications of nanoIR‐AFM in OSC research, detailing its principles, instruments, and functions. Strategies to enhance OSC performance and their morphological characterization by nanoIR‐AFM are discussed, offering insights into active layer evolution and device performance. The review highlights challenges faced by nanoIR‐AFM in OSC applications and highlights its potential role in advancing OSC technology. As nanoIR‐AFM continues to evolve, it will play a critical role in OSC development, providing essential technical means for further progress.

Effects of multi-element composition regulation on the structure and electrochemistry of P2-type layered cathode materials

P2-type Mn-based oxides are promising cathode materials for sodium-ion batteries due to their low cost and high capacity virtue. However, the irreversible phase transition and unstable anion redox at high operating voltages (∼4.2 V) will cause structural distortions, leading to slow sodium-ion diffusion kinetics and severe capacity degradation. Herein, a multi-elemental composition regulation strategy is proposed to enhance the structural stability of P2-type cathode by optimizing the structure and modulating the irreversible oxygen redox during high-voltage cycling. A series of multi-element cathodes Na0.67(Fe1/4Co1/4Ni1/4Ti1/4)1-xMnxO2 (x = 0.4,0.5,0.6,0.7,0.8,0.9) are designed and the effects of component modulation on their structure and electrochemical behavior are systematically investigated. Especially, the optimized Na0.67Fe0.05Co0.05Ni0.05Ti0.05Mn0.8O2 cathode maintains P2 phase during the initial charging/discharging between 1.5 V and 4.5 V, inhibits irreversible oxygen redox, and exhibits small lattice expansion. Impressively, the above optimized cathode exhibits superior cycling stability with capacity retention of nearly 90 % and reversible capacity of 130.1 mAhg−1 after 100 cycles at 1C rate. Furthermore, the optimized cathode also displays an excellent rate capability (capacity of 108.2 mAh g−1 at 5 C rate) due to the enhanced Na+ diffusion kinetics. This work provides new insight into developing high-stable Mn-based oxide cathodes operating at high voltage for sodium-ion batteries.

Multiphase riveting structure constructed by slight molybdenum for enhanced P3/O3 layer-structured oxide cathode material

Phase engineering has been efficiently employed to improve the performance of transition metal oxide cathode materials by alleviating the Jahn-Teller effects and optimizing the ions diffusion pathway. The second-order Jahn-Teller effects by slight molybdenum substitution was confirmed to activate a new phase formation and to construct a multiphase riveting structure. A P3/O3 riveting-structured NaNi0.3Mn0.52Mo0.03Cu0.1Ti0.05O2 cathode material was successfully synthesized for sodium ion batteries, which undergoes a reversible phase transition from P3/O3 → P3 → Hex.O3′ when charged to 4.25 V and most of the materials will transform into P3 phase after the first charge–discharge cycle. Due to the high reversibility and crystal structure stability, it indicates 155.0 mAh g−1 discharge capacity with a high up to 99.65 % initial Coulomb efficiency. This P3/O3 riveting structure can alleviate the rigid failure caused by phase transition. Meanwhile, O3/P3 phases provide the main storage sites for Na+ as skeletons and the existence of P3 phase provides a better diffusion pathway for ion transport.

Regulating Interfacial Compositions to Build a Stable Superlattice Structure of Layered Oxide Cathode Materials for Sodium-Ion Batteries

Regulating Interfacial Compositions to Build a Stable Superlattice Structure of Layered Oxide Cathode Materials for Sodium-Ion Batteries

High stability and selectivity of butterfly pea flower extract-NiAl LDH-based catalysts in the tetracycline degradation.

Layered double hydroxide (LDH) is an applicable material that can be modified in various ways. Modifications using natural extracts fulfill the principles of "green chemistry." The preparation of butterfly pea flower extract (BPE)-modified NiAl LDH was completed using the calcination and restacking method. The characteristics of the prepared composites were identified through analysis of functional groups, crystal phase, bandgap energy, surface area and surface morphology. Fourier transform-infrared (FT-IR) characterization revealed that the active group of the catalyst is -OH except for NiAl layered double oxide (LDO), which has the metal oxide-like functional groups. X-ray diffraction patterns expressed a typical layered material structure of NiAl LDH dan NiAl LDH-BPE, but not for NiAl LDO and NiAl LDO-BPE. Introducing BPE into NiAl LDH and NiAl LDO effectively decreased the bandgap energy and changed the surface morphology. The prepared catalysts were applied in a batch system with pH 5 to degrade tetracycline (TC). NiAl LDO demonstrated the highest activity as a catalyst in TC degradation, with a 93.61% degradation rate. In contrast, NiAl LDO-BPE demonstrated the highest structural stability in TC degradation and repeated use, with an initial degradation percentage of 82.58% and a fifth regeneration percentage of 71.4%.

Multilayer Optics for Synchrotron Applications

AbstractX‐ray multilayer optics play a vital role in synchrotron optics due to their ability to generate constructive interference. These devices typically consist of several tens to hundreds of periods of alternating layers coated on a substrate. In contrast to single‐layer mirrors that reflect X‐rays within a specific energy range, multilayer optics can be tailored to achieve a high reflection over a broad energy spectrum. This is a sought‐after property for many beamlines and has led to the development of numerous new X‐ray applications and capabilities. This review highlights advances in multilayer optics, including fabrication techniques, layer structure design, material choice, and strategies to enhance performance. This is placed in the context of recent applications of such multilayers as monochromator and gratings, focusing devices, and polarizers. Current challenges and the future outlook within this field are also proposed. This comprehensive summary of a rapidly advancing field highlights recent achievements and is intended to promote practical applications in terms of the use of multilayer synchrotron optics.

Enhancing performance and stability of LiNi0.8Co0.1Mn0.1O2 cathode via Na/Y dual doping for Lithium-Ion batteries

Nickel-rich layered oxide cathode materials face limitations in practical applications due to trade-offs between capacity and structural stability. As more Li+ is extracted during charging, the layered structure of nickel-rich materials becomes increasingly fragile. To address this, a double doping strategy with Na and Y is proposed in this study to enhance the strength of the layered structure. The research findings demonstrate that Na doping enlarges the spacing between Li layers in the crystal structure, while Y doping improves the reversibility of the H2-H3 phase transition but narrows the Li layer spacing in nickel-rich materials. Na and Y double doping, the advantages of Na in enlarging the Li layer, and Y in improving the H2-H3 phase transition can be harnessed simultaneously. This double doping strategy ensures that the laminar structure of the cathode material remains stable even when it is highly detached, effectively solving the trade-off between the capacity and structural stability of nickel-rich laminar cathode materials. The application in LiNi0.8Co0.1Mn0.1O2 shows that the capacity and cycle life of cathode materials can be significantly improved after Na/Y double doping. These findings open up opportunities for practical applications of nickel-rich cathode materials in lithium-ion batteries.

Trifunctional Rb+-Intercalation Enhancing the Electrochemical Cyclability of Ammonium Vanadate Cathode for Aqueous Zinc Ion Batteries.

Rechargeable aqueous zinc-ion batteries (AZIBs) have been highly desired due to their low cost, intrinsic safety, environmental friendliness, and great potential in large-scale power storage systems. However, their practical applications are impeded by unstable long-term electrochemical performances induced by microstructure degradation of the cathode material, hydrogen evolution reaction in the electrolyte, and dendritic growth on the zinc anode upon cycling. In this work, rubidium cations (Rb+) are introduced to synthesize an Rb+-preintercalated NH4V4O10 (NVO-Rb) composite. The contribution of Rb+ ions as pillars in V-O interlayers to facilitating Zn2+ storage is investigated first, and then the influences of partial Rb+ ions from the NVO-Rb cathode on the aqueous electrolyte and zinc anode are specially inspected from different viewpoints. Based on a series of characterization results, it is comprehensively elucidated that the partial Rb+ ions into the electrolyte suppress the generation of byproducts on the cathode and regulate the dendrite growth on the zinc anode, thus effectively promoting the long-term electrochemical performances of NVO-based AZIBs. The assembled Zn∥Zn(CF3SO3)2∥NVO-Rb cell can exhibit a high specific capacity and optimized Zn2+ diffusion kinetics, especially an improved electrochemical cyclability with a capacity retention of 87.6% at 5 A g-1 over 10000 cycles. This study enlightens the multiple roles of cation-preintercalation in the layered structure material and provides a feasible strategy for the development of high-performance aqueous batteries.

A theoretical study of all-inorganic perovskite solar cells: Computational modeling of the CsPbI[formula omitted]/RbGeI[formula omitted] bilayer absorber structure

All-inorganic perovskite solar cells (AI-PSCs) have garnered significant attention in the perovskite community due to their stability and efficient photogeneration and absorption capabilities. Despite the toxicity associated with all-inorganic CsPbI3 perovskites containing lead (Pb), its presence remains crucial for achieving excellent photovoltaic properties. However, the imperative shift towards AI-PSCs using less toxic materials with suitable photovoltaic properties is imperative. The incorporation of a double perovskite absorber layer allows for broadening the absorption spectrum of PSCs and enhancing cell stability. In this study, we propose a novel AI-PSC structure with CsPbI3 as the top absorber with a wide bandgap of 1.69 eV and a lead-free RbGeI3 perovskite as the bottom absorber layer with a low bandgap of 1.31 eV. Utilizing numerical simulations with the SCAPS-1D simulator, we analyze the photovoltaic parameters of AI-PSCs with single and double absorber layers. Our investigations reveal that a double absorber layer structure, comprising CsPbI3 and RbGeI3 materials, outperforms a single-junction PSC based on CsPbI3. By optimizing critical device parameters, we achieved an impressive efficiency of 31.91% in an AI-PSC device with a CsPbI3(0.6 μm)/RbGeI3(2 μm) bilayer configuration. This study positions lead-free RbGeI3 perovskite as a promising partner for CsPbI3, offering a potential pathway for the development of highly efficient AI-PSCs.

Modification Strategies and Challenges of High‐Performance Lithium‐Rich Manganese‐Based Cathode Materials

Lithium‐rich manganese‐based (LRM) cathode materials have recently gained increasing attention for their remarkable reversible capacity of up to 378 mAh g−1. However, the development of these materials is hindered by several challenges, including oxygen deficiency, migration of transition metal ions, and structural changes from lamellar to spinel phases. As a result, these limitations result in a low initial Coulomb efficiency, capacity/voltage decay, and inadequate cycle life. To address these issues, the modification of layered lithium‐rich materials proves to be an effective approach. In this review, the structure and electrochemical properties of layered LRM materials are introduced and various systematic modification strategies are discussed. Herein, the current state and future prospects of several strategies such as doping, surface coating, and structure control are delved into. Furthermore, development ideas for achieving high‐capacity and long‐cycle‐layered LRM cathode materials are presented.

Correlation between regulated structure of Li-rich layered oxide and low-potential TM redox

The anionic (oxygen) redox is known responsible for the high specific capacity and the transition metal (TM) migration of the Li- and Mn-rich (LMR) layer-structured oxide cathode materials. The reversibility of the TM redox was taken for granted; less attention has been paid to the relationship between structural degradation (TM migration and oxygen loss) and the redox behavior of the TM ions at low potentials. In combination of the crystalline and electronic structural characterizations and the electrochemical evaluation, we revealed in this article that the TM migration (Li-TM mixing) and the intensive anionic oxidation at high potentials suppress the Co2+/3+ redox and trigger the Mn3+/4+ redox at low potentials. The Mn3+/4+ redox accelerates the structural distortion and reduces the average discharge potential though both the Co2+/3+ and Mn3+/4+ redox contribute to charge compensation and the total capacity. Slightly decreasing the initial delithiation (charge cut-off potential decreases to 4.6 V vs. Li+/Li) mitigates the TM migration in Li1.2Ni0.13Co0.13Mn0.54O2 and significantly improves its structural stability and cycling performance after the charge cut-off potential recovers to the “normal” value (4.8 V) in the subsequent cycling. The dependence of the electronic structure of the Co3d and Mn3d orbitals on structural degradation is clarified with the density functional theory (DFT) calculations. It was shown that the TM migration in LMR results in the decrease of the unoccupied states of the Co3d orbitals and the shifting of the unoccupied states of the Mn3d orbital towards the Fermi energy level. These findings reveal the correlation between the structural degradation and the behavior of the low-potential TM redox, and will inspire ways to excavate a higher capacity in LMRs by activating more TM redox couples.

A 3D modeling method of layered acoustic material structures with finite dimensions

Modeling of layered acoustic structures to predict the sound absorption characteristics of complex materials is a widely used method in room acoustic practice. Commonly used modeling techniques-such as the transfer matrix method-typically assume locally reacting surfaces of infinite lateral dimensions and provide one-dimensional calculations only, offering limited accuracy, especially for resonant absorbers with finite dimensions. We present the direct, analytical modeling of sound propagation in extendedly reacting layered materials of finite dimensions allowing the estimation of the surface impedance or admittance distribution of layered structures, from which sound absorption properties can be calculated. The theoretical results are validated by measurements, performed on a small-sized resonant panel absorber. We present the implementation of the method in the soundy.ai application.

Layer-Structured Multitransition-Metal Oxide Cathode Materials for Potassium-Ion Batteries with Long Cycling Lifespan and Superior Rate Capability.

Manganese (Mn)-based layer-structured transition metal oxides are considered as excellent cathode materials for potassium ion batteries (KIBs) owing to their low theoretical cost and high voltage plateau. The energy density and cycling lifetime, however, cannot simultaneously satisfy the basic requirements of the market for energy storage systems. One of the primary causes results from the complex structural transformation and transition metal migration during the ion intercalation and deintercalation process. The orbital and electronic structure of the octahedral center metal element plays an important role for maintaining the octahedral structural integrity and improving the K+ diffusivity by the introduced heterogeneous [Me-O] chemical bonding. A multitransition metal oxide, P3-type K0.5Mn0.85Co0.05Fe0.05Al0.05O2 (KMCFAO), was synthesized and employed as a cathode material for KIBs. Beneficial from the larger layer spacing for K+ to better accommodate and effectively preventing the irreversible structural transformation in the insertion/extraction process, it can reach a superior capacity retention up to 96.8% after 300 cycles at a current density of 500 mA g-1. The full cell of KMCFAO//hard carbon exhibits an encouraging promising energy density of 113.8 W h kg-1 at 100 mA g-1 and a capacity retention of 72.6% for 500 cycles.

Computational Fluid Dynamics Modeling of the Filtration of 2D Materials Using Hollow Fiber Membranes

The current study presents a computational fluid dynamics (CFDs) model designed to simulate the microfiltration of 2D materials using hollow fiber membranes from their dispersion. Microfiltration has recently been proposed as a cost-effective strategy for 2D material production, involving a dispersion containing a permeating solute (graphene), a fouling material (non-exfoliated graphite), and the solvent. The objective of the model is to investigate the effects of fouling of flat layered structure material (graphite) on the transmembrane pressure (TMP) of the system and the filtration of the permeating solute. COMSOL Multiphysics software was used to numerically solve the coupled Navier–Stokes and mass conservation equations to simulate the flow and mass transfer in the two-dimensional domain. For the TMP calculations, we used the resistance-in-series approach to link the fouling of the foulants to the TMP behavior. The foulant particles were assumed to form a polarization layer and cake on the membrane surface, leading to the increment of the TMP of the system. We also assumed the wettability of the polymeric membrane’s inner wall increases upon fouling due to the flat layered structure of the foulant, which results in the reduction in the TMP. This approach accurately reproduced the experimental TMP behavior with a Mean Absolute Error (MAE) of 0.007 psi. Furthermore, the permeation of the permeating solute was computed by incorporating a fouling-dependent membrane partition coefficient for these particles. The effects of the concentration polarization and cake formation fouling stages on the membrane partition coefficient were encapsulated into our defined model parameters, denoted as α and β, respectively. This formulation of the partition coefficient yielded permeate concentration profiles, which are in excellent agreement with the experiments. For three feed concentrations of 0.05, 0.1, and 0.3 g/L, our model reproduced the experimental permeate concentration profiles with MAEs of 0.0002, 0.0003, and 0.0022 g/L, respectively. The flexibility of this model enables the users to utilize the size and concentration-dependent α and β parameters and optimize their experimental microfiltration setups effectively.