Indentation Modulus Research Articles

Influence of chemical composition on the room temperature plasticity of C15 Ca-Al-Mg Laves phases

The influence of chemical composition changes on the room temperature mechanical properties in the binary Ca33Al67C15 CaAl2 Laves phase were investigated in two ternary alloys with off-stoichiometric compositions with 5.7 at.% Mg substitution (Ca33Al61Mg6) and 10.8 at.% Mg and 3.0 at.% Ca substitution (Ca36Al53Mg11) and compared to the stoichiometric (Ca33Al67) composition. Cubic Ca-Al-Mg Laves phases with multiple crystallographic orientations were characterised and deformed using nanoindentation. The hardness and indentation modulus were measured to be 4.1 ± 0.3 GPa and 71.3 ± 1.5 GPa for Ca36Al53Mg11, 4.6 ± 0.2 GPa and 80.4 ± 3.8 GPa for Ca33Al61Mg6 and 4.9 ± 0.3 GPa and 85.5 ± 4.0 GPa for Ca33Al67, taken from our previous study, respectively. The resulting surface traces as well as slip and crack planes, were distinguished on the indentation surfaces, revealing the activation of several different {11n} slip systems, as further confirmed by conventional transmission electron microscopic observations. Additionally, the deformation mechanisms and corresponding energy barriers of activated slip systems were evaluated by atomistic simulations.

Investigation and Optimization of The Effect of Anhydrous Borax Mineral on The Vickers Hardness and Indentation Modulus Values of Iron Material

In this study, 5% and 10% by weight of anhydrous borax (AHB) was added to the iron (Fe) matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness (HV), Brinell hardness (HB) and Indentation modulus (EIT) values of the composites (Fe/AHB) were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical and/or mechanical properties of the Fe/AHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and Fe/AHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio (S/N) analysis performed with the experimental data, it was determined that the 10% AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the Fe/AHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03%, 69.32% and 144.11%, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

Analyzing fiber and vascular bundle characteristics, and micro-mechanical properties of Oligostachyum sulcatum

The structure of vascular bundles and the mechanical properties of fibers are crucial factors determining the utilization of bamboo. This study investigated the structure of vascular bundles and evaluated the morphological and micromechanical properties of the fibers in Oligostachyum sulcatum. The results showed that the fiber length and width of O. sulcatum meet the requirements of raw materials for the papermaking process. However, the fiber content in O. sulcatum is relatively low, which may increase the cost of papermaking. The vascular bundle growth exhibited non-uniformity, especially at the top part, with no discernible pattern in bundle area changes. The nanoindentation testing demonstrated that the bamboo’s indentation modulus of elasticity (IMOE) and hardness values were comparable to those of moso bamboo (Phyllostachys edulis), suggesting its potential as a substitute in engineering applications.

Influence of Polymer Flow on Polypropylene Morphology, Micro-Mechanical, and Tribological Properties of Injected Part

This research investigates the micro-mechanical and tribological properties of injection-molded parts made from polypropylene. The tribological properties of polymers are a very interesting area of research. Understanding tribological processes is very crucial. Considering that the mechanical and tribological properties of injected parts are not uniform at various points of the part, this research was conducted to explain the non-homogeneity of properties along the flow path. Non-homogeneity can be influenced by numerous factors, including distance from the gate, mold and melt temperature, injection pressure, crystalline structure, cooling rate, the surface of the mold, and others. The key factor from the micro-mechanical and tribological properties point of view is the polymer morphology (degree of crystallinity and size of the skin and core layers). The morphology is influenced by polymer flow and the injection molding process conditions. Gained results indicate that the indentation method was sufficiently sensitive to capture the changes in polypropylene morphology, which is a key parameter for the resulting micro-mechanical and tribological properties of the part. It was proven that the mechanical and tribological properties are not equal in varying regions of the part. Due to cooling and process parameters, the difference in the indentation modulus in individual measurement points was up to 55%, and the tribological properties, in particular the friction coefficient, showed a difference of up to 20%. The aforementioned results indicate the impact this finding signifies for injection molding technology in technical practice. Tribological properties are a key property of the part surface and, together with micro-mechanical properties, characterize the resistance of the surface to mechanical failure of the plastic part when used in engineering applications. A suitable choice of gate location, finishing method of the cavity surface, and process parameters can ensure the improvement of mechanical and tribological properties in stressed regions of the part. This will increase the stiffness and wear resistance of the surface.

Microstructure, properties and damage characteristics of designed PyC interphase in Cf/SiC mini-composites

Pyrolytic carbon (PyC) interphase plays a crucial role in improving the mechanical properties of fiber-reinforced ceramic-matrix composites (FRCMCs). In this paper, three groups of PyC interphase were prepared: the first group (G1) with a mid-high texture PyC (MT-HT-PyC) interphase, the second group (G2) with a low/high texture combination PyC (LT/HT-PyC), and the third group (G3) with a low texture PyC (LT-PyC). The microstructure, intrinsic properties and interfacial properties of these three groups PyC interphase were characterized by SEM, TEM, Raman spectroscopy, nanoindentation tests, and fiber push-in tests. The result showed the LT-PyC with more amorphous PyC lattice and lattice defects is able to reduce the indentation modulus and interfacial properties of PyC interphase. The uniaxial tensile tests revealed that the Cf/SiC mini-composites containing a LT-PyC interphase could significantly improve their tensile strength, exhibiting a 34 % enhancement in tensile strength compared to those counterparts without LT-PyC interphase. The experimental result of scanning ion beam etching (SIBN) also showed that the interfacial crack propagates primarily within the LT-PyC interphase, rather than along the interface between the fiber and the interphase.

Mechanical Properties of High- and Low-Fusing Zirconia Veneering Ceramics Fired on Different Trays and Substrates.

This study aimed to evaluate the effect of ceramic type, firing tray, and firing substrate on the density, shrinkage, biaxial flexural strength, Martens' hardness, and elastic indentation modulus of zirconia veneering ceramics. Disk-shaped specimens were fabricated from a high-fusing (HFZ) and a low-fusing (STR) zirconia veneering ceramic. These specimens were then divided into 10 groups according to firing trays (round, small honeycomb-shaped, cordierite [RSC]; round, large honeycomb-shaped, aluminum oxide [RLA]; rectangular, plane, silicon nitride [RCPS]; round, plane, silicon nitride [RPS]; and rectangular, plane, calcium silicate [RCPC]) and firing substrates (firing cotton and platinum foil) used (n = 12). The density, shrinkage, biaxial flexural strength, Martens' hardness, and indentation modulus were measured, and analyzed with generalized linear model analysis (α = 0.05). The interaction between the ceramic type and firing substrate affected density (p < 0.001), and the other outcomes were affected by the interaction among all main factors (p ≤ 0.045). Higher density was observed with HFZ or platinum foil (p ≤ 0.007). RSC and RLA led to a higher density than RCPS within HFZ and led to the lowest density within STR (p ≤ 0.046). STR had a higher shrinkage (p < 0.001). RSC mostly led to a lower shrinkage of HFZ (p ≤ 0.045). The effect of ceramic type and firing substrates on the biaxial flexural strength, Martens' hardness, and indentation modulus was minimal while there was no clear trend on the effect of firing tray on these properties. Ceramic type, firing tray, and firing substrate affected the mechanical properties of the tested zirconia veneering ceramics. Firing the tested zirconia veneering ceramics over a round and small honeycomb-shaped cordierite firing tray with firing cotton mostly led to improved mechanical properties.

Effects of printing orientation and artificial ageing on martens hardness and indentation modulus of 3D printed restorative resin materials

BackgroundThree-dimensional (3D) printing is increasingly used to fabricate dental restorations due to its enhanced precision, consistency and time and cost-saving advantages. The properties of 3D-printed resin materials can be influenced by the chosen printing orientation which can impact the mechanical characteristics of the final products. PurposeThe objective of this study was to evaluate the influence of printing orientation and artificial ageing on the Martens hardness (HM) and indentation modulus (EIT) of 3D-printed definitive and temporary dental restorative resins. MethodsDisk specimens (20 mm diameter × 2 mm height) were additively manufactured in three printing orientations (0°, 45°, 90°) using five 3D-printable resins: VarseoSmile Crownplus (VCP), Crowntec (CT), Nextdent C&B MFH (ND), Dima C&B temp (DT), and GC temp print (GC). The specimens were printed using a DLP 3D-printer (ASIGA MAX UV), while LavaTM Ultimate (LU) and Telio CAD (TC) served as milled control materials. Martens hardness (HM) and indentation modulus (EIT) were tested both before and after storage in distilled water and artificial saliva for 1, 30, and 90 days at 37 °C. Results90° printed specimens exhibited higher HM than the other orientations at certain time points, but no significant differences were observed in HM and EIT between orientations for all 3D-printed materials after 90 days of ageing in both aging media. LU milled control material exhibited the highest HM and EIT among the tested materials, while TC, the other milled control, showed similar values to the 3D printed resins. CT and VCP (definitive resins) and ND displayed higher Martens parameters compared to DT and GC (temporary resins). The hardness of the 3D-printed materials was significantly impacted by artificial ageing compared to the controls, with ND having the least hardness reduction percentage amongst all 3D-printed materials. The hardness reduction percentage in distilled water and artificial saliva was similar for all materials except for TC, where higher reduction was noted in artificial saliva. SignificanceThe used 3D printed resins cannot yet be considered viable alternatives to milled materials intended for definitive restorations but are preferable for use as temporary restorations.

Experimental studies on mechanical properties of Al-7075/TiO2 metal matrix composite and its tribological behaviour

This study explores the fabrication and characterization of an Al-7075/TiO2 metal matrix composites (MMCs) through stir casting, varying TiO2 contents from 2% to 10%. Various tests, including tensile, hardness, and elastic indentation modulus testing, dynamic mechanical analysis, microstructural evaluation, and XRD, were conducted. Tribological analysis involved tribo-pairs of an EN31 disc and a smooth MMCs pin, using a high-temperature Pin-on-disc setup. Microstructural analysis of Al-7075/TiO2 MMCs revealed uniform TiO2 distribution, grain refinement, and enhanced mechanical properties, with XRD confirming structural changes. Tensile tests showed improved ultimate force and stress with increasing TiO2 content, indicating potential for high-strength applications. Hardness assessments demonstrated progressive improvements in Martens, Elastic Indentation, and Vickers Hardness, highlighting the material's suitability for critical wear and tribology applications. The composites exhibited enhanced damping flexural characteristics, especially with 8% TiO2. Maximum and minimum modulus values are reported as 98.9 GPa at 25 °C and 77.3 GPa at 350 °C for 8% TiO2 mix MMC. Tribological performance was improved with lower COF values and wear rates. At elevated temperatures, the wear behavior varied with TiO2 content, influenced by factors such as heat generation and localized welding.

Synthesis and characterization of ceramic high entropy carbide thin films from the Cr-Hf-Mo-Ta-W refractory metal system

We use reactive DC magnetron sputtering to showcase synthesis strategies for multicomponent carbides with the NaCl-type fcc structure and illustrate how deposition conditions allow controlling the formation of metallic and ceramic single phases in the Cr-Hf-Mo-Ta-W system. The synthesis is performed in argon flow and different acetylene flows from 0 to 12sccm, at ambient and elevated temperatures (700 °C), respectively, hindering/promoting the adatom diffusion. Structural and microstructural investigations reveal the formation of the bcc metallic phase (a=3.188−3.209Å) in films deposited without acetylene flow, also supported by ab initio density function theory (DFT) analysis of lattice parameters as a function of the C content. Experimentally, a bcc-to-fcc phase transition is observed through the formation of an amorphous coating. Contrarily, samples deposited in higher acetylene flow show an fcc multielement carbide phase (a=4.33−4.49 Å). The crystalline films reveal columnar morphology, while the amorphous ones are very dense. We report promising mechanical properties, with hardness up to 25±1GPa. The indentation moduli reach up to 319±6GPa and show trends consistent with DFT predictions. Our study paves the path towards the preparation of Cr-Hf-Mo-Ta-W multicomponent carbides by magnetron sputtering, showing promising microstructure as well as mechanical properties.

Bark cloth structure and properties: A naturally occurring fabric and ancestral textile craft from Uganda

Natural fabrics from two bark trees of Uganda (“Kilundu”: Antiaris toxicaria and “Mutuba”: Ficus natalensis) are being considered today for the local footwear industry. Here, we thoroughly examined to determine their structural, biochemical and mechanical properties of the two bark cloths, in order to ascertain their potential use as locally-available, low-cost composite reinforcements and eventually for a use in textile industry as well. Fibres in both fabrics are rich in highly crystalline cellulose (76.6 ± 4.9% and 66.3 ± 0.5%) and have very cohesive cell walls with small lumen size and stiff middle lamellae. However, their low indentation modulus is due to a high microfibrillar angle, penalizing their longitudinal stiffness but making them interesting for impact or deformation performance. The two fabrics exhibit layers of preferred fibres orientations, quasi similar to unidirectional or +/-45° preforms, and hence may be used “as produced” as polymer reinforcements in technical composites but also in textile sector, in place of leather. Finally, their water uptake behaviour (21.2%-wt for Mutuba and 13.8%-wt for Kilundu) indicates opportunities for a range of environmentally-sensitive applications.

Imaging the mechanical properties of nanowire arrays

Abstract Dimensional and contact resonance (CR) images of nanowire (NW) arrays (NWAs) are measured using our newly developed microprobe CR imaging (CRI) setup. Then a reference method is employed to calculate the indentation modulus of NWs (M i,NW ) representing the elasticity of NWs, by measuring NWAs and reference samples at the same static probing force. Furthermore, topography is imaged in combination with CR and M i,NW separately by software, in which the z values indicate the topography of the NWs and the color bars show its CR or M i,NW . Then NWs’ topography relation to M i,NW is visualized. As typical examples, 3D imaging of topography and measurement of M i,NW is performed with Si&lt;111&gt; pillar arrays as well as Cu and ZnO NWAs. The novel method enables fast mechanical performance measurements of large-scale vertically-aligned NWAs without releasing them from their respective substrates. For instance, the diameter and pitch of the Si&lt;111&gt; pillars and the diameter of the Cu NWAs are in good agreement with the values measured by scanning electron microscopy (SEM). The position of ZnO NWs bunches grown at arbitrary sites on silicon can be identified with the help of combined topography and indentation modulus images. Furthermore, M i,NW measured by our homemade CRI setup agrees well with bulk values. Differences between the measured M i,NW and bulk M i values may be related to a size effect in NW elasticity.

Influence of Cr + Si content variation on cutting behavior of TiAlCrSiN HPPMS coatings

As high power pulse magnetron sputtering (HPPMS) technology is becoming popular in cutting tool industry, the development of nanocomposite coating systems such as TiAlCrSiN with this technology presents a new research avenue. Here, the combined effect of Cr and Si contents on properties and cutting behavior of high Al content TiAlCrSiN HPPMS coatings needs further investigation. For this purpose, three HPPMS coatings with Al/Ti ratio x = 1.4–1.5 and varying Cr + Si content, namely (Ti28Al40Cr16Si16)N, (Ti30Al43Cr17Si10)N and (Ti36Al54Cr5Si5)N, were deposited on cemented carbide substrates. In addition to basic characterization, the fracture behavior of the coatings was characterized by scratch tests. The cutting behavior of the coated inserts was exemplarily investigated during dry cutting of normalized medium carbon steel C45 with cutting speed vc = 80 m/min, feed rate f = 0.12 mm and cutting depth ap = 0.8 mm. The tool damage over the cutting time of tc = 35–40 min, as per the tool condition, was observed using light microscopy. Moreover, the damage mechanisms were analyzed in detail at the end of the cutting test using scanning electron microscopy. All coatings showed comparable indentation hardness HIT and indentation modulus EIT. However, an increased Cr + Si content amplified the brittle fracture of the coating under sliding load of scratch test. Moreover, the workpiece material C45 showed a higher adhesion tendency to cutting insert with high Cr + Si content TiAlCrSiN coatings during cutting tests. The tool wear and built-up edge formation increased due to the combined effect of workpiece adhesions and amplified brittle fracture of the coating at considered cutting speed. On the other hand, the inserts with low Cr + Si content coating exhibited better cutting performance and reduced built-up edge formation based on the improved fracture behavior of the coating and lower adhesion tendency of workpiece material to the corresponding coated insert.

The Advanced Assessment of Nanoindentation-Based Mechanical Properties of a Refractory MoTaNbWV High-Entropy Alloy: Metallurgical Considerations and Extensive Variable Correlation Analysis

In the present study, a thorough examination of nanoindentation-based mechanical properties of a refractory MoTaNbVW high-entropy alloy (RHEA) was conducted. Basic mechanical properties, such as the indentation modulus of elasticity, indentation hardness, and indentation-absorbed elastic energy, were assessed by means of different input testing variables, such as the loading speed and indentation depth. The obtained results were discussed in terms of the elasto-plastic behavior of the affected material by the indentation process and material volume. Detailed analysis of the RHEA alloy’s nanoindentation creep behavior was also assessed. The effect of testing parameters such as preset indentation depth, loading speed, and holding—at the creep stage—time were selected for their impact. The results were explained in terms of the availability of mobile dislocations to accommodate creep deformation. Crucial parameters, such as maximum shear stress developed during testing (τmax), critical volume for dislocation nucleation (Vcr), and creep deformation stress exponent n, were taken into consideration to explain the observed behavior. Additionally, in all cases of mechanical property examination and in order to identify those input testing parameters—in case—that have the most severe effect, an extensive statistical analysis was conducted using four different methods, namely ANOVA, correlation matrix analysis, Random Forest analysis, and Partial Dependence Plots. It was observed that in most of the cases, the statistical treatment of the obtained testing data was in agreement with the microstructural and metallurgical observations and postulates.

Surface Composites Synthesized through the Incorporation of Atomic Layer Deposited AlOx into Nanoporous Fuzzy Tungsten.

The incorporation of energetic helium gaseous species into materials such as tungsten (W) imparts intrinsic surface fragility, yielding fuzzy tungsten. To enhance the robustness of the surface layers, aluminum oxide (AlOx) was deposited by atomic layer deposition into the fuzzy W. The conformally deposited ceramic yields a new class of surface composites. Structural characterization of the fuzzy W-AlOx composites through nanoindentation testing indicated enhanced indentation modulus (Eind) and hardness (Hind) and was modeled through various rules of mixtures approaches. The distribution of AlOx in fuzzy W was explored and a systematic study of the extent of incorporation of the AlOx into the fuzzy W was carried out. The synthesized composites may be utilized for improved structural characteristics, e.g., in reducing crack initiation and fracture.

Residual water and interfacial bonding effects on the mechanical performance of CNT/fly ash geopolymer binder

AbstractNowadays, geopolymers are advanced alternatives to cementitious materials, where their excellent chemical and fire resistance are some of its most appealing properties. Fly ash geopolymers enable the use of industrial waste materials while converting them into a novel binding material. Their production is accompanied by a much lower CO2 emission when compared to Portland cement. Reinforcing fly ash geopolymers with carbon nanotubes would significantly strengthen its microstructure and with this enhancing the long‐term mechanical and durability performance. The aim of this work is to use reactive molecular dynamics simulation method to optimize the mechanical properties of fly ash geopolymers with nano‐reinforced carbon nanotubes (CNTs). During this study, the impact of humidity and interfacial bonding strength between carbon nanotube and geopolymer is investigated. Our findings show that structural transformations under hydration process comes from the weakening of AlO bond, leading to the elongation of AlO and NaOH bonds, forming aluminum and sodium hydroxyls. Conversely, silicate is not sensitive to water and exhibits hydrophobic behavior. In addition, our results show that there is an optimal value of water content (7.17 wt.%) that makes the geopolymer nanostructure strengthen. The related elastic modulus rises by 21.56%, 20.60%, and 18.41% for Si/Al ratio of 1, 2, and 3, respectively. Inserting carbon nanofillers to fly ash nanostructure has remarkably shown an interesting strength enhancement. More precisely, when interfacial bonding concentration is around 19.36%, it is observed a positively increasing of the compressive strength, shear, indentation and elastic modulus with 39%, 65.2%, 72.3%, and 144.85%, respectively. Reduced density gradient supports that the interaction between carbon nanotube and fly ash geopolymer is dominated by a van der Waals one.

Effect of printing orientation on mechanical properties of 3D-printed orthodontic aligners.

The purpose of this study was to assess differences in the fundamental mechanical properties of resin-made three-dimensional (3D) printed orthodontic aligners according to the printing orientation. Twenty resin 3D-printed dumbbell-shaped specimens and 20orthodontic aligners were fabricated and postcured in nitrogen. Half of the specimens and aligners were built in horizontal (H), the other half in vertical (V)directions. The dumbbell-shaped specimens were loaded in atensile testing machine, while parts of the aligners were embedded in acrylic resin, ground, polished, and then underwent instrumented indentation testing (IIT). Mechanical properties that were assessed included the yield strength (YS), breaking strength (BS), plastic strain (ε), Martens hardness (HM), indentation modulus (EIT), elastic index (ηIT), and indentation relaxation (RIT). Data were analyzed statistically with independent t‑tests or Mann-Whitney tests at α = 5%. No significant differences were found between specimens or aligners printed either in ahorizontal or avertical direction (P > 0.05 in all instances). Overall, the 3D-printed aligners showed acceptable mechanical propertied in terms of YS (mean 19.2 MPa; standard deviation [SD] 1.7 MPa), BS (mean 19.6 MPa; SD 1.2 MPa), ε (mean 77%; SD 11%), HM (median 89.0 N/mm2; interquartile range [IQR] 84.5-90.0 NN/m2), EIT (median 2670.5 MPa; IQR 2645.0-2726.0 MPa), ηIT (median 27.5%; IQR 25.9-28.1%), and RIT (mean 65.1%; SD 3.5%). Printing direction seemed to have no effect on the mechanical properties of 3D-printed resin aligners, which are promising for orthodontic use.

Elucidating the Role of Lignin Type and Functionality in the Development of High-Performance Biobased Phenolic Thermoset Resins.

In this work, a series of biobased phenolic resins were developed starting from kraft and soda lignin, suitably functionalized through esterification by means of succinic anhydride. As a result of an extensive optimization study of the functionalization and curing reactions, clear correlations between lignin type and chemical-physical characteristics and the properties of the resulting phenolic resin systems were described. In particular, the esterification reaction through succinic anhydride was found to play a key role in enhancing the chemical reactivity and in facilitating the successful incorporation of lignin into the resin formulations. The obtained high-lignin-content thermoset materials were shown to exhibit tunable chemical (functionality, gel content, and cross-linking density), thermal (glass transition temperature and thermo-oxidative stability), and mechanical (surface hardness, indentation modulus, and creep behavior) characteristics, which could outperform those of fully oil-based reference phenolic resins by judicious control of lignin concentration and chemical characteristics. In particular, succinylated kraft lignin was found to enable more efficient incorporation into the cured systems. This work provides the first demonstration of the incorporation of succinic-anhydride-modified-lignin in the formulation of high-performance phenolic resins, ultimately contributing to the definition of structure-property-performance correlations for rational biobased material design in the context of advanced and sustainable manufacturing.

The Impact of NaOH on the Micro-Mechanical Properties of the Interface Transition Zone in Low-Carbon Concrete.

To tackle carbon emissions from cement production and address the decline in concrete's mechanical properties due to the substitution of cement with solid waste (glass powder) and natural mineral admixture (zeolite powder) materials, we employed glass powder and zeolite powder to create composite cementitious materials. These materials underwent alkali activation treatment with a 4% NaOH dosage, replacing 50% of cement to produce low-carbon concrete. Nanoindentation tests and mercury intrusion porosimetry (MIP) were employed to uncover the micro-mechanical properties and influencing mechanisms of alkali-activated low-carbon concrete. The results indicate a notable enhancement in the indentation modulus (19.9%) and hardness (25.9%) of alkali-activated low-carbon concrete compared to non-activated concrete. Simultaneously, the interfacial transition zone thickness decreased by 10 µm. The addition of NaOH led to a reduced volume fraction of pores (diameter >100 nm) and an increased fraction of pores (diameter < 100 nm), thereby reducing porosity by 2.6%, optimizing the pore structure of low-carbon concrete. The indentation modulus, hardness and volume fraction of the hydrated phase derived from Gaussian fitting analysis of the nanoindentation statistics showed that NaOH significantly improved the modulus and hardness of the hydration products of low-carbon concrete. This activation resulted in decreased LDC-S-H gel (low-density hydrated calcium silicate Ca5Si6O16(OH)·4H2O) and pore content, while the HD C-S-H gel (high-density hydrated calcium silicate Ca5Si6O16(OH)·4H2O) and CH (calcium hydroxide crystals Ca(OH)2) content increased by 13.91% and 23.46%, respectively. Consequently, NaOH influenced the micro-mechanical properties of low-carbon concrete by generating more high-density hydration products, reducing pore content, enhancing the pore indentation modulus and hardness, and shortening the interfacial transition zone. This study offers novel insights into reducing carbon emissions and promoting the use of solid waste (glass powder) and natural mineral admixture (zeolite powder) materials in concrete, contributing to the advancement of sustainable construction practices.

Nanoscale and Tensile-Like Properties by an Instrumented Indentation Test on PBF-LB SS 316L Steel.

The mechanical properties of a defect-free laser melting (PBF-LB) deposit of an AISI 316L steel alloy were assessed by means of an instrumented indentation test (IIT), at both the macro- and nano-scales. The inherent non-equilibrium microstructure of the alloy was chemically homogenous and consisted of equiaxed grains and large-elongated grains (under the optical microscope) with irregular outlines composed of a much finer internal cell structure (under the scanning electron microscope). Berkovich and Vickers indenters were used to assess the indentation properties across individual grains (nano) and over multiple grains (macro), respectively. The nano-indentation over the X-Y plane revealed nearly constant indentation modulus across an individual grain but variable on average within different grains whose value depended on the relative orientation of the individual grain. The macro-indentation test was conducted to analyze the tensile-like properties of the polycrystalline SS 316L alloy over the X-Y and Y-Z planes. The macro-indentation test provided a reliable estimate of the ultimate tensile strength (UTS-like) of the alloy. Other indentation properties gave inconsistent results, and a post factum analysis was, therefore, conducted, by means of a new approach, to account for the presence of residual stresses. The already existing indentation data were supplemented with new repeated indentation tests to conduct a detailed analysis of the relaxation ability of compressive and tensile residual stresses. The developed methodology allows the effect of residual stresses and the reliability of measured macro-indentation properties to be examined as a function of a small group of indentation parameters.

The effect of curing regimes on the hydration products of lightweight ultra-high performance concrete: From experiments to MD simulations

The hydration products and microstructure of ultra-high performance concrete are influenced by the curing regime. In this study, the influence of curing regimes on the hydration products of lightweight UHPC was explored using experiments and molecular dynamics (MD) simulations. Experimental results show that the high temperature stimulates the pozzolanic activity of silica fume and fly ash promoting the hydration reaction of cement. AFt is decomposed to AFm under high temperature conditions, and the high temperature and high pressure promote C-A-S-H gel to transform into denser Tobermorite crystals. On this basis, the realistic molecular models of C-A-S-H gel corresponding to the hydration product of lightweight UHPC under different curing environments were established. The simulation results indicate that the mechanical properties of C-A-S-H were improved significantly after steam and autoclave curing compared with standard curing. The molecular models of lightweight UHPC exhibit an increased level of ductility and indentation modulus in comparison to ordinary Portland cement, which can be attributed to the inclusion of Al phase and a higher degree of silicate chain polymerization.