Ion-exchange Stationary Phases Research Articles

Study of Efficiency of Capacity Gradient Ion-Exchange Stationary Phases

Highly efficient columns are necessary for the modern analytical applications of liquid chromatography. In this work, the separation efficiency of ion-exchange capacity gradient stationary phases combined with eluent concentration gradient was studied by a theoretical approach. In the course of our work three different scenarios of capacity gradients were used with different shapes (linear, convex and concave). The resolutions of different gradient columns were calculated for each scenario. As a reference, a uniform column was considered, which had the same analysis time as the non-uniform column. In the case of separation of ions with same charges, the gradient column offered only a marginal advantage compared to the uniform column due to the bandwidth compression caused by the capacity gradient. In the case of ions with different charges, however, the advantage of the gradient column was more significant. This was mainly due to the increased retention time difference of solutes. Ion-exchange capacity gradient columns may be a new way to separate ions more efficiently.

Complex Protein Retention Shifts with a Pressure Increase: An Indication of a Standard Partial Molar Volume Increase during Adsorption?

Studies of protein adsorption on reversed-phase and ion exchange stationary phases demonstrated an increase in retention with increasing pressure, which is interpreted as a standard partial molar volume decrease during the transition of the protein from a mobile to a stationary phase. Investigation of the pressure effect on the retention of lysozyme and IgG on a cation exchange column surprisingly revealed a negative retention trend with the increase of pressure. Further investigation of this phenomenon was performed with β-lactoglobulin, which enabled adsorption to be studied on both cation and anion exchange columns using the same mobile phase with a pH of 5.2. The same surface charge and standard partial molar volume in the mobile phase allowed us to examine only the effect of adsorption. Interestingly, a negative retention trend with a pressure increase occurred on an anion exchange column while a positive trend was present on a cation exchange column. This indicates that the interaction type governs the change in the standard partial molar volume during adsorption, which is independent of the applied pressure. Increasing the protein charge by decreasing the pH of the mobile phase to 4 reversed the retention trend (into a negative) with a pressure increase on the cation exchange column. A further decrease of the pH value resulted in an even more pronounced negative trend. This counterintuitive behavior indicates an increase in the standard partial molar volume during adsorption with the protein charge, possibly due to intermolecular repulsion of adsorbed protein molecules. While a detailed mechanism remains to be elucidated, presented results demonstrate the complexity of ion exchange interactions that can be investigated simply by changing the column pressure.

Conformational changes impact 3D antibody translational dynamics during separation through an ion exchange membrane

Antibody-based therapeutics are a fast-growing sector in the pharmaceutical industry. One large contributor to the high cost associated with development of new antibody therapeutics is the separation and purification process, which is currently iterative and empirical. More information about how antibodies interact with stationary phases would be helpful in improving the process. I will discuss our recent efforts to track single, fluorescently labeled antibodies as they interact with an ion-exchange stationary phase.

Quantitative analysis of free glycerol in biodiesel using solid-phase extraction and high-performance liquid chromatography

This study developed a method for separating and quantifying free glycerol in biodiesel. The free glycerol in biodiesel samples was separated using solid-phase extraction (SPE) and subsequently quantified by high-performance liquid chromatography (HPLC) using an ion-exchange stationary phase and refractive index detector (IR). The proposed method (SPE-HPLC-IR) was validated for high- and low-concentration samples (coefficient of determination, R2≥0.99): limit of detection (0.00029% m/m, high; 0.00018% m/m, low); limit of quantification (0.00089% m/m, high; 0.00054% m/m, low); precision (standard deviation < 5.0%), and accuracy (recovery of 98.93% to 106.71%). The proposed method was compared with the reference method (ASTM D6584) using the paired t-test, and no statistical differences were found between them (95% confidence). As such, the proposed method offers a simple, quick, effective method for determining free glycerol in biodiesel and a viable alternative to the reference method.

Strong cation- and zwitterion-exchange-type mixed-mode stationary phases for separation of pharmaceuticals and biogenic amines in different chromatographic modes

A set of new mixed-mode ion-exchange stationary phases is presented. The backbone of organic selectors is formed by a linear hydrocarbon chain, which is divided into two parts of various lengths by a heteroatom (oxygen or nitrogen). In all studied cases, there is a sulfonic acid moiety as the terminal group. Therefore, selectors bearing oxygen gave rise to strong cation ion-exchange stationary phases, while selectors with an embedded nitrogen atom (inducing a weak anion exchange capacity) were used to create zwitterion ion-exchange stationary phases. The new mixed-mode stationary phases were chromatographically evaluated in high performance liquid chromatography (HPLC) and supercritical fluid chromatography (SFC) using isocratic elution conditions to disclose their chromatographic potential. In HPLC mode, aqueous-rich reversed phase chromatography, acetonitrile-rich hydrophilic interaction liquid chromatography and methanolic ion-exchange chromatography mobile phases were employed. In these chromatographic modes, retention factors and selectivity values for a test set of basic and zwitterionic analytes were determined. The results were compared and principal component analysis for each chromatographic mode was performed. For all chromatographic modes, the component 1 in the principal component analysis reflected the elution order. The application of different mobile phases on a particular column resulted not only in variation in retention, but also in modified selectivity, and different elution order of the analytes. The orthogonality of the elution order depending on the employed mobile phase conditions was especially reflected for structurally closely related analytes, such as melatonin and N-acetyl-serotonin, tryptamine and serotonin or noradrenalin and octopamine. However, ion-exchange interactions remain the main driving force for retention. From all investigated stationary phases, the SCX 2 (C5-linker and C4-spacer) seems to be the best choice for the separation of basic analytes using different mobile phase conditions.

Application of dendrimer-functionalized ion-exchange stationary phases for the retention and separation of low-molecular-weight heparins

The disaccharides of low-molecular-weight heparins (LMWH) obtained by enzymatic depolymerization most frequently require a determination method that uses separation techniques.

Ion exchange in supercritical fluid chromatography tandem mass spectrometry (SFC-MS/MS): Application for polar and ionic drugs and metabolites in forensic and anti-doping analysis

Supercritical fluid chromatography (SFC) is an orthogonal technique to UHPLC. In recent years, SFC has demonstrated potential for use in the analysis of a broad variety of analytes of different polarities, if modifiers and additives are utilized as additional mobile phase constituents. However, to date, little research has been carried out on ion-exchange separation of highly polar and ionic analytes using SFC.The objective of this work was to investigate the elution characteristics of polar compounds using SFC combined with tandem mass spectrometry. Highly polar and even ionic drugs and metabolites, with a diversity of functional groups such as gamma-hydroxybutyrate (GHB), gamma-butyrolactone, GHB-glucuronide, ethyl sulfate, ethyl glucuronide as well as meldonium and gamma-butyrobetaine, were selected for the study. To investigate the chromatographic behavior of the solutes using SFC, a systematic chromatographic method development workflow including a basic validation in human urine was implemented. To ensure the best selectivity, columns with different stationary phase chemistries (silica, NH2, CN, SCX, Diol, EP and amide) were screened. Furthermore, different modifier compositions were evaluated, including pure methanol and methanol with various additives (ammonium acetate or ammonium formate, water, and/or ammonia or formic acid in varying amounts). Trends in retention time shifts were investigated by the systematic variation of gradients, backpressure and column compartment temperature. The quality and reliability of the method has been tested in the course of a basic validation by evaluation of selectivity, linearity, limit of identification, limit of quantification, carry-over, precision, and matrix effect.The highest chromatographic selectivity (especially with respect to the separation of the critical pair of zwitterionic meldonium and γ-butyrobetaine) and suitable peak shapes for all target analytes were obtained using the strong cation exchange column. We observed that increasing buffer concentrations improved the peak shape. Ion-exchange stationary phase and polar additives (buffers, bases, acids and water) mixed with organic modifiers enabled separation of small ionic molecules using SFC. Hence, SFC further demonstrated its wide applicability in small molecule analysis, and may be considered an alternative separation technique to improve the separation of polar analytes.

Electrospun Nafion-Polyacrylonitrile nanofibers as an ion exchange ultrathin layer chromatographic stationary phase

An ion-exchange method to separate charged biomolecules on ultrathin layer chromatographic (UTLC) plates using electrospun Nafion-Polyacrylonitrile (PAN) nanofibers as the stationary phase is described. Sulfonate groups on Nafion provide the ion-exchange sites. The addition of PAN (a higher molecular weight polymer than Nafion) was used to facilitate the nanofiber formation process using electrospinning. Electrospinning parameters and separation conditions were optimized using fractional factorial design and response surface methodology. Nafion-PAN nanofibers containing 45% (w/w) Nafion with 0.407 mmol/g of SO3H group and 16.0 mmol/g of fluorine as an ion exchange stationary phase for UTLC were evaluated using the separations of amino acids and proteins, followed by visualizations using ninhydrin and fluorescamine, respectively. The electrospun Nafion-PAN plates showed high chemical stability under various mobile phase conditions. Mobile phase velocity decreased with the addition of Nafion into the electrospinning solutions. The sources of band broadening of analyte spots were investigated. The separation of amino acids showed high selectivity and separation efficiency. The separation of four proteins demonstrated the feasibility of Nafion-PAN UTLC for separating large biomolecules.

Multiple, simultaneous, independent gradients for a versatile multidimensional liquid chromatography. Part II: Application 2: Computer controlled pH gradients in the presence of urea provide improved separation of proteins: Stability influenced anion and cation exchange chromatography

This paper details the use of a method of creating controlled pH gradients (pISep) to improve the separation of protein isoforms on ion exchange (IEX) stationary phases in the presence of various isocratic levels of urea. The pISep technology enables the development of computer controlled pH gradients on both cationic (CEX) and anionic (AEX) IEX stationary phases over the very wide pH range from 2 to 12. In pISep, titration curves generated by proportional mixing of the acidic and basic pISep working buffers alone, or in the presence of non-buffering solutes such as the neutral salt NaCl (0–1M), polar organics such as urea (0–8M) or acetonitrile (0–80 Vol%), can be fitted with high fidelity using high order polynomials which, in turn allows construction of a mathematical manifold %A (% acidic pISep buffer) vs. pH vs. [non-buffering solute], permitting precise computer control of pH and the non-buffering solute concentration allowing formation of dual uncoupled liquid chromatographic (LC) gradients of arbitrary shape (Hirsh and Tsonev, 2012 [1]). The separation of protein isoforms examined in this paper by use of such pH gradients in the presence of urea demonstrates the fractionation power of a true single step two dimensional liquid chromatography which we denote as Stability-Influenced Ion Exchange Chromatography (SIIEX). We present evidence that SIIEX is capable of increasing the resolution of protein isoforms difficult to separate by ordinary pH gradient IEX, and potentially simplifying the development of laboratory and production purification strategies involving on-column simultaneous pH and urea unfolding or refolding of targeted proteins. We model some of the physics implied by the dynamics of the observed protein fractionations as a function of both urea concentration and pH assuming that urea-induced native state unfolding competes with native state electrostatic interaction binding to an IEX stationary phase. Implications for in vivo protein-membrane interactions are discussed.

Polystyrene-divinylbenzene-glycidyl methacrylate stationary phase grafted with poly (amidoamine) dendrimers for ion chromatography

In this work, a novel ion exchange stationary phase based on different generations of poly (amidoamine) dendrimers (PAMAM) was developed for the determination of inorganic anions and carbohydrates. Synthesis of the PAMAM was carried out with the polymerization reaction of ethylenediamine and methyl acrylate. The synthesized PAMAM was then grafted to the polystyrene-divinylbenzene-glycidyl methacrylate (PS-GMA) to form PAMAM-based beads. These beads were finally modified with 1,4-butanediol diglycidyl ether (BDDE) to generate the anion exchanger, which were characterized by scanning electron microscopy (SEM), brunauer-emmett-teller (BET), fourier transform infrared spectroscopy (FTIR), and elemental analysis. Elemental analysis, breakthrough curves and capacity factors showed that more epoxy groups and higher PAMAM generations in stationary phase could result in higher anion exchange capacity. The efficiency, durability and stability of the proposed anion exchanger were investigated by using six inorganic anions (fluoride, chloride, nitrite, bromide, nitrate and sulfate) and four carbohydrates (trehalose, glucose, maltotriose and galacturonic acid) as analytes, respectively. The reliability of the proposed ion chromatographic stationary phase was demonstrated by determining the content of galacturonic acid in polysaccharides from Poria cocos and Atractylodes macrocephala. The relative standard deviations of retention time, peak height, and peak area for galacturonic acid were 0.39%, 1.22%, and 2.02%, respectively. The spiked recoveries were in the range of 88.29%–100.51% for plant polysaccharides. Due to the good structural homogeneity, intense internal porosity, biological compatibility and high density of active groups in PAMAM, this grafted stationary phase showed good ion-exchange characteristics, especially in biological charged molecules.

Preparation of an agglomerated ion chromatographic stationary phase with 2,3-ionene and its application in SO4(2-) analysis

The poly-electrolyte cation functional group of 2,3-ionene was synthesized with tetramethyl ethylenediamine and 1,3-dibromopropane as the raw materials. Multiporous polystyrene-divinylbenzene microsphere particles (PS-DVB) were produced by swelling method with polystyrene as seeds and sulfonated. Then the 2,3-ionene was bonded on the sulfonated multi-porous polystyrene-divinylbenzene microsphere particles by agglomeration to get the agglomerative ion-exchange stationary phase. After optimizing the synthetic conditions, the new stationary phase was characterized by the techniques including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and elemental analysis. The chromatographic column was packed by slurry method and applied in the analysis of SO4(2-) with a conductivity detector. SO4(2-) and other six common anions including F-, Cl-, NO2(-), Br-, NO3(-), PO4(3-), were separated and analyzed rapidly on the self-regulating chromatographic column within 8 min. The linear range was from 0.5 to 50 mg/L with correlation coefficient (r) of 0.9992. The LOD was 0.04 mg/L with S/N of 3. The relative standard deviations (RSDs, n = 6) were 2.4% and 3.1% for the peak area and retention time, respectively. The recoveries were between 99.2% and 101.8%. The retention times of SO4(2-) did not change significantly after long time use of the self-regulating chromatographic column. The self-regulating chromatographic column is suitable for the detection of SO4(2-) in complex matrix samples.

Orthogonal separation and identification of long-chain peptides from scorpion Buthus martensi Karsch venom by using two-dimensional mixed-mode reversed phase-reversed phase chromatography coupled to tandem mass spectrometry

Peptide components of scorpion venom have been employed as useful pharmacological tools in the study of ion channel function. The isolation of individual components is necessary for determination of their biological significance. Here, we have described a novel reversed phase (RP)/ion exchange stationary phase, Click oligo ethylene glycol (Click OEG), and the chromatographic efficiency of its mixed-mode sorbent in peptide separation experiments. The Click OEG presents a mixed-mode RP/weak anion-exchange type stationary phase at pH 3.5 and mixed-mode RP/weak cation-exchange type stationary phase at pH 6.0, and it was suitable for separation of long-chain peptides in scorpion venom. Subsequently, a two dimensional mixed-mode RP-RP system based Click OEG and C18 with different pH values in two dimensions was developed for orthogonal separation of scorpion venom. Furthermore, two fractions were analyzed in depth, and 11 long-chain peptides were purified and sequences were identified by using tandem mass spectrometry incorporating the tryptic approach. Among these, we isolated six novel peptides including one peptide with a new sequence and five transcript-level peptides, and speculated on their possible bioactivities.

Transport Characteristics of Aromatic Acids in the Capillary Electrochromatography with Mixed Magnetic Nanoparticles Coating as Stationary Phase

In this paper, novel open-tubular electrochromatographic system with core/shell magnetic nanoparticles modified by amino and C18 functional groups as mixed stationary phase by using a series of permanent magnets to immobilize nanoparticles into the capillary were investigated. The new system showed high separation ability and efficiency due to high specific surface area of nanomaterial and mixing separation mechanism. The transport equations of aromatic acids using the open-tubular electrochromatographic column with magnetic nanoparticle coating as stationary phases were derived under isocratic and double stepwise gradient elutions, and the retention characteristics of organic acids separated by the columns were further investigated. The results showed that the electroosmotic flow gradually decreased with the increase of Fe3O4@SiO2-NH2 in the mixed stationary phases, and the direction of electroosmotic flow reversed eventually. The capacity factor was relevant to the ratio of ion-exchange and reversed-phase stationary phases. Furthermore, experiments confirmed that the capacity factor of solute had a good linear relationship with the ratio of mixed stationary phases, and the correlation coefficient was greater than 0.9166 after fitting. Under the double stepwise gradient elution condition, the migration time of solute can be predicted by its elution time under isocratic elution. After the solutes were eluted by phosphate buffer stepwise gradient elution, the relative errors between predicted retention time and actual retention time of solute were less than 8.0%. After they were eluted by organic modifier concentration stepwise gradient elution, the relative errors between two values of solute were less than 10%. After they were eluted by pH value stepwise gradient elution, the relative errors between two val- ues of solute were less than 5.8%. Rhizoma gastrodiae was separated by the constructed system under the optimized chroma- tographic condition, the main components of gastrodin, vanilla alcohol and citric acid were identified based on retention time of standards, and the relative errors between predicted value and actual value of citric acid was 11%. The open-tubular elec- trochromatographic system shows great potential in the method development of analysis of complicated samples. Keywords gradient elution; transport characteristic; mixed stationary phase 1 引言

Separation Behavior of U(VI) and Th(IV) on a Mixed Ion Exchange Column Using 2,6-Pyridine Dicarboxylic Acid as a Complexing Agent and Determination of Trace Level Thorium in Uranium Matrix Employing High Performance Ion Chromatography

Retention behavior of U(VI) and Th(IV) as their 2, 6-pyridine dicarboxylic acid (PDCA) complexes on reversed phase and ion exchange (cation, anion and mixed ion exchange) columns was studied and based on the results, a simple ion chromatography method for the determination of trace level thorium in uranium oxide using 0.075mM 2, 6-pyridine dicarboxylic acid (PDCA) and 1M KNO3 in 1.2M HNO3 as eluent (flow rate 1 mL/min)was proposed. The advantage of the developed method is that the separation of uranium matrix is not required prior to the ion chromatographic determination of trace Th. Separation was carried out on a mixed ion exchange stationary phase and a 10?4 M arsenazo (III) solution was used as post column reagent for detecting the separated metal ions. The separation of Th from uranium using PDCA in the present investigation is attributed through cation exchange mechanism. A calibration plot was constructed by following the standard addition method over the concentration range of 0.25 to 10 ppm of Th in the presence of uranium matrix, which resulted in a linear regression coefficient of 0.9978. The precision of the method was better than 5% and the LOD for Th was found to be 0.1ppm (S/N=3). The method has been validated by comparing the results with the results obtained from ICP-MS analysis where the This separated from the uranium matrix. The proposed method is simple, rapid, accurate and cost effective compared to techniques like ICP-MS or ICP-AES and is suitable for the routine kind of analysis.

High performance ion chromatography of transition metal chelate complexes and aminopolycarboxylate ligands

A simple ion chromatographic method was developed for the separation of transition metal chelates (CuEDTA, CuDCTA, ZnEDTA, ZnDCTA) and free anionic complexing ligands (EDTA, DCTA) using alkaline carbonate eluents and conductivity detection. The complex equilibria and kinetic process of separations were studied in order to understand major factors in the control of selectivity and retention order of complex anions. A systematic study was applied to identify the additional peaks of the system as NaEDTA3−, NaHEDTA2−, Na2EDTA2−, EDTA4−/HEDTA3−, DCTA4−/HDCTA−3. On the basis of microequilibrium considerations of chelating ligand, it was shown that one should expect the peaks of sodium chelates when the ligand is in excess in the sample solution. The probability density function was introduced for calculation of complex chromatograms, because complexing ligands can exist in at least two different interconvertible forms in the presence of metal ion. The chromatogram of interconverting chelate species can be given as the sum of probability density functions (P) weighed by the molar fractions of complexed (ΦML) and dissociated (ΦL) forms. The influences of kinetic rate of complex formation and dissociation on the distribution of components between eluents and ion exchange stationary phases were quantitatively described and demonstrated by elution profiles. The applicability of the developed method is represented by the simultaneous analysis of transition metal chelates and inorganic anions. ICP-AES analysis and FTIR-ATR technique were used for confirmation of IC results for metals and ligands, respectively. Collection protocols for the heart-cutting procedure of chromatograms were applied in the analysis of target components. The limit of detection and linearity of the method in the range of 0.01–0.25mM sample concentration were also presented.

Preparation of α‐Aminobenzylphosphonic Acids with a Stereogenic Quaternary Carbon Atom via Microscopically Configurationally Stable α‐Aminobenzyllithiums

The enantiomers of 1-phenylethylamine were phosphorylated with diethyl chlorophosphate/Et(3)N and then Boc-protected (Boc=tert-butoxycarbonyl) at the nitrogen atom. These phosphoramidates were metalated by using sBuLi/N,N,N',N'-tetramethylethylenediamine (TMEDA) to give alpha-aminobenzyllithiums that isomerised to alpha-aminophosphonates in yields of up to 80 % with retention of the configuration at the carbon atom. The intermediate tertiary organolithiums were found to be microscopically configurationally stable from -78 to 0 degrees C in Et(2)O. The protected alpha-aminophosphonates were deblocked by using boiling 6 M HCl or preferably Me(3)SiBr/(allyl)SiMe(3). When the Boc group was replaced by the diethoxyphosphinyl group, the alpha-aminobenzyllithium intermediate partially enantiomerised even at -78 degrees C and rearranged to yield an alpha-aminophosphonate with 50 % ee (ee=enantiomeric excess). Similarly, N-Boc-protected phosphoramidates derived from racemates and/or enantiomers of 1-(1-naphthyl)ethyl-, 1-indanyl- and 1,2,3,4-tetrahydro-1-naphthylamine or 1-azidoindan- and 1-azido-1,2,3,4-tetrahydronaphthalene were converted to aminophosphonates in good yields. Deblocking gave alpha-aminophosphonic acids of excellent enantiomeric excess (97-99 %), as determined by means of HPLC on a chiral ion-exchange stationary phase based on quinine carbamate. When racemic Boc-protected diethyl phosphoramidate derived from 1,2,3,4-tetrahydro-1-naphthylamine was metalated with LiTMP/TMEDA (TMP=2,2,6,6-tetramethylpiperidine), 1-hydroxyethylphosphonamidates resulted. The configuration of the main isomer was determined by means of a single-crystal X-ray structure analysis.

Theory and applications of a novel ion exchange chromatographic technology using controlled pH gradients for separating proteins on anionic and cationic stationary phases

pISep is a major new advance in low ionic strength ion exchange chromatography. It enables the formation of externally controlled pH gradients over the very broad pH range from 2 to 12. The gradients can be generated on either cationic or anionic exchangers over arbitrary pH ranges wherein the stationary phases remain totally charged. Associated pISep software makes possible the calculation of either linear, nonlinear or combined, multi-step, multi-slope pH gradients. These highly reproducible pH gradients, while separating proteins and glycoproteins in the order of their electrophoretic pIs, provide superior chromatographic resolution compared to salt. This paper also presents a statistical mechanical model for protein binding to ion exchange stationary phases enhancing the electrostatic interaction theory for the general dependence of retention factor k, on both salt and pH simultaneously. It is shown that the retention factors computed from short time isocratic salt elution data of a model protein can be used to accurately predict its salt elution concentration in varying slope salt elution gradients formed at varying isocratic pH as well as the pH at which it will be eluted from an anionic exchange column by a pISep pH gradient in the absence of salt.

Characterization of ion exchange stationary phases via pH transition profiles

New non-destructive method for characterization of ion exchange chromatographic columns based on transient pH formed by a step change in ionic strength of buffer solutions was examined. The method was used to distinguish between cation and anion or weak and strong ion exchange chromatographic supports and to determine the capacity of the chromatographic resins. The general scheme to distinguish between most commonly used types of ion exchange chromatographic columns was proposed. The duration of pH transient was shown to be linearly proportional to the total ionic capacity and was used to estimate protein dynamic binding capacity of the resin. The effects of pH, concentration and temperature on transient pH duration were examined.

Towards high capacity latex-coated porous polymer monoliths as ion-exchange stationary phases

The preparation of high capacity agglomerated monolithic ion-exchangers for capillary ion chromatography is described. Post-modification of reactive monoliths was investigated as an alternative to co-polymerisation of a suitable functional monomer with an overarching goal of increasing ion-exchange capacity. Direct sulfonation of poly styrene-co-divinyl benzene monoliths using concentrated sulfuric acid or chlorosulfonic acid was unsuccessful even for monoliths containing as low as 8% crosslinker. In contrast, chemical transformation of reactive monoliths containing glycidyl methacrylate was used to increase the ion-exchange capacity by up to more than thirty-fold with ion exchange capacities of 14-29 microequiv g(-1) achieved. Three different reactions were considered, including reaction with 4-hydroxybenenesulfonic acid under basic conditions; reaction with thiobenzoic acid followed by transformation to a reactive thiol and the subsequent oxidation to the sulfonic acid; and direct sulfonation with sodium sulfite. Of these, the reaction with sodium sulfite resulted in the most significant increase in the capacity and the best separation performance. In the isocratic mode separation efficiencies of over 13,500 plates m(-1) were observed (for iodate). The separation of seven inorganic anions was also demonstrated using a hydroxide gradient.

Evaluation of capillary ion exchange stationary phase coating distribution and stability using radial capillary column contactless conductivity detection

The use of radial (across) capillary column capacitively coupled contactless conductivity detection is demonstrated as a simple and rapid technique for visualisation of stationary phase longitudinal coverage and coating stability in capillary ion exchange chromatography.