Intact Knee Research Articles

Establishment of 3D finite element model of meniscus and its mechanical analysis

To establish a 3D finite element model of normal knee joint involved its meniscus, which can be used to simulate the anatomical morphology and characteristics of human knee joint, to verify the validity of the model by preliminary FEA mechanical analysis, and explain partially biomechanical mechanisms of meniscus. CT and MRI data were harvested by scanning the knee joint of a healthy male volunteer, and then these data were imported into Mimics 10.01 software and Geomagic Studio software to constructed the 3D models of tissue structures of knee joint. These models were combined to constructed the 3D model of intact knee joint and meshed in ANSA software. Therefore the finite element model of intact knee joint was established. Finally, after the definitionof its material behavior, boundary conditions and loading. The finite element model of knee joint was analyzed and verified using ANSYS software. Meanwhile The biomechanical properties of meniscus were analyzed. The complete knee finite element model composed of bone, meniscus, articular cartilage, and major ligaments was established. It could effectively simulate the anatomical morphology and characteristics of knee joint and its meniscus. The contact area of medial meniscus was 771.05 mm2, while the contact area of lateral meniscus was 634.31 mm2, and the ratio was 1.216. The stress distribution was uniform, but the stress of the medial meniscus was higher than that of the lateral meniscus, and the peak stress located in the posterior horn of the medial meniscus and the anterior horn of the lateral meniscus, respectively, and the peak stress value was 4.11 MPa. The maximum displacement of the meniscus was located in body, and the displacement of the medial meniscus was more remarkable than that of the lateral meniscus, and the maximum displacement value is 0.33 mm. The obtained finite element analysis results corresponded to that reported in the literature, which mean the model's reliability. The established finite element model of knee joint are proved to be have validity, and is a useful model for finite element analysis of meniscus tear and menisectomy. The results of finite element analysis can explain partially biomechanical mechanisms of meniscus which can provide theoretical guidance for clinical treatment of meniscus injury.

Effects of the material properties of a focal knee articular prosthetic on the human knee joint using computational simulation

BackgroundLocalized cartilage defects are related to joint pain and reduced function to the development of osteoarthritis. The mechanical properties of the implant for treatment do influence its longevity. Therefore, we aimed to evaluate the effect of material properties' variations of anatomically shaped focal knee implants in the knee joint using numerical finite element analysis. MethodsComputational simulations were performed for different cases including an intact knee, a knee with a focal cartilage defect, and a knee fitted with a focal articular prosthetic having three distinct mechanical properties: cobalt–chromium, pyrolytic carbon, and polyethylene. Femoral cartilage, tibial cartilage, and menisci contact pressures were evaluated under the load. In addition, bone stress was evaluated to investigate the stress shielding effect. ResultsCompared with the intact model, the contact stress of the focal implant model was increased; on the femoral lateral cartilage by 14%, on medial and lateral tibial cartilages by nine percent and 10%, on medial and lateral menisci by 23% and 20%. In contrast, the focal implant model had no effect on the menisci but contact stress on the tibial cartilage increased compared with the intact model. The BioPoly model showed the lowest contact stress on femoral and tibial cartilages. Additionally, the cobalt–chromium model showed the lowest bone stress that improved the load-sharing effect. ConclusionsThe results suggested that implant material properties are an important parameter in the design of a focal implant. The polyethylene model potentially restored the intact knee contact mechanics and it reduced the risk of physiological damage to the articular cartilage.

Laxité du genou dans les lésions complexes antérolatérales par rapport aux lésions de la corne postérieure du ménisque médial dans les lésions du ligament croisé antérieur : étude cadavérique

IntroductionThere is considerable debate regarding the function of anterolateral knee structures, including the anterolateral ligament (ALL) and anterolateral capsule, as knee stabilizers in anterior cruciate ligament (ACL) injured knees. Medial meniscus posterior horn (MMPH) injuries have also been associated with increased knee laxity in ACL injured knees. The purpose of this cadaveric biomechanical study was to compare the effects of the anterolateral complex (ALC) injury and meniscectomy of MMPH on knee laxity in ACL injured knees. HypothesisALC injury would have a greater effect on internal rotational laxity in ACL-injured knee than meniscectomy of MMPH. Material and methodsMatched-pair 10 fresh-frozen cadaveric knees underwent biomechanical evaluation of knee laxity. After testing the intact knee and ACL sectioned knee (ACL−) in matched-pair 10 fresh-frozen cadaveric knees, two groups were established: an ALC sectioning (ACL−/ALC−) group (n=5) and a MMPH meniscectomy (ACL−/MMPH−) group (n=5). Knee laxity was measured in terms of internal-external rotation, anterior-posterior translation, and varus-valgus angulation for each condition at knee flexion angles of 0°, 30°, 60° and 90°. ResultsAfter the additional sectioning of the ALC (ACL−/ALC−), the mean internal rotation at 0°, 30°, 60° and 90° of knee flexion showed the greater internal rotation laxity compared than intact knee (p=0.020, 0.011, 0.005 and <0.001). It also significantly increased anterior translation from ACL− at 30° and 60° (p=.011 and .005). In contrast, additional meniscectomy of the MMPH (ACL−/MMPH−) significantly increased external rotation laxity compared to intact knee (p=0.021, 0.018 and 0.024) and ACL− (p=0.037, 0.011 and 0.025) at 30°, 60° and 90°. ACL−/MMPH− also resulted in significantly increased anterior translation from ACL− at 30°, 60° and 90° (p=0.004, 0.008 and 0.002). DiscussionIn conclusion, the anterolateral complex, which include the ALL and anterolateral capsule, may play an important role in stabilizing the knee against internal rotation and anterior translation, while the MMPH may contribute to resisting external rotation and anterior translation stability in ACL-injured knee. Level of evidenceII, Controlled laboratory study.

Knee laxity in anterolateral complex injuries versus medial meniscus posterior horn injuries in anterior cruciate ligament injured knees: A cadaveric study

IntroductionThere is considerable debate regarding the function of anterolateral knee structures, including the anterolateral ligament (ALL) and anterolateral capsule, as knee stabilizers in anterior cruciate ligament (ACL) injured knees. Medial meniscus posterior horn (MMPH) injuries have also been associated with increased knee laxity in ACL injured knees. The purpose of this cadaveric biomechanical study was to compare the effects of the anterolateral complex (ALC) injury and meniscectomy of MMPH on knee laxity in ACL injured knees. HypothesisALC injury would have a greater effect on internal rotational laxity in ACL-injured knee than meniscectomy of MMPH. Material and methodsMatched-pair 10 fresh-frozen cadaveric knees underwent biomechanical evaluation of knee laxity. After testing the intact knee and ACL sectioned knee (ACL-) in matched-pair 10 fresh-frozen cadaveric knees, two groups were established: an ALC sectioning (ACL-/ALC-) group (n=5) and a MMPH meniscectomy (ACL-/MMPH-) group (n=5). Knee laxity was measured in terms of internal-external rotation, anterior-posterior translation, and varus-valgus angulation for each condition at knee flexion angles of 0°, 30°, 60° and 90°. ResultsAfter the additional sectioning of the ALC (ACL-/ALC-), the mean internal rotation at 0°, 30°, 60° and 90° of knee flexion showed the greater internal rotation laxity compared than intact knee (p=0.020, 0.011, 0.005 and<0.001). It also significantly increased anterior translation from ACL- at 30° and 60° (p=0.011 and 0.005). In contrast, additional meniscectomy of the MMPH (ACL-/MMPH-) significantly increased external rotation laxity compared to intact knee (p=0.021, 0.018 and 0.024) and ACL- (p=0.037, 0.011 and 0.025) at 30°, 60° and 90°. ACL-/MMPH- also resulted in significantly increased anterior translation from ACL- at 30°, 60° and 90° (p=0.004, 0.008 and 0.002). DiscussionIn conclusion, the anterolateral complex, which include the ALL and anterolateral capsule, may play an important role in stabilizing the knee against internal rotation and anterior translation, while the MMPH may contribute to resisting external rotation and anterior translation stability in ACL-injured knee. Level of evidenceII, controlled laboratory study.

Lower Tibial Tunnel Placement in Isolated Posterior Cruciate Ligament Reconstruction: Clinical Outcomes and Quantitative Radiological Analysis of the Killer Turn.

Background:The “killer turn” effect after posterior cruciate ligament (PCL) reconstruction is a problem that can lead to graft laxity or failure. Solutions for this situation are currently lacking.Purpose:To evaluate the clinical outcomes of a modified procedure for PCL reconstruction and quantify the killer turn using 3-dimensional (3D) computed tomography (CT).Study design:Case series; Level of evidence, 4.Methods:A total of 15 patients underwent modified PCL reconstruction with the tibial aperture below the center of the PCL footprint. Next, 2 virtual tibial tunnels with anatomic and proximal tibial apertures were created on 3D CT. All patients were assessed according to the Lysholm score, International Knee Documentation Committee (IKDC) Subjective Knee Evaluation Form, Tegner score, side-to-side difference (SSD) in tibial posterior translation using stress radiography, and 3D gait analysis.Results:The modified tibial tunnel showed 2 significantly gentler turns (superior, 109.87° ± 10.12°; inferior, 151.25° ± 9.07°) compared with those reconstructed with anatomic (91.33° ± 7.28°; P < .001 for both comparisons) and proximal (99° ± 7.92°; P = .023 and P < .001, respectively) tibial apertures. The distance from the footprint to the tibial aperture was 16.49 ± 3.73 mm. All patient-reported outcome scores (mean ± SD) improved from pre- to postoperatively: Lysholm score, from 46.4 ± 18.87 to 83.47 ± 10.54 (P < .001); Tegner score, from 2.47 ± 1.85 to 6.07 ± 1.58 (P < .001); IKDC sports activities score, from 19 ± 9.90 to 33.07 ± 5.35 (P < .001); and IKDC knee symptoms score, from 17.87 ± 6.31 to 25.67 ± 3.66 (P < .001). The mean SSD improved from 9.15 ± 2.27 mm preoperatively to 4.20 ± 2.31 mm postoperatively (P < .001). The reconstructed knee showed significantly more adduction (by 1.642°), less flexion (by 1.285°), and more lateral translation (by 0.279 mm) than that of the intact knee (P < .001 for all).Conclusion:Lowering the tibial aperture during PCL reconstruction reduced the killer turn, and the clinical outcomes remained satisfactory. However, SSD and clinical outcomes were similar to those of previously described techniques using an anatomic tibial tunnel.

Stress response envelopes of intact tibiofemoral joint and knee osteoarthritis.

The purpose of this study was to determine stress envelopes for an intact tibiofemoral joint and to study how they vary with knee loading, external-internal rotation, varus-valgus rotation and cartilage degradation (osteoarthritis) using the finite element method. The envelopes were presented in terms of knee flexion angle. The maximum von Mises stress for all tibiofemoral joint components increased with increasing the axial compressive force magnitude. Menisci exhibited the highest magnitude of maximum von Mises stress as compared to the femoral and tibial cartilages. In a range of flexion angles between 0° and 100°, the medial meniscus exhibited the highest maximum von Mises stress than the lateral meniscus and the stress in medial meniscus tended to increase with increasing the flexion angle. External-internal and varus-valgus rotations changed the stress distribution: higher stress on lateral compartment but lower stress on medial compartment, and conversely. The internal rotation provided more extreme effect than the external rotation. For the knee osteoarthritis, cartilage degradation (early stage) caused maximum von Mises stress to increase on the intact menisci revealing that knee osteoarthritis could also cause meniscal tear. The late osteoarthritis caused the maximum von Mises stress to increase on the calcified cartilage and subchondral bone.

Comparing the Kinematics of the Lower Limb Joints in Jump-Landing Maneuver Among Soccer Players With and Without Histories of Anterior Cruciate Ligament Reconstruction

Background: Jumping and landing are common activities in soccer, i.e., associated with Anterior Cruciate Ligament (ACL) injuries in the players, especially when experiencing fatigue. The current study aimed to compare the kinematics of the lower limb joints in jump-landing maneuver among soccer players with and without a history of anterior cruciate ligament reconstruction. Methods: Among active soccer players in the provincial league level in Hamedan Province, Iran, 12 individuals with the intact knee (control group), and 12 individuals with 6 to 24 months post anterior cruciate ligament reconstruction (experimental group) were selected by convivence sampling method as the study participants. During the jump-landing task, the range of motion and the joints' angle at the contact instance were measured before and after performing plyometric fatigue protocol using the Vicon motion capture system. Multivariate Analysis of Variance (MANOVA) at a significance level of P&lt;0.05 was used for intergroup comparisons. Results: Plyometric fatigue did not affect most of the kinematic variables before and after fatigue experience. Besides, only the hip range of motion revealed a significant difference between the study groups (P=0.38). Conclusion: Fatigue had more effect on some variables in individuals with ACL reconstruction, including the left and right hips angles. Moreover, there was a significant difference in some variables between the study groups; the range of motion of the left hip, the contact angle of the right hip before fatigue experience, and the contact angle of the right and left hips after fatigue. In general, a proper rehabilitation program is recommended for athletes with ACL reconstruction to reduce the risk of recurrence of jumping movements in exercise.

Lateral Extra-Articular Tenodesis Reduces ACL Graft Force Under Multiplanar Torques Simulationg Pivot Shit

Objectives:Utilization of lateral extra-articular tenodesis (LET) in conjunction with anterior cruciate ligament reconstruction (ACLR) has increased in recent years, however, the biomechanical impact of LET, when performed with contemporary techniques, on both load sharing between the ACL graft and the LET and on knee kinematics is not completely clear. The purpose of this study was to quantify the effect of LET performed with ACLR, in the presence of a compromised anterolateral tissues, on (1) forces carried by the ACL graft and the LET and (2) knee kinematics, during simulated pivot shift.Methods:manipulator equipped with a six-axis force-torque sensor. The robot applied multiplanar torques simulating two types of pivot shift (PS) subluxing the lateral compartment at 15° and 30° of knee flexion. The following loading combinations were applied: (PS1) 8 Nm of valgus and 4 Nm of internal rotation torques; (PS2) 100 N compression force, 8 Nm valgus torque, 2 Nm internal rotation torque, and 30 N anterior force. Anteroposterior (AP) translation in the lateral compartment of the knee was recorded in the following states: ACL intact, sectioned, reconstructed and, finally, after sectioning the anterolateral ligament (ALL) and kaplan fibers and performing a LET. ACLR was performed utilizing a bone-patellar tendon-bone autograft, via medial parapatellar arthrotomy. LET was performed using a modified lemaire technique with a metal staple femoral fixation at 60° of flexion in neutral rotation. Resultant forces carried by the ACL graft and LET at the peak applied load in all tested conditions were determined utilizing the principle of superposition and serial sectioning.Results:Under both simulated pivot shift types and at both flexion angles the ACL force decreased with the addition of a LET, with the least force reduction of 39% for PS2 at 15° (p=0.01) and the most force reduction of 80% for PS1 at 30° (p<0.001). While decreasing ACL force, the LET carried at least 43% of the force carried by the ACL graft when tested without LET for PS2 at 15° and 91% of the force carried by the ACL graft at most, for PS1 at 30° (Table 1). For both combinations of multiplananr torques and at both flexion angles, the anterior tibial translation in the lateral compartment decreased for the ACLR+LET knee compared to the intact knee (5.3mm and 7.6mm decrease, for PS1 15° and 30° respectively, p<0.001; 4.4mm p=0.005 and 7.6mm p<0.001, for PS2 15° and 30°, respectively). (Figure 2).Conclusion:During a simulated pivot shift, LET shields the ACL graft from loading. This effect was greatest at 30° of flexion with an 80% drop in ACL graft force. While some shielding of load from the ACL graft can be beneficial, a more significant reduction in the load of the ACL graft may potentially be detrimental to the graft remodeling, maturation and function. The optimal load sharing pattern for improved clinical outcomes is not well understood and merit further investigation. In addition, LET also decreases anterior tibial translation in the lateral compartment to less than that of the intact knee, which represents overconstraint of the lateral compartment. These findings may support the purported “protective” effect of LET on the ACL graft and its important role in stabilizing the lateral compartment in the setting of combined ACL and anterolateral structures deficiency. The influence of overconstraint of the lateral compartment with LET warrants further biomechanical and clinical evaluation.Table 1.Mean loads carried by the ACL graft before and after the addition of a LET and loads carried by the LET, under both simulated pivot shift types at 15 ° and 30° of flexionMean ACL Graft Loads (n=7)Mean LET Loads (n=7)Without LETWith LETDifference% Drop*LET LoadRelative Load** PS1 15° 58±13 N20±23 N29±18 N49%31±15 N53% PS1 30° 54±13 N11±7 N44±12 N80%49±17 N91% PS2 15° 68±15 N41±20 N26±19 N39%29±17 N43% PS2 30° 71±15 N21±20 N50±14 N70%49±14 N70%PS1=8 Nm of valgus and 4 Nm of internal rotation torquesPS2=100 N compression, 8 Nm valgus, 2 Nm internal rotation, and 30 N anterior force*the percent of ACL graft force drop**The percent of load carried by LET relative to the load carried by ACL graft without LETFigure 1.Figure 2.

Knees with Smaller Posterior Tibial Slope And More Concave Medial Tibial Plateau Are At Higher Risk Of Isolated Meniscal Injuries

Objectives:Meniscal injuries are extremely common. Several anatomical features of the knee, including the tibial plateau morphology, have been shown to influence knee biomechanics and the risk of ligamentous injuries. Little is known, however, how these morphological features influence the risk of isolated meniscal injuries in the ACL intact knee. In the current study, we used MRI and 3D image analysis to investigate anatomical variables of knees in patients with and without isolated meniscus tears. We hypothesized that there are differences in slopes and concavity of the tibial plateau between patients with isolated meniscus tears and matched normal controls.Methods:65 subjects with first-instance isolated medial or lateral meniscal injuries requiring surgical fixation (Age: 15 +/- 2 years, BMI: 23.2 +/- 3.7 Kg/m2; 43% females) were matched to 65 subjects with normal knees and no prior injuries (Age: 15 +/- 2 years, BMI: 23.1 +/- 3.8 Kg/m2; 43% females) based on age, BMI and sex. Sagittal Proton Density SPACE MR images (preoperative for injured group) were used to measure the posterior slope of the medial (MTS) and lateral (LTS) tibial plateau, coronal slope of the tibial plateau (CTS), and the maximum depth of the medial tibia plateau (MTD, as a measure of medial tibial plateau concavity), following established techniques-Figure 1. Two-sample t-test was used to compare the quantified anatomical features between the cases and matched controls.Results:There were no differences in age (p = 0.999), sex distribution (p = 0.999) and BMI (p = 0.963) between the two cohorts. Compared to matched controls, patients with isolated meniscal tears had lower LTS (3.6 +/- 3.2 vs 5.6 +/- 3.0 degrees; p < 0.001), lower MTS (3.4 +/- 2.9 vs 4.9 +/- 2.5 degrees; p = 0.001) and deeper MTD (2.4 +/- 0.8 vs 1.5 +/- 0.8 mm; p < 0.001). There was no difference in CTS between the groups (3.6 +/- 1.6 vs 3.9 +/- 2.2 degrees; p = 0.300).Conclusion:This study suggests that subjects with isolated meniscus tear have a lower posterior tibial slope and a deeper MTD (more concave medial tibial plateau) than matched population who do not have a meniscus tear. This is contrary to what is known for ACL tears, where a higher posterior tibial slope and a shallower MTD have been associated with an increased risk of ACL tear. During load-bearing activities, in particular high impact movements such as jumping, increased tibial slope and decreased MTD have shown to result in greater anterior shear forces across the knee. In contrast, the less sloped and more concave plateau will experience lower shear forces but more compression, which could be detrimental to the meniscus. This study provides preliminary evidence suggesting a link between tibial plateau morphology and risk of isolated meniscal injuries. Further mechanistic studies are required to better understand the interaction between knee morphology, meniscal loading and subsequent risk of injury.Figure 1.

Restoration of normal knee kinematics with respect to tibial insert design in mobile bearing lateral unicompartmental arthroplasty using computational simulation.

AimsMobile-bearing unicompartmental knee arthroplasty (UKA) with a flat tibial plateau has not performed well in the lateral compartment, leading to a high rate of dislocation. For this reason, the Domed Lateral UKA with a biconcave bearing was developed. However, medial and lateral tibial plateaus have asymmetric anatomical geometries, with a slightly dished medial and a convex lateral plateau. Therefore, the aim of this study was to evaluate the extent at which the normal knee kinematics were restored with different tibial insert designs using computational simulation.MethodsWe developed three different tibial inserts having flat, conforming, and anatomy-mimetic superior surfaces, whereas the inferior surface in all was designed to be concave to prevent dislocation. Kinematics from four male subjects and one female subject were compared under deep knee bend activity.ResultsThe conforming design showed significantly different kinematics in femoral rollback and internal rotation compared to that of the intact knee. The flat design showed significantly different kinematics in femoral rotation during high flexion. The anatomy-mimetic design preserved normal knee kinematics in femoral rollback and internal rotation.ConclusionThe anatomy-mimetic design in lateral mobile UKA demonstrated restoration of normal knee kinematics. Such design may allow achievement of the long sought normal knee characteristics post-lateral mobile UKA. However, further in vivo and clinical studies are required to determine whether this design can truly achieve a more normal feeling of the knee and improved patient satisfaction.Cite this article: Bone Joint Res 2020;9(7):421–428.

The effect of anterolateral ligament reconstruction on knee constraint: A computer model-based simulation study

BackgroundTo determine the influence of anterolateral ligament reconstruction (ALLR) on knee constraint through the analysis of knee abduction (valgus) moment when the knee is subjected to external translational (anterior) or rotational (internal) loads. MethodsA knee computer model simulated from a three-dimensional computed tomography scan of healthy male was implemented for this study. Three groups were designed: (1) intact knee, (2) combined Anterior Cruciate Ligament (ACL) and Antero-Lateral Complex (ALC) deficient knee, and (3) combined ACL and Antero- lateral Ligament (ALL) reconstructed knee. The reconstructed knee group was subdivided into four groups according to attachment of reconstructed anterolateral ligament to the femoral epicondyle. Each group of simulated knees was placed at 0°, 10°, 20°, 30°, 40° and 50° of knee flexion. For each position an external anterior (drawer) 90-N force or a five-newton meter internal rotation moment was applied to the tibia. The interaction effect between the group of knees and knee flexion angle (0–50°) on knee kinematics and knee abduction moment under external loads was tested. ResultsWhen reconstructed knees were subjected to a 90-N anterior force or a five-newton meter internal rotation moment there was significant reduction in anterior translation and internal rotation compared with deficient knees. Only the ALLR procedure using posterior and proximal femoral attachment sites for graft fixation combined with ACL reconstruction allowed similar mechanical behavior to that observed in the intact knee. ConclusionsCombined ACL and ALLR using a minimally invasive method in an anatomically reproducible manner prevents excessive anterior translation and internal rotation. Using postero-proximal femoral attachment tunnel for reconstruction of ALL does not produce overconstraint of the lateral tibiofemoral compartment.

Imaging Approaches for Accurate Determination of the Quadriceps Angle.

ObjectivesA retrospective study was conducted using magnetic resonance image (MRI) and a full‐length standing scanogram (FLSS) to measure the quadriceps angle (Q‐angle) while avoiding soft tissue interference.MethodsTwo steps were retrospectively carried out in two case series. The first step involved using MRI to define the standardized patellar center (PC) and the tibial tubercle (TT) on the frontal plane of the MRI in one group of 60 consecutive patients (from July 2016 to December 2016, 29 men and 31 women, average of 46 years). The next step was transferring the location of the standardized PC and the TT from the MRI to the FLSS in another group of 100 consecutive patients (from April 2009 to March 2014, 50 men and 50 women, average of 36 years). The pelvis and intact femur, knee, and tibia were used to determine the Q‐angle on the FLSS.ResultsThe standardized PC was positioned 42% from the lateral end of femur trans‐epicondylar line. The TT was 2 cm distal to the tibial articular surface and 37% from the lateral end of tibial width. The average Q‐angle was 9.5° in 100 patients (8.8° in 50 men and 10.1° in 50 women, P = 0.02). The average femoral length was 42.9 cm in 100 patients (44.7 cm in 50 men and 41.1 cm in 50 women, P < 0.001). Women and men had similar pelvic width (27.9 vs 27.8 cm, P = 0.89).ConclusionUsing the FLSS may help to accurately determine the Q‐angle. Men and women have similar pelvic width. A larger Q‐angle in women may be mainly due to the shorter femur.

The medial ligaments and the ACL restrain anteromedial laxity of the knee

PurposeThe purpose of this study was to determine the contribution of each of the ACL and medial ligament structures in resisting anteromedial rotatory instability (AMRI) loads applied in vitro.MethodsTwelve knees were tested using a robotic system. It imposed loads simulating clinical laxity tests at 0° to 90° flexion: ±90 N anterior–posterior force, ±8 Nm varus–valgus moment, and ±5 Nm internal–external rotation, and the tibial displacements were measured in the intact knee. The ACL and individual medial structures—retinaculum, superficial and deep medial collateral ligament (sMCL and dMCL), and posteromedial capsule with oblique ligament (POL + PMC)—were sectioned sequentially. The tibial displacements were reapplied after each cut and the reduced loads required allowed the contribution of each structure to be calculated.ResultsFor anterior translation, the ACL was the primary restraint, resisting 63–77% of the drawer force across 0° to 90°, the sMCL contributing 4–7%. For posterior translation, the POL + PMC contributed 10% of the restraint in extension; other structures were not significant. For valgus load, the sMCL was the primary restraint (40–54%) across 0° to 90°, the dMCL 12%, and POL + PMC 16% in extension. For external rotation, the dMCL resisted 23–13% across 0° to 90°, the sMCL 13–22%, and the ACL 6–9%.ConclusionThe dMCL is the largest medial restraint to tibial external rotation in extension. Therefore, following a combined ACL + MCL injury, AMRI may persist if there is inadequate healing of both the sMCL and dMCL, and MCL deficiency increases the risk of ACL graft failure.

Magnetic resonance imaging of human knee joint functionality under variable compressive in-situ loading and axis alignment

Magnetic resonance imaging (MRI) under mechanical loading, commonly referred to as stress MRI, allows the evaluation of functional properties of intra- and periarticular tissues non-invasively beyond static assessment. Quantitative MRI can identify physiological and pathological responses to loading as indication of, potentially treatable, early degeneration and load transmission failure. Therefore, we have developed and validated an MRI-compatible pressure-controlled axial loading device to compress human knee specimens under variable loading intensity and axis deviation. Ten structurally intact human knee specimens (mean age 83.2 years) were studied on a 3.0T scanner (Achieva, Philips). Proton density-weighted fat-saturated turbo spin-echo and high-resolution 3D water selective 3D gradient-echo MRI scans were acquired sequentially at 10° joint flexion in seven configurations: unloaded and then at approximately half and full body weight loading in neutral, 10° varus and 10° valgus alignment, respectively. Following manual segmentation in both femorotibial compartments, cartilage thickness (ThC) was determined as well as meniscus extrusion (ExM). These measures were compared to computed tomography scans, histological grading (Mankin and Pauli scores), and biomechanical properties (Instantaneous Young's Modulus).Compartmental, regional and subregional changes in ThC and ExM were reflective of loading intensity and joint alignment, with the greatest changes observed in the medial compartment during varus and in the lateral compartment during valgus loading. These were not significantly associated with the histological tissue status or biomechanical properties.In conclusion, this study explores the physiological in-situ response of knee cartilage and meniscus, based on stress MRI, and as a function of loading intensity, joint alignment, histological tissue status, and biomechanical properties, as another step towards clinical implementation.

Biomechanical Evaluation of an All-Inside Posterior Medial Meniscal Root Repair Technique Via Suture Fixation to the Posterior Cruciate Ligament

To evaluate the tibiofemoral contact mechanics of an all-inside posterior medial meniscal root repair technique via suture fixation to the posterior cruciate ligament (PCL) and to compare with that of the intact knee and the knee with a root tear. Tibiofemoral contact mechanics were recorded in 8 human cadaveric knee specimens using pressure sensors. Each knee underwent 3 testing conditions related to the posterior medial meniscal root: (1) intact knee; (2) root tear; and (3) all-inside repair via suture fixation to the PCL. Knees were loaded with a 1000-N axial compressive force at 4 knee flexion angles (0°, 30°, 60°, 90°). Calculations were performed for contact area, mean contact pressure, and peak contact pressure. A generalized linear model with a Tukey adjusted least square means test was used to determine differences between testing conditions. Across all knee flexion angles, there was an overall mean 26.3% reduction in contact area with root tear (211.34 mm2 vs intact 286.64 mm2, P= .0002), and a 31.6% increase from root tear to repair (277.61 mm2, P= .0297). Across all knee flexion angles, there was an overall mean 24.3% increase in contact pressure with root tear (1849.12 N/mm2 vs. intact 1487.52 N/mm2, P < .0001), and a 31.1% decrease from root tear to repair (1410.7 N/mm2, P= .0037). Across all knee flexion angles, there was an overall mean 10.6% increase in peak contact pressure with root tear (4083.55 N/mm2 vs. intact 3693.68 N/mm2, P < .0001), and a 12.4% decrease from root tear to repair (3632.13 N/mm2, P= .531). In most testing conditions and with overall averaging across knee flexion angles, the all-inside posterior medial meniscal root repair with suture fixation to the adjacent PCL fibers restored contact area (from 26.3% reduction with root tear to 31.6% increase with repair), contact pressures (from 24.3% increase with root tear to 31.1% decrease with repair), and peak contact pressures (from 10.6% increase with root tear to 12.4% decrease with repair) to that of the intact knee This may be a future potential technique to limit complications associated with the traditional transtibial pull-out method of repair. This technique may provide a posterior medial meniscal root repair construct that restores most tibiofemoral contact mechanics and offers theoretical benefits of technical ease and potential for an acceptable, less "anatomic" repair location.

The Popliteus Bypass provides superior biomechanical properties compared to the Larson technique in the reconstruction of combined posterolateral corner and posterior cruciate ligament injury

This study aimed to compare the biomechanical properties of the popliteus bypass against the Larson technique for the reconstruction of a combined posterolateral corner and posterior cruciate ligament injury. In 18 human cadaver knees, the kinematics for 134N posterior loads, 10Nm varus loads, and 5Nm external rotational loads in 0°, 20°, 30°, 60,° and 90° of knee flexion were measured using a robotic and optical tracking system. The (1) posterior cruciate ligament, (2) meniscofibular/-tibial fibers, (3) popliteofibular ligament (PFL), (4) popliteotibial fascicle, (5) popliteus tendon, and (6) lateral collateral ligament were cut, and the measurements were repeated. The knees underwent posterior cruciate ligament reconstruction, and were randomized into two groups. Group PB (Popliteus Bypass; n = 9) underwent a lateral collateral ligament and popliteus bypass reconstruction and was compared to Group FS (Fibular Sling; n = 9) which underwent the Larson technique. Varus angulation, posterior translation, and external rotation increased after dissection (p < 0.01). The varus angulation was effectively reduced in both groups and did not significantly differ from the intact knee. No significant differences were found between the groups. Posterior translation was reduced by both techniques (p < 0.01), but none of the groups had restored stability to the intact state (p < 0.02), with the exception of group PB at 0°. No significant differences were found between the two groups. The two techniques revealed major differences in their abilities to reduce external rotational instability. Group PB had less external rotational instability compared to Group FS (p < 0.03). Only Group PB had restored rotational instability compared to the state of the intact knee (p < 0.04) at all degrees of flexion. The popliteus bypass for posterolateral reconstruction has superior biomechanical properties related to external rotational stability compared to the Larson technique. Therefore, the popliteus bypass may have a positive influence on the clinical outcome. This needs to be proven through clinical trials.

Comparative Biomechanical Study Between Minimally Invasive Popliteus and LCL Reconstruction Versus LaPrade Technique

Background:Many aspects of the posterolateral corner (PLC) of the knee have been extensively studied within the past 20 years. Quantitative anatomic and biomechanical studies have demonstrated the importance of the 3 static stabilizers of the lateral side of the knee: the fibular collateral ligament, the popliteus tendon, and the popliteofibular ligament. There are various methods of reconstruction. However, currently, there is no consensus on the preferred reconstruction technique for treating patients with chronic PLC injuries. We have developed a new reconstructive technique for PLC based on tibiofibular-based technique, similar to LaPrade, and this technique is less invasive than the previous techniques.Hypothesis:There is no difference between minimally invasive popliteus and LCL reconstruction and LaPrade’s method in restoring the posterolateral stability of kneesMethods:Six paired fresh-frozen cadaveric knees were assessed in the intact state and then dissected to simulate a grade III posterolateral knee injury. By using a “Blocked randomization”, each paired knee was randomized into 2 groups (1) reconstruction via LaPrade’s method, (2) minimally invasive popliteus and LCL reconstruction. Biomechanical testing using varus stress radiographs was performed to compare knee stability between 2 groups.Results:This study included six paired knees, three males and three females. The mean age of the cadaver was 70.8 years (range 57-85 years). No difference was found in the demographic data (sex distribution, lateral opening gap of intact knee and side-to-side difference of lateral opening gap of sectioned knee) between the 2 groups. The side-to-side difference in lateral joint opening on the varus stress radiographs significantly improved after PLC reconstruction in both groups (p <0.001, p <0.001), However, there were no differences between the 2 groups in side-to-side difference of lateral opening gap after reconstruction (Mean difference=-0.05 (95%CI, -0.46 to 0.36); p- value=0.039).Conclusion:Biomechanically, minimally invasive popliteus and LCL reconstruction is equivalent to LaPrade’s technique in restoring the stability of knees in case of grade III PLC injury. Additionally, this technique is less invasive than all traditional open technique of PLC reconstruction. The minimally invasive popliteus and LCL reconstruction technique may be a treatment option for grade III PLC injury. Keywords: posterolateral corner; ligament reconstruction; popliteus tendon; lateral collateral ligament; popliteofibular ligament; knee biomechanics; minimally invasive surgery

Single-bundle MCL reconstruction with anatomic single-bundle ACL reconstruction does not restore knee kinematics.

The purpose of this study was to evaluate and compare knee kinematics and kinetics following either single bundle, modified triangular or double-bundle reconstruction of the superficial medial collateral ligament (sMCL) with single bundle anatomic ACL reconstruction. Using a cadaveric model (n = 10), the knee kinematics and kinetics following three MCL reconstructions (single-bundle(SB), double-bundle(DB), modified triangular) with single bundle anatomic ACL reconstruction were compared with the intact and deficient knee state. The knees were tested under (1) an 89-N anterior tibial load, (2) 5 N-m internal and external rotational tibial torques, and (3) a 7 N-m valgus torque. Anatomic ACL reconstruction with SB MCL reconstruction was able to restore anterior tibial translation and external rotation to intact knee values but failed to the internal and valgus rotatory stability. Anatomical DB MCL reconstruction (with SB ACL reconstruction) and the modified triangular MCL reconstruction (with SB ACL reconstruction) restored allknee kinematics to the intact value. This study shows that clinical presentation with combined ACL and severe sMCL injury, single-bundle MCL with single-bundle ACL reconstruction does not restore knee kinematics. Anatomical double-bundle MCL reconstruction may produce slightly better biomechanical stability than the modified triangular MCL reconstruction, but the modified triangular reconstruction might be more clinically practical with the advantages of being less invasive and technically simpler while at the same time can restore a nearly normal knee joint.

The relationship between patellar lateralization diagnostic imaging markers and non-contact internal knee derangements

BackgroundTo investigate differences in the tibial tubercle-trochlear groove (TT-TG) and patellar tendon-posterior cruciate ligament (PT-PCL) distances in symptomatic patients with non-contact internal knee derangements (IKD) and symptomatic patients with internally intact knees (control).MethodsA retrospective review of MRI studies was completed by comparing 78 patients with meniscal and ligamentous derangements of the knee to 63 internally intact knees (age range, 13 to 50 years). MRI findings were reviewed independently by two board-certified radiologists to assess for agreement. TT-TG and PT-PCL distances were measured on proton density-weighted axial images by two independent observers blinded to the MRI and arthroscopic findings. Independent t tests were used to determine differences in TT-TG distance between the internal derangement and control groups. Chi-square tests were used to compare categorical variables for distributional equality between study groups.ResultsThe mean TT-TG distance averaged across the two raters in the IKD group was 11.5 mm (95% confidence interval [CI], 10.6–12.4), compared to 8.3 mm (95% CI, 7.6–9.0) in the control group (p < 0.001). The mean PT-PCL distance similarly averaged across both raters was 20.6 mm (95% CI, 19.7–21.5) for the IKD group compared to 18.2 mm (95% CI, 17.2–19.2) for the control group (p < 0.001). Among the IKD group, there were 51 meniscal tears, 12 cruciate ligament tears, and 15 tears with a combination of meniscal and cruciate findings. IKD was significantly correlated with greater TT-TG distance (p < 0.001) and greater PT-PCL distance (p < 0.003) when compared with control.ConclusionsIncreased TT-TG distances and PT-PCL distances are associated with both cartilaginous and ligamentous internal knee injuries in the present study, with TT-TG distances greater than the 12 mm representing a new threshold for concern.

A constrained-condylar fixed-bearing total knee arthroplasty is stabilised by the medial soft tissues

PurposeRevision constrained-condylar total knee arthroplasty (CCK-TKA) is often used to provide additional mechanical constraint after failure of a primary TKA. However, it is unknown how much this translates to a reliance on soft-tissue support. The aim of this study was therefore to compare the laxity of a native knee to the CCK-TKA implanted state and quantify how medial soft-tissues stabilise the knee following CCK-TKA.MethodsTen intact cadaveric knees were tested in a robotic system at 0°, 30°, 60° and 90° flexion with ± 90 N anterior–posterior force, ± 8 Nm varus-valgus and ± 5 Nm internal–external torques. A fixed-bearing CCK-TKA was implanted and the laxity tests were repeated with the soft tissues intact and after sequential cutting. The deep and superficial medial collateral ligaments (dMCL, sMCL) and posteromedial capsule (PMC) were sequentially transected and the percentage contributions of each structure to restraining the applied loads were calculated.ResultsImplanting a CCK-TKA did not alter anterior–posterior laxity from that of the original native knee, but it significantly decreased internal–external and varus-valgus rotational laxity (p < 0.05). Post CCK-TKA, the sMCL restrained 34% of the tibial displacing load in anterior drawer, 16% in internal rotation, 17% in external rotation and 53% in valgus, across the flexion angles tested. The dMCL restrained 11% of the valgus rotation moment.ConclusionsWith a fully-competent sMCL in-vitro, a fixed-bearing CCK-TKA knee provided more rotational constraint than the native knee. The robotic test data showed that both the soft-tissues and the semi-constrained implant restrained rotational knee laxity. Therefore, in clinical practice, a fixed-bearing CCK-TKA knee could be indicated for use in a knee with lax, less-competent medial soft tissues.Level of evidenceControlled laboratory study.