Large Amplification Research Articles

Numerical assessment of tidal potential energy in the Brazilian Equatorial Shelf

The Brazilian Equatorial Shelf (BES) is one among the macrotidal regions worldwide. This study used a high-resolution numerical configuration of the ocean model ROMS (Regional Ocean Modeling System) forced with realistic surface and lateral forcing, as well as with tides and river discharges. Tidal heights of more than 2 m were found in three regions in BES due to the large tidal amplification across the estuarine channels inside each region: Amazon, Pará, and Maranhão, and for a considerable time fraction. Heights between 4 and 5 m occurred with a frequency greater than 20%–30% in some regions. All hypothetical barrages proposed in this study were capable of an annual power production, in two-way mode, higher than La Rance (533 GWh year−1, two-way operation, France) and Sihwa (553 GWh year−1, flood-only operation, South Korea), except one with the same production as Sihwa barrage. The installation effort was evaluated using the Gibrat ratio, the ratio between the length of the barrage and its annual energy production. Among the proposed barrages, the most efficient ones have an annual power generation greater than 1500 GWh year−1 and a Gibrat ratios between 1.17 and 3.26, much lower than the Gibrat ratio of Sihwa tidal barrage.

FASTSync: A FAST Delta Sync Scheme for Encrypted Cloud Storage in High-bandwidth Network Environments

More and more data are stored in cloud storage, which brings two major challenges. First, the modified files in the cloud should be quickly synchronized to ensure data consistency, e.g., delta synchronization (sync) achieves efficient cloud sync by synchronizing only the updated part of the file. Second, the huge data in the cloud needs to be deduplicated and encrypted, e.g., Message-Locked Encryption (MLE) implements data deduplication by encrypting the content among different users. However, when combined, a few updates in the content can cause large sync traffic amplification for both keys and ciphertext in the MLE-based cloud storage, significantly degrading the cloud sync efficiency. A feature-based encryption sync scheme, FeatureSync, is proposed to address the delta amplification problem. However, with further improvement of the network bandwidth, the performance of FeatureSync stagnates. In our preliminary experimental evaluations, we find that the bottleneck of the computational overhead in the high-bandwidth network environments is the main bottleneck in FeatureSync. In this article, we propose an enhanced feature-based encryption sync scheme FASTSync to optimize the performance of FeatureSync in high-bandwidth network environments. The performance evaluations on a lightweight prototype implementation of FASTSync show that FASTSync reduces the cloud sync time by 70.3% and the encryption time by 37.3%, on average, compared with FeatureSync.

Nonlinear Equalization for Performance Enhancement of FBMC Systems Using Walsh Transform

The Filter Bank Multi-Carrier (FBMC) is an interesting recent technology for next-generation wireless radio communication systems. Equalization is a fundamental technique for enhancing Bit Error Rate (BER) performance. The traditional Linear Zero Forcing (LZF) and Linear Minimum Mean Square Error (LMMSE) equalizers have large noise amplification and high complexity, respectively. As the estimated error of the Signal-to-Noise Ratio (SNR) grows, the BER performance of the LMMSE equalizer degrades. In this paper, we present a Joint Low Complexity Optimized ZF-Successive Interference Cancellation (JLCOZF-SIC) equalizer for FBMC communication systems that are based on the Walsh–Hadamard Transform (WHT) rather than the Fast Fourier Transform (FFT). As in the MMSE-Successive Interference Cancellation (MMSE-SIC) equalizer, the proposed equalizer avoids the estimating error induced by average power per symbol estimation. The simulation results show that the proposed algorithm improves the system performance more than the existing algorithms. Furthermore, the proposed equalization provides stability in the BER performance at high levels of the co-Carrier Frequency Offset (co-CFO). In terms of computational complexity, the proposed scheme has a lower computational complexity than traditional schemes.

Establishing the Link between X-Chromosome Aberrations and TP53 Status, with Breast Cancer Patient Outcomes.

Ubiquitous to normal female human somatic cells, X-chromosome inactivation (XCI) tightly regulates the transcriptional silencing of a single X chromosome from each pair. Some genes escape XCI, including crucial tumour suppressors. Cancer susceptibility can be influenced by the variability in the genes that escape XCI. The mechanisms of XCI dysregulation remain poorly understood in complex diseases, including cancer. Using publicly available breast cancer next-generation sequencing data, we show that the status of the major tumour suppressor TP53 from Chromosome 17 is highly associated with the genomic integrity of the inactive X (Xi) and the active X (Xa) chromosomes. Our quantification of XCI and XCI escape demonstrates that aberrant XCI is linked to poor survival. We derived prognostic gene expression signatures associated with either large deletions of Xi; large amplifications of Xa; or abnormal X-methylation. Our findings expose a novel insight into female cancer risks, beyond those associated with the standard molecular subtypes.

Supercapacitors with Gold Colloids That Are Placed at a Short Distance from Active-Carbon Electrodes; The Case for a Plasmonic Effect at the Electrolyte/Electrode Interface

Supercapacitors (S-C) are fast charge/discharge elements. These short-term energy storage found many applications; among which are, powering electronic devices, boosters of fast charging batteries and possibly, as buffers between highly fluctuating sustainable sources and the rather stable electrical grid. For double-layer S-C, one takes advantage of the very narrow interface between an electrolyte and a conductive porous electrode. In contrast, ordinary capacitors are made of a relatively thicker dielectric material, sandwiched between two electrodes.In the past, polarity increase in capacitors was achieved by dispersing conductive colloids in the entire volume of the dielectric material. This approach was primarily used for microwave and optical devices – a field known as plasmonics. For S-C it means that the conductive colloids should be dispersed within the double-layer region, or fairly close to it. The impact of such an approach on the low frequency supercapacitors is not fully yet known. In order to maintain a full polarization effect (as opposed to simply increasing the electrode conductivity), we kept the AuNP at a short distance from the electrode. This is achieved by coating the colloids with a negatively charged ligand - the same approach used to keep a colloidal suspension intact.Here we explore the addition of nano-size Au particles (AuNP) to active-carbon electrodes to find a large amplification in the specific capacitance. For example, C-V data at a scan rate of 20 mV/s indicated a specific capacitance amplification of more than 10 (!) (with respect to a reference sample without the colloids) when 30 micro-g of AuNPs were incorporated with 200 milli-g of active carbon while using a 1 M Na2SO4 electrolyte and a 5% cellulose acetate butyrate binder. These experiments were corroborated by simulations: the Au colloids are indeed to be placed at close proximity but not in contact with the electrodes.

Multi-scale Simulation of Subsequent Tsunami Waves in Japan Excited by Air Pressure Waves Due to the 2022 Tonga Volcanic Eruption

The 2022 Hunga Tonga-Hunga Ha’apai eruption generated tsunamis that propagated across the Pacific Ocean. Along the coast of Japan, nearshore amplification led to amplitudes of nearly 1 m at some locations, with varying peak tsunami occurrence times. The leading tsunami wave can generally be reproduced by Lamb waves, which are a type of air-pressure wave generated by an eruption. However, subsequent tsunamis that occurred several hours after the leading wave tended to be larger for unknown reasons. This study performs multi-scale numerical simulations to investigate subsequent tsunami waves in the vicinity of Japan induced by air pressure waves caused by the eruption. The atmospheric pressure field was created using a dispersion relation of atmospheric gravity wave and tuned by physical parameters based on observational records. The tsunami simulations used the adaptive mesh refinement method, incorporating detailed bathymetry and topography to solve the tsunami at various spatial scales. The simulations effectively reproduced the tsunami waveforms observed at numerous coastal locations, and results indicate that the factors contributing to the maximum tsunami amplitude differ by region. In particular, bay resonance plays a major role in determining the maximum amplitude at many sites along the east coast of Japan. However, large tsunami amplification at some west coast locations was not replicated, probably because it was caused by amplification during oceanic wave propagation rather than meteorological factors. These findings enhance our understanding of meteotsunami complexity and help distinguish tsunami amplification factors.

Large amplification of the sensitivity of symmetric-response magnetic tunnel junctions with a high gain flux concentrator

Miniaturized, ultra-sensitive and easily integrable magnetometers are needed for many applications like space exploration or medical survey. In this study, we combine innovative magnetic tunnel junctions having a symmetric resistance-field (R–H) response with a high gain flux concentrator. In our junctions, the magnetization of the free layer (FL) is stabilized in an anti-parallel configuration with respect to that of the reference layer. This configuration is achieved by using a soft exchange pinning of the FL. We precisely adjust the exchange field value with a dusting layer of ruthenium used to weakly decouple the magnetization of the FL from the local moments of the antiferromagnet. In order to improve the junction's sensitivity, we study the influence of the exchange field value and of the shape anisotropy on the even-function R–H response. In particular, we compare circular junctions with elliptic or rectangular junctions of various aspect ratios and orientations. We find that the sensitivity of the junctions increases when reducing the soft-pinning exchange field and by using junctions with an elongated shape in the direction of the applied field. Finally, we were able to further increase the sensitivity by a factor 440 due to a flux concentrator placed around the junction by electrochemical deposition of NiFe. Its design is optimized (elongated shape, 5–7 μm thickness and 10 μm air-gap) in order to obtain this very high gain. The complete sensor system composed of these magnetic tunnel junctions and the flux concentrator allows to reach sensitivities larger than 1000%/mT.

Influence of Positioning of Shear Wall on the Torsional Response of Building

Abstract: It would be ideal if all buildings have their lateral-load resisting elements symmetrically arranged and earthquake ground motions would strike in known directions. Due to scarcity of land in big cities, architects often propose irregular buildings in order to utilize maximum available land area and to provide adequate ventilation and light in various building components. However, it is quite often that structural irregularity is the result of a combination of both types. Most buildings have some degree of irregularity in the geometric configuration or the distribution of mass, stiffness, and/or strength. Due to one or more of these asymmetries, thestructure’s lateral resistance to the ground motion is usually torsionally unbalanced creating large displacement amplifications and high force concentrations within the resisting elements which can cause severe damages and at times collapse of the structure. Eccentric arrangement of non-structural components, asymmetric yielding, presence of rotational component in ground motions and the variations in the input energy imparted by the ground motions also contribute significantly to the torsional response of buildings. So, this research work demonstrates the importance oflocation of shear wall is should be checked before the sequential failure defined by the Response spectrum analysis method. In Numerical Tool like SAP-2000 which are uses worldwide for pushover analysis method.

Design and analysis of a compliant microgripper with a large amplification ratio

Design and analysis of a compliant microgripper with a large amplification ratio

Towards a finite-time singularity of the Navier–Stokes equations. Part 3. Maximal vorticity amplification

An exact analytical solution is obtained for the dynamical system derived in Part 1 of this series (Moffatt & Kimura, J. Fluid Mech, vol. 861, 2019a, pp. 930–967), which describes the approach of two initially circular vortices of finite but small cross-section symmetrically located on inclined planes. This exact solution, applicable in the inviscid limit, allows determination of the amplification $\mathcal {A}_{\omega }$ of the axial vorticity within the finite time $T$ during which the basic assumptions of the model continue to apply. It is first shown that, for arbitrarily prescribed $\mathcal {A}_{\omega }$ , it is possible to specify smooth initial conditions of finite energy such that, in the inviscid limit, this amplification is achieved within the time $T$ . When viscosity is included, an estimate is provided for the minimum vortex Reynolds number that is sufficient for the same result to hold. The predictions are broadly compatible with results from direct numerical simulations at moderate Reynolds numbers. Moreover, it is shown that one may come arbitrarily close to a finite-time singularity of the Navier–Stokes equation by appropriate choice of an initial, smooth, finite-energy velocity field; however, this approach to a singularity is ultimately thwarted through breach of the assumptions on which the dynamical system is based. Thus we make no claim here concerning realisation of a Navier–Stokes singularity. Moreover, we find that the conditions required to attain a large amplification $\mathcal {A}_{\omega }\gg 1$ during the time $T$ are far beyond those that can be realised in either experiment or direct numerical simulation.

Schrödinger equation driven by the square of a Gaussian field: instanton analysis in the large amplification limit

We study the tail of p(U), the probability distribution of , for , being the solution to , where is a complex Gaussian random field, z and x respectively are the axial and transverse coordinates, with , and both and g > 0 are real parameters. We perform the first instanton analysis of the corresponding Martin-Siggia-Rose action, from which it is found that the realizations of S concentrate onto long filamentary instantons, as . The tail of p(U) is deduced from the statistics of the instantons. The value of g above which diverges coincides with the one obtained by the completely different approach developed in Mounaix et al (2006 Commun. Math. Phys. 264 741). Numerical simulations clearly show a statistical bias of S towards the instanton for the largest sampled values of . The high maxima—or ‘hot spots’—of for the biased realizations of S tend to cluster in the instanton region.

Dynamic Amplification Factors of an Arch Bridge Under Random Traffic Flows

Among large-span bridges, arch bridges have relatively high stiffness, which may lead to large dynamic amplification factors (DAFs). The DAFs suggested by current codes mostly originate from common simply supported beam bridges. Previous DAF studies on dynamic vehicle–bridge solutions for arch bridges have mainly focused on one or two side-by-side vehicles. However, complex traffic flows with randomness rather than one or two vehicles act on bridges. DAFs that consider the effects of random traffic flows have not previously been reported. In this study, a random traffic–bridge vibration solution was established to explore the DAFs of arch bridge components. The randomness of the traffic parameters and road roughness was explored. The randomness of the external excitation, including traffic flow and road roughness, resulted in random dynamic responses and DAFs of the arch bridge components. Normal distributions could be used to fit the DAF distributions of each arch bridge component under random vehicle spacing, weight, speed, and road roughness. Under random traffic parameters, the coefficients of variation of the DAFs exceeded the 5% accepted level. The shortest suspenders were more sensitive to the randomness of the traffic flow parameters. Both the mean and coefficient of variation of the DAFs increased with worsening of the road conditions. The influence of the randomness of the road roughness on the DAFs of arch bridges must be considered, particularly for the shortest suspender. The 95% upper confidence limits of the DAFs for all components may be greater than the suggested values in the code.

A Review Paper on Influence of Positioning of Shear Wall on the Torsional Response of Building

Abstract: It would be ideal if all buildings have their lateral-load resisting elements symmetrically arranged and earthquake ground motions would strike in known directions. Due to scarcity of land in big cities, architects often propose irregular buildings in order to utilize maximum available land area and to provide adequate ventilation and light in various building components. However, it is quite often that structural irregularity is the result of a combination of both types. Most buildings have some degree of irregularity in the geometric configuration or the distribution of mass, stiffness, and/or strength. Due to one or more of these asymmetries, the structure’s lateral resistance to the ground motion is usually torsionally unbalanced creating large displacement amplifications and high force concentrations within the resisting elements which can cause severe damages and at times collapse of the structure. Eccentric arrangement of non-structural components, asymmetric yielding, presence of rotational component in ground motions and the variations in the input energy imparted by the ground motions also contribute significantly to the torsional response of buildings. So, this research work demonstrates the importance oflocation of shear wall is should be checked before the sequential failure defined by the Response spectrum analysis method. In Numerical Tool like SAP-2000 which are uses worldwide for pushover analysis method.

Large regenerative parametric amplification on chip at ultra-low pump powers

Chip-based optical amplifiers can significantly expand the functionalities of photonic devices. In particular, optical-parametric amplifiers (OPAs), with engineerable gain spectra, are well suited for nonlinear-photonic applications. Chip-based OPAs typically require long waveguides that occupy a large footprint, and high pump powers that cannot be easily produced with chip-scale lasers. We theoretically and experimentally demonstrate a microresonator-assisted regenerative OPA that benefits from the large nonlinearity enhancement of microresonators and yields a high gain in a small footprint. We achieve 30-dB parametric gain with only 9 mW of cw pump power and show that the gain spectrum can be engineered to cover telecom channels inaccessible with Er-based amplifiers. We further demonstrate the amplification of Kerr-soliton comb lines and the preservation of their phase properties. Additionally, we demonstrate amplification by injection locking of optical parametric oscillators (OPOs), which corresponds to a regenerative amplifier pumped above the oscillation threshold. Dispersion engineering techniques such as coupled cavities and higher-order-dispersion phase matching can further extend the tunability and spectral coverage of our amplification schemes. The combination of high gain, small footprint, low pump power, and flexible gain-spectrum engineering of our regenerative OPA is ideal for amplifying signals from the nanowatt to microwatt regimes for portable or space-based devices where ultralow electrical power levels are required and can lead to important applications in on-chip optical-, and microwave-frequency synthesis and precise timekeeping.

Modeling optical amplification in Er/Yb-codoped integrated Bragg gratings

Bragg gratings inscribed in active waveguides combine very efficient reflective properties with the amplifying capability of rare-earths, which may lead to large amplification and lasing performance. However, the response of these photonic structures highly depends on the grating parameters and working conditions, so modeling their behavior and dependences becomes fundamental. In this work, a numerical method has been implemented to simulate the optical power propagation along an Er/Yb-codoped integrated waveguide Bragg grating as a function of its most relevant operational parameters. The results obtained show the optimal conditions to maximize its performance as a highly amplifying reflector, but also its capability as a monolithic laser. In addition, the modeling results adequately match experimental values measured in fs-laser written structures in Er/Yb-codoped phosphate glass, supporting the accuracy of the numerical method developed and its usefulness for further optimizing these promising photonic structures.

Dynamic amplification of multi-span simply-supported prestressed concrete girder viaducts subjected to multi-body heavy vehicles

High productivity freight vehicles (HPFVs) are used in many countries to address increasing freight demand. However, it is then necessary to assess the safety of existing bridge structures subjected to HPFVs because of their increasing mass and dimension. A critical part of this work is to assess the dynamic amplification of such vehicles, without undue conservatism, often based on vehicle–bridge interaction (VBI) modelling. In the VBI problem, the vehicle model is usually derived using the Principle of Virtual Work or Euler–Lagrange methods. However, HPFVs are characterized by multiple bodies and articulation points and these techniques quickly become intractable. Alongside the vehicle model, the bridge is often assumed to be a single simply-supported span, or a few continuous spans, whereas many urban bridge viaducts, in particular, have multiple prestressed concrete (PSC) girder simply-supported spans. Furthermore, these bridges typically have an upwards hog as a result of the prestress and it is hypothesized that certain combinations of vehicle, hog, span length, and number of spans, could produce a large dynamic amplification of static load effects. In this work, Kane’s Method is applied to heavy vehicle with multi-trailers combinations which provides a relatively easy, systematic, and numerical manipulation means of determining the vehicle dynamic equations. The 9-axle B-Double vehicle, common in Australia, is used as an example to illustrate the procedure of deriving the vehicle dynamic equations. We apply the resulting vehicle models in a comprehensive VBI model to consider the dynamic amplification of PSC girder viaducts. The results indicate that the studied PSC girder viaducts experience higher amplification than the equivalent single-span simply-supported bridges. Recommendations for future studies and practice, such as the number of spans in the viaduct to obtain the ‘convergence’ of dynamic amplification, are given.

Assessment of Site Amplification Factors in Southern Lima, Peru Based on Microtremor H/V Spectral Ratios and Deep Neural Network

Evaluation of site amplification factors (SAFs) of seismic waves has been one of the important issues for evaluating seismic hazards. The authors have proposed a deep neural network (DNN) model in order to cost-effectively and accurately estimate SAF from microtremor horizontal-to-vertical spectral ratio (MHVR). In this study, we assessed the SAFs in southern Lima, Peru by estimating from MHVRs and DNN. First, we validated the applicability of the DNN model to Lima by estimating the SAFs from the MHVRs observed at seismic stations in Lima. From the comparison with the observed SAFs derived from spectral inversion technique, we confirmed that the SAFs in Lima were accurately estimated by the DNN model. The SAFs in the southern Lima including Chorrillos and Villa El Salvador districts were evaluated by applying the DNN model to the observed MHVRs at approximately 250 sites. We found that large amplifications at low frequency around 1 Hz were expected in the southeastern coastal areas formed by eolian sands whereas smaller amplification were estimated in the northwestern areas mainly located on alluvial deposits.

Nonlinear interaction of two non-uniform vortex sheets and large vorticity amplification in Richtmyer–Meshkov instability

Vortex dynamics is an important research subject for geophysics, astrophysics, engineering, and plasma physics. Regarding vortex interactions, only limited problems, such as point vortex interactions, have been studied. Here, the nonlinear interaction of two non-uniform vortex sheets with density stratification is investigated using the vortex sheet model. These non-uniform vortex sheets appear, for example, in the Richtmyer–Meshkov instability that occurs when a shock wave crosses a layer with two corrugated interfaces. When a strong vortex sheet approaches a weaker vortex sheet with opposite-signed vorticity, a locally peaked secondary vorticity is induced on the latter sheet. This emerging secondary vorticity results in a remarkable vorticity amplification on the stronger sheet, and a strong vortex core is formed involving the weak vortex sheet. The amplified vortices with opposite signs on the two vortex sheets form pseudo-vortex pairs, which cause an intense rolling-up of the two sheets. We also investigated the dependence of distance and initial phase difference of vorticity perturbations between two vortex sheets on the vorticity amplification and vortex sheet dynamics.

Large parametric amplification in kinetic inductance dominant resonators based on 3 nm-thick epitaxial superconductors

Ultra-thin superconducting aluminum films of 3-nm grown on sapphire by molecule-beam epitaxy show excellent superconductivity and large kinetic inductance. This results in a record high Kerr non-linearity of 33 kHz and 3.62 MHz per photon in notch-type and transmission-type resonators, respectively. 4-wave mixing leverages this non-linearity to achieve 12 dB parametric amplification in transmission type resonator, making the ultra-thin film ideal for photon detection and amplification applications.

Quantitative analysis of surface‐wave propagation in the Mexico City Valley

AbstractThe Mexico City basin is an extreme example of an alluvial geological structure that induces long duration and large amplification on ground motions. Researchers have established that the seismic wavefield within the Mexico City basin is composed primarily of surface waves. In the present work, we present a quantitative analysis of the surface‐wave field propagating in the Mexico City basin and generated by thrust‐ and normal‐faulting events. Surface waves are identified and extracted from three‐component ground motion recordings using a technique that exploits the polarization of ground motion. The spatial analysis of the extracted waves clearly shows that the basin response, is strongly dominated by low‐frequency ( to ) Love waves. For all seismic events considered, we found that the identified Love waves can reach amplitudes three times larger as compared to Rayleigh waves. Our analysis indicates that surface wave amplification (as defined in the present work) increases with the 1D fundamental resonant site‐period T1, and appears to be independent of earthquake magnitude. We also quantify the mean delay time of the central frequency f0 of the extracted waves. We found that the of Love waves is spatially more coherent as compared to that of Rayleigh waves. The parameter T1 appears to be a good “proxy” of surface wave effects. This is manifested by a reciprocal relation that was established between T1 and the frequency f0 of the extracted Love waves. Equally important, the latter reciprocal relation turns out to be independent of earthquake magnitude.