Latent Heat Research Articles

Modification of steel slag to prepare chlorides based composite phase change materials with shape stability for high-temperature thermal energy storage

Using steel slag to prepare high-temperature (>500 °C) PCMs was an effective way to achieve its high value-added utilization as a potential heat storage medium in a variety of applications, such as solar energy storage, power peak shaving, and industrial waste heat recovery. However, the complex solid waste of steel slag might be corrosive to salt-based PCMs at high temperature. To address this issue, steel slag was firstly modified with another solid waste (i.e., CFA), which was then used to microencapsulate NaCl-KCl to prepare shape-stabilized C-PCMs in this work. Thermophysical and mechanical properties of C-PCMs were analyzed. Results showed that CFA modification greatly improved chemical compatibility between steel slag and eutectic salt through phase reconstruction. Steel slag modified with 30 wt% CFA at 1100 °C was identified as the optimum skeleton. The prepared C-PCMs containing 50 wt% salt showed a phase transition temperature of 653 °C with a high latent heat of 139 J/g and an excellent cycling stability. Additionally, its thermal conductivity reached 1.46 W/(m·K), 180 % higher than of pure salt. Compressive strength of the composite could be as high as 119 MPa, superior to other salt-based C-PCMs. A heat storage device was further designed to allow the numerical investigation of thermal performance of the prepared C-PCMs in practical conditions. Attributed by reasonable arrangement of bricks, the heat storage device possessed a uniform temperature distribution over the vertical cross-section of HTF, which contributed to a quick completion of charging and discharging process. This work could potentially lay a foundation for application of steel slag in the field of high-temperature thermal energy storage.

Energy storage density enhancement in paraffin phase change material emulsions: A comparative study with two different base fluids

This investigation examined the thermophysical properties of emulsions comprising paraffin 56/58 phase change material (PCM) dispersed in water and ethylene glycol (60 wt%) aqueous solution to optimize energy storage density for low-temperature thermal applications. Dynamic Light Scattering analysis revealed a uniform dispersion of paraffin 56/58 PCM droplets in the basefluids, with an average diameter of approximately 150 nm achieved by incorporating sodium dodecyl sulfate surfactant. The latent heat of fusion for emulsions containing paraffin 56/58 PCM in ethylene glycol (60 wt%) exhibited values of 37.5/41.7, 58.5/63.9, 73.8/75.43, and 93/90.25 J/g for concentrations of 20, 30, 40, and 50 wt%, respectively, during melting/solidification phases. Furthermore, the highest energy storage densities of 306.95 and 361.3 kJ/kg were attained at a PCM concentration of 50 wt% in ethylene glycol (60 wt%) and water-based emulsions, respectively, surpassing those of similar working fluids. It is also indicated that water-based paraffin 56/58 PCMs offer superior energy storage density. However, under severe operating conditions such as extreme temperatures, ethylene glycol (60 wt%) based paraffin 56/58 emulsions demonstrate greater suitability, as the evaporation and freezing points of the basefluid can be adjusted by modulating the ethylene glycol concentration ratio.

Intercomparison of eddy-covariance software for urban tall-tower sites

Abstract. Long-term tall-tower eddy-covariance (EC) measurements have been recently established in three European pilot cities as part of the ICOS-Cities project. We conducted a comparison of EC software to ensure a reliable generation of interoperable flux estimates, which is the prerequisite for avoiding methodological biases and improving the comparability of the results. We analyzed datasets covering 5 months collected from EC tall-tower installations located in urbanized areas of Munich, Zurich, and Paris. Fluxes of sensible heat, latent heat, and CO2 were calculated using three software packages (i.e., TK3, EddyPro, and eddy4R) to assess the uncertainty of flux estimations attributed to differences in implemented postprocessing schemes. A very good agreement on the mean values and standard deviations was found across all three sites, which can probably be attributed to a uniform instrumentation, data acquisition, and preprocessing. The overall comparison of final flux time series products showed a good but not yet perfect agreement among the three software packages. TK3 and EddyPro both calculated fluxes with low-frequency spectral correction, resulting in better agreement than between TK3 and the eddy4R workflow with disabled low-frequency spectral treatment. These observed flux discrepancies indicate the crucial role of treating low-frequency spectral loss in flux estimation for tall-tower EC systems.

Debris cover effects on energy and mass balance of Batura Glacier in the Karakoram over the past 20 years

Abstract. The influence of supraglacial debris cover on glacier mass balance in the Karakoram is noteworthy. However, understanding of how debris cover affects the seasonal and long-term variations in glacier mass balance through alterations in the glacier's energy budget is incomplete. The present study coupled an energy–mass balance model with heat conduction within debris layers on debris-covered Batura Glacier in Hunza Valley to demonstrate the influence of debris cover on glacial surface energy and mass exchanges during 2000–2020. The mass balance of Batura Glacier is estimated to be -0.262±0.561 m w.e. yr−1, with debris cover accounting for a 45 % reduction in the negative mass balance. Due to the presence of debris cover, a significant portion of incoming energy is utilized for heating debris, leading to a large energy emission to the atmosphere via thermal radiation and turbulent sensible heat. This, in turn, reduces the melt latent heat energy at the glacier surface. We found that the mass balance exhibits a pronounced arch-shaped structure along the elevation gradient, which is associated with the distribution of debris thickness and the increasing impact of debris cover on the energy budget with decreasing elevation. Through a comprehensive analysis of the energy transfer within each debris layer, we have demonstrated that the primary impact of debris cover lies in its ability to modify the energy flux reaching the surface of the glacier. Thicker debris cover results in a smaller temperature gradient within debris layers, consequently reducing energy reaching the debris–ice interface. Over the past 2 decades, Batura Glacier has exhibited a trend towards less negative mass balance, likely linked to a decrease in air temperature and reduced ablation in areas with thin or sparse debris cover.

Thermophysical characterization and reliability analysis of binary composite nano doping on stearic acid-acetamide eutectic PCM

Organic phase change materials (PCM) have been extensively studied and employed for thermal energy storage applications, especially in the last decade. Wide range of melting temperature with high latent heat of fusion and absence of super cooling have made them highly desirable for energy storage applications, yet their intrinsic low thermal conductivity has been a major drawback in practical implementation. This study intends to address this and study the thermophysical characteristics of an organic PCM through composite nano doping. Stearic acid-acetamide eutectic PCM with a melting temperature of 65.73 °C and a latent heat of 203.72 J/g, was incorporated with a binary blend of Aluminum Oxide nanoparticles and multi-walled carbon nanotubes (MWCNT). The addition of metallic oxide and carbonaceous nanoparticles increased the melting temperature of the eutectic mixture by 2.9 °C and a highly advantageous increment in latent heat of fusion by 10% was observed, due to the improved molecular interaction introduced by the nanoparticles. Composite nano doping enhanced the thermal conductivity of the eutectic PCM by a 132.7% and also resulted in high optical absorption properties. The prepared eutectic mixtures were chemically stable and the eutectic PCM showed an improved final degradation temperature and thermal stability, with composite nano doping. Thermal reliability was analyzed through accelerated thermal cycling test and the eutectic mixtures could retain their thermal characteristics and chemical stability even after 500 thermal cycles. Composite nano doping proved to be a reliable thermophysical characteristics enhancement technique for organic eutectic PCM.

Micro-PINGUIN: microtiter-plate-based instrument for ice nucleation detection in gallium with an infrared camera

Abstract. Ice nucleation particles play a crucial role in atmospheric processes; for example, they can trigger ice formation in clouds and thus influence their lifetime and optical properties. The quantification and characterization of these particles require reliable and precise measurement techniques. In this publication, we present a novel droplet freezing instrument to measure the immersion freezing of biotic and abiotic ice-nucleating particles within the temperature range of 0 to −25 °C. Immersion freezing of the samples is investigated using 384-well PCR plates with a sample volume of 30 µL. Nucleation events are detected with high precision using a thermal camera that records the increase in infrared emission due to the latent heat release. To maximize the thermal contact between the PCR plate and the surrounding cooling unit, we use a gallium bath as a mount for the PCR plate. The instrument was validated relative to a calibrated temperature standard and through reproducibility measurements employing the same suspension. We find that the combination of good thermal connectivity and precise temperature recording enables accurate (±0.81 °C at −10 °C) and reproducible (±0.20 °C) detection of the nucleation temperatures. Consequently, the results that are produced using the MICROtiter-Plate-based instrument for Ice Nucleation detection in GalliUm with an INfrared camera (micro-PINGUIN) are of good quality and the instrument can be used to study the immersion freezing of various ice-nucleating particles. For comparison with already existing instruments, Snomax® (hereafter Snomax) and illite NX suspensions are measured with the new ice nucleation instrument, micro-PINGUIN. Further, we investigated the reproducibility of experiments using Snomax suspensions and found poor reproducibility when suspensions were prepared freshly even if the same batch of Snomax is used. This could be attributed to substrate heterogeneity, aging effects, and dilution errors. The reproducibility of the measurements is greatly improved for Snomax suspensions that are prepared in advance and stored frozen in aliquots. Thus, we suggest the use of suspensions frozen in aliquots for further reproducibility measurements and intercomparison studies.

High thermal conductivity composite phase change material with Zn2+ metal organic gel and expanded graphite for battery thermal management

Phase change materials (PCMs) with promising potential thermal energy is stored and released much thermal energy during phase change process, which has greatly prospect in building energy conservation, waste heat recovery, energy storage, electrical vehicles (EVs) and other fields. Nevertheless, the low thermal conductivity and easy leakage of PCM is still a challenge to restrict its fasting development. Traditional supporting material is hard to reconcile antileakage and thermal conductivity of composite PCM (CPCM). Herein, the polyethylene glycol (PEG) with three-dimensional Zn2+ metal–organic gel (ZnHGL) as high-thermal conductivity support framework, styrene–butadiene–styrene block copolymer (SBS) and expanded graphite (EG) has been designed and prepared PZSE with high thermal conductivity, accompany with double transferring heat and supporting network structure. In contrast with pure PEG, the thermal conductivity of PZSE2 is increased by obvious 8.7 times when Zn2+ metal–organic gel and SBS with the proportion of 1:1, the mass maintenance rate and latent heat storage capacity are increased to 99.5 % and 103.64 J/g, respectively. Further, the thermal imaging camera indicate that PZSE2 exhibit a stable temperature-regulation property, which is benefited to extend the time to adjust the temperature. Additionally, the maximum temperature and temperature differential of the battery module with PZSE2 can be maintained within 60 °C and 6 °C, respectively, even at 1.5C discharge rate after ten cycling process. It indicates that the battery module with PZSE2 has optimum thermal management effect. Therefore, PZSE with metal–organic gel and EG can provide a promising candidate utilization in thermal regulation of EVs and energy storage.

Preparation and characterization of phase change material emulsions and their applications in liquid cooling systems for wind turbines

In order to improve the effect of liquid cooling system for wind turbine, this study used ultrasonic preparation method, stearic acid as phase change material, sorbitan trioleate and sodium lauryl sulfate as compound surfactants successfully prepared stearic acid phase change material emulsion as a cooling medium for investigation. The characterization, thermophysical properties, and fluidity of stearic acid phase change material emulsions at varying concentrations were examined through differential scanning calorimetry, thermal constant analysis, and viscometry. To investigate the cooling effects, a stator axial liquid cooling model was developed for both water and a 14 % stearic acid phase change material emulsion. Findings revealed that the 14 % stearic acid phase change material emulsion exhibited a latent heat of phase change of 22.5 J/g, reaching a peak melting temperature of 68.7 °C. Additionally, the latent heat of solidification was measured at 21.08 J/g, accompanied by a peak solidification temperature of 60.3 °C. The maximum thermal conductivity reached 0.5801 W/(m·K), and the specific heat capacity peaked at 5219.8 J/(K·mol), marking a notable improvement of 1.26 times. Under an inlet temperature of 30 °C and a flow rate of 1 L/min, stearic acid phase change material emulsion effectively lowered the temperatures of the windings, stator, rotor, and casing by 19.2 °C, 23.6 °C, 19.2 °C, and 9.6 °C, respectively. stearic acid phase change material emulsion demonstrates excellent temperature control effectiveness at 3600 r/min and a low flow rate of 1 L/min, showcasing efficient energy utilization efficiency.

Preparation and properties of gel-type low-temperature phase change materials

In the context of the dual‑carbon target, there is a high emphasis on the energy efficiency of traditional mechanical cold storage systems with significant power consumption. Additionally, the implementation of time-of-use electricity pricing has played a crucial role in driving the rapid advancement of energy storage technology. The application of energy storage technology in cold storage can significantly reduce the energy consumption of the refrigeration system, save operating costs by shifting peak demand to valleys, and reduce start and stop frequencies. Therefore, studying phase-change materials with high latent heat, low cost, and good performance for cold storage is of great practical application in cold storage. The paper developed four types of gel-type phase-change cold storage materials with high latent heat, low cost, and good cycle stability. These materials mainly consist of NH4Cl, KCl, and deionized water. The phase transition temperature ranges from −18 to −21 °C, the latent heat of phase change is approximately 260 to 289 J/g, and the thermal conductivity ranges from 0.58 to 0.60 W/(m·K), which can meet the cooling demand of cold storage facilities. Furthermore, by comparing the phase transition temperature, latent heat value of phase change, and cyclic stability, a gel-type PCM with good comprehensive properties was selected for corrosion and corrosion inhibition studies with five common metal samples in welded and non-welded forms. The results showed that material B2 had slight corrosion on 1060 aluminum, 6061 aluminum, and 304 stainless steels, but no obvious corrosion phenomenon was found on 316 stainless steels. The corrosion rate of the material on red copper was the highest, and the corrosion was too strong. In addition, the corrosion of welded parts is more serious than that of non-welded parts, and the welding points are more susceptible to corrosion. Adding the corrosion inhibitor BTA to material B2 can reduce the corrosion rate of red copper by more than 94 %.

On the thermodynamics of DNA double strand in the Peyrard-Bishop-Dauxois model

The temperature dependence of energy, partition function, entropy and free energy, describing a first-order-like phase transition of a DNA molecule is calculated based on the direct method of molecular dynamics for the classical Peyrard-Bishop-Dauxois model. It is shown that without taking into account the quantum freezing of the degrees of freedom at low temperatures, the relationship between these quantities is not determined. The latent heat of DNA melting is calculated for homogeneous PolyA/PolyT and PolyG/PolyC DNA chains. It is shown that this melting transition corresponds to a sharp temperature dependence of the heat capacity.

Structure Design and Heat Transfer Performance Analysis of a Novel Composite Phase Change Active Cooling Channel Wall for Hypersonic Aircraft.

Efficient and stable heat dissipation structure is crucial for improving the convective heat transfer performance of thermal protection systems (TPSs) for hypersonic aircraft. However, the heat dissipation wall of the current TPS is limited by a single material and structure, inefficiently dissipating the large amount of accumulated heat generated during the high-speed maneuvering flight of hypersonic aircraft. Here, a convection cooling channel structure of TPS is proposed, which is an innovative multi-level structure inspired by the natural honeycomb. An active cooling channel (PCM-HC) is designed by using a variable-density topology optimization method and filled with phase change material (PCM). Numerical simulations are used to investigate the thermal performance of the PCM-HC wall, focusing on the influence of PCM properties, structural geometric parameters, and PCM types on heat transfer characteristics. The results demonstrate that the honeycomb-like convection cooling channel wall, combined with PCM latent heat of phase change, exhibits superior heat dissipation capability. With a heat flux input of 50 kW/m2, the maximum temperature on the inner wall of PCM-HC is reduced by 12 K to 20 K. Different PCMs have opposing effects on heat transfer performance due to their distinct thermophysical properties. This work can provide a theoretical basis for the design of high-efficiency cooling channel, improving the heat dissipation performance in the TPS of hypersonic aircraft.

Role of aloe vera based nanofluids for cool thermal energy storage system: A comparative study

The present experimental investigation incorporates the preparation of aloe vera gel-based phase change nanofluid (NFPCM) for a cool thermal energy storage (CTES) system. Two sets of NFPCMs were produced by adding graphene nanoplatelets (GNP) in deionized water and aloe vera gel (0.20 wt%, 0.40 wt%, and 0.60 wt%). The zeta potential analysis shows that the NFPCM with aloe vera gel is more stable even after 60 days from the preparation (−44 mV). The thermal conductivity of NFPCMs was analyzed through the transient hot wire method and the enhancement of 42 %, and 37.5 % were measured in the ice phase for NFPCMs with aloe vera gel and DI water (0.60 wt%) respectively at the heat transfer fluid temperature of −15 °C. The NFPCMs with aloe vera gel show that the addition of GNP prepended the peak melting temperature from −16 °C to −10.5 °C, which is due to the quick formation of nuclei as compared to NFPCMs with DI water. Additionally, a slight reduction in the latent heat of only 7 % was observed. The charging characteristics of NFPCMs were studied in a single spherical capsule at −8 °C. The maximum reduction in total charging time of 25 % was recorded for the aloe vera gel-based NFPCM with a maximum concentration of GNP (0.60 wt%). The green synthesis of aloe vera gel-based NFPCM exhibited noteworthy enhancements in thermophysical properties. Additionally, it was observed that the long-term stability of the NFPCM was achieved by excluding surfactants during the preparation process. The incorporation of graphene nanoplatelets (GNP) into aloe vera gel as the foundational phase change material (PCM) facilitates the partial charging of the CTES system with a reduced energy input.

Numerical study of thermal performance of a PCM in a modifying tube-bundle latent heat thermal storage

The main aim of this study is to numerically investigate the thermal performance of a newly designed modifying tube-bundle Latent Heat Thermal Storage (LHTS). The new LHTS design proposed a half-cylindrical tube attached to the Heat Transfer Fluid tube, which implies making the PCM indirect contact with the HTF tube. This reduces the heat transfer resistance by eliminating the metal construction of the tubes. For this purpose, a 3D numerical model was developed based on mass, momentum and energy conservations using ANSYS Fluent software. After validating the model developed by comparing numerical results with those obtained experimentally by a published study, the PCM liquid fraction and amount of power stored during the melting and solidification were studied. Water and lauric acid as a working fluid and PCM were implemented in the model. In addition, three different Heat Transfer Fluid (HTF) inlet temperatures 15°C,20°Cand25°C, and HTF’s flow rates in terms of Reynolds number 1000,1500and2000 were tested. The thermal behaviour of the present LHSU design was compared with that of the same volume double pipe LHTS unit. Results showed that the melting and solidification processes of the proposed storage were very uniform, with convection and conduction heat dominating PCM melting and solidification, respectively. The increase in the heat transfer contact area between the HTF and the tube bundle contributed significantly to the PCM melting and solidification acceleration, making each tube bundle behave as a single storage unit. Therefore, the time required for complete melting and solidifying of the PCM was half (50%) of the time needed for the same amount in the double pipe LHTS. Similarly, the melting and solidification time in the preset storage was shortened by about 22% and 41.6%, respectively, compared with the regular tube LHTS unit.

Solar regenerated carbon-based composite desiccant coated heat exchangers for air dehumidification

Desiccant dehumidification can realize decoupling of latent and sensible heat loads in dehumidified air conditioning, thereby reducing energy consumption. This paper proposes a solar regenerated carbon-based composite desiccant coated heat exchangers (DCHE) for air dehumidification. Carbon-based composite desiccant is electrostatically sprayed onto the surface of the heat exchanger to form a dehumidification coating. An experimental system for evaluating the dehumidification and regeneration performance of DCHE is established. The Taguchi method is employed to evaluate the impact of operating parameters such as air velocity, water flow rate, and regeneration temperature on the dehumidification and regeneration efficiency of DCHE. The result shows that air velocity is the primary factor impacting the dehumidification performance of DCHE, with regeneration temperature and cooling water flow rate following in importance. With the faster air velocity and the lower cooling water flow rate, DCHE shows the better dehumidification performance. Moreover, excessively both high and low regeneration temperatures can result in a degradation in the dehumidification performance of DCHE. Under optimal operating conditions, the dehumidification rate (EDE) and thermal coefficient of performance (COPth) of DCHE can reach 7.5 kg/h and 2.3, respectively. The moisture content of the air reduces from 19.6 g/kg to 8.0 g/kg.

Eutectic phase change composites with MXene nanoparticles for enhanced photothermal absorption and conversion capacity

Phase change composite materials with uniform nanomaterial dispersion are potential solutions for improving thermophysical properties and enhancing latent heat capacity applicable in thermal management. In this study, various transitional carbide-based MXene samples were synthesised via acid etching to augment the heat transfer capacity and efficiency of the solar thermal energy storage (TES). These samples were then uniformly dispersed in a eutectic mixture (1:1) of paraffin wax (PW) and polyethylene glycol (PEG-6000), resulting in the formation of a MePCM composite. The controllable porous structure and hydrogen interactions with the external layer of MXene and long-chain PCM benefitted in the well impregnation of PCM and compatibility impregnated into the composite. An exceptionally higher mass fraction of 1 wt % Ti3C2Tx MXene-based phase change composite unveiled a higher phase change enthalpy of 138.66 J/g in the melting phase and 139.54 J/g in the solidification phase with 89.82 % energy storage efficiency. In contrast to pure eutectic PCM (0.2593 W/mK), the thermal conductivity of MePCM composite is relatively higher and provides a thermal conductivity of 0.9209 W/mK for Ti3C2Tx MXene-based composite. The enhancement of thermal conductivity is ascribed to the increased heat conduction pathway facilitated by the MXene arrangement. The utilisation of spatially constrained eutectic phase change material (PCM) assembly resulted in the development of MePCM, which exhibited enhanced thermal conductivity, chemical and physical stability, and thermal consistency across 500 melting-solidification cycles. Benefitting from the thermal conduction path, the MePCM exhibits an excellent photothermal conversion efficiency of 98.53 %. The thermal responsive tests of Ti3C2Tx and V2CTx MXene composite samples provide better thermal response than eutectic PCM without thermal reduction. With a higher thermal storage capacity and higher heat transfer property, thermally reliable MePCM composites exhibited tremendous potential for photothermal applications.

Effects of operating parameters on start performance of compression ignition engine by using high-pressure direct-injection pure methanol fuel

Methanol was one of the research hotspots in internal combustion engines over recent years. The application of methanol is a promising approach to transport decarbonization due to low carbon content. However, the utilization of methanol in compression ignition (CI) engines faces some challenges as a result of low reactivity and high latent heat of vaporization, such as cold start and operation stability. Furthermore, the impact mechanisms of operating parameters on cold start and operation stability in CI engine have not been understood deeply. In this work, the effects of operating parameters on average cycle of start and coefficient of speed variation (CoVspeed) of idle were studied on a CI engine fueled by pure methanol fuel. Results show that the injection strategy of the minimum average starting cycle number is the pre-main injection, which includes lower injection pressure, −4 °CA ATDC (degree crank angle after top dead center) main timing, smaller pre mass, and larger pre-main interval. The injection strategy of the minimum CoVspeed of idle is the pilot-pre-main injection, which includes lower injection pressure, −4 °CA ATDC main timing, smaller pre mass, larger pre-main interval, smaller pilot mass, and shorter pilot-main interval. Under the same operating conditions, the average cycle of start is 12 and 5 for methanol and diesel respectively. The CoVspeed of idle is 6.72% and 0.53% for methanol and diesel respectively. When coolant temperature is 30 °C, the minimum intake temperature is 120 °C. Upon adjusting the coolant temperature to 80 °C, the minimum intake temperature decreases to 80 °C.

Experimental Study on the Effect of Different HTF Discharges to Increase Efficiency of a Latent Heat Storage System Using a Spiral Coil Heat Exchanger with Different Fins

Experimental Study on the Effect of Different HTF Discharges to Increase Efficiency of a Latent Heat Storage System Using a Spiral Coil Heat Exchanger with Different Fins

Analysis and comparative assessment of charging dynamics in vertical multi-channel latent heat storage system with corrugated wavy channels

Latent heat thermal energy storage (LHTES) is a promising technology, but thermal response limitations caused by the relatively poor thermal conductivity of phase change materials (PCMs) remains an issue. In recent years, computational fluid dynamics (CFD) has proven to be a powerful and reliable tool in design optimization of different systems and problems in the energy sector. Building on that, the present work will use CFD to investigate the thermal performance enhancements achieved using vertical double-tube LHTES systems with multi-channel sinusoidal wavy geometries. The main parameters investigated here are the wavy channel height (H), pitch (P) and the number of channels (N) and the results are assessed in terms of melting rates and heat transfer coefficients. The analysis found that increasing the height from 1 mm to 3 mm, accelerated the phase change by 21 %, while reducing the pitch from 12.5 mm to 5 mm, enhanced the heat storage rates by 28 %. In addition, increasing the number of channels from 3 to 7 improved the charging rate by 64 %. Compared to a conventional straight channel, the enhanced wavy channel (N = 7, H = 3 mm, P = 5 mm) achieved 80 % higher thermal storage rate and 42 % faster charging time. The above findings provide new insight into the potential of utilizing compact vertical LHTES systems via customized wavy channels, with significant impact towards enhancing the existing thermal energy storage systems.

Preparation and thermal performance study of a novel hydrated salt composite PCM for space heating

In order to effectively address the mismatch between thermal energy supply and demand in buildings, latent heat storage (LHS) based on phase change material (PCM) stands out as a key technology. While hydrated salt has emerged as a promising PCM, it encounters common issues such as substantial supercooling, phase separation, and low thermal conductivity, hindering its development. To mitigate these limitations, this study focused on modifying Ba(OH)2·8H2O by incorporating various nucleating agents and thickening agents to reduce supercooling, enhancing the composite PCM's thermal properties by introducing expanded graphite (EG) to elevate thermal conductivity. Subsequently, the thermal stability of the PCM was evaluated through accelerated thermal cycling tests, encompassing the assessment of critical thermal parameters, including supercooling degree, enthalpy, and thermal conductivity of the composite PCM. Experimental findings unveiled the effectiveness of incorporating 2 wt% BaCl2·2H2O and 1 wt% CMC to Ba(OH)2·8H2O, effectively diminishing the supercooling degree from 14 °C to 1.42 °C. Further integration of 3.5 wt% EG led to a substantial decrease in the supercooling degree to 0.24 °C. Simultaneously, the addition of EG resulted in an improvement in thermal conductivity, elevating it from 0.62 W/(m·K) to 1.03 W/(m·K), while the enthalpy decreased from 283.68 J/g to 252.81 J/g. Notably, the composite PCM exhibited notable thermal reliability with a latent heat drop of 15.9 % following 1000 accelerated cycles of testing. Moreover, the composite PCM demonstrated superior thermal storage density, measuring at 2.36 times that of traditional paraffin wax, yet with a thermal storage cost merely a quarter of paraffin wax, rendering it more favorable for extensive deployment in building energy systems.

Performance evaluation and optimization of compact tube-fin latent heat storage system in phase change nanoemulsion discharge mode

The low thermal conductivity of phase change materials (PCMs) and the reduced heat transfer temperature difference along a tube both limit the thermal performance of latent heat thermal energy storage (LHTES). Herein, a compact tube-fin LHTES system based on phase change nanoemulsions was developed and the heat transfer process of nanoemulsion and PCM was numerically investigated. The effects of the heat transfer structure of the heat exchanger and the thermophysical parameters of the heat transfer fluid (HTF) on the cold energy discharge performance of the system were quantified. The optimized model reduced the discharge time by 24.4 % in nanoemulsion mode relative to water. Heat transfer improvement on the PCM side could be achieved by decreasing the fin spacing and tube spacing and by increasing the fin thickness. Such improvement reinforced the heat transfer enhancement of the nanoemulsion. The heat transfer mechanism was explained by the temperature distributions of the HTF and PCM along the tube. The phase-change thermostatic properties of the nanoemulsion and PCM contributed to the formation of dual-phase-change coupled heat transfer (i.e., the heat transfer process when the fluid inside the tube and the PCM filled outside the tube undergo a simultaneous phase change) within the LHTES, increasing the heat transfer temperature difference and the magnitude of the driving force. Increasing the phase change temperature difference accelerated the onset of dual-phase-change heat transfer, while increasing the PCM content prolonged the process. Briefly, this study provided operational and design assistance for LHTES systems in nanoemulsion mode with the intention to accelerate heat transfer rates.