Increased Polyethylene Wear Research Articles

Cup positioning and its effect on polyethylene wear of vitamin E- and non-vitamin E-supplemented liners in total hip arthroplasty: radiographic outcome at 5-year follow-up

BackgroundAseptic loosening remains a challenging problem after total hip arthroplasty. Accurate cup placement and supplementation of antioxidants in acetabular liners might reduce material failure rates. The aim of this study is to assess the effect of the cup position on the wear behaviour of UHMWPE-XE and UHMWPE-X liners in vivo using virtual radiographs.MethodsWe conducted a prospective, randomized, controlled, multicenter trial. Clinical data of 372 probands were analyzed. Anteroposterior pelvic X-rays of 324 patients immediately postoperatively and after 1 and 5 years were evaluated by the RayMatch® analysis software regarding cup position and wear behaviour.ResultsMean cup anteversion was 20.3° (± 7.4) and inclination was 41.9° (± 7.0) postoperatively. 62.3% of all patients had an anteversion and inclination within the Lewinnek safe zone. Anterior and anterolateral approaches led to significantly higher cup anteversion compared to lateral approaches (27.3° ± 5.5; 20.9° ± 7.2; 17.5° ± 6.6; p < 0.001 and p = 0.001, respectively). Mean anteversion increased to 24.6° (± 8.0) after 1 year (p < 0.001). Only one revision occurred because of implant dislocation. Wear rates from UHMWPE-X and UHMWPE-XE did not differ significantly. Anteversion angles ≥ 25° correlated to increased polyethylene wear (23.7 µm/year ± 12.8 vs. 31.1 µm/year ± 22.8, p = 0.012) and this was amplified when inclination angles were ≥ 50° (23.6 µm/year ± 12.8 vs. 38.0 µm/year ± 22.7, p = 0.062).ConclusionAnterior approaches lead to the highest inaccuracy of cup placement, but cup positioning outside the Lewinnek safe zone does not necessarily cause higher dislocation rates. Moreover, mean anteversion increased by approximately four degrees within the first year after operation, which is expected to be functional due to a regularization of pelvic tilt after intervention. Mid-term wear rates of UHMWPE-X and UHMWPE-XE liners are comparable, but steep cup positions lead to significantly increased polyethylene wear. In summary, a re-evaluation of target zones for intraoperative cup positioning might be considered. In the long-term reduced oxidative embrittlement could lead to superior wear behaviour of vitamin E-blended liners.

Joint line elevation and tibial slope are associated with increased polyethylene wear in cruciate-retaining total knee replacement.

The purpose of this retrieval study was to determine the effect of implant positioning on wear, taking patient-related factors into account. Therefore, the volumetric material loss of 59 retrieved tibial liners was quantitatively determined using a coordinate measuring-machine. All retrievals were made of the same polyethylene and design by a single manufacturer. Using time in-situ and linear regression, a wear rate for each liner was determined and corrected for bedding-in. Backside damage was qualitatively scored. The following implant positioning parameters were obtained from radiographs: anatomical lateral-distal femoral angle, anatomical medial-proximal tibial angle, femoral tilt angle, and posterior tibial slope. The patella position was assessed by the Blackburne-Peel index and the Insall-Salvati ratio. Unlike the Insall-Salvati ratio, the Blackburne-Peel index is known to detect surgical joint line elevation. Using general linear modeling the most impactful factors on wear rate and backside damage was determined, thereby taking patient demographic factors into account. The mean volumetric wear rate was 11.6 mm3 /y. Wear decreased with older age (P = .021) and female sex (P = .001). The wear rate increased with joint line elevation as indicated from a decreased Blackburne-Peel index (P = .019), and increased with increased posterior tibial slope (P = .026). The backside damage score also increased with joint line elevation (P = .036). A Blackburne-Peel index decrease of 0.1, signifying joint line elevation, was found to increase the wear rate by 1.8 mm3 /y and increase back-sided wear. A high tibial slope (>7°) led to a 9.3 mm3 /y increase in wear rate compared with a low tibial slope (<3°). The results of this study demonstrate that tibial liner positioning has a significant impact on polyethylene wear with potential implications on osteolysis over time.

Higher Activity Level Following Total Knee Arthroplasty Is Not Deleterious to Mid-Term Implant Survivorship

BackgroundThe impact of a patient’s activity level following total knee arthroplasty (TKA) remains controversial, with some surgeons concerned about increased polyethylene wear, aseptic loosening, and revisions. The purpose of this study is to report on implant survivorship and outcomes of high activity patients compared to low activity patients after TKA. MethodsA retrospective review identified 1611 patients (2038 knees) that underwent TKA with 5-year minimum follow-up. Patients were divided in 2 groups based on their University of California Los Angeles (UCLA) activity level: low activity (LA) (UCLA ≤5) and high activity (HA) (UCLA ≥6). Outcomes included range of motion, Knee Society scores, complications, and reoperations. Parametric survival analysis was performed to evaluate the significance of activity level on survivorship while controlling for age, gender, preoperative pain, Knee Society clinical scores, Knee Society functional scores, and body mass index (BMI). ResultsMean follow-up was 11.4 years (range 5.1-15.9). The LA group had significantly more female patients, were older, had higher BMI, and had lower functional scores preoperatively (all with P < .001). The HA group had significantly higher improvements in Knee Society scores (P < .001) and pain postoperatively (P < .001). Revisions were performed in 4% of the LA group and 1.7% knees of the HA group (P = .003). After controlling for age, gender, preoperative pain, Knee Society clinical scores, Knee Society functional scores, and BMI, a higher postoperative activity level remained a significant factor for improved survivorship with an odds ratio of 2.4 (95% confidence interval 1.2-4.7, P = .011). The all-cause 12-year survivorship was 98% for the HA group and 95.3% for the LA group (P = .003). The aseptic 12-year survivorship was 98.4% for the HA group and 96.3% for the LA group (P = .02). ConclusionHighly active patients had increased survivorship at 5-year minimum follow-up compared to lower activity patients after TKA. Patient activity level after TKA may not need to be limited with modern implants.

Evaluation of Surface Finish and Dimensional Control of Tribological Metal-Ultra High Molecular Weight Polyethylene Pair of Commercially Available Hip Implants

BackgroundDimensional control and surface finish of the femoral head and acetabular liner are critical factors in the manufacturing process due to the risk of increased polyethylene wear, which is the primary cause of aseptic failure of a metal/polymer hip prosthesis. The aim of this study is to perform a dimensional and surface finish analysis to evaluate the reproduction and accuracy of the manufacturing processes of metal femoral heads and ultra high molecular weight polyethylene acetabular liners. MethodsFour femoral heads and acetabular liners from 5 manufacturers were evaluated. The methods of evaluation followed the standards ISO 7206-2:2011 and ISO 21535:2010. ResultsThe diameter, sphericity, and roughness of the femoral heads from all the manufacturers were in accordance with the standard requirements. Only the sphericity showed a lack of repeatability among the manufacturers. The variability in sphericity was high among some manufacturers and low in others. The diameters of the acetabular liners of 2 manufacturers were not in accordance with the standard requirements. The repeatability of sphericity, thickness, and roughness of the acetabular liners were heterogeneous among the manufacturers, which means that some manufacturers need to improve quality control. ConclusionOur results showed a good dimensional and surface finish control of the manufacturing processes of the femoral heads. However, the same control was not shown during the manufacturing of the acetabular liners although all samples had a thickness and sphericity in accordance with the standard. A better quality control of the manufacturing process of ultra high molecular weight polyethylene acetabular liners should be made to improve the dimensional parameters of the acetabular liners and the tribological pair.

No Difference in Conventional Polyethylene Wear Between Yttria-stabilized Zirconia and Cobalt-chromium-molybdenum Femoral Heads at 10Years.

Concerns have arisen regarding deterioration of wear properties of yttria-stabilized zirconia (YSZ) femoral head on conventional polyethylene (PE) bearings due to YSZ phase transformation. The purpose of this study was to determine if there is a difference in long-term PE wear properties between YSZ and cobalt-chromium-molybdenum (Co-Cr-Mo) femoral heads. Ten-year radiographic wear assessment was performed on a cohort of patients enrolled in a prospective randomized clinical trial comparing total hip arthroplasty with YSZ or Co-Cr-Mo femoral heads on conventional, non-cross-linked PE. PE linear wear, annualized wear, and steady-state wear rates remained low and similar between groups. No cases of osteolysis were observed. Measured conventional PE wear was similar between YSZ and Co-Cr-Mo femoral heads with the steady-state wear rates for both remaining below the generally accepted threshold at which osteolysis typically occurs. Whether clinically relevant phase transformation with YSZ femoral heads occurs is uncertain; however, the use of YSZ femoral heads in this study was not associated with increased PE wear, osteolysis, or deterioration of wear properties.

Salvage of a monoblock metal-on-metal cup using a dual mobility liner: a two-year MRI follow-up study.

Revision of failed modular metal-on-metal total hip replacement (MoM-THA) can be technically difficult. A dual mobility liner can help to salvage a well-fixed acetabular component. The present paper reports the clinical and radiographic outcome of revision of failed Birmingham modular MoM-THA using a dual mobility liner. The present study reports on ten patients (3 female and 7 male) with 11 revision THAs. Patients underwent revision an average of 51months (range 40-73months) after index procedure. Mean follow-up after the revision was 31months (range 24-37months) and all patients underwent an MRI with metal artifact reduction software (MARS) at least twoyears after revision to assess for local polyethylene wear and osteolysis. The Harris Hip score improved from 92.2 (range 63.0-100.0) to 100.0 (p=0.072). One patient had a one-time dislocation within sevendays of surgery. No patient required additional surgeries. Radiographs showed no signs of component loosening and osteolysis and MRI imaging revealed no evidence of polyethylene wear or osteolysis. A dual mobility liner in an existing Birmingham cup can provide excellent clinical and radiological short-term results without MRI evidence of increased polyethylene wear. Post-operative hip precautions should be enforced.

Neer Award 2017: wear rates of 32-mm and 40-mm glenospheres in a reverse total shoulder arthroplasty wear simulation model

Larger glenosphere diameters have been used recently to increase prosthesis stability and impingement-free range of motion in reverse total shoulder arthroplasty. The goal of this study was to evaluate the rate of polyethylene wear for 32-mm and 40-mm glenospheres. Glenospheres (32 mm and 40 mm, n = 6/group) and conventional polyethylene humeral liners underwent a 5-million cycle (MC) wear simulation protocol. Abduction-adduction and flexion-extension motion profiles were alternated every 250,000 cycles. At each interval, mass loss was determined and converted to volume loss and wear rate. At 0, 2.5 MC, and 5 MC, liners were imaged using micro-computed tomography to determine surface deviation. White light interferometry was performed on liners and glenospheres at 0 and 5 MC to quantify surface roughness. Wear particle morphology was characterized by environmental scanning electron microscopy. Total volume loss was significantly higher in 40-mm liners from 1.5 MC onward (P < .05). Overall, volumetric wear rate was significantly higher in 40-mm liners compared with 32-mm glenospheres (81.7 ± 23.9 mm3/MC vs. 68.0 ± 18.9 mm3/MC; P < .001). However, micro-computed tomography surface deviation results demonstrated increased linear penetration on 32-mm glenospheres compared with 40-mm glenospheres (0.36 ± 0.03 µm vs. 0.28 ± 0.01 µm; P = .002). Surface roughness measurements showed no difference for liners; however, increased roughness was noted for 40-mm glenospheres at 5 MC compared with 32 mm (P < .05). Larger glenospheres underwent significantly greater polyethylene volume loss and volumetric wear rates, whereas smaller glenospheres underwent greater polyethylene surface deviations. The enhanced stability provided by larger glenospheres must be weighed against the potential for increased polyethylene wear.

Equivalent wear performance of dual mobility bearing compared with standard bearing in total hip arthroplasty: in vitro study

Osteolysis in total hip arthroplasty (THA) depends on polyethylene wear and dictates the survival of the prosthesis. Dual mobility in THAs, which is claimed to reduce dislocation risk, has very good long-term clinical results. However, little is known about how the liner wears in this design, compared to the standard single mobility model. A comparative study looking at wear of a conventional ultra-high-molecular-weight polyethylene liner, using gravimetric measurement, between dual mobility implants and standard implants, was performed on a simulator in accordance with a normed protocol based on the same dimensions, environmental conditions and stresses. A linear regression test was employed. Under the same conditions (loading, cycles, sterilization, material and surface roughness), the gravimetric wear (for conventional polyethylene) is comparable between a standard and a dual mobility cup. This correlates to ten year follow-up results of dual mobility cup. This in vitro equivalent wear serves to confirm the very good long-term clinical results observed with dual mobility bearing, whose use should not be restricted by concerns about increased polyethylene wear.

The increase in cobalt release in metal-on-polyethylene hip bearings in tests with third body abrasives.

Hypersensitivity reactions in patients receiving metal-on-metal hip replacements have been attributed to corrosion products as observed by elevated cobalt and chromium ions in the blood. Although the majority of cases are reported in metal-on-metal, incidences of these reactions have been reported in the metal-on-polyethylene patient population. To date, no in vitro study has considered cobalt release for this bearing combination. This study considered four 28 mm and seven 52 mm diameter metal-on-polyethylene bearings tested following ISO standard hip simulator conditions as well as under established abrasive conditions. These tests showed measurable cobalt in all bearings under standard conditions. Cobalt release, as well as polyethylene wear, increased with diameter, increasing from 52 to 255 ppb. The introduction of bone cement particles into the articulation doubled polyethylene wear and cobalt release while alumina particles produced significant damage on the heads demonstrated by cobalt levels of 70,700 ppb and an increased polyethylene wear from a mean value of 9–160 mm3/mc. Cobalt release was indicative of head damage and correlated with polyethylene wear at the next gravimetric interval. The removal of third body particles resulted in continued elevated cobalt levels in the 52 mm diameter bearings tested with alumina compared to standard conditions but the bearings tested with bone cement particles returned to standard levels. The polyethylene wear in the bone cement tested bearings also recovered to standard levels, although the alumina tested bearings continued to wear at a higher rate of 475 mm3/mc. Cobalt release was shown to occur in metal-on-polyethylene bearings indicating damage to the metal head resulting in increased polyethylene wear. While large diameter metal-on-polyethylene bearings may provide an increased range of motion and a reduced dislocation risk, increased levels of cobalt are likely to be released and this needs to be fully considered before being widely adopted.

Is Cup Positioning Challenged in Hips Previously Treated With Periacetabular Osteotomy?

After periacetabular osteotomy (PAO), some patients develop osteoarthritis with need of a total hip arthroplasty (THA). We evaluated the outcome of THA following PAO and explored factors associated with inferior cup position and increased polyethylene wear. Follow-up were performed 4 to 10years after THA in 34 patients (38 hips) with previous PAO. Computer analysis evaluated cup position and wear rates. No patient had dislocations or revision surgery. Median scores were: Harris hip 96, Oxford hip 38 and WOMAC 78. Mean cup anteversion and abduction angles were 22o (range 7°–43°) and 45° (range 28°–65°). Outliers of cup abduction were associated with persisting dysplasia (CE <25°). THA after PAO can produce excellent clinical results. Persisting acetabular dysplasia following PAO may lead surgeons to place the acetabular component in excessive cup abduction, and this tendency should be recognized at the time of the PAO.

What are the Predictors for Bead Shedding in Porous-Coated Hip and Knee Arthroplasties?: An Implant Retrieval Study

Bead shedding has been reported in both hip and knee arthroplasties and can result in increased polyethylene wear and metal ion release. The rates of bead loss were recorded for each device type, and the interfacial bead-substrate shear load to failure and contact areas of the beads were determined. The 3 components with the highest rate of bead loss, namely, S-Rom, Omnifit, and Optifix acetabular shells, recorded the lowest shear loads to failure. Percentage bead-substrate contact area ranged between 7% and 37% and was the most important factor affecting bead shedding. Other factors influencing bead loss in decreasing order of importance were bead fusion, bead size, component type (acetabular or knee), component loosening, and time in situ.

Wear simulation of reverse total shoulder arthroplasty systems: effect of glenosphere design

Although early results with reverse total shoulder arthroplasty (rTSA) have been promising, concern exists about the high reported rates of scapular notching and the potential for catastrophic failure of glenoid component fixation. Generation of polyethylene wear debris may also contribute to notching and osteolysis of the scapula. A testing model for polyethylene wear is currently unavailable for reverse shoulder prostheses. The goal of this study was to develop a testing protocol using a commercially available hip simulator. Component design may also influence the generation of polyethylene debris. It is hypothesized that increased polyethylene wear occurs in glenospheres with holes in the articulating surface. Custom fixtures were fabricated to simulate both glenohumeral abduction and flexion on a 12-station hip wear simulator. Loading profiles for both abduction and flexion were alternated every 250,000 cycles for a total of 5 million cycles. Gravimetric analysis of humeral cups throughout the test was used to characterize wear. Lubricant fluid was collected throughout the test and digested for polyethylene particle analysis. Comparisons of volumetric wear rates and total volume loss between glenospheres with and without holes and between flexion and abduction loading profiles showed similar results. Particle analysis displayed fibrillar particles with an equivalent circle diameter of 0.3 ± .1 μm and an aspect ratio of 2.5±1.4. This study represents the first wear simulation and particle characterization of reverse shoulder systems. No significant difference in wear was reported between glenospheres with and without holes.

Superior 11-Year Survival but Higher Polyethylene Wear of Hydroxyapatite-Coated Mallory-Head Cups

Hydroxyapatite (HA) coating of implant surfaces is believed to improve longevity of uncemented total hip arthroplasty (THA). However; it is speculated that HA particles may cause third body wear of the polyethylene (PE) liner with subsequent osteolysis and aseptic loosening of implants. We performed a retrospective comparison of two patient populations with cementless Mallory-Head acetabular components. The patients were identified in the Danish hip arthroplasty Registry (DHR); 77 patients had HA-coated cups and 73 patients had non-HA coated cups. Anteroposterior (AP) radiographs were analysed for PE wear, osteolysis was quantified and survival of the acetabular components was compared. The mean follow-up was 11 years. There were no cup revisions in the HA group and 7 cup revisions in the non-HA group (P<0.01). The reason for revision in all cases was aseptic loosening of both stem and cup. The amount of osteolysis was significantly increased around cups in the non-HA group. The two-dimensional linear PE wear-rate of 0.18 mm/year was higher (P<0.001) in the group with HA coated cups compared with 0.12 mm/year in the group with non-HA coated cups. The mean age was lower (P=0.001) in the HA group (57 years) compared with the non-HA group (63 years). After 11.1 years of follow-up non-HA coated cups had a higher revision rate. Increased PE wear with HA-coated cups did not have a negative influence on the revision rate, but may result in a need for revision surgery over time.

All-Polyethylene Tibial Components in Obese Patients Are Associated With Low Failure at Midterm Followup

In the United States, the obese population has increased markedly over the last four decades, and this trend continues. High patient weight places additional stress on TKA components, which may lead to increased polyethylene wear, osteolysis, radiolucencies, and clinical failure. Metal-backed tibial components and all-polyethylene tibial components in the general population have comparable osteolysis and failure, but it is unclear whether these components yield similar osteolysis and failure in obese patients. We therefore determined the (1) function, (2) occurrence of osteolysis, and (3) complications in a cohort of obese patients receiving all-polyethylene tibial components. Between September 17, 1996, and December 19, 2002, we implanted all-polyethylene tibial components in 90 obese patients (125 knees); 24 patients (33 knees) died and 13 patients (17 knees) were lost to followup, leaving 53 patients (59%) with 75 knees. All surgeries were cruciate-retaining, tricompartmental TKAs. We evaluated patients with Knee Society Scores and serial radiographs. Minimum followup was 7 years (mean, 10.4 years; range, 7-14 years). At latest followup, mean Knee Society Score was 92 points. There were five tibial radiolucencies, all less than 1 mm and characterized as nonprogressive. We observed minimal, nonprogressive osteolysis in one knee. One patient required reoperation after a traumatic event. There were no implant-related failures and no implants at risk of failure. At an average 10-year followup, all-polyethylene tibial components were functioning well in this obese group. These findings confirm the effectiveness of all-polyethylene tibial components in obese patients.

Cemented Total Hip Replacement Cable Debris and Acetabular Construct Durability

Third-body wear can adversely affect the outcome of total hip arthroplasty by causing increased polyethylene wear, osteolysis, and component loosening. We hypothesized that there would be greater generation and migration of metal debris to the bearing surfaces in hips in which cobalt-chromium cables were used to reattach the osteotomized greater trochanter when compared with hips in which stainless steel wires were used. Between June 1981 and December 1983, 196 consecutive total hip arthroplasties were performed with use of an Iowa stem and a titanium-backed cemented acetabular component, with cobalt-chromium cable trochanteric reattachment. After nineteen to twenty years of follow-up, the patients were evaluated with regard to the depth of head penetration into the polyethylene (as a surrogate for wear), osteolysis, loosening, and the need for revision. The results were compared with those for a series of 304 total hip arthroplasties that were performed by the same surgeon from January 1984 to December 1985 with use of the same components and the same surgical technique, but with stainless steel wire trochanteric reattachment. The two groups had a comparable nineteen to twenty-year follow-up. All living patients (fifty-nine hips in the cable group and ninety-two hips in the wire group) had minimum ten-year follow-up radiographs. The polyethylene wear rate was 0.101 mm/yr for the cable group and 0.082 mm/yr for the wire group (p = 0.039). For the living patients, the rate of revision of the acetabular component because of aseptic loosening was 37.3% (twenty-two hips) for the cable group and 20.7% (nineteen hips) for the wire group (p = 0.025). The rate of acetabular osteolysis was 44% (twenty-six hips) for the cable group and 26% (twenty-four hips) for the wire group (p = 0.022). Kaplan-Meier analysis with revision of the acetabular component because of aseptic loosening as the end point demonstrated survival rates of 73.7% +/- 9% and 83% +/- 7% for the cable and wire groups, respectively, at twenty years (p = 0.03). Because cable trochanteric attachment led to significantly greater polyethylene wear, osteolysis, acetabular loosening, and acetabular revision, presumably due to third-body metallic debris generation in this cemented total hip replacement construct, surgeons should be aware of the deleterious effects of third-body debris and avoid the use of potential debris generators in the total hip arthroplasty construct. If cable is used and fretting is recognized, especially with intra-articular migration of metallic material or nonunion of the greater trochanter, consideration should be given to cable removal.

Surface Roughness of CoCr and ZrO2 Femoral Heads with Metal Transfer: A Retrieval and Wear Simulator Study

Metal transfer to femoral heads may result from impingement against the metallic acetabular shell following subluxation/dislocation, or when metallic debris enters the articulation zone. Such transfers roughen the head surface, increasing polyethylene wear in total hip replacements. Presently, we examined the surface roughness of retrieved femoral heads with metallic transfer. Profilometry revealed roughness averages in regions of metal transfer averaging 0.380 μm for CoCr and 0.294 μm for ZrO2 which were one order of magnitude higher than those from non-implanted controls. Scanning electron microscopy (SEM) revealed adherent transfers on these retrievals, with titanium presence confirmed by electron dispersive spectroscopy. Due to the concern for increased wear, metal transfer was induced on non-implanted heads, which were then articulated against flat polyethylene discs in multidirectional sliding wear tests. Increased polyethylene wear was associated with these specimens as compared to unaltered controls. SEM imaging provided visual evidence that the transfers remained adherent following the wear tests. Pre- and post-test roughness averages exceeded 1 μm for both the CoCr and ZrO2 heads. Overall, these results suggest that metal transfer increases the surface roughness of CoCr and ZrO2 femoral heads and that the transfers may remain adherent following articulation against polyethylene, leading to increased polyethylene wear.

Unterschiede des Polyäthylenabriebs bei Hüftgelenkendoprothesen mit Keramik-und Metall-Polyäthylenpaarung der Gleitflächen

Pseudocapsules of artificial hip joints with ceramic- and metal on polyethylene combination of the articulating surfaces from 126 revision arthroplasties and 41 autopsies were studied histologically with semiquantitative evaluation of the polyethylene wear. The results were compared with reports of laboratory tests in the literature. We found in the autopsy specimens as well as in the biopsies from revision arthroplasties of prostheses implanted for 4 to 8 years three times less polyethylene wear particles released from the ceramic on polyethylene prostheses. The newly established synovium surrounding prostheses with ceramic heads appeared 20% reduced in thickness with minor villous transformation. Different types of metal on polyethylene prostheses revealed no differences in wear behaviour with the exception of the bipolar prostheses which showed a markedly increased polyethylene wear.

Trochanteric non-union—Does it influence the rate of revision following primary total hip replacement? A minimum of 15 years follow-up

Trochanteric non-union may alter the biomechanics and the forces going through the hip joint leading to increased polyethylene wear and hence a higher revision rate. The aim of our study was to determine if trochanteric non-union was associated with a higher incidence of acetabular and/ or femoral revision for mechanical failure, i.e. aseptic loosening. Three hundred and twenty-six total hip replacements performed in 318 patients between 1979 and 1989 were reviewed. The status of the trochanter was determined using the senior author's (JPH) classification of trochanteric union/non-union. The mean follow-up was 16.7 years (15-25 years). 20.5% (61/297) of hips with united trochanter and 20.6% (6/29) with un-united trochanter had been revised at the latest follow-up. The difference was not significant (p-value > 0.1, odds ratio 1.01). We could not find any influence of trochanteric non-union on acetabular or femoral revision rate over a mean follow-up period of 17 years (range 15-25 years).

Knieprothesenkinematik

Until now it remains less clear to what extent the different types of endoprostheses can simulate the physiological motion pattern of the knee joint. The aim of this study was to present fluoroscopy and functional MRI as well as the results of these in vivo imaging techniques for TKA kinematics. Videofluoroscopy is a dynamic investigation, analyzing the subjects under fluoroscopic surveillance during different activities. Three-dimensional (3D) kinematics were recovered from the two-dimensional fluoroscopic images using a model-fitting technique. Kinematic analysis with functional MRI was performed in an open MR system at different flexion angles with external loads being applied during imaging. Femoropatellar and femorotibial 3D kinematics were analyzed by image postprocessing. The findings in healthy knees obtained with functional MRI under static conditions are in good agreement with the fluoroscopic outcome under dynamic conditions. In all investigated TKA in the mean an increased external rotated position of the femur relative to the tibia was observed at full extension, while the amount of external rotation during knee flexion was decreased. Although there was great variability among the individuals, differences were observed between the TKA-groups (e.g. posterior stabilized vs PCL retaining). Significant changes of femorotibial and femoropatellar kinematics were found in TKA compared to healthy knees, which may lead to early aseptic loosening or increased polyethylene wear The presented techniques and results allow for advanced in vivo diagnostics and may help to improve the design of TKA and to enhance the long-term performance.

Increased polyethylene wear after cementless ABG I total hip arthroplasty

The cementless, hydroxyapatite-coated Anatomique Benoist Giraud-I (ABG-I) hip endoprosthesis represented a modern implant in the 1990s. The aim of the current retrospective study was to evaluate the clinical and radiological results of this prosthesis. In addition, an analysis of the complications and retrieved implants was conducted. The medium-term results (follow-up 5.23 years) of 193 hip joints are presented. Of 158 total cohorts, 81.9% was able to undergo follow-up performed with standardized clinical and radiological investigations. Physical characteristics of the patients and the underlying disease prompting the need for total hip arthroplasty, as well as a clinical score (Merle d'Aubigné) were recorded. At the time of follow-up, a radiologic examination of all patients with a standardized evaluation was performed. In addition, the migration of the acetabular cup and femoral head as well as polyethylene wear could be determined digitally in 118 cases (61.1%) using one-picture Roentgen analysis. Clinical results, as measured with a Merle d'Aubigné Score increase from 8.4 to 16.2, were very good. Radiographs demonstrated successful osseous integration of the anatomically molded shaft. Within the period of the investigation, no revision procedures of the femoral shaft were necessary. However, the rate of polyethylene abrasion of 0.23 mm/year was markedly high. 13.9% of hips (n = 27) required acetabular cup revision due to wear. This calculates to a prosthesis 7-year survival probability of 63%. Intraoperative findings during the revision cases showed extensive periacetabular osteolysis with foreign body granulation tissue. Analysis of data from the total patient cohort versus data from cases requiring revision showed a significantly increased frequency of high polyethylene wear in young active patients as well as in cases where an unfavorable acetabular cup to femoral head relation existed in correspondence with polyethylene thickness. There is evidence, however, that suggests that multifactorial causes for the increased wear are significant in regards to the principal material and technical features of the prosthesis. On the basis of these results, it is strongly recommended that all patients treated with an ABG-I hip endoprosthesis should receive close clinical and most importantly close radiologic follow-up.