Influence Of Temperature Research Articles

The Influence of Aging Temperatures on the Microstructure and Stress Relaxation Resistance of Cu-Cr-Ag-Si Alloy

The Influence of Aging Temperatures on the Microstructure and Stress Relaxation Resistance of Cu-Cr-Ag-Si Alloy

Diel transcriptional responses of coral-Symbiodiniaceae holobiont to elevated temperature

Coral exhibits diel rhythms in behavior and gene transcription. However, the influence of elevated temperature, a key factor causing coral bleaching, on these rhythms remains poorly understood. To address this, we examined physiological, metabolic, and gene transcription oscillations in the Acropora tenuis-Cladocopium sp. holobiont under constant darkness (DD), light-dark cycle (LD), and LD with elevated temperature (HLD). Under LD, the values of photosystem II efficiency, reactive oxygen species leakage, and lipid peroxidation exhibited significant diel oscillations. These oscillations were further amplified during coral bleaching under HLD. Gene transcription analysis identified 24-hour rhythms for specific genes in both coral and Symbiodiniaceae under LD. Notably, these rhythms were disrupted in coral and shifted in Symbiodiniaceae under HLD. Importantly, we identified over 20 clock or clock-controlled genes in this holobiont. Specifically, we suggested CIPC (CLOCK-interacting pacemaker-like) gene as a core clock gene in coral. We observed that the transcription of two abundant rhythmic genes encoding glycoside hydrolases (CBM21) and heme-binding protein (SOUL) were dysregulated by elevated temperature. These findings indicate that elevated temperatures disrupt diel gene transcription rhythms in the coral-Symbiodiniaceae holobiont, affecting essential symbiosis processes, such as carbohydrate utilization and redox homeostasis. These disruptions may contribute to the thermal bleaching of coral.

Enhancement of terephthalic acid recovered from PET waste using a combination of citric acid and dimethyl sulfoxide extraction

This study aimed to develop an eco-friendly, cost-efficient, and practically viable method for extracting terephthalic acid (H2BDC) from polyethylene terephthalic (PET) waste. Dimethyl sulfoxide (DMSO) was combined with either citric acid (C6H8O7) or H2SO4 to enhance the particle size of H2BDC, and the optimum conditions during the acidification step were determined. Additionally, response surface methodology was employed to examine the influence and interaction of extractant (NaOH) concentration, hydrolysis temperature, and time on the optimal H2BDC yield and recovery ratio. Experimental results demonstrated that NaOH concentration significantly impacted both H2BDC yield and recovery ratio, surpassing the effects of hydrolysis temperature and time. Under optimal conditions involving a temperature of 200 °C and a 12 h reaction time with 5% NaOH, the model predicted a 100% yield and recovery ratio, which closely matched the experimental results of 99% and 100% for yield and recovery ratio, respectively. To enhance particle size, a combination of DMSO and C6H8O7 was more effective than H2SO4. The maximum particle size achieved was 57.4 µm under the following optimum conditions: premixing 5 M C6H8O7 with DMSO at a 35:75 mL ratio and maintaining a reaction temperature of 75 °C for 40 min. The study demonstrated the stability and consistency of the method. The H2BDC yield remained between 96 and 98% with high purity over eight consecutive cycles of using the DMSO and C6H8O7 mixture. The findings highlight the importance of integrating C6H8O7 and DMSO to enhance H2BDC quality, meeting commercial product criteria with evidence of high purity and large particle size. This method presents a promising solution for extracting H2BDC from PET waste, with potential implications for the recycling industry and a positive environmental impact.

Atomic layer deposition of Al-doped ZnO nanomembrane with in situ monitoring

Due to shortcomings such as poor homogeneity of Al doping, precisely controlling the thickness, inability to conformally deposit on high aspect ratio devices and high pinhole rate, the applications of Al-doped ZnO (AZO) nanomembrane in integrated optoelectronic devices are remarkably influenced. Here, we report in situ monitoring during the atomic layer deposition (ALD) of AZO nanomembrane by using an integrated spectroscopic ellipsometer. AZO nanomembranes with different compositions were deposited with real-time and precise atomic level monitoring of the deposition process. We specifically investigate the half-reaction and thickness evolution during the ALD processes and the influence of the chamber temperature is also disclosed. Structural characterizations demonstrate that the obtained AZO nanomembranes without any post-treatment are uniform, dense and pinhole-free. The transmittances of the nanomembranes in visible range are >94%, and the optimal conductivity can reach up to 1210 S cm−1. The output of current research may pave the way for AZO nanomembrane to become promising in integrated optoelectronic devices.

Dynamics of the lipid body lipidome in the oleaginous yeast Yarrowia sp.

Time dependent changes in the lipid body (LB) lipidome of two oleaginous yeasts, Yarrowia lipolytica NCIM 3589 and Yarrowia bubula NCIM 3590 differing in growth temperature was investigated. LB size and lipid content were higher in Y. lipolytica based on microscopy, Feret and integrated density analysis with lipid accumulation and mobilization occurring at 48h in both strains. Variations in LB lipidome were reflected in interfacial tension (59.67 and 68.59 mN m-1) and phase transition temperatures (30-100 and 60-100°C) for Y. lipolytica and Y. bubula, respectively. LC-MS analysis revealed neutral lipids, phospholipids, sphingolipids, sterols, fatty acids as the major classes present in both strains while fatty acid amides were seen only in Y. lipolytica. Amongst the lipid classes a few species were present in abundance with a number of lipids being less dominant. PERMANOVA and ANOCOVA analysis suggest 22 lipids belonging to neutral lipids, fatty acid amides and free fatty acids were found to be statistically different between the two strains. Analysis of the ratios between different lipid components suggest changes in LB size and mobilization as a function of time. The results indicate influence of temperature and strain variation on the dynamics of LB lipidome in Yarrowia species.

Influence of Temperature on Characteristics of a Diode with a p-n Junction in a Magnetic Field

Influence of Temperature on Characteristics of a Diode with a p-n Junction in a Magnetic Field

Response of the human choroid to short-term changes in eyelid and periocular temperature

ABSTRACT Clinical relevance Choroidal thickness measurement is gaining popularity in clinical practice and research as an early indicator of myopia progression. Understanding the influence of temperature on choroidal thickness changes will improve the reliability of the measures. Background It has been suggested that environmental temperature may affect choroidal thickness and blood flow, with potential implications for ocular disease and refractive development. This study investigates the effect of changes in eyelid/ocular adnexa temperature on choroidal thickness. Methods In a paired-eye study, 20 young, healthy subjects received a warm stimulus (heat pack) over one closed eye and simultaneously a cold stimulus (ice pack) over the other for 10 min. Eyelid temperatures were monitored with thermal probes, and optical coherence tomography scans of the retina and choroid were taken before and after heating and cooling, and then every 5 min during a 15-min recovery period. Retinal and choroidal thicknesses were measured across the macular region (6 mm), including the subfoveal (1 mm), parafoveal (1–3 mm), and perifoveal (3–5 mm) regions, and compared between the cooled and warmed eyes. Results When the thermal stimuli were applied, eyelid surface temperatures changed predictably and remained significantly different (by approximately 10–15°C) between the eyes after 2 min (p < .001). Relative to the warmed eye, macular choroidal thickness in the cooled eye increased significantly after 10 min of treatment (p = .004). This choroidal thickening response occurred in the subfoveal, parafoveal, and perifoveal regions (all p < .05). Upon removal of the thermal stimuli, choroidal thickness rapidly returned to the baseline and was no longer different between the cooled and warmed eye (p = .641). Conclusion Cooling the anterior eye by application of a cold stimulus directly onto the closed eyelid caused a small but significant increase in choroidal thickness relative to warming the anterior eye, demonstrating that the choroid can modulate its thickness rapidly and transiently in response to local temperature changes.

Investigation of the influence of pH and temperature on melanization and survival under oxidative stress in Cryptococcus neoformans.

Cryptococcus neoformans is an opportunistic pathogenic fungus that produces melanin during infection, an important virulence factor in Cryptococcal infections that enhances the ability of the fungus to resist immune defense. This fungus can synthesize melanin from a variety of substrates, including L-DOPA (L-3,4-dihydroxyphenylalanine). Since melanin protects the fungus from various stress factors such as oxidative, nitrosative, extreme heat and cold stress; we investigated the effects of environmental conditions on melanin production and survival. In this study, we investigated the effects of different pH values (5.6, 7.0 and 8.5) and temperatures (30°C and 37°C) on melanization and cell survival using a microtiter plate-based melanin production assay and an oxidative stress assay, respectively. In addition, the efficacy of compounds known to inhibit laccase involved in melanin synthesis, i.e., tunicamycin, β-mercaptoethanol, dithiothreitol, sodium azide and caspofungin on melanization was evaluated and their sensitivity to temperature and pH changes was measured. The results showed that melanin content correlated with pH and temperature changes and that pH 8.5 and 30°C, were best for melanin production. Besides that, melanin production protects the fungal cells from oxidative stress induced by hydrogen peroxide. Thus, changes in pH and temperature drastically alter melanin production in C. neoformans and it correlates with the fungal survival. Due to the limited antifungal repertoire and the development of resistance in cryptococcal infections, the investigation of environmental conditions in the regulation of melanization and survival of C. neoformans could be useful for future research and clinical phasing.

Decolorization, degradation, and detoxification of textile dye and efficient hydrogen production by highly-stable MIL-177-LT@NiFe-LDH photoelectrocatalyst: Mechanism and economical studies

Combining organic compounds with inorganic layers leads to the development of innovative organic-inorganic hybrid materials with specific functional properties, opening up possibilities for advanced applications that go beyond current technological limits. In the present study, Ti-MOF (MIL-177-LT) was decorated with NiFe layered double hydroxide (NiFe-LDH) to fabricate a heteroatom electrocatalyst (MIL-177-LT@NiFe-LDH). The synthesized electrode included capable electron transportation, long-term stability, and high specific surface area. Photoelectrocatalytic degradation of the Azo dye (Acid Red 18) from water was studied with respect to the influence of pH, bias potential, temperature, and dye concentration. It was found that hydrogen evolution reaction (HER) has minimized overpotentials, i.e., 130 and 182 mV corresponding to the current densities of 400 and 1000 mA cm−2, respectively. High stability was also observed when a current density of 5000 mA cm−2 was applied to the modified electrode for 500 h. The layered architecture of the MIL-177-LT@NiFe-LDH composite provides high surface points for the degradation of dye molecules and water splitting for HER. The electrocatalyst showed great stability in the degradation process. The experiment was powered by solar cells, reducing the need for electricity and resulting in cost savings. Additionally, the treatment process was analyzed in terms of costs. Therefore, a promising approach is suggested in this study for developing high-performance organic-inorganic hybrid materials with exceptional electrochemical and photocatalytic properties.

Influence of Temperature and Water Availability on Seed Germination of Cicer Milkvetch (Astragulus Cicer L.) and Purple Prairie Clover (Dalea Purpurea Vent. Var. Pupurea)

Global warming may leads a decrease in plant diversity and increased risk for some plant extinction does exist. The effect of temperature and water availability on seed germination were investigated in many plants, and are two of the most important factors on seed germination, for the plant survival that can result in a loss or increase under global climate change scenarios, by affecting a plant's recruitment success. Therefore, research on how climate change affects seed germination is essential for our research and ability to predict the risk for plants. To examine the possible effect of climate change on two commonly grown legumes a greenhouse experiment was run at at AAFC-SPARC. One was an introduced legume, cicer milkvetch, and the other a native legume, purple prairie clover. Our findings were: the experiment with warmer temperature and decreased soil moisture to research seed germination, the result is that reduction in the total both seed germination rate occurs, and showed the seed germination of purple prairie clover is better for the more stressful temperatures and water potentials examined in this experiment. For both legumes were examined on the control water potential the best temperature range is from 20℃ to 30℃ .

Influence of temperature on the compression properties of expanded thermoplastic polyurethane (ETPU)

This study explores how expanded thermoplastic polyurethane (ETPU) responds to temperature and compression at various temperatures. Dynamic mechanical thermal analysis (DMTA) was used to understand the temperature influence at small deformations. To investigate the deformation behavior at different compression stages we employed in-situ CT measurements and 3D strain mapping. Through quasi-static compression tests at temperatures from − 50 to 120 °C, we determined the influence of temperature on compression modulus, elastic stress, stress at 50% deformation, densification, and energy absorption. Remarkably, ETPU demonstrates robust recovery after compression, particularly within the − 50 to 60 °C temperature range. Subsequent compression tests show consistent or even slightly increased compression properties, such as a 10% increase in energy absorption for samples previously tested at − 40 °C, indicating that ETPU can withstand prior exposure to different temperatures.

Learning Model Based on Electrochemical Metallization Memristor with Cluster Residual Effect

Although a memristor model, subjected to electrochemical metallization mechanism, has been proposed based on the spontaneous decay of clusters in the previous work, it does not agree with the human forgetting accurately. Therefore, an improved model is meaningfully presented for the memristor with the cluster spontaneous decay by adding the residual effect. The former is due to the inward contraction of atoms driven by surface energy, while the latter is because of the balance of attractive and repulsive forces between atoms. The model fits well with the actual device. The forgetting is caused by the spontaneous decay. Memory retention is generated due to the added effect, which is also the internal cause of good agreement with the actual forgetting. Additionally, short‐term plasticity is converted to long‐term plasticity through the repeated learning. The efficiency of experiential learning using this model is much higher than that using the previous. It is shown that the physical mechanism of spontaneous decay in the cluster‐based channel is different from that in vacancy‐based or atom‐based channel. The model working under a non‐ideal condition with the temperature influence is discussed. Potential applications based on the model are stated.

Decoding influences of indoor temperature and light on neural activity: entropy analysis of electroencephalographic signals.

Understanding the neural responses to indoor characteristics like temperature and light is crucial for comprehending how the physical environment influences the human brain. Our study introduces an innovative approach using entropy analysis, specifically, approximate entropy (ApEn), applied to electroencephalographic (EEG) signals to investigate neural responses to temperature and light variations in indoor environments. By strategically placing electrodes over specific brain regions linked to temperature and light processing, we show how ApEn can be influenced by indoor factors. We also integrate heart indices from a multi-sensor bracelet to create a machine learning classifier for temperature conditions. Results showed that in anterior frontal and temporoparietal areas, neutral temperature conditions yield higher ApEn values. The anterior frontal area showed a trend of gradually decreasing ApEn values from neutral to warm conditions, with cold being in an intermediate position. There was a significant interaction between light and site factors, only evident in the temporoparietal region. Here, the neutral light condition had higher ApEn values compared to blue and red light conditions. Positive correlations between anterior frontal ApEn and thermal comfort scores suggest a link between entropy and perceived thermal comfort. Our quadratic SVM classifier, incorporating entropy and heart features, demonstrates strong performance (until 90% in terms of AUC, accuracy, sensitivity, and specificity) in classifying temperature sensations. This study offers insights into neural responses to indoor factors and presents a novel approach for temperature classification using EEG entropy and heart features.

Engineering and microstructural properties of environmentally friendly alkali-activated composites containing clinker aggregate: heat-curing regime and elevated-temperature effect

The common wisdom in the literature about clinker aggregate (CA) is that it improves the performance properties of mortar or concrete to some extent. The current study, in this context, investigated the physical characteristics and mechanical performances of alkali-activated composites (AACs) made entirely with CA. The CA was used in three particle sizes of 0–2 mm (named No.10), 2–4 mm (named No.5), and 4–8 mm (named medium). To examine the impact of the fine CA-size fraction on the characteristics of AAC, No.10 CA was partially replaced by No.5 CA up to 50%, while the content of the medium CA was kept constant in all AAC mixtures. Moreover, to evaluate the influence of the 8-h curing temperature on the performance of the AACs, different temperature-based curing strategies (ambient, 45, and 75 °C) were applied to the AACs. In the production of AACs, granulated blast furnace slag was employed as an aluminosilicate-rich raw material, and a sodium silicate and sodium hydroxide combination was used as an alkaline activator. Physical properties (flowability, water absorption, capillary water absorption, and dry unit weight), and 8-h strength performances (flexural and compressive) were determined. Furthermore, to monitor the influence of high temperatures on the characteristics of the AAC, the mixtures were exposed to elevated temperatures (200, 500, and 800 °C). In SEM image analysis, it was determined that spherical CSH gels were formed in the heat-cured AACs. It has been observed that the geopolymerization products decompose in AACs exposed to 800 °C. To evaluate statistically the experimental results, a multi-factor analysis of variance (ANOVA) was also applied. The results revealed that increasing the coarser fine aggregate fraction led to higher water absorption and apparent porosity capacities and lower unit weight. Besides, strength performance was improved by applying a heat-curing strategy to the AAC, whereas a decrease was observed by increasing the No.5 CA fraction. There was a remarkable reduction in compressive strength and considerable loss of mass when the AAC mixes were exposed to high temperatures.

Using Mössbauer Spectroscopy to Evaluate the Influence of Heat Treatment on the Surface Characteristics of Additive Manufactured 316L Stainless Steel

The oxidation behaviour of iron-based 316L stainless steel was investigated in the temperature range of 700 to 1000 °C. The test specimens in the shape of plates were produced by selective laser melting. After fabrication, the samples were sandblasted and then annealed in air for different periods of time (0.5, 2, 8, 32 h). Under the influence of temperature and time, stainless steels tend to form an oxide layer. Scanning electron microscopy, energy dispersive analysis, and X-ray diffraction were employed to analyse the composition of this layer. Notably, a thin oxide layer primarily composed of (Fe-Cr) formed on the surface due to temperature effects. In addition, with increasing temperature (up to 1000 °C), the oxide of the main alloying elements, specifically Mn2(Fe-Cr)O4, appeared alongside the Fe-Cr oxide. Furthermore, the samples were subjected to conversion X-ray (CXMS) and conversion electron (CEMS) Mössbauer spectroscopy. CXMS revealed a singlet with a decreasing Mössbauer effect based on the surface metal oxide thickness. CEMS revealed the presence of Fe3+ in the surface layer (0.3 µm). Moreover, an interesting phenomenon occurred at higher temperature levels due to the inhomogeneously thick surface metal oxide layer and the tangential direction of the Mössbauer radiation towards the electron detector.

Effect of thermal ageing on fatigue crack growth behaviour of forged alloy 617M at elevated temperatures

ABSTRACT Fatigue crack growth (FCG) studies have been conducted on compact tension specimens of alloy 617M for as-received and aged for 1000, 5000 and 10,000 h at 710°C. Effects of thermal ageing on FCG behaviour of alloy 617M forged has been characterised at 27°C, 650°C, 710°C and 750°C. Results reveal that threshold stress intensity factor ( Δ K th ) decreases as temperature increases upto 710°C and then increases at 750°C for all the ageing conditions except for 1000 h aged. The Δ K th value also decreases with an increase in ageing time till 5000 h, but at 10,000 h a reverse trend is observed. The influence of thermal ageing and temperature reflects major deviations for Paris constant (C) and exponent (m). Additionally, thermal ageing and temperature influences on FCG, the effects of dynamic strain ageing, Cr-rich carbides and γ’-phase precipitations have been discussed and corroborated with fractographic and microstructural changes.

The Influence of Atmospheric Air Temperature and Humidity on the Heat Pump COP

The Influence of Atmospheric Air Temperature and Humidity on the Heat Pump COP

Modeling and self-supporting printing simulation of fuse filament fabrication

This study presented a comprehensive computational fluid dynamics-based model for fused filament fabrication (FFF) three-dimensional (3D) printing multiphase and multiphysics coupling. A model based on the framework of computational fluid dynamics was built, utilizing the front-tracking method for high precision of multiphase material interfaces, a fully resolved simulation at the mesoscale explores the underlying physical mechanism of the self-supported horizontal printing. The study investigated the influence of printing temperature and velocity on the FFF process, exhibiting a certain self-supporting forming ability over a specific range. The results indicated that during the printing of large-span horizontal extension structures, the bridge deck material transitions from initial straight extension to sagging deformation, ultimately adopting a curved shape. The straight extension distance is inversely proportional to the depth of the sagging deformation. Additionally, the study revealed that printing temperature primarily affected the curing time of the molten material, while printing velocity fundamentally affected the relaxation time of both thermal and dynamic characteristics of the material.

Diurnal and seasonal dynamics of the canopy‐layer urban heat island of Kuwait

AbstractThis study examines the temporal and spatial variability of near‐surface air temperature and the canopy layer urban heat island (UHICL) of Kuwait City. Observations collected at 12 locations across the country of Kuwait and for the period 2010–2022 are analysed on an hourly and 3‐hourly basis to provide monthly and diurnal insights of the city's UHICL characteristics. Research on Kuwait's UHICL was first conducted by Nasrallah et al. (International Journal of Climatology, 10, 401–405). Results presented here have been afforded the benefit of additional stations and more extensive data compared with the earlier study. Mean positive UHICL intensities, ranging from 1.1°C to 3.8°C at night, are observed consistently across all months, owing to the prevalence of clear skies from winter to summer. Negative UHICL intensities, indicating a typical daytime urban cool island (UCICL), are most prominent on summer days, exhibiting a mean hourly magnitude range between 0.6°C and 2.6°C that extends into the early parts of the evening. Heat and cool island effects are maintained up to wind speeds approaching 10 m s−1 at the urban periphery. A coastal site near the city demonstrates strong influences of the Arabian Gulf temperatures and associated sea and land breeze effects on UHICL development. The results can be used for comparison with other desert locales, in the evaluation of urban climate models, for urban planning policies and improving local weather forecasts. This study honours in memoriam Dr. Hassan Nasrallah, who produced the first UHICL study in the Arab World.

Effect of Temperature on Some Biological Indicators of Cydia pomonella Linnaeus, 1758

In 2022-2023 The influence of temperature on the development and reproduction of the codling moth butterfly was studied. Experiments have shown that the optimal temperature regime for mass reproduction of the codling moth in laboratory conditions is within 20-25°C. At low temperatures (15°C), butterflies live 34-35 days, and some individuals can live up to 45-50 days. This shows that these characteristics of butterflies allow them to remain viable in an unfavorable environment, although their reproduction is reduced. The experiments carried out make it possible to obtain the necessary temperature parameters for the development of fruit-eating apple trees.