Laser Scanning Microscopy Research Articles

Rheological Investigation of Highly Filled Copper(II) Oxide Nanosuspensions to Optimize Precursor Particle Content in Reductive Laser-Sintering

In this article, the particle concentration of finely dispersed copper(II) oxide nanosuspensions as precursors for reductive laser sintering (RLS) is optimized on the basis of rheological investigations. For this metallization process, a smooth, homogeneous and defect-free precursor layer is a prerequisite for adherent and reproducible copper structures. The knowledge of the rheological properties of an ink is crucial for the selection of a suitable coating technology as well as for the adjustment of the ink formulation. Different dilutions of the nanosuspension were examined for their rheological behavior by recording flow curves. A strong shear thinning behavior was found and the viscosity decreases exponentially with increasing dilution. The viscoelastic behavior was investigated by a simulated doctor blade coating process using three-interval thixotropy tests. An overshoot in viscosity is observed, which decreases with increasing thinning of the precursor. As a comparison to these results, doctor blade coating of planar glass and polymer substrates was performed to prepare precursor layers for reductive laser sintering. Surface morphology measurements of the resulting coatings using laser scanning microscopy and rheological tests show that homogeneous precursor layers with constant thickness can be produced at a particle–solvent ratio of 1.33. A too-high particle content results in an irregular coating layer with deep grooves and a peak-to-valley height Sz of up to 7.8 μm. Precise dilution control allows the fabrication of smooth surfaces with a Sz down to 1.5 μm.

Adsorption and inhibition of rosin thiourea imidazole quaternary ammonium salt on steel surface in HCl solution

Rosin thiourea imidazole quaternary ammonium salt (RTIQAs) was synthesized by connecting rosin and imidazole units via thiourea linker, and its inhibitive action on the corrosion of CRS (cold rolled steel) in 1.0 M HCl solution was fully investigated. The results demonstrate that RTIQAs is an efficient mixed-type inhibitor with the maximum inhibition efficiency of 95%. The adsorption rule on the CRS surface fully complies with Langmuir isotherm. The efficient inhibition of RTIQAs can also be verified by AFM, SEM and CLSM (confocal laser scanning microscope). The direct adsorption proof of RTIQAs molecules on steel surface can be further presented in EDX and XPS.

In situ study of microstructural evolution of borosilicate glass–sulfate mixture at high temperatures

AbstractMicrostructural evolution of borosilicate glass–sulfate (BaSO4 or Na2SO4) mixture was observed in situ using a high‐temperature confocal scanning laser microscope. The phase compositions and sulfate retention of the mixture at different temperatures were also examined. The results indicate that for the glass–BaSO4 sample (abbreviated as BS), the borosilicate glass begins to melt at about 900°C, and the triangular BaSO4 crystals grow obviously between 900°C and 1100°C. At temperatures above 1100°C, the BaSO4 crystals gradually melt and decompose. For the glass–Na2SO4 sample (abbreviated as NS), strip‐shaped BaSO4 crystals begin to form at about 820°C after the borosilicate glass melting, and then gradually melt with further increasing temperature. When the temperature increases to 1000°C, the upper layer of the NS sample possesses Na2SO4, LiNaSO4, and BaSO4 phases, while the lower layer possesses an amorphous phase. Moreover, the SO3 retention in the BS sample remains almost unchanged with temperature increases from 900°C to 1100°C, and then decreases with further increasing temperature. The SO3 retention retained in the NS sample decreases rapidly at temperatures above 900°C. These findings can provide a guidance for vitrifying sulfur‐rich high‐level liquid waste.

High glucose-induced p66Shc mitochondrial translocation regulates autophagy initiation and autophagosome formation in syncytiotrophoblast and extravillous trophoblast.

p66Shc, as a redox enzyme, regulates reactive oxygen species (ROS) production in mitochondria and autophagy. However, the mechanisms by which p66Shc affects autophagosome formation are not fully understood. p66Shc expression and its location in the trophoblast cells were detected in vivo and in vitro. Small hairpin RNAs or CRISPR/Cas9, RNA sequencing, and confocal laser scanning microscope were used to clarify p66Shc's role in regulating autophagic flux and STING activation. In addition, p66Shc affects mitochondrial-associated endoplasmic reticulum membranes (MAMs) formation were observed by transmission electron microscopy (TEM). Mitochondrial function was evaluated by detected cytoplastic mitochondrial DNA (mtDNA) and mitochondrial membrane potential (MMP). High glucose induces the expression and mitochondrial translocation of p66Shc, which promotes MAMs formation and stimulates PINK1-PRKN-mediated mitophagy. Moreover, mitochondrial localized p66Shc reduces MMP and triggers cytosolic mtDNA release, thus activates cGAS/STING signaling and ultimately leads to enhanced autophagy and cellular senescence. Specially, we found p66Shc is required for the interaction between STING and LC3II, as well as between STING and ATG5, thereby regulates cGAS/STING-mediated autophagy. We also identified hundreds of genes associated several biological processes including aging are co-regulated by p66Shc and ATG5, deletion either of which results in diminished cellular senescence. p66Shc is not only implicated in the initiation of autophagy by promoting MAMs formation, but also helps stabilizing active autophagic flux by activating cGAS/STING pathway in trophoblast.

Phytometabolome of Psidium guajava inhibits biofilm formation of Escherichia coli and augmented acute wound repair

Psidium guajava is an equatorial fern tree and nutritive plant with medicinal properties including antimicrobial, antioxidant, antitumor, anti-inflammatory activities, etc., In the present study, the untargeted phytometabolome of ethyl acetate and acetone extracts of P. guajava showed 107 compounds were identified using UPLC-ESI-Q-TOF-MSE analysis and assessed for anti-biofilm activity using various assays. The results clearly indicated that the ethyl acetate and acetone extracts significantly inhibit the growth and obliterate the metabolic activity of E. coli. The confocal laser scanning microscope (CSLM) analysis also confirmed the biofilm inhibitory activity of extracts against E. coli. Further, the ethyl acetate and acetone extracts displayed significant wound healing activity in BALB/c mice than the control treatment. The Doppler imaging analysis depicted that the extracts increase the blood circulation towards the wound to accelerate wound repair. Together, the UPLC-Q-TOF-MSE analysis clearly showed the metabolomics profiling of P. guajava and these metabolomes could be responsible for their potential biofilm obliterating and augmenting acute wound repair.

Characterisation of a casein-/whey protein concentrate–Antarctic krill oil emulsion system and improvement of its storage stability

Aims To develop Antarctic krill oil emulsions with casein and whey protein concentrate (WPC) and study their physicochemical properties and storage stability. Methods Emulsions were prepared by homogenisation and ultrasonication. The properties of the emulsions were investigated via ultraviolet ray spectroscopy, dynamic light scattering, confocal laser scanning microscope, sodium dodecyl sulphate–polyacrylamide gel electrophoresis, Fourier transform infra-red spectrometer, and fluorescence spectrum. Shelf life was predicted by the Arrhenius model. Results Casein- and WPC-krill oil emulsions were well formed; the mean particle diameters were less than 128.19 ± 0.64 nm and 158 ± 1.56 nm, the polymer dispersity indices were less than 0.26 ± 0.01 and 0.27 ± 0.01, and the zeta potential were around −46.88 ± 5.02 mV and −33.51 ± 2.68 mV, respectively. Shelf life was predicted to be 32.67 ± 1.55 days and 29.62 ± 0.65 days (40 °C), 27.69 ± 1.15 days and 23.58 ± 0.14 days (50 °C), 24.02 ± 0.15 days and 20.1 ± 0.08 days (60 °C). Conclusion The prepared krill oil emulsions have great potential to become a new krill oil supplement.

Comparative Study on the Emulsification of Octenyl Succinic Anhydride Modified Sweet Potato Starch: As Macromolecular and Particulate Stabilizers

AbstractSweet potato is one of the essential starch materials for food and feed world widely. However, its application is limited by the low viscosity and poor stability of native starches. Herein, sweet potato starch is modified by octenyl succinic anhydride (OSA) in the aqueous system. The optimization for esterification is studied using response surface methodology. The characteristics of OSA‐modified sweet potato starch are investigated, and its emulsifying properties as macromolecular and particulate stabilizers in the oil‐in‐water systems are compared. The optimal process conditions for OSA modification are: reaction time 4.0 h, temperature 38.8 °C, pH of the reaction system 8.2, starch concentration 32.2%, OSA amount 3.0%. The degree of substitution is 0.0185, and reaction efficiency is 79.7% under the optimum conditions. The new peaks at 1725 and 1573 cm−1 are observed by Fourier transform infrared spectroscopy. Compared with native starch, OSA‐modified sweet potato starch exhibits higher viscosities, improved paste clarity, and decreased retrogradation. The confocal laser scanning microscope results show that the gelatinized starch macromolecule and ungelatinized starch particles can arrange at the water–oil interface. The OSA‐modified sweet potato starch is both an effective macromolecular emulsifier and a particulate stabilizer, effectively stabilizing oil‐in‐water emulsions.

Trueness, physical properties, and surface characteristics of additive-manufactured zirconia crown

ObjectiveThis study aimed to conduct a comparison of trueness and physical and surface properties among five distinct types of additive manufactured (AM) zirconia crowns and zirconia crowns produced using the subtractive manufacturing (SM). Material and methodsZirconia crowns were fabricated using five distinct techniques, each varying in the method of slurry transfer and photocuring source. Each experimental group utilized either one of the four digital light processing (DLP)-based techniques (DLP spreading, DLP spreading gradation, DLP vat and DLP circular spreading) or the stereolithography (SLA)-based technique (SLA spreading). The control (CON) group employed SM. To assess accuracy, trueness was measured between the scan and reference data. To analyze the physical properties, voids were examined using high-energy spiral micro-computed tomography scans, and the crystal structure analysis was performed using X-ray diffraction (XRD). Surface roughness was assessed through laser scanning microscopy. ResultsDifferences in the trueness of internal surfaces of crowns were found among the groups (P < 0.05). Trueness varied across the measurement surfaces (occlusal, lateral, and marginal) in all the groups except for the DLP spreading gradation group (P < 0.05). Voids were observed in all AM groups. All groups showed similar XRD patterns. All AM groups showed significantly greater surface roughness compared to the CON group (P < 0.001). ConclusionThe AM zirconia crowns showed bubbles and a rougher surface compared to the SM crowns. All groups exhibited typical zirconia traits and trueness levels within clinically acceptable limits, suggesting that current zirconia AM techniques could be suitable for dental applications.

Evaluation of Penetration Depth and Caries Progression using Resin Infiltrant in Natural White Spot Lesions of Primary Molars.

Management of white spot lesions (WSLs) using resin infiltrants, like ICON®, is a novel technique that emphasizes the concept of minimally invasive dentistry. Evaluate penetration depth and its effect on caries progression of ICON® in natural WSLs of primary molars. A total of 30 human primary molars with natural WSLs were selected. A total of 15 samples each were randomly selected to evaluate penetration depth and caries progression. To evaluate penetration depth, lesion surfaces were sectioned into two halves, wherein one half served as control, while the other half received ICON® infiltration treatment. To evaluate the effect on caries progression, samples were sectioned into two halves, wherein one half served as a control to its experimental counterpart, which received ICON® infiltration. The initial depth of the subsurface lesion (baseline data) was measured, and all the sample subsets underwent pH cycling. Confocal laser fluorescence microscope (CFLM) evaluation was performed, and penetration depth was assessed using a laser scanning microscopy (LSM) image reader, while caries progression was evaluated using PhotoScape® software. ICON® resin infiltrant penetrated to significant depths into the WSLs (p < 0.001) and demonstrated significant inhibition of caries progression (p < 0.001). The novel technique using ICON® could be an invaluable tool in the management of WSLs in primary teeth. Babu G, Mallikarjun S, Vijayan V, et al. Evaluation of Penetration Depth and Caries Progression using Resin Infiltrant in Natural White Spot Lesions of Primary Molars. Int J Clin Pediatr Dent 2024;17(4):390-394.

Microcirculatory visualization and metabolomics of Dalbergia cochinchinensis in ameliorating coronary microvascular dysfunction in rats

This study employed microcirculation visualization and metabolomics methods to explore the effect and possible mechanism of Dalbergia cochinchinensis in ameliorating coronary microvascular dysfunction(CMD) induced by microsphere embolization in rats. Sixty SPF-grade male SD rats were randomized into sham, model, and low-, medium-, and high-dose [1.5, 3.0, and 6.0 g·kg~(-1)·d~(-1), respectively] D. cochinchinensis water extract groups. The rats in sham and model groups were administrated with equal volume of normal saline by gavage once a day for 7 consecutive days. The rat model of CMD was prepared by injecting polyethylene microspheres into the left ventricle, while the sham group was injected with an equal amount of normal saline. A blood flow meter was used to measure blood flow, and a blood rheometer to measure blood viscosity and fibrinogen content. An automatic biochemical analyzer and reagent kits were used to measure the serum levels of myocardial enzymes, glucose, and nitric oxide(NO). Hematoxylin-eosin(HE) staining was used to observe the pathological changes of myocardial tissue. DiI C12/C18 perfusion was used to infuse coronary microvessels, and the structural and morphological changes were observed using a confocal laser scanning microscope. AngioTool was used to analyze the vascular area, density, radius, and mean E lacunarity in the microsphere embolization area, and vascular blood flow resistance was calculated based on Poiseuille's law. Non-targeted metabolomics based on high performance liquid chromatography-quadrupole-time-of-flight mass spectrometry(UPLC-Q-TOF-MS) was employed screen potential biomarkers and differential metabolites regulated by D. cochinchinensis and the involved metabolic pathways were enriched. The pharmacodynamic results showed that compared with the model group, D. cochinchinensis significantly increased mean blood flow, reduced plasma fibrinogen content, lowered the levels of myocardial enzymes such as creatine kinase(CK), creatine kinase-MB(CK-MB), and lactate dehydrogenase(LDH), alleviate myocardial injury, and protect damaged myocardium. In addition, D. cochinchinensis significantly increased serum NO content, promoted vascular smooth muscle relaxation, dilated blood vessels, lowered serum glucose(GLU) level, improved myocardial energy metabolism, and alleviated pathological changes in myocardial fibrosis and inflammatory cell infiltration. The results of coronary microcirculation perfusion showed that D. cochinchinensis improved the vascular morphology, increased the vascular area, density, and radius, reduced vascular mean E lacunarity and blood flow resistance, and alleviated vascular endothelial damage in CMD rats. The results of metabolomics identified 45 differential metabolites between sham and model groups, and D. cochinchinensis recovered the levels 25 differential metabolites, which were involved in 8 pathways including arachidonic acid metabolism, arginine biosynthesis, and sphingolipids metabolism. D. cochinchinensis can ameliorate coronary microcirculation dysfunction caused by microsphere embolization in rats, and it may alleviate the pathological changes of CMD rats by regulating inflammatory reaction, endothelial damage, and phospholipid metabolism.

An in vitro evaluation of Icon resin infiltrant penetration into demineralized enamel lesions using an indirect staining technique with confocal laser scanning microscope analysis in dual fluorescence mode.

White spot lesion is the first clinical sign of a caries lesion and represents mineral loss from the enamel subsurface. The aim of this study was to evaluate the penetration depth (PD) of Icon resin infiltrant into artificially demineralized enamel lesions using confocal laser scanning microscope (CLSM) analysis in dual fluorescence mode. The design of the study was an in vitro study. 22 extracted human permanent maxillary central incisor teeth were collected, and enamel sections were obtained from the coronal middle third. All enamel specimens were exposed to demineralization and remineralization solutions for 14 days. On positive confirmation of enamel demineralization by scanning electron microscope analysis, 20 specimens were then subjected to Icon resin infiltration following manufacturer instructions. Specimens were processed with indirect staining technique using rhodamine B and sodium fluorescein dyes and examined under CLSM at ×10 magnification in dual fluorescence mode using ImageJ software to evaluate PD of resin infiltrant into demineralized enamel lesions. Obtained data were analyzed using an independent t-test. P ≤0.05 was considered statistically significant. The maximum depth of demineralized enamel lesion was 590 μm, and the mean depth was 290.78 ± 14.80 μm. The maximum depth of resin infiltrant penetration was 580 μm, and the mean depth was 279.08 ± 13.88 μm; P = 0.006. The percentage penetration of resin infiltrant was 95.99%. Icon resin infiltrant was highly effective in its depth of penetration into demineralized enamel lesions. The use of indirect staining and CLSM analysis in dual fluorescence mode is more reliable and accurate technique to evaluate the PD of resin infiltrant.

Comparative Evaluation of Penetration of Various Nano-sized Intra-canal Medicaments: An In Vitro Confocal Laser Scanning Microscopic Study.

To assess and contrast the depth of penetration of conventional calcium hydroxide, nanoparticle calcium hydroxide, silver nanoparticles, and combination of nanoparticle calcium hydroxide and silver nanoparticles into dentinal tubules using confocal laser scanning microscope. Eighty human single-rooted teeth were decoronated and instrumented up to Protaper Universal F3. Teeth were separated into four groups at random (n = 20) following chemomechanical preparation. Group 1: Control Conventional Calcium Hydroxide; Group 2: Nanoparticle Calcium Hydroxide; group 3: Silver Nanoparticles; group 4: Combination of Nanoparticle Calcium Hydroxide and Silver Nanoparticles. With the use of lentulo spirals, medications were injected into the canals, stirred up with ultrasound, and then kept at 37°C for 24 hours. A 1 mm thick slice was obtained at 5 mm from the root apex by sectioning the root perpendicular to the long axis of the tooth and then put on a glass slide to measure the depth of penetration using a confocal laser microscope. To quantify the depth of penetration among the four groups, a one-way ANOVA was used and post hoc-Tukey's test was used to compare between groups. All of the groups were statistically significant, with group 4 showing the greatest depth of penetration, followed by group 2 and group 3. In contrast, all other groups in the intergroup comparison were statistically significant (P value 0.05) aside from the comparison of group 2 to group 3. Silver nanoparticles and nanoparticle calcium hydroxide together demonstrated greater penetration than calcium hydroxide, silver nanoparticles, and nanoparticle calcium hydroxide alone.

Assessment of different irrigation techniques on the penetration depth of different sealers into dentinal tubules by confocal laser scanning microscope: An in vitro comparative study.

The effective disinfection of the entire root canal system aids in the penetration of irrigants into the dentinal tubules further improving sealer penetration and achieving a three-dimensional seal in endodontically treated teeth. Various final irrigation techniques can be employed to achieve this goal. Therefore, this study intended to assess and compare the efficacy of three final irrigation techniques on the depth of penetration of two root canal sealers into dentinal tubules using confocal laser scanning microscope (CLSM). Forty-eight single-rooted mandibular premolars were selected and decoronated to a length of 12 mm. All the samples were prepared using ProTaper Gold rotary files and divided into three groups: Group 1 - Conventional syringe irrigation (CSI), Group 2 - passive ultrasonic irrigation (PUI), and Group 3 - Pro-agitator tip system (PATS). Each group was divided into two subgroups: Subgroup A - AH Plus and Subgroup B - GuttaFlow Bioseal (GFB). Then, sealers were mixed with 0.1% rhodamine B dye and the samples were obturated. All the samples were sectioned at 2 mm and 5 mm from the apex and visualized under confocal laser scanning microscope (CLSM) (10×) for maximum mean penetration depth and percentage of sealer penetration. Statistical analysis was done using the independent t-test and one-way analysis of variance test, followed by Tukey's Post hoc analysis. PUI performed better in the apical third, whereas PUI and PATS showed comparable results in the middle third for both depth and percentage of sealer penetration. Among the two sealers, GFB performed better than AH Plus in both the apical and middle third. These values were statistically significant. (P < 0.05). Final irrigation activation with PUI or PATS can significantly improve sealer penetration. The average depth of penetration of GFB both at the middle and apical third of the root was significantly superior to AH Plus.

Interactions Between Alumina Inclusions at the Liquid Iron/Argon Gas Interface: Role of Contact Line Undulation

A deep understanding of the behavior of nonmetallic inclusions is essential for steel cleanliness control. The behavior of alumina inclusions at the liquid iron/argon gas interface is investigated using a high‐temperature confocal scanning laser microscope. The obtained images are used to determine the moving velocity of the inclusions on the interface. The obtained experimental data are quantitatively evaluated using the lateral capillary interaction model for multipole orders established by Danov–Kralchevsky while taking into account the resistive drag force. The attraction forces calculated from these data are in the range between ≈10−13 and ≈10−11 N. The best‐fitting model is assigned for each case. The multipole models almost counterbalance the drag force, indicating a good interpretation of the interaction between the inclusions. Moreover, the acting length of this interaction is examined and compared to the previous work on Ce2O3 inclusions. It is found that alumina inclusions generally exhibit a larger acting length at a large critical radius and a smaller acting length at a small critical radius when comparing them to their counterpart cerium oxide inclusions. Considering the particle shapes, high shape irregularity is better interpreted by higher orders of the multipoles.

Endoplasmic Reticulum Stress Induces Vasodilation in Liver Vessels That Is Not Mediated by Unfolded Protein Response.

There is a growing body of evidence that ER stress and the unfolded protein response (UPR) play a key role in numerous diseases. Impaired liver perfusion and ER stress often accompany each other in liver diseases. However, the exact impact of ER stress and UPR on the hepatic perfusion is not fully understood. The aim of this study was to disclose the effect of ER stress and UPR on the size of liver vessels and on the levels of Ca2+ and nitric oxide (NO), critical regulators of vascular tonus. This study was carried out in precisely cut liver tissue slices. Confocal microscopy was used to create 3D images of vessels. NO levels were determined either using either laser scan microscopy (LSM) in cells or by NO-analyser in medium. Ca2+ levels were analysed by LSM. We show that tunicamycin, an inducer of ER stress, acts similarly with vasodilator acetylcholine. Both exert a similar effect on the NO and Ca2+ levels; both induce significant vasodilation. Notably, this vasodilative effect persisted despite individual inhibition of UPR pathways-ATF-6, PERK, and IRE1-despite confirming the activation of UPR. Experiments with HUVEC cells showed that elevated NO levels did not result from endothelial NO synthase (eNOS) activation. Our study suggests that tunicamycin-mediated ER stress induces liver vessel vasodilation in an NO-dependent manner, which is mediated by intracellular nitrodilator-activatable NO store (NANOS) in smooth muscle cells rather than by eNOS.

Physicochemical transformation of gasification slags with different residue carbon contents during sintering/melting process

The ash residue after gasification in the coal gasifier contains a certain proportion of residual carbon, which exerts a significant effect on the slag properties such as sintering, melting, and flow within the furnace. The residues discharged outside the gasifier retain the distribution patterns of ash and residual carbon under gasification conditions. This study selected coarse and fine residues generated from an entrained-flow gasifier and investigated the transformation of slags with different carbon contents during heating process. The obtained ash residues underwent characterization to determine the modes of the compositions occurrence. Subsequently, ash residues with different carbon contents were observed for the sintering-melting processes with a high-temperature confocal scanning laser microscope (CSLM). With the aid of FactSage, the physicochemical transformation of slag particles was determined. The impact of residual carbon on particle characteristics manifests in both physical structure and chemical reactions. On one hand, residue residual carbon can act as a skeleton during the melting process, causing the molten phase to enter the pores of porous carbon, intensifying particle shrinkage. After the inorganic components melt, the liquid encapsulated by carbon retains the original particle shape. On the other hand, the carbon can react with the inorganic ash components. If the carbon content is less than 6%, a new FexSi with a high ash melting point can be formed. As the carbon content increases, the carbon reacts with the Si to form SiC. This implies a reduction in the liquid content. Therefore, the flow temperature is greatly delayed by an increase in carbon content above 14%.

Biological control of the native endophytic fungus Pochonia chlamydosporia from the root nodule of Dolichos lablab on Fusarium wilt of banana TR4.

Fusarium wilt of banana caused by Fusarium oxysporum f. sp. cubense, Tropical Race 4 (TR4) is a soil-borne disease, and it is devastating. At present, the biological control using antagonistic microorganisms to mitigate TR4 is one of the best strategies as a safe and green way. Yunnan has abundant and diverse microbial resources. Using the dual-culture method, the antagonistic endophytic fungi against TR4 were isolated and screened from the root nodule of Dolichos lablab. The effect of the highest antagonistic activity strain on the morphology of the TR4 mycelium was observed using the scanning electron microscope. According to morphological characteristics and sequence analysis, the strain was identified. The biocontrol effect and plant growth promotion were investigated by greenhouse pot experiment. Using the confocal laser scanning microscope and the real-time fluorescence quantitative PCR, the dynamics of TR4 infestation and the TR4 content in banana plant roots and corms would also be detected. In this study, 18 native endophytic fungi were isolated from a root nodule sample of Dolichos lablab in the mulch for banana fields in Yuxi, Yunnan Province, China. The YNF2217 strain showed a high antagonistic activity against TR4 in plate confrontation experiments, and the inhibition rate of YNF2217 is 77.63%. After TR4 culture with YNF2217 for 7 days in plate confrontation experiments, the morphology of the TR4 mycelium appeared deformed and swollen when observed under a scanning electron microscope. According to morphological characteristics and sequence analysis, the strain YNF2217 was identified as Pochonia chlamydosporia. In the greenhouse pot experiment, the biocontrol effect of YNF2217 fermentation solution on TR4 was 70.97% and 96.87% on banana plant leaves and corms, respectively. Furthermore, YNF2217 significantly promoted the growth of banana plants, such as plant height, leaf length, leaf width, leaf number, pseudostem girth, and both the aboveground and underground fresh weight. Observations of TR4 infestation dynamics in banana roots and corms, along with real-time fluorescence quantitative PCR, verified that YNF2217 inoculation could significantly reduce the TR4 content. Therefore, YNF2217 as P. chlamydosporia, which was found first time in China and reported here, is expected to be an important new fungal resource for the green control of Fusarium wilt of banana in the future.

The Significance of Xylem Structure and Its Chemical Components in Certain Olive Tree Genotypes with Tolerance to Xylella fastidiosa Infection.

Olive quick decline syndrome (OQDS) is a devastating plant disease caused by the bacterium Xylella fastidiosa (Xf). Exploratory missions in the Salento area led to the identification of putatively Xf-resistant olive trees (putatively resistant plants, PRPs) which were pauci-symptomatic or asymptomatic infected plants belonging to different genetic clusters in orchards severely affected by OQDS. To investigate the defense strategies employed by these PRPs to contrast Xf infection, the PRPs were analyzed for the anatomy and histology of xylem vessels, patterns of Xf distribution in host tissues (by the fluorescent in situ hybridization technique-FISH) and the presence of secondary metabolites in stems. The xylem vessels of the PRPs have an average diameter significantly lower than that of susceptible plants for each annual tree ring studied. The histochemical staining of xylem vessels highlighted an increase in the lignin in the parenchyma cells of the medullary rays of the wood. The 3D images obtained from FISH-LSM (laser scanning microscope) revealed that, in the PRPs, Xf cells mostly appeared as individual cells or as small aggregates; in addition, these bacterial cells looked to be incorporated in the autofluorescence signal of gels and phenolic compounds regardless of hosts' genotypes. In fact, the metabolomic data from asymptomatic PRP stems showed a significant increase in compounds like salicylic acid, known as a signal molecule which mediates host responses upon pathogen infection, and luteolin, a naturally derived flavonoid compound with antibacterial properties and with well-known anti-biofilm effects. Findings indicate that the xylem vessel geometry together with structural and chemical defenses are among the mechanisms operating to control Xf infection and may represent a common resistance trait among different olive genotypes.

Characterization of Gold-Enhanced Titania: Boosting Cell Proliferation and Combating Bacterial Infestation.

In this study an approach was made to efficaciously synthesize gold enhanced titania nanorods by electrospinning. This study aims to address effects of gold enhanced titania nanorods on muscle precursor cells. Additionally, implant related microbial infections are prime cause of various disastrous diseases. So, there is predictable demand for synthesis of novel materials with multifunctional adaptability. Herein, gold nanoparticles were attached on titania nanorods and described using many sophisticated procedures such as XRD, SEM, EDX and TEM. Antimicrobial studies were probed against Gram-negative Escherichia coli. C2C12 cell lines were exposed to various doses of as-prepared gold enhanced titania nanorods in order to test in vitro cytotoxicity and proliferation. Cell sustainability was assessed through Cell Counting Kit-8 assay at regular intervals. A phase-contrast microscope was used to examine morphology of exposed C2C12 cells and confocal laser scanning microscope was used to quantify cell viability. The findings indicate that titania nanorods enhanced with gold exhibit superior antimicrobial efficacy compared to pure titania. Furthermore, newly synthesized gold-enhanced titania nanorods illustrate that cell viability follows a time and concentration dependent pattern. Consequently, our study provides optimistic findings indicating that titania nanorods adorned with gold hold significant potential as foundational resource for developing forthcoming antimicrobial materials, suitable for applications both in medical and biomedical fields. This work also demonstrates that in addition to being extremely biocompatible, titania nanorods with gold embellishments may be used in a range of tissue engineering applications in very near future.

Characterization of the microstructure evolution features of various aggregates based on confocal laser scanning microscope

To reveal the microscale structural evolution characteristics of aggregates, this study employs confocal laser scanning microscope (CLSM) to conduct the surface microstructures of six aggregates: limestone, basalt, granite, diabase, sandstone, and recycled aggregate (RA). Quantitative analysis was performed on the surface morphology, roughness parameters, and material ratio of the aggregates. The results indicate that the surface features of the aggregates vary with the type and treatment method, and these distinctions may be attributed to variations in diagenetic conditions. In the original state, the surface texture of limestone, basalt, and diabase is relatively minimal, with arithmetic mean height (Ra) distributed between 1.4 μm and 3.5 μm. Conversely, the surface texture of granite, sandstone, and RA is more complex, with Ra distributed between 7.5 μm and 9.5 μm. The roughness indices of basalt, limestone, and diabase show an increasing trend after lime treatment, indicating a more pronounced presence of microscopic peaks and pits. In contrast, all roughness indices of granite, sandstone, and RA exhibit a declining after lime treatment. After polishing, the Ra of the surfaces of the six different aggregates shows varying degrees of reduction. Specifically, Ra decreased by 43.89%, 33.11%, 26.52%, 30.14%, 29.80%, and 38.79% for limestone, basalt, granite, diabase, sandstone, and RA, respectively. Furthermore, the height distribution frequency and material ratio of aggregate surfaces vary with the type and treatment of aggregates. Through grey correlation analysis, the correlation degrees of root mean square slope (Rdq), kurtosis (Rku), and surface texture aspect ratio (Rtr) are 0.9524, 0.9522, and 0.9514, respectively, belonging to hybrid parameter, height parameter, and spatial parameter. This suggests a close relationship between these parameters and the polished stone value (PSV) of the aggregates. These findings offer valuable insights for improving aggregate selection and treatment processes, potentially leading to enhanced durability and performance of construction materials.