Inhalable Dust Exposure Research Articles

Wood dust exposure in the Danish furniture industry using conventional and passive monitors

A study of wood dust exposure at furniture factories in one county in Denmark was performed as a cross sectional study. Dust exposure was measured with personal passive dust monitors and calibrated against active sampling on filters. Measurements of 1685 workers were included in the exposure assessment. The passive dust monitor conversion models for equivalent concentrations of inhalable dust and total dust based on data from the present study were not significantly different from the original models. Therefore models based on all available data were used. The parameters of the distribution of equivalent concentration of inhalable dust were 0.94 mg/m3 (geometric mean) and 2.10 (geometric standard deviation). Compared with a national cross sectional study from 1988 the exposure level (geometric mean) was reduced by a factor 2.0. Inhalable dust exposure was about 50% higher than exposure measured by the Danish ‘total’ dust method.

Wood dust exposure in the Danish furniture industry using conventional and passive monitors

Abstract A study of wood dust exposure at furniture factories in one county in Denmark was performed as a cross sectional study. Dust exposure was measured with personal passive dust monitors and calibrated against active sampling on filters. Measurements of 1685 workers were included in the exposure assessment. The passive dust monitor conversion models for equivalent concentrations of inhalable dust and total dust based on data from the present study were not significantly different from the original models. Therefore models based on all available data were used. The parameters of the distribution of equivalent concentration of inhalable dust were 0.94 mg/m3 (geometric mean) and 2.10 (geometric standard deviation). Compared with a national cross sectional study from 1988 the exposure level (geometric mean) was reduced by a factor 2.0. Inhalable dust exposure was about 50% higher than exposure measured by the Danish ‘total’ dust method.

Determinants of inhalable dust exposure in the European carbon black manufacturing industry.

A large study to investigate the respiratory health effects of occupational exposure to carbon black in the European carbon black manufacturing industry commenced in 1987. During the study, a large amount of personal occupational exposure data was collected. This article describes the empirical models used to study the determinants of inhalable dust exposure, using data from 16 factories collected in the third and last cross-sectional phase of this study. Information on activities during the measurements was collected using short job category-specific questionnaires. In addition, questionnaires were completed by factory representatives on the implementation of control measures and changes in production process since the first cross-sectional phase. Mixed effects analyses of variance models were used to identify determinants of exposure, while taking into account the within- and between-worker (random) variance components. The results of these models show that, for any job category, factory is a strong predictor of exposure in this industry. These differences could not be explained entirely by factors such as age of the factory or the control measures implemented since the first phase of the study. Surprisingly, implementation of local exhaust ventilation systems had an effect that was counterintuitive; for example, in warehouses where local exhaust ventilation systems had been implemented, higher dust exposure levels were found compared to those where such control measures had not been installed since the first cross-sectional survey. Season appeared to have some effect on exposure for some job titles, with generally relatively low exposures being found in the summer. Finally, a number of activities were identified that caused higher levels of dust exposure, most notably "changing of filters" and "clean-up of carbon black spills."

Trends in levels of inhalable dust exposure, exceedance and overexposure in the European carbon black manufacturing industry

In an attempt to investigate the relationship between exposure to carbon black and respiratory morbidity, a study of the complete carbon black manufacturing industry in Western Europe was commissioned. As part of this study, a large number of personal inhalable (n=8015) dust exposure measurements was taken during three phases of data collection between 1987 and 1995. Repeated measurements on the same worker were taken in the last two phases, which enabled the estimation of the within- and between-worker components of variance. Simultaneously, the fixed effects of phase and factory were estimated using mixed-effects analysis of variance. The results show that the personal inhalable dust exposure has reduced significantly since the first phase of the study. In addition, the interaction term between phase and factory was significant in most job categories, confirming that the reduction of exposure was not equal across all factories. When all factories were considered together, the probability that the mean exposure of a randomly selected worker (overexposure) or the probability that the exposure on a randomly selected day for a randomly selected worker (exceedance) was higher than 3.5mg m(-3), was 10% or less for all job categories in the last phase. However, when the factories were considered separately, it appeared that the probability of overexposure or exceedance was in excess of 10% for the job categories 'Fitter/Welder', 'Warehouseman' and 'Site crew' for a number of factories. Therefore, even though exposure levels of inhalable dust have dropped considerably across the whole carbon black manufacturing industry in Western Europe, further reductions in exposure levels are required in these areas to make sure that the probability of overexposure and exceedance falls below a level of 10%.

Trends in levels of inhalable dust exposure, exceedance and overexposure in the European carbon black manufacturing industry

In an attempt to investigate the relationship between exposure to carbon black and respiratory morbidity, a study of the complete carbon black manufacturing industry in Western Europe was commissioned. As part of this study, a large number of personal inhalable (n=8015) dust exposure measurements was taken during three phases of data collection between 1987 and 1995. Repeated measurements on the same worker were taken in the last two phases, which enabled the estimation of the within- and between-worker components of variance. Simultaneously, the fixed effects of phase and factory were estimated using mixed-effects analysis of variance.The results show that the personal inhalable dust exposure has reduced significantly since the first phase of the study. In addition, the interaction term between phase and factory was significant in most job categories, confirming that the reduction of exposure was not equal across all factories.When all factories were considered together, the probability that the mean exposure of a randomly selected worker (overexposure) or the probability that the exposure on a randomly selected day for a randomly selected worker (exceedance) was higher than 3.5mg m−3, was 10% or less for all job categories in the last phase. However, when the factories were considered separately, it appeared that the probability of overexposure or exceedance was in excess of 10% for the job categories ‘Fitter/Welder’, ‘Warehouseman’ and ‘Site crew’ for a number of factories. Therefore, even though exposure levels of inhalable dust have dropped considerably across the whole carbon black manufacturing industry in Western Europe, further reductions in exposure levels are required in these areas to make sure that the probability of overexposure and exceedance falls below a level of 10%.

Respiratory symptoms and wheat flour exposure: a study of flour millers.

The objective of this study was to determine the prevalence of respiratory symptoms and their relationship to sensitization to wheat flour allergens and fungal amylase, in a group of workers from the UK flour milling industry. A cross-sectional study was used to evaluate symptoms, using a structured interview technique, and sensitization, using skin prick test findings, from 679 employees in flour milling and packing operations at 18 flour mills. A total of 147 workers (147/679, 22%) described upper respiratory tract symptoms of some kind. In the majority (139/147, 95%) these symptoms were of an occasional or transitory nature and were related to short-term exposures to high levels of dust. Three individuals (3/679, 0.4%) were identified whose symptoms were thought to be the result of allergy to wheat flour. The prevalence of positive skin prick tests to wheat flour allergens and to fungal amylase was 1.2% (8/678) and 0.9% (6/678), respectively. Measurements of total inhalable dust exposure for personnel exposed to flour dust were taken at 10 of the sites (116 samples). For production personnel the levels were typically between 1 and 10 mg/m3 (8-h time weighted average), with a median of 6.2 mg/m3. Hygiene operatives had appreciably higher exposure than production personnel, with a median of 18.7 mg/m3. Overall, 43% (50/116) of all samples exceeded 10 mg/m3 (8-h time weighted average). The findings suggest that the risk of sensitization to wheat flour allergens from current dust exposures in flour mills is very low. Wheat allergy was responsible in only a small proportion of the total who had respiratory symptoms. The principal causation of symptoms experienced by the workforce was considered to be a non-specific irritant effect related to short-term exposures to high levels of total inhalable dust.

Dust exposures in the wood processing industry.

Workers at four different woodworking processes--two logging sites, four sawmills, one major woodchipping operation, and five joineries situated in the state of New South Wales in Australia--were studied for personal inhalable dust exposures (N = 182). The geometric mean exposure at logging sites was 0.6 mg/m3 (N = 7), sawmills 1.6 mg/m3 (N = 93), woodchipping 1.9 mg/m3 (N = 9), and joineries 3.7 mg/m3 (N = 66). Overall, 62% of the exposures exceeded the current standards. Among joineries, 95% of the hardwood exposures and 35% of the softwood exposures were above the relevant standards. A majority of workers (approximately 90%) did not wear appropriate respirators approved for wood dust, while the ones who did wear them, used them on average less than 50% of the time. The significant determinants of personal wood dust exposures (n = 163) were found to be local exhaust ventilation, job title, use of handheld tools, cleaning method used, use of compressed air, and green or dry wood processed. Type of wood processed (softwood or hardwood) was not found to be statistically significant.

Exposure to captan in fruit growing.

This study characterized occupational exposure to pesticides in fruit growing in The Netherlands to assess determinants of exposure. Large-scale exposure surveys were carried out during application of pesticides and during reentry activities. Data on contamination inside the fruit growers' homes were obtained, and total potential exposure for the fruit grower and his family during the growing and harvesting season was estimated. Repeated measurements on the same subject were collected to study components of exposure variability. Relative contribution of the respiratory route and different skin sites to total exposure were assessed. Captan was used as a marker for exposure. Inhalable dust exposure was measured with a personal monitor and potential dermal exposure with skin pads and hand rinsing. Dislodgeable foliar residue was measured by taking leaf punches. For respiratory exposure and potential dermal exposure, differences were observed between several tasks. Workers were categorized according to tasks performed depending on the exposure measure(s) (e.g., hands, forehead, inhalable dust) considered relevant for a specific study purpose. In general, within-worker variability of all exposure measurements was larger than between-worker variability. Variability in dermal exposure on the same body location was small relative to variability between different body locations. Differences in total exposure, including exposure inside the home, between the fruit grower and the son were small. Exposure of the wife was two to three times lower than for the fruit grower and the son. As exposure per unit of time was in the same order of magnitude for different tasks, individual time spent on these tasks is crucial for estimating total potential exposure. Repeated measurements are necessary to estimate individual exposure accurately because of the large within-worker variability.

Exposure to Captan in Fruit Growing

This study characterized occupational exposure to pesticides in fruit growing in The Netherlands to assess determinants of exposure. Large-scale exposure surveys were carried out during application of pesticides and during reentry activities. Data on contamination inside the fruit growers' homes were obtained, and total potential exposure for the fruit grower and his family during the growing and harvesting season was estimated. Repeated measurements on the same subject were collected to study components of exposure variability. Relative contribution of the respiratory route and different skin sites to total exposure were assessed. Captan was used as a marker for exposure. Inhalable dust exposure was measured with a personal monitor and potential dermal exposure with skin pads and hand rinsing. Dislodgeable foliar residue was measured by taking leaf punches. For respiratory exposure and potential dermal exposure, differences were observed between several tasks. Workers were categorized according to tasks performed depending on the exposure measure(s) (e.g., hands, forehead, inhalable dust) considered relevant for a specific study purpose. In general, within-worker variability of all exposure measurements was larger than between-worker variability. Variability in dermal exposure on the same body location was small relative to variability between different body locations. Differences in total exposure, including exposure inside the home, between the fruit grower and the son were small. Exposure of the wife was two to three times lower than for the fruit grower and the son. As exposure per unit of time was in the same order of magnitude for different tasks, individual time spent on these tasks is crucial for estimating total potential exposure. Repeated measurements are necessary to estimate individual exposure accurately because of the large within-worker variability.

Exposure levels and determinants of inhalable dust exposure in bakeries

The study's objectives were to measure full-shift exposure to inhalable dust in bakeries and define the determinants of full-shift exposure. Inhalable dust was measured gravimetrically. Ninety-six bakery workers, employed in seven different bakeries, participated in the study. Two side-by-side full-shift inhalable dust samples were obtained from each study participant on a single occasion. Samples were collected on 18 days selected at random. During the entire sampling period, bakers were observed and information on 14 different tasks was recorded at 15 min intervals. Other production characteristics were also recorded for each sampling day. These task and production variables were used in statistical modelling to identify significant predictors of exposure. The mean full-shift inhalable dust exposure was 8.2 mg/m3 (range: 0.1–110 mg/m3). A regression model explained 79% of the variability in exposure. The model indicated that tasks such as weighing, pouring and operating dough-brakers and reversible sheeters increased the exposure, while packing, catching and decorating decreased the exposure. Bread and bun production lines were associated with increased full-shift inhalable dust exposure, while cake production and substitution of dusting with the use of divider oil were associated with decreased exposure. Production tasks and characteristics are strong predictors of personal full-shift exposures to flour dust among bakers; these can be altered to reduce exposure levels.

EXPOSURE LEVELS AND DETERMINANTS OF INHALABLE DUST EXPOSURE IN BAKERIES

The study's objectives were to measure full-shift exposure to inhalable dust in bakeries and define the determinants of full-shift exposure. Inhalable dust was measured gravimetrically. Ninety-six bakery workers, employed in seven different bakeries, participated in the study. Two side-by-side full-shift inhalable dust samples were obtained from each study participant on a single occasion. Samples were collected on 18 days selected at random. During the entire sampling period, bakers were observed and information on 14 different tasks was recorded at 15 min intervals. Other production characteristics were also recorded for each sampling day. These task and production variables were used in statistical modelling to identify significant predictors of exposure. The mean full-shift inhalable dust exposure was 8.2 mg/m3 (range: 0.1–1 10 mg/m3). A regression model explained 79% of the variability in exposure. The model indicated that tasks such as weighing, pouring and operating dough-brakers and reversible sheeters increased the exposure, while packing, catching and decorating decreased the exposure. Bread and bun production lines were associated with increased full-shift inhalable dust exposure, while cake production and substitution of dusting with the use of divider oil were associated with decreased exposure. Production tasks and characteristics are strong predictors of personal full-shift exposures to flour dust among bakers; these can be altered to reduce exposure levels. © 1997 British Occupational Hygiene Society. Published by Elsevier Science Ltd.

Byssinosis in Guangzhou, China.

To study the prevalence of byssinosis and other respiratory abnormalities in workers exposed to cotton dust in Guangzhou in two factories that processed purely cotton. All the 1320 workers exposed were included. The controls were 1306 workers with no history of occupational dust exposure. Total dust and inhalable dust were measured by Chinese total dust sampler and American vertical elutriator respectively. A World Health Organisation questionnaire was used. Forced vital capacity (FVC) and forced expiratory volume in one second (FEV1) were measured by a Vitalograph spirometer. The median inhalable dust concentrations ranged from 0.41 to 1.51 mg/m3 and median total dust concentrations from 3.04 to 12.32 mg/m3. The prevalence of respiratory abnormalities in the cotton workers were (a) typical Monday symptoms 9.0%; (b) FEV1 fall by > or = 5% after a shift 16.8%; (c) FEV1 fall by > or = 10% after a shift 4.2%; (d) FEV1 < 80% predicted 6.1%; (e) FEV1/FVC < 75% 4.0%; (f) cough or phlegm 18.2%; (g) chronic bronchitis 10.9%; and (h) byssinosis, defined by (a) plus (b) 1.7%. With the exception of (d), most of the prevalences increased with increasing age, duration of exposure, and cumulative inhalable dust exposure. No increasing trends of respiratory abnormalities were found for current total dust, inhalable dust, and cumulative total dust concentrations. Compared with controls, after adjustment for sex and smoking, with the exception of (d), all the pooled relative risks of respiratory abnormalities were raised for cotton exposure. It is concluded that cumulative inhalable cotton is likely to be the cause of byssinotic symptoms, acute lung function decrements, cough, or phlegm, and chronic bronchitis.

Dust exposure indices and lung function changes in Longshoremen and Dock workers

A group of Dutch harbor workers involved in loading and unloading bulk products from sea vessels such as coal, cokes, and some other products like alumina, borax, phosphate ore, and vermiculite was studied. Exposures were characterized by personal and environmental monitoring. This information was subsequently used to estimate several dust exposure indices and to study relationships with lung function variables and respiratory symptoms. Average respirable dust exposure levels ranged from 0.3-4.0 mg/m3. Workers involved in unloading products from sea vessels were exposed to the highest dust levels. Supervisors and workers with tasks in the dock had an intermediate to low exposure. Office workers had the lowest exposure to respirable dust. Inhalable dust levels were considerably higher and average exposures ranged from 0.3-80 mg/m3. The ranking of occupational titles by inhalable dust exposure was almost identical to the rank order of respirable dust levels. Workers with higher current and cumulative dust exposures tended to have a lower lung function, and only shortness of breath had a statistically significant relationship with current and cumulative inhalable dust exposure. In general, relationships between lung function and inhalable dust levels tended to be somewhat stronger in terms of statistical significance, because inhalable dust is an estimate of dust deposition in the upper airways and lung function is a measurable parameter of airway obstruction in that region. However, the differences with respirable dust were minimal, and variability in dust exposure levels was extremely large for this population. It was concluded that harbor workers involved in unloading ships containing coal and various kinds of ore can be exposed to high dust levels. Relationships between dust exposure and lung function illustrate that these exposures are a respiratory hazard. Our finding that inhalable dust levels have a somewhat stronger relationship with lung function level than respirable dust levels deserves further attention.

Characterization of exposure to inhalable flour dust in Swedish bakeries.

Bakery workers are at risk of developing respiratory symptoms, such as asthma and rhinitis. Exposure to inhalable flour dust in 12 Swedish bakeries was therefore determined: concentrations of airborne inhalable flour dust were measured with the IOM personal inspirable dust sampler and the particle size distribution assessed using the IOM personal inspirable aerosol spectrometer, and the fractions of alpha-amylase, water-soluble protein and total protein in flour dust were determined. A total of 129 measurements were performed of which 77 were repeated measurements. There was a clear hierarchy in geometric mean exposure among bakery workers, with in descending order doughmakers (5.46 mg m-3), bread-formers (2.69 mg m-3), oven workers (1.17 mg m-3), and packers and confectionery workers (0.53 mg m-3). The repeated measurements revealed that within each task group there were considerable differences in mean exposure among the workers: this was demonstrated by geometric standard deviations of between-worker variance of 1.63-1.77. Partitioning of the total variability of inhalable flour dust exposure showed that the task group was the principal source of variance, accounting for 61-69% of the total variability. The optimum grouping strategy was independent of whether the oven workers and the packers were assigned to the same or to different task groups. The doughmakers and the bread-formers are two clearly distinguishable exposure groups with largely overlapping exposure distributions. On average, the flour dust contained 9% total protein, 2.3% water-soluble protein and 0.03% alpha-amylase. The inhalable flour dust was characterized by a substantial proportion of particles with a d(ac) above 10 microns. It was estimated that the thoracic subfraction contributed 39% to the total mass of inhalable dust, and the respirable subfraction 19%.

WOOD DUST EXPOSURE DURING FURNITURE MANUFACTURE—RESULTS FROM AN AUSTRALIAN SURVEY AND CONSIDERATIONS FOR THRESHOLD LIMIT VALUE DEVELOPMENT

A survey of time-weighted average (TWA) personal inhalable dust exposures for woodworkers in 15 Australian furniture factories was undertaken. There was significant variation in the individual dust measurements with mean exposures of 3.2, 5.2, and 3.5 mg/m3 for wood machinists, cabinetmakers, and chair framemakers, respectively. Hardwoods, softwoods, and reconstituted woods are used in the industry, but only minor differences in mean exposures or particle size distributions were found for the broad categories. In addition, a modified British Medical Research Council respiratory questionnaire was used to obtain information about work-related symptoms and job activities. Compared with a control group, the woodworkers reported more eye, ear, and nasal problems, with the differences being statistically significant. However, among the woodworkers themselves, with the exception of several nasal symptoms, the prevalences of reported symptoms were poorly correlated with gravimetric measurements of personal dust exposure. The problem of selection bias in cross-sectional studies is discussed. For a mean TWA personal exposure of about 3 mg/m3, hardwood users were more likely to report nasal symptoms than users of reconstituted wood. The question of appropriate exposure standards for woods in general is addressed by reference to those important health effects, besides sino-nasal cancer, that have been investigated. Further exposure guidelines should be formulated for groups of woods that are known to cause a common health effect, such as nasal/respiratory sensitization.