Kinds Of Wood Research Articles

Characteristics of Fast-Growing Wood Impregnated Using Monoethylene Glycol and SiO Nanoparticles Against Fungal Attacks

Jabon (Anthocephalus cadamba) and Sengon (Falcataria moluccana) were fast-growing wood species widely planted in the community forest. Both kinds of wood have low durability even though they can potentially be used in the carpentry material industry. Therefore, this research aimed to analyze the vacuum-pressure impregnation effect using monoethylene glycol (C2H6O2) or MEG and silica dioxide (SiO2) nanoparticles on wood resistance to fungal decay. The results showed that impregnation treatment with MEG and SiO2 nanoparticles significantly improved the durability of Jabon and Sengon against fungal attacks. Furthermore, MEGSiO2 with 24-hour polymerization had a better impact on durability compared to both the control and MEGSiO2 with 12-hour polymerization. The 24-hour polymerization using 1% SiO2 nanoparticles resulted in the lowest weight loss for Jabon (5.86% ) and Sengon (5.21%). In addition, the variation of SiO2 nanoparticle concentration did not significantly affect the weight loss and durability of Jabon and Sengon against fungal decay.

Enhanced solar interfacial evaporation through lignin-polyaniline composite coatings on Balsa wood substrates

Solar interfacial evaporation employing wood-derived substrates is increasingly acknowledged as a viable desalination and wastewater treatment technique. This study presents an optimized method that enhances the efficiency of solar interfacial evaporation by applying a coating of lignin-polyaniline composites (EHL-PANI) onto balsa wood substrates. Initial assessments involved comparing evaporators made from various kinds of wood, identifying balsa wood-based photothermal evaporators as the most effective, with an evaporation rate of 1.63 kg·m−2·h−1 and an efficiency of 72.7 %. Photothermal properties were further improved through the chemical oxidation of enzymatic hydrolysis lignin (EHL) with polyaniline, producing a composite with notably high dispersion stability and uniform particle distribution. This modification resulted in reduced particle size and enhanced stability of the polyaniline, which is crucial for boosting photothermal activity. Additionally, the EHL-PANI composites demonstrated exceptional light absorption, exceeding 95 %, and significant photothermal conversion efficiency across a broad wavelength range, attributable to polyaniline's broadband light absorption characteristics. A prototype evaporator, featuring the EHL-PANI coated on a balsa wood substrate, was constructed to assess performance, achieving a water evaporation rate of 2.10 kg·m−2·h−1 and an efficiency of 80.7 % under solar illumination of 1 kW·m−2.

Coumarins in Spirit Beverages: Sources, Quantification, and Their Involvement in Quality, Authenticity and Food Safety

This comprehensive review is devoted to an under-exploited family of phenolic compounds, the coumarins, and the most relevant strands in which they are involved in some spirit beverages—wine spirit, brandy, whiskey, sugar-cane spirits (rum and cachaça) and grape marc spirit—with great importance worldwide in terms of production, trade and consumption. It gathers the key discoveries on the topic, considering the production process of each spirit beverage, and the related sources of coumarins (different kinds of wood used in the ageing stage), along with the factors that govern them and can influence the sensory properties of the aged beverages. An overview of the analytical methods available for their identification/quantification is also included, as well as the corresponding trends for the advancement of knowledge in this field. Moreover, the remarkable role of coumarins as nutraceuticals, their importance as chemical markers for authenticity purposes, and their relationship with the food safety of these spirit beverages are also addressed, highlighting the current gaps and issues, and providing clues for future research.

Comparison of physico-chemical and thermo-mechanical properties of sungkai (Peronema canescens Jack.), sengon (Falcataria moluccana (Miq.) Barneby & J.W. Grimes), and teak (Tectona grandis L.f.) wood veneers

ABSTRACT Sungkai (Peronema canescens Jack.), sengon (Falcataria moluccana (Miq.) Barneby & J.W. Grimes), and teak (Tectona grandis L.f.) are some of the main fast-growing species in Indonesia. Limited research data on the physicochemical and thermo-mechanical properties of these wood species represents a significant drawback for their enhanced industrial utilization. This study aimed to evaluate the properties of these three kinds of wood according to their colour by applying the CIELab colour measuring system, chemical composition by Fourier-transform Infrared Spectroscopy (FTIR), and Pyrolysis–gas Chromatography–Mass Spectrometry (Py-GC/MS) analyses, and the thermo-mechanical properties by Thermogravimetric Analysis (TGA) and Dynamic Mechanical Analysis (DMA). The higher colour quantification (E*) value indicated brighter wood having higher carbohydrate and lower lignin content according to Py-GC/MS results. Besides, the colour may be attributed to the higher phenolic and extractive content. The order of woods from the highest to the lowest phenolic content was teak > sengon > sungkai. Meanwhile, DMA analysis revealed that sungkai had the highest storage modulus, followed by teak and sengon. The findings of this study suggested that the properties of wood could be predicted based on its colour appearance, which could be used in industrial applications for rapid identification of wood properties.

Evaluation of Effective Composite Biosorbents Based on Wood Sawdust and Natural Clay for Heavy Metals Removal from Water.

Bentonitic clay and wood sawdust are natural materials widely available in nature at low cost with high heavy metals sorption properties that, in this work, were combined to achieve an effective composite biosorbent with high sorption properties and enhanced mechanical stability. Pine, aspen, and birch wood sawdust, as well as different bentonite clays and different sawdust modification methods (H3PO4 or HCl) were used for preparing new composite biosorbents. A mixture of wood sawdust and bentonite in a ratio of 2:1 was used. All materials were characterized by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM) methods and tested for Cu and Ni ions removal from water. The adsorption process for all composite biosorbents was well described from a pseudo-second order kinetic model (R2 > 0.9999) with a very high initial adsorption rate of Cu and Ni ions and a maximum uptake recorded within 2 h. The results have shown that the adsorption capacity depends mainly on the kind of wood and the acid treatment of the wood that enhances the adsorption capacity. At a concentration of 50 mg/L, the biosorbent prepared using birch wood sawdust showed the worst performance, removing barely 30% of Cu and Ni ions, while aspen wood sawdust improved the adsorption of Cu (88.6%) and Ni (52.4%) ions. Finally, composite biosorbent with pine wood sawdust showed the best adsorption be haviour with an efficiency removal of 98.2 and 96.3% of Cu and Ni ions, respectively, making it a good candidate as an inexpensive and effective biosorbent for the removal of heavy metals.

Effects of volatile organic compounds of smoke from different woods on the heterocyclic amine formation and quality changes in pork patty

This study investigated the effects of smoke derived from cypress (CY), mulberry (MU), metasequoia (ME), pine (PI), and camphor (CA) on the heterocyclic aromatic amines (HAs), flavor, and sensory attributes of smoked pork patty. The results showed that the smoke derived from the five kinds of wood and the flavor of the corresponding smoked meat were classified into three types. Moreover, the smoke of CY and PI, and the smoke of MU and ME can be classified into one category respectively, which significantly improved the flavor of the smoked meat. Both free and protein-bound HAs were detected in smoked meat, while the smoking process significantly increased the HAs content, especially free Norharman (3.26 ng/g in control meat, and 82.24 ng/g in meat smoked with CY). Correlation analysis showed that various volatile organic compounds (VOCs) and HAs were closely associated. Future research should pay attention to the VOCs in smoked meat including vanillin, Close attention should be paid to tridecane and crotonic acid, as well as tetradecane and α-Dehydro-ar-himachalene in smoke, which were consistently correlated with various HAs and may participate in HAs formation. These results may reveal how the smoking process influences the formation of HAs and which factors should be targeted to inhibit HAs in smoked meat products.

STRUKTUR ANATOMI KAYU YANG DIPERDAGANGKAN DI KABUPATEN ACEH BESAR

This study aims to determine the anatomical structure of wood and its possiblity uses for trade in Aceh Besar District. The research was carried out by observing 13 wood samples from the Bogorience 1915 xylarium wood collection. The observed samples included macroscopic and microscopic characteristics. Macroscopic characteristics include texture, color, pattern, texture, and grain direction of the wood. Microscopic characteristics observed were growth circumference boundaries, vessels, pores, dots, and radii based on the International Association of Wood Anatomists (IAWA) book. Each preparation was observed using a microscope and analyzed descriptively. The results showed that the anatomical structures of the macroscopic and microscopic properties of the 13 Aceh Besar wood species varied in terms of texture, grain direction, radius size, crystal type, fiber length, vessel length, and fiber wall thickness. While the pattern, color, distribution of pores, type of dots, type of perforation area, type of parenchyma cells, and the composition of the cells composing the radius show uniformity, and two kinds of wood have prismatic crystals, namely Surian wood in upright cells and Bangkirai wood in straight cells lie down. The 13 types of wood, 46% include strong class I-II for construction, bridges, pillars, and floors. Meanwhile, 54% is classified as strong class III-V as a material for making furniture, doors, windows, and products that do not require heavy strength.

Effects of Shooting Angles and Ricochet Angles on Bullet Weight Upon Impact on Three Types of Woods (Balau, Resak, and Seraya)

This study aims to determine if the number of shots fired, bullet striation marks, and shooting and ricochet angles could influence bullet weight on three types of woods: Balau, Resak, and Seraya. The weapon and ammunition used in this study were CZ 75 SP-01 Shadow semi-automatic pistol with 9 mm full metal jacketed bullets (7.45 g). A total of 432 shots were fired, and only 114 bullets produced a ricochet effect. The result of objective one showed no significant relationship between the number of shots and the number of bullet striations for all three kinds of wood. Correlation-Regression analysis for the second objective showed a significant relationship between shooting angle and bullet weight when shooting on Balau (p < 0.01, R² = 0.065) and Seraya (p < 0.01, R² = 0.199) but not on Resak. The shooting angle influenced the bullet weight by 6.5 % to 20 % when shooting on Balau and Seraya. Both kinds of wood are closely related and share fibre composition and modulus of elasticity (MOE) characteristics. The result of the third objective showed a relationship between ricochet angle and bullet weight during the shooting on Resak (p < 0.01, R² = 0.142) but not on Balau and Seraya. The ricochet angle on Resak influenced the bullet weight by 14.2 + 9.8 %. It is probably due to Resak having the highest MOE among the three types of woods. This study concludes that bullet weight loss is due to the ricochet effect and the composition of the bullet’s target.

Influence of insect damage to the fatigue life of an old larch wood

In many cultural heritage buildings, structural members are made of wood. Over the years, wood is exposed to various biotic and abiotic degradation factors, including moisture oscillations, mechanical stress, and insect and fungal decay. In the present respective study, an experimental study on the fatigue life of 350 years old larch wood was carried out. The fatigue life of the old wood was compared to the fatigue life of the recent larch wood. A statistical model for the fatigue-life curves and their scatter was built for both kinds of wood. The model can consider different factors to the fatigue life, e.g. wood density, specimen orientation during loading, and extent of insect damage. An equivalent number of load cycles to failure was also defined, enabling a direct comparison of the fatigue life data for specimens with different wood densities or orientations during loading. From the results, it can be concluded that the proposed statistical model adequately describes the fatigue behaviour of both the old, insect-damaged wood and the recent larch wood.

Effects of wood texture and color on aesthetic pleasure: two experimental studies

The texture and color on wood are key factors that influence an individual's perception of it. However, little research has been done to confirm what kind of pattern in textures and colors are more likely to evoke individual aesthetic pleasure. Therefore, twenty-four decorative wood from northern China were selected, identified, and quantified in their colors with a CR-5 Colorimeter. We picked out eight kinds of wood with optimal texture characteristics through feature-fusion wood grain recognition (FWGR) and enhanced the texture features with photoshop in VR space. The result show that, in the color dimension, woods in the hue range of 20-25 and saturation of 65-75 were considered beautiful for individual perception of aesthetic. In the texture dimension, the size of the space affects the individual's preference for texture. When the pattern of the wood ray is continuous and clear, the individual's perception of its fluidity is enhanced; while for the fuzzy and interrupted pattern of the wood ray, the individual does not follow the fluidity of the line but focuses on the overall uniformity.

Brief Introduction to Properties of Wood and Application of Wood in Architectural Structures

Wood’s existence in earth is much earlier than human beings’ appearance, after thousands of years’ evolution, many kinds of wood are strong enough to support humans’ basic needs. Since the mid-20th century, scientists had made a great progress in chemistry and civil engineering, which made types of materials for architecture become abundant. However, despite of all the advantages that wood has got, the inflammability and mildew are the main reasons that wood cannot be largely used in the super high-rise building or huge building. The passage mainly introduced the excellent architectural properties of wood with detailed data, wood-based structure along with its characteristics and the typical wooden structures worldwide. From the current situation, wood is widely used in the medium and small-scale building for its good properties and well performance on many respects, including the ancient masterpieces. The typical and contemporary wood building structures system have shown the ingenious ideas and connotation within the structure. Furthermore, modified materials based on wood are developed to adapt the higher standards and requirements for architecture. In this way wood shall overcome the disadvantages of inflammability and mildew and other flaws due to congenital defects and acquired defects caused by environment. Finally, the thesis puts forward simple ideas on how to bring the superiority into full play and expects that the adoption of wood-based composite technology for the prospect of wood products in the construction industry.

FIRE RETARDANT PERFORMANCE OF SUGI AND HINOKI TREATED WITH PHOSPHORUS AND NITROGEN FIRE RETARDANT

In this paper, ammonium phosphate polymer (APP), guanidinium phosphate urea (GUP), phosphonic acid, and a small number of additives that confer flame retardant properties were prepared as a new composite flame retardant. Cedar (Cryptomeria japonica) and hinoki (Chamaecyparis obtuse) penetrate and absorb the solution into the inner wall of the wood by vacuum pressurization, thus obtaining fire-retardant woods. The flame retardant effectsat different absorption amounts were investigated by thermogravimetric analysis and cone calorimetry.The absorption amounts of both kinds of wood above 0.095 g.cm-3and 0.085g.cm-3respectively, met the flame retardant standard ISO-5660-1: 2015. Thermogravimetric analysis showed that the fire-retardant-treated wood increased thermal stability, accelerated carbonization, and lower the decomposition temperature to below 300°C.

Extraction of plant parenchyma by computer image processing technology

People are increasingly using different kinds of plant products, such as wood, but there are many kinds of wood and it is difficult to analyze and identify them, so how to use auxiliary equipment to analyze wood and achieve the goal of accurate wood identification without damaging the product itself has become one of the important problems to be solved in the field of wood research. The axial thin-walled tissue has important wood grain information and it is one of the important features for wood identification. In this paper, we studied the microscopic images of broadleaf wood, and obtained the microstructure images of wood cross-section by photographing, and extracted the complete axial thin-walled tissue morphology of wood by using computer image processing technology and other ways about computer vision. Firstly, the axial thin-walled wood images were de-noised to eliminate some noise effects, so as to facilitate the separation of the axial thin-walled wood; then the images were processed by mathematical morphology to successfully extract the axial thin-walled wood and duct morphology from the cross-sectional images of broadleaf wood; finally, the axial thin-walled wood was separated from the duct by calculating the area of the closed area.

Chemotaxonomic identification of Chamaecyparis formosensis Matsumura and Chamaecyparis obtusa var. formosana (Hayata) Rehder using characteristic compounds of wood essential oils

Chamaecyparis formosensis Matsumura and C. obtusa var. formosana (Hayata) Rehder are important, precious, and well-known species grown in Asia. Renowned for excellent natural durability, their wood logs are regularly used as quality building materials or furniture. However, these two species have similar appearances, e.g., leaf, twig, wood, hardly distinguishable by the naked eye. The purpose of the present study is to phytochemically differentiate these two species using volatile compounds from the woods. Wood essential oils were obtained by 6-h hydrodistillation. The chemical composition was identified by GC-MS, and semi-quantification was carried out to determine the content of each compound. Furthermore, compounds with a significantly higher content than those of the other species were screened by t-test and principal component analysis (PCA). Results from semi-quantification and t-test showed that C. formosensis contained higher content of cis-myrtanol (ratio 37.1 ± 19.8), chamaecynone (11.0 ± 6.7), and α-eudesmol (8.5 ± 7.9), while C. obtusa var. formosana comprised mainly of α-terpineol (30.2 ± 10.1) and borneol (24.0 ± 16.1). Moreover, PCA results showed that the representative compounds of C. formosensis were cis-myrtanol and chamaecynone, while those of C. obtusa var. formosana were α-terpineol, borneol, and α-cadinol. Taken together, the above-mentioned results suggested significant compositional differences between these two species. For distinguishing the two kinds of wood, C. formosensis should be easily identified by its two characteristic compounds: cis-myrtanol and chamaecynone; while C. obtusa var. formosana could also be distinguished by its characteristic compounds: α-terpineol and borneol.

Uplift capacity evaluation of light-framed wood structure’s roof-to-wall connections

The load-displacement curves of six types of roof-to-wall connection joints were obtained through uplift experiments, while the mechanical properties of each type of joint were compared and analyzed, and the applicability of each joint was verified by the Foschi load-displacement curve model simulation. The specimens were made of three kinds of wood (Pinus sylvestris (PS), Spruce-Pine-Fir (SPF), and Douglas fir (DF)) and two different metal connectors (A-type and B-type), and then the monotonic pullout tests were conducted on each specimen. The failure modes of each group of specimens were analyzed, and the characteristic values analysis method was used to analyze and compare the characteristic values of the load-displacement curves of each specimen, including six characteristic values: maximum load, yield load, deformation capacity, energy dissipation capacity, ductility ratio, and initial stiffness. The results showed that the load capacity of TA group (specimens with A-type metal connectors) was much greater than that of TB group (specimens with B-type metal connectors). The specimens made of DF had the best mechanical performance, but the specimens of DF group were prone to brittle failure. Finally, the fitting parameters of the Foschi model applicable to such joints were obtained.

First Report of Leaf Spot Caused by Colletotrichum fructicola on Dalbergia hupeana in China.

Dalbergia hupeana is a kind of wood and medicinal tree widely distributed in southern China. Since 2019, a leaf spot disease was observed on the leaves of D. hupeana in Gangxia village, Luoting town in Jiangxi Province, China (28°52'53″N, 115°44'58″E). The disease incidence was estimated to be above 50%. The symptoms began as small spots that gradually expanded, developing a brown central and dark brown to black margin. The spots ranged from 4 to 6 mm in diameter. Leaf pieces (5 × 5 mm) from lesion margins were surface sterilized in 70% ethanol for 30 s followed by 2% NaOCl for 1 min and then rinsed three times with sterile water. Tissues were placed on potato dextrose agar (PDA) and incubated at 25°C. Pure cultures were obtained by monosporic isolation. Fifteen strains with similar morphological characterizations were isolated, and three representative isolates (JHT-1, JHT-2, and JHT-3) were chosen and used for further study. Colonies on PDA of three isolates were grayish-green with white edges and dark green on the reverse side. Conidia were transparent, cylindrical with rounded ends, and measured 3.6-5.3 µm × 9.5-15.2 µm (3.7 ± 0.2 × 13.6 ± 1.1 µm, n = 100). Appressoria were dark brown, globose or subcylindrical, and ranged from 6.2-9.2 µm× 5.1-6.8 µm (7.9 ± 0.4 × 5.9 ± 0.3 µm, n=100). The morphological characteristics of the three strains were consistent with the description of species in the Colletotrichum gloeosporioides complex (Weir et al. 2012). The internal transcribed spacer (ITS) regions, actin (ACT), calmodulin (CAL), chitin synthase (CHS-1) and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) and beta-tubulin 2 (TUB2) were amplified from genomic DNA for the three isolates using primers ITS1/ITS4, ACT-512F/ACT-783R, CL1/CL2, CHS-79F/CHS-345R, GDF/GDR and T1/Bt2b (Weir et al. 2012), respectively. The sequences were deposited in GenBank (Accession Nos. MZ482016 - MZ482018 for ITS; MZ463636 - MZ463638 for ACT; MZ463648- MZ463650 for CAL; MZ463639 - MZ463641 for CHS-1; MZ463642 - MZ463644 for GAPDH; MZ463645 - MZ463647 for TUB2). A neighbor-joining phylogenetic tree was constructed with MEGA 7.0 using the concatenation of multiple sequences (ITS, ACT, GAPDH, TUB2, CHS-1, CAL) (Kumar et al. 2016). According to the phylogenetic tree, three isolates fall within the Colletotrichum fructicola clade (boot support 99%). Based on morphological characteristics and phylogenetic analysis, three isolates were identified as C. fructicola. The pathogenicity of three isolates was conducted on two-yr-old seedlings (30 cm tall) of D. hupeana. Healthy leaves were wounded with a sterile needle and then inoculated with 10 μL spore suspension (106 conidia per mL). Controls were treated with sterile water. All plants were covered with transparent plastic bags and incubated in a greenhouse at 28°C with a 12 h photoperiod (relative humidity > 80%). Within five days, the inoculated leaves developed lesions similar to those observed in the field, whereas controls were asymptomatic. The experiments repeated three times showed similar results. The infection rate was 100%. C. fructicola was re-isolated from the lesions, whereas no fungus was isolated from control leaves. C. fructicola can cause leaf diseases in a variety of hosts, including Aesculus chinensis (Sun et al. 2020), Peucedanum praeruptorum (Ma et al. 2020), and Mandevilla × amabilis (Sun et al. 2020). C. brevisporum and C. gigasporum were also reported to infect Dalbergia odorifera (Chen et al. 2021; Wan et al. 2018). However, This is the first report of C. fructicola associated with leaf spot disease on D. hupeana in China. These results will help to develop effective strategies for appropriately managing this newly emerging disease.

The Hill Cumorah: Restoring a Sacred Site

The Hill Cumorah: Restoring a Sacred Site

Permittivity-Based Water Content Calibration Measurement in Wood-Based Cultural Heritage: A Preliminary Study.

In this work, the dielectric permittivity of four kinds of wood (Fir, Poplar, Oak, and Beech Tree), used in Italian Artworks and structures, was characterized at different humidity levels. Measurements were carried out using three different probes connected to a bench vector network analyzer: a standard WR90 X-band waveguide, a WR430 waveguide, and an open-ended coaxial probe. In particular, we investigated the dispersion model for the four wood species, showing how a log-fit model of the open-ended data presents a determination coefficient R2 > 0.990 in the 1–12 GHz frequency range. This result has proven helpful to fill the frequency gap between the measurements obtained at different water contents with the two waveguide probes showing an R2 > 0.93. Furthermore, correlating the log-fit vertical shift with the water content, it was possible to find a calibration curve with a linear characteristic. These experimental results will be helpful for on-site non-invasive water monitoring of wooden artworks or structures. Moreover, the final results show how the open-ended coaxial probe, with a measurement deviation lower than 7% from the waveguide measurements, may be used directly as a non-invasive sensor for on-site measurements.

Characterization and Storage Stability Study of Guava and Mango Wood Smoked Induced Spiced Cultured Milk (Raita)

A study was conducted to evaluate the effect of the smoking of raita with guava and mango wood on its functional properties and storage stability. The raita was smoked with guava and mango wood for 2.5, 5, 7.5, and 10 min in a closed chamber. The smoked raita was evaluated for change in titratable acidity (TA), pH, total phenolic content (TPC), antioxidant activity (DPPH), colour (L*, a*, and b*), and sensory attributes. Both guava and mango wood smoked samples didn’t show significant changes (P<0.05) in TA, pH, TPC, and antioxidant activity. All colour values (L*, a* and b*) of smoked samples were significantly (P<0.05) higher than the control sample, particularly, the yellowish attribute (b*) was very high in smoked samples. The sample that smoked for 7.5 min had very high overall acceptability scores in both kinds of wood and which is considered as an optimum smoking time for raita. The selected raita samples were stored for 9 days at 4°C and assessed for TA, pH, and standard plate count (SPC) at 3 days of interval. During the storage period, a significant reduction (P<0.05) in pH and a significant increase (P<0.05) in TA was seen till the 6th day of storage. The smoked samples had considerably lower SPC than the control sample and SPC was decreased significantly (P<0.05) with an increase in storage days in all the samples. The preparation is simple and can be served in Pubs/Bars, Casual Dining Restaurants & QSRs (Quick served restaurants).

Effect of Impregnation with Boron Compound Doped Rosin to the Combustion Resistance of Oriental Beech Wood (Fagus orientalis Lipsky)

In this study, investigation of the combustion properties of Oriental beech wood (Fagus orientalis Lipsky) impregnated with boron compound (borax (Na2B4O710H2O), boric acid (H3BO3) doped rosin (C19H29COOH) was aimed. For this purpose, Oriental beech wood samples were prepared according to ASTM E 160-50 and impregnated with boron compound doped rosin by the method of medium-term dipping (24 hours) according to ASTM D 1413 and producers’ definition. Combustion properties of samples after impregnated process were determined according to ASTM E 160-50. As a part of the research, 6 different combination and contents of impregnation materials have been used in order to especially investigate resistance against combustion of wood material treated with boron compounds in different concentrations. As a result of the study, retention performance and leaching resistance of boron compounds can be increased through rosin addition. Consequently, impregnation materials with rosin decreased the flame sourced combustion (Fsc) temperatures depending on kind of impregnation material, extended combustion period and decreased weight loss ratio of the test samples in comparison to the control samples. On the contrary, weight loss ratios were affected negatively in Oriental beech test samples up to 3% when compared with samples which were impregnated with borax. Meanwhile, combustion periods increased in test samples up to 30%. Rosin, in terms of its combustion performance, can be preferred in impregnation with boron compounds depending on kind of wood and using area.