Insertion Loss Research Articles

Mode Heterogeneous Multimode Power Splitter Based on Cascaded Mode-Dependent Splitters and Converters

To the best of our knowledge, a novel concept of mode heterogeneity for the design of multimode devices is presented in this paper and applied to the design of scalable multimode power splitters. Based on a cascade of mode-dependent splitters and converters, we achieve beam splitting and mode conversion for four modes from TE0 to TE3 in the bandwidth from 1525 nm to 1560 nm. The measurements of the device at 1550 nm show excellent performance, with the insertion loss ranging from 0.16 dB to 0.63 dB, crosstalk all below −16.71 dB, and power uniformity between 0.026 dB and 0.168 dB.

A super-compact wideband bandpass filter using capacitor-loaded coupled lines

Abstract A wideband bandpass filter (BPF) using capacitor-loaded coupled lines is proposed with super-compact circuit size and very simple structure. By loading three lumped capacitors in parallel to three same pairs of coupled lines, three transmission poles and four transmission zeros can be achieved and they can be calculated by input admittance derivation. To verify the design, a wideband BPF prototype with center frequency at 1.34 GHz is fabricated, whose measured 3-dB fractional bandwidth is 98.5 % (0.68–2 GHz), in-band insertion loss is less than 0.5 dB, return loss is greater than 17.5 dB, and circuit size is only 0.24 λ g × 0.02 λ g (λ g: guided wavelength at the center frequency).

Design and simulation of a compact plasmonic photonic crystal fiber filter with wide band and high extinction ratio

In order to realize the performance optimization and function expansion of modern all-optical systems, this work presents a compact plasmonic photonic crystal fiber (PCF) filter, using finite element tool. The deposited gold and graphene layers within the elliptical pores interact with the transmitted light, creating surface plasmon resonance (SPR) effect that amplifies the energy difference between x- and y-polarized light greatly. The simulation results indicate that the structural parameters are configured with the cladding holes' diameter of 0.6 μm, the large-holes’ diameter of 1.2 μm, the inner small-holes’ diameter of 0.2 μm, the lattice constant of 2.0 μm, the elliptical holes' minor axis length of 0.45 μm, the elliptical holes' major axis length of 1.30 μm, the gold layer thickness of 50 nm, and the graphene layer thickness of 20 nm, the central wavelength of the proposed PCF filter is 1.56 μm. When the length of this PCF filter is 1 mm, a maximum extinction ratio (ER) of 133 dB, an operating bandwidth exceeding 800 nm, covering two common communication windows of 1.31 μm and 1.55 μm, as well as a low insertion loss (IL) of 0.59 dB can be achieved. What's more, the feasibility of fabricating the device is also examined. This filter with compactness, broadband and high-extinction demonstrates promising applications in optical communication, optical sensing, optical computing, and various other fields.

Automated fiber switch with path verification enabled by an AI-powered multi-task mobile robot

As the capacity of optical transport networks undergoes significant growth, there is an ongoing discussion on how to effectively leverage both spectral and spatial degrees of freedom to scale future network capacity. This paper presents an artificial intelligence (AI)-powered multi-task robot comprising a collaborative robotic arm and a mobile robotic base designed for optical network automation. The robot demonstrates the capability of direct fiber switching, establishing static fiber links that consume zero power and have minimal insertion loss from fiber connectors. As a precautionary measure before physically switching fiber cables, the robot performs path verification by detecting robot-driven events using real-time coherent receivers, aiming to avoid accidental unplugging. Additionally, the robot showcases its mobility by efficiently navigating between different network racks and rooms while executing various tasks. Implementing the automation of network operations using robots has the potential to reduce both capital and operational expenditures.

Femtosecond-laser-inscribed cladding waveguides in KTiOPO4 crystal for second-harmonic generation and Y-branch splitters

In this study, the fabrication of straight- and Y-branch-cladding waveguides in KTiOPO4 crystals using femtosecond laser-direct writing is described. The second-harmonic generation (SHG) of green light through the cladding waveguides was realized using a pulsed-wave pump at 1,064 nm. The guiding properties of straight-cladding waveguides fabricated by varying the laser-writing conditions were investigated. The minimum insertion loss was approximately 2.0 dB at 1,064 nm. Confocal micro-Raman spectroscopy was used to investigate the lattice micro-modifications. The maximum SHG conversion efficiency of the straight-cladding waveguide reached 31.4% with a maximum output power of 79.29 mW from an input power of 252.6 mW. The performances of the Y-branch splitters with splitting angles ranging from 0.5° to 2.6° were characterized at 1,064 nm, showing excellent properties, including symmetrical output ends and approximately equal splitting ratios. An SHG conversion efficiency of 13.4% and maximum output power of 33.63 mW were achieved in the Y-branch splitter with a splitting angle of 1.0°. These findings support potential applications in constructing compact-frequency converters by using femtosecond laser-written KTiOPO4 depressed-cladding waveguides.

Multiphysics simulations of a cylindrical waveguide optical switch using phase change materials on silicon

This work presents the design and multiphysics simulation of a cylindrical waveguide-based optical switch using germanium-antimony-tellurium (GST) as an active phase change material. The innovative cylindrical architecture is theoretically analyzed and evaluated at 1550 nm wavelength for telecommunication applications. The dispersion relation is derived analytically for the first time to model the optical switch, while finite element method (FEM) and finite difference time domain (FDTD) techniques are utilized to simulate the optical modes, light propagation, and phase change dynamics. The fundamental TE01 and HE11 modes are studied in detail, enabling switching between low-loss amorphous and high-loss crystalline GST phases. Increasing the GST thickness is found to increase absorption loss in the crystalline state but also slows down phase transition kinetics, reducing switching speeds. A 10 nm GST layer results in competitive performance metrics of 0.79 dB insertion loss, 13.47 dB extinction ratio, 30 nJ average power consumption, and 3.5 Mb/s bit rate. The combined optical, thermal, and electrical simulation provides comprehensive insights towards developing integrated non-volatile photonic switches and modulators utilizing phase change materials.

Compact supermode switch for photonic matrix processing.

A 2 × 2 switch based on differential effective thermo-optic (TO) coefficients of waveguide supermodes is proposed and experimentally demonstrated as a more compact alternative to Mach-Zehnder interferometer (MZI)-based switches used in coherent photonic matrix processing networks. The total waveguide width of the device is 1.335 μm. Using a novel, to the best of our knowledge, supermode coupler with a wideband 3-dB coupling ratio, the switch was engineered to have on-off extinction ratios (ERs) ranging from 24.1 to 38.9 dB for the two output ports over a 135 nm bandwidth. Insertion losses (ILs) of less than 0.3 and 0.4 dB over the 100 nm bandwidth were measured for bar and cross transmission, respectively. The waveguide width error tolerance is +/-30 nm. The proposed device has the potential to improve the scalability of a programmable coherent mesh for matrix processing by increasing the integration density without sacrificing the overall accuracy or limiting the operational wavelength range of the mesh.

Multimode near-infrared light-induced self-written optical waveguides for optical soldering

Connecting optical components in a highly precisely aligned manner that avoids significant losses due to misalignment is an important objective for future light-based high-speed data transmission technologies. We fabricated multimode light-induced self-written (LISW) optical waveguides using near-infrared (NIR) light for multimode optical component self-coupling. Multimode optical fibers were optically soldered with NIR light (≤ 1 mW) using this waveguide, with an insertion loss of only 0.69 dB observed when soldered at 0.6 mW.

Microstrip Quasi-Elliptic Absorptive Bandpass Filter with Ultra-Wide Reflectionless Range and Compact Size

Absorptive bandpass filters (ABPFs) are highly attractive in modern microwave communication systems due to their ability to internally absorb the harmful stopband RF-power reflections. This paper reports an approach to designing quasi-elliptic ABPFs with ultra-wide reflectionless range, enhanced selectivity, and compact size. The method is realized based on a fourth-order quasi-elliptic absorptive lowpass filter (ALPF) prototype with a simplified structure. This ALPF prototype exhibits both good impedance-matching over the whole normalized frequency domain and an adjustable transmission zero close to the passband. By applying an equivalent impedance transformer model, a coupled-line-based ABPF scheme is devised from the ALPF prototype, which eliminates conventional dispersive transmission line inverters, resulting in an ultra-wide reflectionless range and a compact size. Closed-form equations are derived to support the filter synthesis. A 2.45 GHz microstrip ABPF with 30% fractional bandwidth is designed for verification. The measured minimum in-band insertion loss is 0.83 dB and the reflectionless range of return loss better than 10 dB is from DC to 12.88 GHz. Both the upper and lower stopband suppression exceed 20 dB, with the upper stopband extending up to 6.80 GHz. The upper and lower out-of-band roll-off rates are 93.9 and 121.4 dB/GHz, respectively. The overall circuit size is 0.12 λg2.

Design and fabrication of a microstrip triplexer with wide flat channels for multi-band 5G applications.

In this paper, a new microstrip triplexer is designed to work at 2.5 GHz, 4.4 GHz and 6 GHz for mid-band 5G applications. All channels are flat with three low group delays (GDs) of 0.84 ns, 0.75 ns and 0.49 ns, respectively. Compared to the previously reported works, the proposed triplexer has the minimum group delay. The designed triplexer has 18.2%, 13.7%, 23.6% fractional bandwidths (FBW%) at 2.5 GHz, 4.4 GHz and 6 GHz, respectively. The obtained insertion losses (ILs) are low at all channels. These features are obtained without a noticeable increase in the overall size. A novel and simple resonator is used to design the proposed triplexer, which includes two pairs of coupled lines combined with a shunt stub. A perfect mathematical analysis is performed to find the resonator behavior and the layout optimization. The type of shunt stub is determined mathematically. Also, the smallness or largeness of some important physical dimensions is determined using the proposed mathematical analysis. Finally, the designed triplexer is fabricated and measured, where the measurement results verify the simulations.

Research on Low-Insertion-Loss Packaging Materials for DC-6 GHz Attenuation Chips

Research on Low-Insertion-Loss Packaging Materials for DC-6 GHz Attenuation Chips

Femtosecond laser direct writing large-area fiber Bragg grating based on diaphragm shaping

We propose and demonstrate a new method of direct writing large-area fiber Bragg grating by femtosecond laser through the coating. By adding an adjustable diaphragm before the focusing objective, we can precisely control the length of the refractive index modulation line along the femtosecond laser incident direction up to 29.1 µm. In combination with femtosecond laser scanning fabrication technology, a uniform refractive index modulation plane can be inscribed in the fiber in a single scanning. Based on the plane-by-plane inscription method, we have fabricated a high-quality high-reflectivity fiber Bragg grating and a chirped fiber Bragg grating on 20/400 double-clad fiber core. The reflectivity of both gratings is greater than 99%, and the insertion loss is as low as 0.165 dB and 0.162 dB, respectively. The thermal slope of chirped fiber Bragg grating without any refrigeration is 0.088 °C/W and there is no obvious temperature increase when using the water cooling. Therefore, the fabrication method of large-area fiber Bragg grating based on diaphragm shaping can efficiently fabricate high-quality fiber Bragg grating in the large core diameter fiber, which has an important application prospect in high-power all-fiber oscillators, especially all-fiber oscillators in special wavebands.

Omni-polarized Faraday isolator based on non-Hermitian Faraday system

Non-Hermitian systems have recently attracted significant attention in photonics due to the realization that the interplay between gain and loss can lead to entirely new and unexpected features. Here, we propose and demonstrate a non-Hermitian Faraday system capable of non-reciprocal omni-polarizer action at the exceptional point. Notably, both forward and backward propagating light with arbitrary polarization converge to the same polarization state. Leveraging the robustness and non-reciprocity of the non-Hermitian Faraday system, we realize an omni-polarized Faraday isolator that can effectively isolate any polarized light without the need for a polarizer at the incident port of backward propagation. Remarkably, under the given parameter configuration, the isolator achieves a maximum isolation ratio of approximately 100 dB and a minimum isolation ratio of around 45 dB for various polarized light, accompanied by near-zero insertion loss. Furthermore, our research reveals the remarkable tolerance of the non-Hermitian Faraday isolator to nonlinear effects. This unique characteristic allows us to harness nonlinear effects to achieve various optical functions, all while maintaining excellent isolation performance. The proposed non-Hermitian Faraday system paves the way for the realization of magnetically or optically switchable non-reciprocal devices.

Tailorable ITO thin films for tunable microwave photonic applications

Tunability is a fundamental prerequisite for functional devices and forms the backbone of reconfigurable microwave photonic (MWP) signal processors. In this paper, we explore the use of indium tin oxide (ITO) thin films, notable for their combination of optical transparency and electrical conductivity, to provide tunability for integrated MWP devices. We study the impacts of post-thermal annealing on the structural, electrical, and optical properties of ITO films. The annealed ITO microheater maintains a low total insertion loss of just 0.1 dB while facilitating the tunability of the microring across the entire free spectral range (FSR) using less than half the voltage required by its non-annealed counterpart. Furthermore, the post-annealed ITO film exhibits a 30% improvement in response time, enhancing its performance as an active voltage-controlled microheater. Leveraging this advantage, we employed the post-annealed device to demonstrate continuous tunable radio frequency (RF) phase shifts from 0–330° across a frequency range spanning 15 GHz to 40 GHz with only 5.58 mW of power. The flexibility in modifying the ITO thin film properties effectively bridges the gap between achieving low-loss and high-speed thermo-optic based microheaters.

Design and Fabrication of a Film Bulk Acoustic Wave Filter for 3.0 GHz-3.2 GHz S-Band.

Film bulk acoustic-wave resonators (FBARs) are widely utilized in the field of radio frequency (RF) filters due to their excellent performance, such as high operation frequency and high quality. In this paper, we present the design, fabrication, and characterization of an FBAR filter for the 3.0 GHz-3.2 GHz S-band. Using a scandium-doped aluminum nitride (Sc0.2Al0.8N) film, the filter is designed through a combined acoustic-electromagnetic simulation method, and the FBAR and filter are fabricated using an eight-step lithographic process. The measured FBAR presents an effective electromechanical coupling coefficient (keff2) value up to 13.3%, and the measured filter demonstrates a -3 dB bandwidth of 115 MHz (from 3.013 GHz to 3.128 GHz), a low insertion loss of -2.4 dB, and good out-of-band rejection of -30 dB. The measured 1 dB compression point of the fabricated filter is 30.5 dBm, and the first series resonator burns out first as the input power increases. This work paves the way for research on high-power RF filters in mobile communication.

A compact, low‐loss, and wide passband ratio substrate integrated waveguide triplexer based on complementary split ring resonators for multiband applications

SummaryIn this paper, a design of a substrate‐integrated waveguide (SIW) triplexer with improved low‐loss performance, passband ratio, and compactness based on the complementary split ring resonator (CSRR) structure is presented. The proposed triplexer operates at three passbands of 6, 8, and 10 GHz that correspond to the passband ratios of 1.33 and 1.67. By appropriately designing square CSRRs on the surface of the SIW structure, the low‐loss and compact resonator filters below the cut‐off frequency of the SIW at each operation frequency can be realized. The wide passband ratio is obtainable by adjusting the dimensions of the T‐junction. The measured results show the minimum insertion losses of 1.5, 1.4, and 1.9 dB at 6, 8, and 10 GHz, respectively. In addition, the minimum measured return losses are −9.33, −11.3, and −12.4 dB at the corresponding three passbands. The measured isolation between output ports is better than −17 dB in the frequency range from 5 to 11 GHz. The measured results agree well with simulations which are conducted by the CST Microwave Studio simulator. The proposed triplexer is designed on a cost‐effective RO4003C substrate with a compact size of 35 25 mm2

An S–K Band 6-Bit Digital Step Attenuator with Ultra Low Insertion Loss and RMS Amplitude Error in 0.25 μm GaAs p-HEMT Technology

An S–K Band 6-Bit Digital Step Attenuator with Ultra Low Insertion Loss and RMS Amplitude Error in 0.25 μm GaAs p-HEMT Technology

Accurate and non-contact measurement of volume percentages of oil-water fluids using microstrip sensors independent of the volume of sample using artificial neural network

Due to their moderate sensitivity, extremely cheap cost, ease of fabrication method, and, more crucially, the fact that they are non-invasive, planar microwave sensors have attracted a lot of interest from both industries and academics over the past years. These intriguing properties drive this field's research toward opening up a wide range of applications that go beyond oil and gas to include biological, material sensing, pollution monitoring, and other industrial uses. The main focus of this research is on the simulation and fabrication of a high-sensitivity, very small, and repeatable microwave sensor to measure volume fractions of oil and water in real-time. This sensor is designed by Ansys HFSS software and is made on the RT/Duroid 5880 (with εr =2.2, thickness = 0.787 mm, loss tangent of 0.0009). In a polylactic acid (PLA) box made using a 3D printer, oil and water with different volume percentages will be placed on the microwave sensor in non-contact conditions. To determine volume percentages independent of the volume of the samples, different samples were analyzed in volumes of 5 ml, 10 ml, and 15 ml. The developed sensor includes two passing bands, and when exposed to crude oil with varying amounts of water, the frequencies of these bands, their insertion loss, and their prominence in these frequencies change. Due to the non-linear variations in the insertion loss, frequency, and prominence value of the two passbands, the MLP neural network is used in this study over other approaches for identifying the objective parameter. The MLP neural network's output was the water volume percentage, and its inputs were variations in the frequency, insertion loss, and prominence of the two passbands in the transmission response. Thanks to microwave sensors and artificial neural networks, volume fractions could be detected with high accuracy, independent of the volume of samples. The suggested microwave sensor could be a highly effective way to measure volume percentages in the oil sector because of its high accuracy, compact size, simplicity of transportation, non-contact feature, etc.

Design and development of square stub loaded band pass filter with quality factor analysis

In this paper, a compact square stub-loaded band pass filter (BPF) is designed and investigated for quality factor improvement analysis. A detailed analysis has been presented to demonstrate the superior power handling capability of the proposed microstrip bandpass filter without any degradation in its electrical performance parameters. For this purpose, square-type stubs are incorporated in the proposed bandpass filter which reduced the maximum peak voltage and increased the high peak threshold, instead of using sharp edges. Also, an in-depth analysis of peak voltage with a center frequency of 2.1 and 4.2 have been carried out by considering some parameters like pressure and quality. The proposed bandpass filter shows minimum peak voltage of 1.61 V and 1.59 V across the frequency of 2.1 GHz and 4.2 GHz which covers the application of mobile and radio altimeters. The designed BPF shows the minimum heat generation of 0.29 and 0.89 per watt at the resonating frequencies of 2.1 and 4.2 GHz. Furthermore, the proposed bandpass filter presents an in-depth analysis of several characteristic parameters such as return loss, insertion loss, power loss, delay in group and phase, current distribution, H and E field distribution and maximum power loaded and unloaded quality factor.

Miniaturized IPD band pass filter with low insertion loss based on modified T‐section for 5G applications

AbstractA miniaturized bandpass filter (BPF) with low insertion loss based on a modified T‐section and a grounded transmission‐zero resonator is proposed. The novel T‐section consists of two resonators, which can achieve the bandpass performance with two transmission zeros (TZs) in the upper band. The grounded transmission‐zero resonator can generate an extra transmission zero in the lower band. Therefore, high frequency selectivity can be achieved by the above three transmission zeros near the passband. The proposed BPF can achieve an insertion loss of 0.8 dB and a return loss of 22 dB covering 3.3–4.2 GHz, and the upper‐stopband attenuation is better than 20 dB up to 12.5 GHz (3.3f0). The proposed BPF with a miniaturized size of 1.2 mm × 0.5 mm × 0.3 mm have been fabricated using Si‐based integrated passive devices (IPDs) technology and measured by on‐wafer probing. The simulated and measured results of the proposed BPF are in reasonably good agreement.