Interfacial Impedance Research Articles

Conjugation Linked PEDOT:PSS with Low Impedance and High Stretchability for Epidermal Electrophysiology.

Long-term epidermal recording of bioelectricity is of paramount importance for personal health monitoring. It requires stretchable and dry film electrodes that can be seamlessly integrated with skin. The simultaneous achievement of high conductivity and skin-like ductility of conducting materials is a prerequisite for reliable signal transduction at the dynamic interface, which is also the bottleneck of epidermal electrophysiology. Here, carbon nanotubes (CNTs) are introduced as "conjugation linkers" into a topologically plasticized conducting polymer (PEDOT:PSS). A thin-film electrode with high conductivity (≈3250Scm-1) and high stretchability (crack-onset strain>100%) is obtained. In particular, the conjugation linker enables the high volumetric capacitance and the low film resistance, both of which synergically reduce the interfacial impedance. The capabilities of this electrode is further demonstrated in the precise recording of various electrophysiological signals.

Radially distributed charging time constants at an electrode-solution interface

An electrochemically homogeneous electrode-solution interface should be understood as spatially invariant in both terms of intrinsic reactivity for the electrode side and electrical resistance mainly for the solution side. The latter remains presumably assumed in almost all cases. However, by using optical microscopy to spatially resolve the classic redox electrochemistry occurring at the whole surface of a gold macroelectrode, we discover that the electron transfer occurs always significantly sooner (by milliseconds), rather than faster in essence, at the radial coordinates closer to the electrode periphery than the very center. So is the charging process when there is no electron transfer. Based on optical measurements of the interfacial impedance, this spatially unsynchronized electron transfer is attributed to a radially non-uniform distribution of solution resistance. We accordingly manage to eliminate the heterogeneity by engineering the solution resistance distribution. The revealed spatially-dependent charging time ‘constant’ (to be questioned) would help paint our overall fundamental picture of electrode kinetics.

Electrical Interface Parameters of PEDOT:PSS: Effect of Electrodeposition Charge Evaluated Under Body Conditions for Neural Electrode Applications

This study explores the influence of the deposition charge of poly(3,4-ethylenedioxythiophene) doped with polystyrene sulfonate (PEDOT:PSS) on its electrical interface parameters. For this purpose, PEDOT:PSS was fabricated by electrodeposition on commercial platinum electrodes with the time limited by different charges (1, 3, 6, 9 mC). Further, the electrodes were characterized regarding their electrical interface such as interfacial impedance, potential window, double-layer capacitance, charge storage capacity, and current injection limit under simulated body conditions. The work showed whether and to what extent the change of deposition charge affected the electrical interface parameters of PEDOT:PSS-based platinum electrodes. The electrodes polymerized with 9 mC exhibited a significant increase in specific capacitance, indicating enhanced charge storage capacity. Additionally, this sample demonstrated lower resistance in phosphate-buffered saline, suggesting improved conductivity.

Viscoelastic Adhesive, Super-Conformable, and Semi-Flowable Liquid Metal Eutectogels for High-Fidelity Electrophysiological Monitoring.

Integrating gels with human skin through wearables provides unprecedented opportunities for health monitoring technology and artificial intelligence. However, most conductive hydrogels, organogels, and ionogels lack essential environmental stability, biocompatibility, and adhesion for reliable epidermal sensing. In this study, we have developed a liquid metal eutectogel simultaneously possessing superior viscoelasticity, semiflowability, and mechanical rigidity for low interfacial skin impedance, high skin adhesion, and durability. Liquid metal particles (LMPs) are employed to generate free radicals and gallium ions to accelerate the polymerization of acrylic acid monomers in a deep eutectic solvent (DES), obtaining highly viscoelastic polymer networks via physical cross-linking. In particular, graphene oxide (GO) is utilized to encapsulate the LMPs through a sonication-assisted electrostatic assembly to stabilize the LMPs in DES, which also enhances the mechanical toughness and regulates the rheological properties of the eutectogels. Our optimized semi-flowable eutectogel exhibits viscous fluid behavior at low shear rates, facilitating a highly conformable interface with hairy skin. Simultaneously, it demonstrates viscoelastic behavior at high shear rates, allowing for easy peel-off. These distinctive attributes enable the successful applications of on-skin adhesive strain sensing and high-fidelity human electrophysiological (EP) monitoring, showcasing the versatility of these ionically conductive liquid metal eutectogels in advanced personal health monitoring.

Unraveling the Intrinsic Origin of the Superior Sodium-Ion Storage Performance of Metal Selenides Anode in Ether-Based Electrolytes.

Metal selenides show outstanding sodium-ion storage performance when matched with an ether-based electrolyte. However, the intrinsic origin of improvement and deterministic interface characteristics have not been systematically elucidated. Herein, employing FeSe2 anode as the model system, the electrochemical kinetics of metal selenides in ether and ester-based electrolytes and associated solid electrolyte interphase (SEI) are investigated in detail. Based on the galvanostatic intermittent titration technique and in situ electrochemical impedance spectroscopy, it is found that the ether-based electrolyte can ensure fast Na+ transfer and low interface impedance. Additionally, the ether-derived thin and smooth double-layer SEI, which is critical in facilitating ion transport, maintaining structural stability, and inhibiting electrolyte overdecomposition, is concretely visualized by transmission electron microscopy, atomic force microscopy, and depth-profiling X-ray photoelectron spectroscopy. This work provides a deep understanding of the optimization mechanism of electrolytes, which can guide available inspiration for the design of practical electrode materials.

Opening and Constructing Stable Lithium-ion Channels within Polymer Electrolytes.

Lithium-ion batteries play an integral role in various aspects of daily life, yet there is a pressing need to enhance their safety and cycling stability. In this study, we have successfully developed a highly secure and flexible solid-state polymer electrolyte (SPE) through the in situ polymerization of allyl acetoacetate (AAA) monomers. This SPE constructed an efficient Li+ transport channel inside and effectively improved the solid-solid interface contact of solid-state batteries to reduce interfacial impedance. Furthermore, it exhibited excellent thermal stability, an ionic conductivity of 3.82×10-4 S cm-1 at room temperature (RT), and a Li+ transport number (tLi+) of 0.66. The numerous oxygen vacancies on layered inorganic SiO2 created an excellent environment for TFSI- immobilization. Free Li+ migrated rapidly at the C=O equivalence site with the poly(allyl acetoacetate) (PAAA) matrix. Consequently, when cycled at 0.5C and RT, it displayed an initial discharge specific capacity of 140.6 mAh g-1 with a discharge specific capacity retention rate of 70 % even after 500 cycles. Similarly, when cycled at a higher rate of 5C, it demonstrated an initial discharge specific capacity of 132.3 mAh g-1 while maintaining excellent cycling stability.

Opening and Constructing Stable Lithium‐ion Channels within Polymer Electrolytes

AbstractLithium‐ion batteries play an integral role in various aspects of daily life, yet there is a pressing need to enhance their safety and cycling stability. In this study, we have successfully developed a highly secure and flexible solid‐state polymer electrolyte (SPE) through the in situ polymerization of allyl acetoacetate (AAA) monomers. This SPE constructed an efficient Li+ transport channel inside and effectively improved the solid‐solid interface contact of solid‐state batteries to reduce interfacial impedance. Furthermore, it exhibited excellent thermal stability, an ionic conductivity of 3.82×10−4 S cm−1 at room temperature (RT), and a Li+ transport number (tLi+) of 0.66. The numerous oxygen vacancies on layered inorganic SiO2 created an excellent environment for TFSI− immobilization. Free Li+ migrated rapidly at the C=O equivalence site with the poly(allyl acetoacetate) (PAAA) matrix. Consequently, when cycled at 0.5C and RT, it displayed an initial discharge specific capacity of 140.6 mAh g−1 with a discharge specific capacity retention rate of 70 % even after 500 cycles. Similarly, when cycled at a higher rate of 5C, it demonstrated an initial discharge specific capacity of 132.3 mAh g−1 while maintaining excellent cycling stability.

LPEO enhanced LAGP composite solid electrolytes for lithium metal batteries

The application of solid electrolyte is expected to realize the commercialization of high energy density lithium metal batteries (LMBs). While the interfacial contact between solid inorganic electrolyte and electrodes has become a stumbling block for achieving stable cycling in LMBs. In this work, a Li-containing polyethylene oxide (LPEO) was introduced between LAGP and electrodes as a buffer layer to regulate the interfacial compatibility and reduce interfacial impedance, inhibiting the side reactions. Moreover, ether-oxygen bond on LPEO chain can coordinate with Li+ and guide the transportation of Li+, achieving fast Li+ diffusion between Li1+xAlxGe2-x(PO4)3 (LAGP) and electrodes. Specifically, the growth of lithium dendrites is effectively suppressed in LAGP with LPEO modification, which would lead to remarkable cycling stability and rate capability. Therefore, the Li|LPEO-LAGP|Li battery can cycle stably for more than 600 h at 0.1 mA cm−2. In addition, long-term performance of Li|LPEO-LAGP| LiFePO4 (LFP) battery was achieved at a rate of 0.4 C, and capacity retention is more than 74% after 200 cycles. The Li|LPEO-LAGP|LiNi0.8Co0.1Mn0.1O2 also realized the steady operation in the voltage range of 2.8–4.3 V.

P-modified carbon nanosheet with abundant through-hole channels for boosting Zn-ion storage under low-temperature

Zinc-ion hybrid capacitors (ZIHCs) as a promising energy storage system suffer from unsatisfactory capability due to mismatched pore structure and lack of active sites in the carbon cathodes. Herein, a coupling strategy of oxidation template and in-situ doping is proposed to design a P-modified carbon nanosheet with abundant through-hole channels. Phosphorus doping not only reduces the electrode/electrolyte interface impedance, but also increases the available active sites. Through-hole channels enhance the Zn2+ accessibility. Therefore, the assembled ZIHCs provide an ultra-high energy density of 194.23 Wh kg−1. Even at 0 °C, the ZIHCs retain a superior capacity of 166.0 mAh/g and stabilize for 10,000 cycles with capacity retention of 95.33 %. This work provides new insights into the design of carbon cathodes for boosting the Zn2+ storage.

FracAbut: A python toolbox for computing fracture stratigraphy using interface impedance

In Naturally Fractured Reservoirs (NFR) diffuse fractures arrangement results from mechanical stratigraphy and tectonic history during failure. Thus, modelling Discrete Fracture Network (DFN) requires to understand and to account for fracture relationships at bed-interface (abutment or crosscutting) in 3D through time (loading path). However, sampling fractures data meaningfully in subsurface has always been a challenge for geologist due to data scarcity.To better understand and forecast fracture networks in stratified rocks, we study outcrops with a focus on geometric relationships between stratigraphic interfaces and fractures. This paper presents an original python toolbox called FracAbut. It is composed of 1 main and 2 auxiliary codes that quantify the geometric relation between fractures and stratigraphic interfaces from 1D (wells, scan-line) and 2D (digital image, photographs data). We calculate the Interface Impedance (II) that accounts for fracture abutment (crossing or not), persistence (single- or multi-bed) and propagation polarity (upward or downward). For each stratigraphic interface FracAbut provides information on fractures (type, number) and interface sensitivity (coupling strength).First, we apply FracAbut on synthetic case studies, then, on naturally fractured and stratified carbonates in Berat, Albania. Using both 1D scan-line and 2D outcrop photograph, we show that i) a mechanical interface can have different coupling above and below based on propagation polarity, ii) FracAbut results can give useful insight on fracture transmissivity, iii) FracAbut is fast and efficient to quantify fracture patterns and classify mechanical interface impact; iv) they are no relation between bed thickness and fracture propagation.

Stable and Fast Ion Transport Electrolyte Interfaces Modified with Novel Fluorine- and Nitrogen-Containing Solvents for Ni-Rich Cathode Materials.

Ternary nickel-rich layered oxide LiNi0.8Co0.1Mn0.1O2 (NCM811) is recognized as a cathode material with a promising future, attributed to its high energy density. However, the pulverization of cathode particles, structural collapse, and electrolyte decomposition are closely associated with the fragile cathode-electrolyte interphases (CEI), which seriously affect the electrochemical performances of ternary high-nickel materials. In this paper, fluorine- and nitrogen-containing methyl-2-nitro-4-(trifluoromethyl)benzoate (MNTB) was selected, which was synergistically regulated with fluoroethylene carbonate (FEC) to generate a robust CEI film. The preferential decomposition of MNTB/FEC results in the formation of an inorganic-rich (Li3N, LiF, and Li2O) CEI film with uniformly dense and stable characteristics, which is conducive to the migration of Li+ and the stability of the NCM811 structure and enhances the cycling stability of the battery system. Simultaneously, MNTB effectively suppresses the adverse reaction associated with increased polarization caused by higher interface impedance due to conventional single FEC additives, further improving the rate capability of the battery. Moreover, MNTB/FEC can effectively eliminate HF, preventing its corrosion on the NCM811 cathode. Under the synergistic effect of MNTB/FEC, after 300 discharge cycles at a high cutoff voltage of 4.3 V and a current density of 1 C (2 mA cm-2), the discharge capacity of the NCM811||Li battery was 150.12 mA h g-1 with a capacity retention of 81.10%, while it was only 32.8% for the standard electrolyte (STD). The discharged capacity of the MNTB/FEC-containing battery was about 115.43 mA h g-1 at the high rate of 7 C, which was considerably higher than that of the STD (93.34 mA h g-1). In this study, the designed MNTB as a novel solvent synergistically regulated with FEC will contribute to the enhanced stability of NCM811 materials at high cutoff voltages and at the same time provide an effective modified strategy to enhance the stability of commercial electrodes.

Self‐adhesive and biocompatible dry electrodes with conformal contact to skin for epidermal electrophysiology

AbstractLong‐term biopotential monitoring requires high‐performance biocompatible wearable dry electrodes. But currently, it is challenging to establish a form‐preserving fit with the skin, resulting in high interface impedance and motion artifacts. This research aims to present an innovative solution using an all‐green organic dry electrode that eliminates the aforementioned challenges. The dry electrode is prepared by introducing biocompatible maltitol into the chosen conductive polymer, poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate). Thanks to the secondary doping and plasticizer effect of maltitol, the dry electrode exhibits good stretchability (62%), strong self‐adhesion (0.46 N/cm), high conductivity (102 S/cm), and low Young's modulus (7 MPa). It can always form a conformal contact with the skin even during body movements. Together with good electrical properties, the electrode enables a lower skin contact impedance compared to the current standard Ag/AgCl gel electrode. Consequently, the application of this dry electrode in bioelectrical signal measurement (electromyography, electrocardiography, electroencephalography) and long‐term biopotential monitoring was successfully demonstrated.

Terahertz absorption properties of different graphene layers based on the Salisbury effect

Terahertz (THz) absorbers based on the Salisbury screen have attracted significant attention for high absorption performance and simple structure. Graphene is suitable for high-performance THz absorbers due to its extraordinary electronic and optical properties. The study of graphene THz absorbers based on Salisbury screens has attracted great interest, where the number of graphene layers significantly affects the interface impedance matching and absorption efficiency. In this work, we proposed a sandwich-structured graphene/Polyimide (PI) /Au THz absorber based on the Salisbury screen. The results show that the absorption peak tended to increase and then decrease with the increase in the number of graphene layers. The simulation demonstrates that the real and imaginary parts of the relative impedance of the 3-5 layer graphene absorber were 1.02 and 0.01, which achieved a better impedance matching with the free space. Meanwhile, the measured sheet resistance value of 426 Ω/sq was closest to the free-space impedance value of 377 Ω, consistent with the simulation results. The corresponding absorption reached a maximum value of 98.7% at 0.82 THz (measured). In addition, the absorption peak decreased from 98.7% to 86.7% as the angle of incidence increased from 0° to 60°. This demonstrates the advantage of wide-angle absorption. The proposed device is suitable for applications in electromagnetic shielding and imaging, while the suggested method can be employed for the fabrication of other graphene-based devices.

An Elastomeric Lithium-Conducting Interlayer for High-Performance LATP-Based Lithium Metal Batteries.

In response to the critical challenges of interfacial impedance and volumetric changes inLi(1+x)AlxTi(2‑x)(PO4)3 (LATP)-based lithium metal batteries, an elastomeric lithium-conducting interlayer fabricates from fluorinated hydrogenated nitrile butadiene rubber (F-HNBR) matrix is introduced herein. Owing tothe vulcanization, vapor-phase fluorination, and plasticization processes, the lithium-conducting interlayer exhibits a high elasticity of 423%, exceptional fatigue resistance (10000 compression cycles), superior ionic conductivity of 6.3×10-4 S cm-1, and favorable lithiophilicity, rendering it an ideal buffer layer. By integrating the F-HNBR interlayer, the LATP-based lithium symmetric cells demonstrate an extended cycle life of up to 1600h at 0.1mA cm-2 and can also endure deep charge/discharge cycles (0.5 mAh cm-2) for the same duration. Furthermore, the corresponding lithium metal full cells achieve 500 cycles at 0.5 C with 98.3% capacity retention and enable a high-mass-loading cathode of 11.1mg cm-2 to operate at room temperature.

In Situ Structural Densification of Hydrogel Network and Its Interface with Electrodes for High-Performance Multimodal Artificial Skin.

The multisensory responsiveness of hydrogels positions them as promising candidates for artificial skin, whereas the mismatch of modulus between soft hydrogels and hard electrodes as well as the poor adhesion and conductance at the interface greatly impairs the stability of electronics devices. Herein, we propose an in situ postprocessing approach utilizing electrochemical reactions between metals (Zn, etc.) and hydrogels to synergistically achieve strong adhesion of the hydrogel-electrode interface, low interfacial impedance, and local strain isolation due to the structural densification of the hydrogel network. The mechanism is that Zn electrochemically oxidizes to Zn2+ and injects into the hydrogel, gradually forming a mechanically interlocked structure, Zn2+-polymer dual-helix structural nodes, and a high-modulus ZnO from the surface to the interior. Compared to untreated samples, the treated sample displays 8.7 times increased interfacial adhesion energy between the hydrogel and electrode (87 J/m2), 95% decreased interfacial impedance (218.8 Ω), and a high-strain isolation efficiency (εtotal/εisolation > 400). Akin to human skin, the prepared sensor demonstrates multimodal sensing capabilities, encompassing highly sensitive strain perception and simultaneous perception of temperature, humidity, and oxygen content unaffected by strain interference. This easy on-chip preparation of hydrogel-based multimodal sensor array shows great potential for health and environment monitoring as artificial skin.

In Situ Fabrication of High Ionic and Electronic Conductivity Interlayers Enabling Long-Life Garnet-Based Solid-State Lithium Batteries.

Garnet-type Li6.75La3Zr1.75Ta0.25O12 (LLZTO) is a promising solid-state electrolyte (SSE) because of its fast ionic conduction and notable chemical/electrochemical stability toward the lithium (Li) metal. However, poor interface wettability and large interface resistance between LLZTO and Li anode greatly restrict its practical applications. In this work, we develop an in situ chemical conversion strategy to construct a highly conductive Li2S@C layer on the surface of LLZTO, enabling improved interfacial wettability between LLZTO and the Li anode. The Li/Li2S@C-LLZTO-Li2S@C/Li symmetric cell has a low interface impedance of 78.5 Ω cm2, much lower than the 970 Ω cm2 of a Li/LLZTO/Li cell. Moreover, the Li/Li2S@C-LLZTO-Li2S@C/Li cell exhibits a high critical current density of 1.4 mA cm-2 and an ultralong stability of 3000 h at 0.1 mA cm-2. When used in a LiFePO4 battery, the Li/Li2S@C-LLZTO/LiFePO4 battery exhibits a high initial discharge capacity of 150.8 mA h g-1 at 0.2 C without lithium storage capacity attenuation during 200 cycles. This work provides a novel and feasible strategy to address interface issues of SSEs and achieve lithium-dendrite-free solid-state batteries.

In-situ coating strategy to synthesize ultra-soft sulfide solid-state electrolytes for dendrite-free lithium metal batteries

High energy density lithium metal batteries play a crucial role in future energy storage. High ionic conductivity argyrodite-type Li5.5PS4.5Cl1.5 is a promising candidate for future lithium metal all-solid-state batteries. However, under cold pressing conditions, the combination of high electronic conductivity and high porosity significantly accelerates the growth of lithium dendrites, resulting in low capacity and a short lifespan. In this study, we combined a simple wet ball milling and in-situ polymerization process to fabricate a polyvinylene carbonate-coated sulfide composite solid electrolyte. The ultra-soft particle, when cold-pressed without binders, completed a tightly packed and void-free internal structure. This electrolyte, combined with a stable LiF-rich interface layer on lithium metal, held a higher critical current density of 2.0 mA cm−2 than 0.65 mA cm−2 of uncoated argyrodite and a 2000-hour stable cycle at 0.5 mA cm−2 in lithium symmetric cells. The unique coating structure also mitigated the chemomechanical failure between electrolyte and electrode, preventing the rapid increase of interface impedance and achieving a high initial capacity of 173.5 mAh g−1 without a short circuit for 300 cycles in LiNi0.6Co0.2Mn0.2O2//Li cells.

The impact of magnesium content on lithium-magnesium alloy electrode performance with argyrodite solid electrolyte

Solid-state lithium-based batteries offer higher energy density than their Li-ion counterparts. Yet they are limited in terms of negative electrode discharge performance and require high stack pressure during operation. To circumvent these issues, we propose the use of lithium-rich magnesium alloys as suitable negative electrodes in combination with Li6PS5Cl solid-state electrolyte. We synthesise and characterise lithium-rich magnesium alloys, quantifying the changes in mechanical properties, transport, and surface chemistry that impact electrochemical performance. Increases in hardness, stiffness, adhesion, and resistance to creep are quantified by nanoindentation as a function of magnesium content. A decrease in diffusivity is quantified with 6Li pulsed field gradient nuclear magnetic resonance, and only a small increase in interfacial impedance due to the presence of magnesium is identified by electrochemical impedance spectroscopy which is correlated with x-ray photoelectron spectroscopy. The addition of magnesium aids contact retention on discharge, but this must be balanced against a decrease in lithium diffusivity. We demonstrate via electrochemical testing of symmetric cells at 2.5 MPa and 30∘C that 1% magnesium content in the alloy increases the stripping capacity compared to both pure lithium and higher magnesium content alloys by balancing these effects.

Temperature regulated Fe3Si@SiC@carbon core-shell structure with high-performance microwave absorption

Developing high-performance microwave absorbing materials (MAMs) to address the electromagnetic wave pollution is still a huge challenge. Multi-interface core-shell structure with magnetic and dielectric loss components have been attracting extensive attention as MAMs for the enhanced interfacial polarization and impedance matching. In this work, magnetic loss core and dielectric loss bi-shell structure Fe3Si@SiC@C (FSC) composite was synthesized through hydrothermal, self-polymerizing coating and high temperature thermolysis. The thermal treatment temperature has a great effect on the morphology structure and electromagnetic properties of FSC. The results indicated that the FSC exhibited an effective absorption bandwidth (EAB) of 4.24 GHz at a thickness of 1.4 mm, and an EAB of 12.4 GHz with the absorber thickness varied from 1 mm to 3 mm. Furthermore, the microwave attenuation mechanism of the FSC composite were investigated in detail. The integration of magnetic core with multiple dielectric shells provides a design deliberation and reference for further high-performance MAMs fabrication.

Exploring the impact of synergistic dual-additive electrolytes on 5 V-class LiNi0·5Mn1·5O4 cathodes

Tris (trimethylsilyl) phosphate (TMSP) and tris(2,2,2-trifluoroethyl) phosphate (TTFP) was added to carbonate solvent-based electrolytes as dual-additives to enhance the performance of LiNi0·5Mn1·5O4 (LNMO). The X-ray photoelectron spectroscopy results revealed that both TMSP with high oxidation ability and TTFP with high oxidation resistance participated in the formation of cathode–electrolyte interphase (CEI) films. Electrochemical impedance spectroscopy confirmed that the constructed CEI films had excellent electronic insulation and ionic conductivity, reducing the interfacial impedance of the LNMO electrode, and improving the electrochemical performance of LNMO/Li half-cells and LNMO/Li4Ti5O12 full-cells. As measured by the nuclear magnetic resonance, the incorporation of TMSP and TTFP significantly reduced the HF content in the electrolytes. Therefore, both LNMO/Li half-cells (500 cycles with 95.7% capacity retention) and LNMO/Li4Ti5O12 full-cells (200 cycles with 79.9% capacity retention) displayed higher cycling stabilities at 5 C owing to the synergistic effect of TMSP and TTFP. In comparison, capacity retentions of ∼76.5% after 500 cycles and ∼37.2% after 200 cycles were respectively achieved for the LNMO/Li half-cells and LNMO/Li4Ti5O12 full-cells with the standard electrolyte at 5 C. This study provides strong evidence that additive combinations can improve the electrochemical performance of high-energy and high-voltage cathode materials.