Increase In Load Research Articles

Experimental study of low temperature plasma synergistic catalyst for treatment of DEP in water

In this paper, CuO/Al2O3 catalysts were prepared by impregnation method, and the catalysts were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) techniques. The effects of loading capacity and roasting temperature on the performance of CuO/Al2O3 synergistic low-temperature plasma degradation of DEP in water were investigated during the catalyst preparation process, and the influences of the catalyst dosage, input voltage in the synergistic system, aeration flow rate, and the initial concentration of the reactants on the removal effect of DEP were also explored. The results showed that the removal rate of DEP by the synergistic system tended to increase and then decrease with the increase of catalyst loading and roasting temperature. The degradation rate of DEP could reach 94.08 % under the optimal conditions of 400 °C, 30 % catalyst loading, concentration of 10 mg/L, input voltage of 30 kV, and aeration flow rate of 200 L/h. And the degradation pathway of DEP was inferred by mass spectrometry detection.

Particle Dynamics In T-Junction High-Concentration Flow

The work describes sand-particle high-Reynolds number flow in a Tjunction. Experiments are carried out for one different Reynolds number (Re = 9.5x104), one typical particle diameter distribution (Mesh 150) and four sand concentrations (0.05, 0.1, 0.6 and 1.1 % w/w). The purpose of the work is to characterize the effects of indirect particle-to-particle interaction as particle load increases. PTV and PIV measurements are used to discriminate the velocities of the particles and the carrier fluid. The results shown that rebounding effects have a significant influence on particle dynamics.

Assessing Particulate Emissions of Novel Synthetic Fuels and Fossil Fuels under Different Operating Conditions of a Marine Engine and the Impact of a Closed-Loop Scrubber

Particle emissions from marine activities next to gaseous emissions have attracted increasing attention in recent years, whether in the form of black carbon for its contribution to global warming or as fine particulate matter posing a threat to human health. Coastal areas are particularly affected by this. Hence, there is a great need for shipping to explore alternative fuels that both reduce greenhouse gas emissions, as anticipated through IMO, and also have the potential to reduce particle emissions significantly. This paper presents a comparative study of the particulate emissions of two novel synthetic/biofuels (GTL and HVO), which might, in part, substitute traditionally used distillate liquid fuels (e.g., MDO). HFO particulate emissions, in combination with an EGCS, formed the baseline. The main emphasis was laid on particle concentration (PN) and particulate matter (PM) emissions, combining gravimetric and particle number measurements. Measurements were conducted on a 0.72 MW research engine at different loads (25%, 50%, and 75%). The results show that novel fuels produce slightly fewer emissions than diesel fuel. Results also exhibit a clear trend that particle formation decreases as engine load increases. The EGCS only moderately reduces particle emissions for all complaint fuels, which is related to the formation of very fine particles, especially at high engine loads.

Investigation on tribological behaviors of a novel generation polymer-coated ceramsite particle for fracturing

During fracturing, proppant particles can create favorable pathways for shale gas production. To solve the problem of low production efficiency of shale gas, a new polymer coated particle was prepared by experiment. And its mechanical properties were tested and tribological properties were studied under different speeds, loads and medium states. The results show that the new polymer coated particles have excellent tribological and mechanical properties. The friction coefficient between proppant particles and fracture surface decreases with increasing velocity. In addition, the new proppant particles have excellent hydrophobicity under lubricating conditions, indicating that the proppant has excellent migration efficiency. When proppants just pumped into the fracture, it can reach the fracture depth quickly. In addition, the friction coefficient between proppant particles and fracture surface gradually increases with the increase of load. It is further proved that when the proppant particles enter the fracture, the friction coefficient increases due to the extrusion of the fracture, and the reverse displacement can be effectively reduced. This research has important theoretical and practical engineering application value for improving the efficiency of shale gas stimulation.

Finding a closest saddle–node bifurcation in power systems: An approach by unsupervised deep learning

We propose a neural network using an unsupervised learning strategy for direct computation of closest saddle–node bifurcations, eliminating the need for labeled training data. Our method not only estimates the worst-case load increase scenarios but also significantly reduces the computational complexity traditionally associated with this task during inference time. Simulation results validate the effectiveness and real-time applicability of our approach, demonstrating its potential as a robust tool for modern power system analysis.

Effect of Training Load Intensification on the Sleep Pattern of Young Soccer Players

ABSTRACT Purpose: The aim of this study was to examine how intensifying training loads over a week affects the sleep patterns of young soccer players on the nights immediately following the intensified training sessions. Methods: Quasi-experimental study. Fifteen young athletes participants of a team engaged in national level competition, underwent two weeks of training with varying load magnitudes—Week 1: low accumulated training load and Week 2: intensified training loads [40% increase in external training load(ETL)]. To characterize the intensification of the workload, the methods PlayerLoad and RPE-Session were employed to measure ETL and internal training load(ITL), respectively. Total sleep time(TST), total time in bed(TTB), sleep efficiency(SE), sleep latency(SL), and wake after sleep onset(WASO) were obtained using actigraphy and daily sleep log. The variables were compared among the days of week (e.g. Monday of week 1 with Monday of week 2, and so forth). Results: Acute training intensification in week 2 led to significant increases in ETL and ITL on Monday and on Wednesday(p < .05), and ETL(p < .05) on Friday on the second week. Improvements in sleep were observed (Tuesday—TST:+80 min, WASO:-29.3 min, SL:-8 min, SE:+9%; Thursday—TST:+86 min, SL:-4 min, SE:+4%; Saturday—TST:+40 min, SL:+1 min) compared to the same day of the previous week. Correlations between ETL and ITL(r = 0.637), ITL and TST(r = 0.572), ITL and SE(r = 0.548) were found. Conclusion: Intensification of training loads results in alterations in sleep variables, notably an elevated TST and SE in the days subsequent to the acute load increment.

Comparative analysis of the microbiota of prostate secretion in patients with chronic abacterial prostatitis of categories IIIa and IIIb

Numerous studies have established that chronic prostatitis/ chronic pelvic pain syndrome ( CP/CPPS) is the focus of attention of the global medical community, because it is the most common type of disease, the treatment of which has largely unsatisfactory results.Purpose of the work: to conduct a comparative analysis of the microbiota of prostate secretions in patients with CP/CPPS IIIa and IIIb using mass spectrometry of microbial markers (MSMM).Material and methods. A prospective comparative study was conducted from 2018 to 2023 at the SM-Clinic medical center. 205 patients with prostatitis-like symptoms and 70 males who applied for a screening examination with no complaints at the age of 25 to 50 years were selected. The subjects were divided into three groups: group 1 – patients with CP/CPPS category IIIa, group 2 ( n = 85) patients with CP/CPPS category IIIb with clinical manifestations of chronic prostatitis and group 3 ( n = 70) – without clinical manifestations prostatitis/control group. A study of the microbiota of prostate secretions was carried out using gas chromatograph mass spectrometer "Maestro" (LLC "Interlab", Russia).Results. The results of statistical analysis showed that the level of cocci and bacilli, anaerobes, actinobacteria, fungi and yeasts, as well as total viruses in patients with CP/CPPS IIIa, compared with patients with CP/CPPS IIIb and the control group, was significantly higher ( p = 0.0020 ; p &lt; 0.0001; p &lt; 0.0001; p = 0.0254; p = 0.0254). It was revealed that in patients with CP/CPPS IIIa, compared with patients with CP/CPPS IIIb and healthy people, there was a significant increase in the total load of cocci and bacilli, anaerobes, actinobacteria, fungi and yeasts, as well as total viruses . When analyzing the relationship between the absolute number of microorganisms, it was revealed that an increase in the level of many microorganisms is associated with an increase in the probability of detecting a leukocyte level 10. An analysis of the relationship between the occurrence of individual microorganisms and leukocyte values in prostate secretions ≥10 showed that an increase in the indicators of many microorganisms, compared with the control group, increased the chances of having a leukocyte level ≥10 several times.Conclusion. Identification of microbial associations in prostate secretions using the MSMM method and an increase in the total load of microorganisms in patients with CP/CPPS IIIa, compared with CP/CPPS IIIa and the control group, suggests the role of infection in a certain part of patients with CP/CPPS IIIa, which dictates the need to change the view of the urologist in the diagnosis and treatment strategy of these patients.

Conservation genomics of the critically endangered Chinese pangolin.

The Chinese pangolin (Manis pentadactyla, MP) has been extensively exploited and is now on the brink of extinction, but its population structure, evolutionary history, and adaptive potential are unclear. Here, we analyzed 94 genomes from three subspecies of the Chinese pangolin and identified three distinct genetic clusters (MPA, MPB, and MPC), with MPB further divided into MPB1 and MPB2 subpopulations. The divergence of these populations was driven by past climate change. For MPB2 and MPC, recent human activities have caused dramatic population decline and small population size as well as increased inbreeding, but not decrease in genomic variation and increase in genetic load probably due to strong gene flow; therefore, it is crucial to strengthen in situ habitat management for these two populations. By contrast, although human activities have a milder impact on MPA, it is at high risk of extinction due to long-term contraction and isolation, and genetic rescue is urgently needed. MPB1 exhibited a relatively healthy population status and can potentially serve as a source population. Overall, our findings provide novel insights into the conservation of the Chinese pangolin and biogeography of the mammals of eastern Asia.

Bond behaviour of prestressed basalt textile reinforced concrete

Innovative Textile Reinforced Concrete (TRC) composites, although holding a significant potential, usually have poor performance under serviceability conditions. Addressing this limitation requires applying innovative techniques, such as prestressing, to utilise its potential fully. However, successful design and application of prestressing require a comprehensive understanding of the prestressing effect across scales, including the textile-to-matrix bond behaviour. To address this need, this study investigated the influence of key parameters such as prestressing level, prestressing release time and matrix age on the bond behaviour of basalt textile reinforcement. Test results show a significant influence of prestressing level and release time on textile-matrix bond behaviour. A 1-day prestressing release time resulted in a 25 % increased stiffness with only a 5 % peak load reduction followed by a further 13.7 % increase in the pull-out energy when the prestressing level was 13 %. At 35 % prestress level, 1-day released samples showed a significant reduction of 48.4 % in the peak load and 76 % reduction in the debonding energy. The positive effect of prestressing on the bond behaviour became more evident at prolonged release durations. The 7-day release samples showed a 17.4 % increase in the peak load at both prestress levels. Meanwhile, at 35 % prestress level, 34 % further increase in the debonding energy was observed. The obtained data are then utilised for providing indications on the effect of prestressing on saturated crack spacing of TRC components.

Research on the Blades and Performance of Semi-Submersible Wind Turbines with Different Capacities

With the gradual increase in the maturity of wind energy technology, floating offshore wind turbines have progressively moved from small-capacity demonstrations to large-capacity commercial applications. As a direct component of wind turbines used to capture wind energy, an increase in the blade length directly leads to an increase in blade flexibility and a decrease in aerodynamic performance. Furthermore, if the floater has an additional six degrees of freedom, the movement and load of the blade under the combined action of wind and waves are more complicated. In this work, two types of semi-submersible wind turbines with different capacities are used as the research objects, and the load and motion characteristics of the blades of these floating offshore wind turbines are studied. Through the analysis of the simulation data, the following conclusions are drawn: with the increase in the capacity of the wind turbine, the flexible deformation of the blade increases, the movement range of the blade tip becomes larger, the blade root load increases, and the power fluctuation is more obvious. Compared with the bottom-fixed wind turbine, the flexible blade deformation of the floating offshore wind turbine is smaller; however, the blade root load is more dispersed, and the power output is more unstable and lower.

TTV and CMV viral load dynamics: Which emerges first during immunosuppression?

Novel biomarkers reflecting the degree of immunosuppression in transplant patients are required to ensure eventual personalized equilibrium between rejection and infection risks.With the above aim, Torque Teno Virus(TTV) viremia was precisely examined in a large cohort of transplanted immunocompromised patients (192 hematological and 60 solid organ transplant recipients) being monitored for Cytomegalovirus reactivation.TTV load was measured in 2612 plasma samples from 448 patients. The results revealed a significant increase in TTV viral load approximately 14 days following CMV reactivation/infection in solid organ transplant(SOT) patients. No recognizable difference in TTV load was noted among hematological patients during the entire timeframe analyzed. Furthermore, a temporal gap of approximately 30 days was noted between the viral load peaks reached by the two viruses, with Cytomegalovirus(CMV) preceding TTV.It was not possible to establish a correlation between CMV reactivation/infection and TTV viremia in hematological patients. On the other hand, the SOT patient cohort allowed us to analyze viral kinetics and draw intriguing conclusions. Taken together, the data suggest, to our knowledge for the first time, that CMV infection itself could potentially cause an increase in TTV load in the peripheral blood of patients undergoing immunosuppressive therapy.

Effectiveness of Grouting and GFRP Reinforcement for Repairing Spalled Reinforced Concrete Beams

Corrosion of steel reinforcement from chloride exposure can compromise the strength of reinforced concrete structures. Rust formation expands, applying pressure on concrete, resulting in cracks and spalling. Prompt repair is crucial for severe cases of spalling. This research assessed the efficacy of repair strategies for reinforced concrete beams post-spalling, including grouting and different techniques involving Glass Fiber Reinforced Polymer (GFRP) reinforcement. The research examined four variations of reinforced concrete beams, each sized at 150 mm × 200 mm × 3300 mm. Results showed that the standard beam (BK) had an average maximum load capacity of 29.74 kN. In contrast, the grouted beam (BGR) demonstrated a reduced maximum load of 14.39 kN, along with decreased steel and concrete strain compared to BK. This suggests that the grouting repair did not fully restore the beam's flexural capacity after spalling. Incorporating GFRP strips (BGRS) led to a marginal increase in the beam's maximum load, albeit remaining below BK, with lower steel and concrete strain than BK. However, the steel and concrete approached their yield points, indicating enhanced flexural performance. The full-wrap GFRP beam (BGRSF) experienced an 8.08% increase in maximum load compared to BK, with concrete strain surpassing BK, suggesting an enhancement in flexural stiffness. Doi: 10.28991/CEJ-2024-010-07-05 Full Text: PDF

Effect of the Ni plating on Al–Cu dissimilar metal laser welded joint

In this study, the joint strength and interfacial microstructure of Al–Cu laser welded joints are investigated to understand the effect of Ni plating. Cu without plating and Cu plated with 1 μm and 4 μm of Ni were laser welded with Al, respectively, and their differences in joint strength and microstructure were comparatively analyzed. Macrostructure observations showed that the plating had no effect on the change of weld pool shape. Lap shear tests revealed that there was a distinctive improvement in joint strength with the Ni plating. Under a 1.4 kW laser power condition, it was noted that the sample with 4 μm Ni plating showed a 49% increase in load and a 100% increase in elongation compared to the sample without plating. Fracture surface observations revealed that Ni addition has changed the crack propagation path resulting in the increased joint strength. Microstructural analysis showed that the Ni is occupied in intermetallic compounds (IMCs) such as Al3Cu2, AlCu, and Al2Cu3 developed at the interface between Cu and Al2Cu which were known as the primary crack propagation phase in Al–Cu laser welded joint. Additionally, increases in their thickness and changes in their shapes to irregular wavy forms were observed, potentially reducing load concentration and increasing joint surface area, facilitating stable joint formation. Density functional theory calculations showed that the IMCs with Ni undergo contraction in the cell volume suggesting solid solution strengthening of IMCs by Ni addition.

Effect of Height and Weight on Heel Fat Pad Movements Between Microchamber and Macrochamber Layers in Loading and Unloading

Background: The purpose of this study was to clarify the differences in the movement of the superficial microchambers and deep macrochambers of the heel fat pad during loading and unloading movements, and to clarify the influence of height and weight on this movement. Methods: The subjects were 21 healthy adults. The right foot was placed on an evaluation instrument stand made of polymethylpentene (PMP) resin plate, and the left foot was placed on a scale stand used to adjust the amount of load. When measuring, the heel fat pad is divided into the superficial microchamber layer and the deep macrochamber layer, and the thickness due to loading from 0% to 100% of the body weight and unloading from 100% to 0% is measured. Measurement was performed every 20% using an ultrasound imaging device. We also examined the rate of change in the thickness of the superficial and deep layers of the heel fat pad when applying 100% load (end load) from 0% load (unload). Results: No changes were observed in the superficial layer of the heel fat pad during unloading, but significant changes were observed in the deeper layers. Additionally, the thickness of the microchamber and macrochamber layers tended to increase under each loading condition as the height and weight increased. On the other hand, the rate of change in the thickness of the macrochamber layer tended to decrease. Conclusion: The microchamber layer and the macrochamber layer of the heel fat pad may have different functions. As height and weight increase, the thickness of the microchamber and macrochamber layers may increase, and the rate of change in the thickness of the macrochamber layer appears to decrease. Although the thickness increases as the load increases, we found that the related elasticity decreases. Level of Evidence: Level Ⅳ, cross-sectional survey study.

Effect of gamma ray irradiation and packaging on the storage quality of kodo millet (Paspalum scrobiculatum L.) flour

Kodo millet is one of the small millet species, grown widely in the tropical/subtropical regions. In order to prevent the problem of post-harvest losses, various preservation techniques have been used such as irradiation and suitable packaging material. In the present study, shelf life of kodo millet flour was investigated using gamma rays at 1.5 kilogray (kGy) (irradiation, IR) and different packaging materials including low-density polyethylene (LDPE), polypropylene (PP), polyethylene terephthalate (PET) and metallized polypropylene (MPP) for a period of three months. Every fortnight the samples from these treatments were drawn for biochemical changes (moisture, peroxide value, alcoholic acidity and FFA), insect infestation and microbial growth. By the end of storage period, significant (P < 0.01) increase of moisture, peroxide value, alcoholic acidity and FFA content was noticed in the control samples followed by non-irradiated PP (10.50 %, 3.8 mEq/Kg and 1.25%) and LDPE (9.48 %, 3.4 mEq and 1.20 %) packed flour as compared to irradiated MPP and PET packed samples. Insect infestation started after 15 days of storage in steel boxes which increased in countless numbers by the end of storage period. Similarly, insect population was noticed after 30 and 60 days in non irradiated and irradiated PP and LDPE covers respectively. While, there was no insect infestation in case of irradiated MPP and PET packed flour. Significant increase of bacterial load was observed in the control followed by non irradiated PP (4.2 cfu/g) and LDPE (3.8 cfu/g) covers. Sensory tests indicated that the irradiation has no adverse effect on the taste, appearance, flavor and overall acceptability (OAA) of the flat bread made from flour samples stored in these packaging materials. Thus, the kodo millet flour stored in MPP and PET pouches with irradiation dose of 1.5 kGy found to be suitable for safe storage up to three months under room temperature.

Thermochemical adsorption heat storage performance of functionalized UiO-66: Molecular simulation method

UiO-66 has broad application prospects in thermochemical adsorption heat storage owing to its great adsorption performance and stability. To further improve its performance, UiO-66 can be functionalized. Nevertheless, the adsorption and diffusion mechanism of UiO-66 and its functionalized structures is still unclear. Therefore, in this paper, it investigated the adsorption and diffusion performance of the UiO-66 series by molecular simulation. The effects of different functional groups were analysed, and the underlying mechanism was revealed. The results showed that adding –OH, –NH2, and –NH3+Cl- groups improved the adsorption capacity of UiO-66 at low pressure by 2.16, 3.22 and 4.25 times respectively, whereas adding –NO2 and −(OMe)2 groups reduced it by 46.05% and 86.84%. The adsorbent-water interaction was the strongest for UiO-66-NH3+Cl-, while UiO-66-(OMe)2 exhibited the weakest interaction. For the UiO-66 series, water molecules were preferentially adsorbed near the zirconium clusters, –OH, –NH2, and –NH3+Cl- groups. Then, they gradually filled around the organic ligands, and a very small amount gathered around the –NO2 and −(OMe)2 groups. Owing to the limitation of the pore volume, the water diffusion coefficient of all the structures initially increased and then decreased with the increase of water loading.

How Does Vertical Wind Shear Influence Updraft Characteristics and Hydrometeor Distributions in Supercell Thunderstorms?

Abstract Vertical wind shear is known to affect supercell thunderstorms by displacing updraft hydrometeor mass downshear, thereby facilitating the storms’ longevity. Shear also impacts the size of supercell updrafts, with stronger shear leading to wider, less dilute, and stronger updrafts with likely greater hydrometeor production. To more clearly define the role of shear across different vertical layers on hydrometeor concentrations and displacements relative to supercell updrafts, a suite of idealized numerical model simulations of supercells was conducted. Shear magnitudes were systematically varied across the 0–1, 1–6, and 6–12 km AGL layers, while the thermodynamic environment was held fixed. Simulations show that as shear magnitude increases, especially from 1 to 6 km, updrafts become wider and less dilute with an increase in hydrometeor loading, along with an increase in the low-level precipitation area/rate and total precipitation accumulation. Even with greater updraft hydrometeor loading amid stronger shear, updrafts are more intense in stronger shear simulations due to larger thermal buoyancy owing to wider, less dilute updraft cores. Furthermore, downshear hydrometeor displacements are larger in environments with stronger 1–6-km shear. In contrast, there is relatively less sensitivity of hydrometeor concentrations and displacements to variations in either 0–1- or 6–12-km shear. Results are consistent across free tropospheric relative humidity sensitivity simulations, which show an increase in updraft size and hydrometeor mass with increasing free tropospheric relative humidity owing to a reduction in entrainment-driven dilution for wider updrafts in moister environments. Significance Statement Rotating thunderstorms, known as supercells, are able to persist for multiple hours. One common explanation is that large changes in wind speed and/or direction with height, or shear, transport rain/hail away from supercell updrafts, supporting their maintenance. The strong shear within supercell environments, however, may also lead to greater rail/hail amounts, thereby leading to weaker storms due to this extra mass of water/ice within updrafts. Furthermore, the impact of shear across different height layers on supercell rain/hail characteristics has not been thoroughly investigated. In this study, computer simulations of supercells were conducted to determine that shear occurring between 1 and 6 km above ground level has a large impact on rain/hail distribution in supercells and that stronger shear in this layer leads to wider/stronger supercells with greater rain/hail accumulations at the surface. Additionally, some of the extra mass of water/ice is transported farther away from updrafts due to the stronger environmental storm-relative winds.

Electroencephalography as a new diagnostic technology for mild psychoneurological disorders

Owing to the increase in the information load in modem society, assessing the clinical characteristics of borderline psychopathological conditions is significantly difficult because we cannot objectively assess them using functional examination methods. To demonstrate the possibility of mathematical analysis of electroencephalography as a new method of clinical electroencephalographic diagnostics for clinically mild conditions, we examined the electroencephalogram indicators of patients who voluntarily and for the first time sought medical help with minimally pronounced clinical manifestations of psychoneurological diseases. The results obtained allowed us to determine that using modern methods of mathematical processing of electroencephalographic signals, we can identify objective differences in the activity indicators of individual cortical structures. The conducted studies allow us to provide practical medicine with a new objective approach to studying human cognitive function.

A data-driven computational optimization framework for designing thin-walled lenticular deployable composite boom with optimal load-bearing and folding capabilities

The thin-walled lenticular deployable composite boom (LDCB) is promising for aerospace engineering applications due to its lightweight and compact nature, but its mechanical behaviors are the main challenges limiting its practical application. Here, the axial compression and folding behaviors of LDCB were numerically simulated and the simulation results were verified according to the experimental data in the literature. Then, a new double chains quantum genetic algorithm (DCQGA)-gaussian process regression (GPR) model and data-driven computational optimization framework were proposed and the new model was trained using a database with 400 simulation results, the superiority of which was demonstrated by prediction accuracy evaluation. Additionally, benchmarking five state-of-the-art algorithms found that the coupling technology of DCQGA-GPR-non-dominated sorting genetic algorithm III (NSGA-III) is an excellent optimization strategy to obtain a well-designed structure of LDCB that maximizes the effectiveness of the material while satisfying the lightweight. The optimized LDCB design exhibits a significant performance improvement, with a 26.3 % reduction in the folding moment, a 34.2 % reduction in the maximum Tsai-Hill failure index, a 43.6 % increase in the critical load, and an 11 % reduction in linear density of mass compared to the initial design.

Viral Load of HBV and HCV Correlation to Torque Teno Virus (TTV) Co-Infection in Iraqi Patients

Abstract Background: While hepatitis viruses A–E are established, emerging evidence points to additional, novel viral hepatitis agents. The torqueteno virus (TTV) has garnered interest due to its prevalence among patients with hepatitis, suggesting potential hepatotropism. Aim: This study was conducted to detect TTV antigens in individuals infected with chronic hepatitis B (HBV) and/or C (HCV) using molecular diagnostics and to explore any associations between TTV presence and demographic characteristics of the cohort. Materials and Methods: The current study was conducted from the period of September 2022 to April 2023, the investigation involved Iraqi patients aged between 32 and 83 years and diagnosed with HBV and HCV in National Iraqi Central Laboratories, Virology Section. We employed real-time PCR to quantify HBV and HCV viral loads and conventional PCR for TTV DNA detection. Results: TTV DNA was detected in 17 of the 60 patients (28.3%) with chronic HBV and HCV infections. Viral load distribution was found to be similar for both HBV and HCV. An age-related increase in viral load was noted, suggesting a trend where older individuals exhibited higher concentrations. However, no significant variation was observed that could link alterations in HBV and HCV viral loads to TTV status directly. Statistical analysis indicated a positive correlation between age and the likelihood of presenting with the virus, aligning with observed trends in other age-associated chronic conditions, such as Type 2 diabetes mellitus and chronic kidney disease. Conclusion: The presence of TTV in patients with enduring HBV or HCV infection could implicate the virus as a contributing factor to hepatitis pathology. Studies such as this are pivotal for elucidating the age-associated risk profiles for various pathologies and shaping corresponding public health policies and preventative approaches.