Increase In Content Research Articles

Effect of Fine Particle Content on Solution Flow and Mass Transfer of Ion-Adsorption-Type Rare Earth Ores

Fine particle content significantly affects the in situ leaching of ion-adsorption-type rare earth ores. This study investigated the effect of fine particle content on solution flow and mass transfer in leaching. The results showed that with the increase in fine particle content, the peak concentration and peak time of rare earth increased. When the fine particle content exceeded 20%, all ion-exchangeable-phase rare earth ions could be replaced with a low dosage of the leaching solution. The leachate flow rate exhibited multi-stage variation, influenced by solution permeation, ion exchange, and fluctuations in accumulated liquid height. A mass transfer analysis showed that a higher fine particle content corresponded to a smaller plate height and a larger plate number of theoretical plates. As fine particle content increased, the final rising height of capillary water decreased, with rising rates varying across different stages for the samples. Moreover, an increase in fine particle content from 5% to 20% resulted in a 94% decrease in the samples’ permeability coefficients. A mechanism analysis showed that when the fine particle content was higher, the fine particles were embedded in the gaps between coarse particles, and the ore particles in the sample were arranged continuously, resulting in a lower permeability coefficient. Then, the leaching solution could penetrate uniformly, which was beneficial for reducing leaching blind spots and improving leaching efficiency. However, excessive fine particle content might have detrimental effects. Based on these results and considering actual mining conditions, the optimal fine particle content for rare earth leaching is 20%.

Effect of Ti and S Content on the Properties and Machinability of Low-Carbon Ferritic–Pearlitic Steel

This research was focused on the effect of Ti and S content on the formation of non-metallic inclusions and their influence on the mechanical properties and machinability of low-carbon ferritic–pearlitic steels. An analysis and classification of the non-metallic inclusions were carried out. The tensile strength and impact toughness were determined from samples taken in the rolling direction. Machinability investigations were carried out on a CNC turning machine and by analyzing the surface roughness. TiO-TiN inclusions are present in steels with an increased Ti content. In these steels, the hardness, tensile strength, and cutting forces increase with a higher proportion of Ti. In the second group of steels with increased contents of S, Al, and Ca, MnS and CaO-Al2O3-MnS non-metallic inclusions are formed. As the S content increases, the tensile strength and cutting forces decrease, while the impact toughness increases. In steels with added Ti, the machining is more difficult, but a finer surface is achieved after turning, while a higher S content results in an increased fraction of softer sulfide inclusions, which reduce the cutting forces but also result in a reduced surface quality.

An experimental and theoretical study on the creep behavior of silt soil in the Yellow River flood area of Zhengzhou City.

We took the silt soil in the Yellow River flood area of Zhengzhou City as the research object and carried out triaxial shear and triaxial creep tests on silt soil with different moisture contents (8%, 10%, 12%, 14%) to analyze the effect of moisture content on silt soil. In addition, the influence of moisture contents on soil creep characteristics and long-term strength was analyzed. Based on the fractional derivative theory, we established a fractional derivative model that can effectively describe the creep characteristics of silt soil in all stages, and used the Levenberg-Marquardt algorithm to inversely identify the relevant parameters of the fractional derivative creep model. The results show that the shear strengths of silt soil samples with moisture contents of 8%, 10%, 12% and 14% are 294kPa, 236kPa, 179kPa and 161kPa, respectively. The shear strength of silt soil decreases with increasing moisture content. When the moisture content increases, the cohesion of the silt soil decreases. Under the same deviatoric stress, the higher the moisture content of the silt soil, the greater the deformation will be. The long-term strength of silt soil decreases exponentially with the increase of moisture content. If the moisture content is 12%, the long-term strength loss rate of silt soil is the smallest, with a value of 32.96%. The calculated values of our creep model based on fractional derivatives have a high goodness of fit with the experimental results. This indicates that our model can better simulate the creep characteristics of silt soil. This study can provide a theoretical basis for engineering construction and geological disaster prevention in silt soil areas in the Yellow River flood area.

Interfacial bond behavior of steel fibers embedded in manufactured sand-based ultra-high performance concrete

The interfacial bond region between matrix and fibers is a non-negligible weak link that can significantly affect the mechanical properties of manufactured sand-based ultra-high-performance concrete (UHPMC). This study investigates the interfacial bond characteristics between steel fiber-UHPMC matrix using single-fiber pullout tests. Four variable parameters were considered: manufactured sand (MS) replacement ratio, stone powder content, fiber embedment length, and steel fiber geometry. Additionally, the microstructure of the steel fiber-UHPMC matrix interface was evaluated using backscattered electron microscopy (BSEM) and scanning electron microscopy (SEM). The results indicate that two typical failure modes including fiber pullout slip failure (in straight and hooked-end fibers) and fiber rupture failure (in corrugated fibers) were observed. The analysis of interfacial evaluation indicators shows that increasing the MS replacement ratio from 25 % to 100 % results in a decreasing trend in peak load, peak tensile stress, and energy consumption. Peak bond strength decreases with increasing embedment length. With the increase in stone powder content, the peak load, peak bond stress, and energy consumption increase initially and then decrease. Additionally, the interfacial failure mechanisms between straight/hooked-end steel fibers and the UHPMC matrix were further elucidated through bond-slip behavior characterization and microstructure analysis. Finally, a design-oriented bond-slip model was developed to predict the interfacial pull-out behavior of steel fiber -UHPMC matrix, showing favorable agreement between predicted and test results. These findings contribute to understanding the interfacial pullout behavior of steel fibers-UHPMC matrix, providing data reference for the performance optimization of UHPMC.

Enhancing Wound Healing and Anti-Inflammatory Effects by Combination of CIGB-258 and Apolipoprotein A-I against Carboxymethyllysine Toxicity in Zebrafish: Insights into Structural Stabilization and Antioxidant Properties

CIGB-258 is known to exert anti-inflammatory activity via structural stabilization of apolipoprotein A-I (apoA-I) and functional enhancement of high-density lipoproteins (HDL) against acute toxicity of carboxymethyllysine (CML). The co-presence of CIGB-258 in reconstituted HDL (rHDL) formed larger rHDL particles and enhanced anti-inflammatory activity in a dose-dependent manner of apoA-I:CIGB-258, 1:0, 1:0.1, 1:0.5, and 1:1 of molar ratio, in the synthesis of the rHDL. However, no study has evaluated the enhancement of HDL functionality by the co-presence of lipid-free apoA-I and CIGB-258. The present study was therefore designed to compare the structural stabilization and functional improvement of HDL in the presence of lipid-free apoA-I and CIGB-258 in molar ratios of 1:0, 1:0.1, 1:0.5, and 1:1 within both HDL2 and HDL3. As the concentration of CIGB-258 increased, it effectively inhibited the cupric-ion-induced oxidation of HDL, thereby safeguarding apoA-I from proteolytic degradation. Additionally, the wound-healing activity of zebrafish was significantly (p < 0.01) enhanced by the co-addition of apoA-I:CIGB-258 (1:1) up to 1.6-fold higher than apoA-I alone (1:0) under the presence of CML. ApoA-I:CIGB-258 (1:1) treatment exhibited the lowest apoptosis and production of reactive oxygen species against CML-induced damage in the wound site. Also, an increase in wounded tissue granulation and epidermis thickness was observed with increasing concentration of CIGB-258 during 48 h post-treatment via the healing process. Intraperitoneal injection of apoA-I:CIGB-258 mixture remarkably ameliorated the acute paralysis and restored zebrafish swimming ability impaired by the acute toxicity of CML. The increase of CIGB-258 content, especially co-injection of apoA-I:CIGB-258 (1:1), leads to a significant 2.3-fold (p < 0.001) and 4.1-fold (p < 0.001) higher zebrafish survivability and recovery of swimming ability, respectively, than those of CML-control. In the apoA-I:CIGB-258 (1:1) group, neutrophil infiltration and interleukin (IL)-6 production was lowest in the hepatic tissue with the least cellular damage and apoptosis. Additionally, the group treated with apoA-I:CIGB-258 (1:1) demonstrated the lowest plasma levels of total cholesterol (TC) and triglycerides (TG), along with minimal damage to the kidney, ovary, and testicular cells. Conclusively, co-treatment of CIGB-258 with apoA-I effectively mitigated acute inflammation in zebrafish, safeguarded vital organs, structurally stabilized apoA-I, and enhanced HDL functionality.

The Eliciting Effect of Aqueous Extracts from Ascophyllum nodosum Algae on the Cultivation of Arugula (Eruca sativa Mill.) Microgreens

This study showed the eliciting effect of aqueous extracts from Ascophyllum nodosum on the development of Eruca sativa microgreens in a quartz-based substrate. There is no information in the literature on the impact of its use on the quality, bioactive compound content, and nutritional value of arugula microgreens. Assays that have been made include the following: total phenolic content (TPC), total flavonoid content (TFV), enzymes such as phenylalanine ammonia (PAL) and polyphenol oxidase (PPO), and enzymes involved in the scavenging of reactive oxygen species such as catalase (CAT) and superoxide dismutase (SOD). The antioxidant activity against DPPH (2,2-diphenyl-1-picrylhydrazyl) was also evaluated. The total phenolic content of arugula microgreens increased significantly after an application of aqueous extracts of A. nodosum to the substrate. The greatest increase in flavonoid content (89%) and antioxidant activity against DPPH (82%) was observed at a concentration of 2.5%. The highest increase in activity of CAT (68.2%), SOD (25%), PAL (13-fold), and PPO (84.2%) was observed with the application of 5% extract. In conclusion, the use of Ascophyllum nodosum algae affects TPC and TFV, antioxidant activity, PAL, PPO, SOD, and CAT in the microgreens studied. By prioritising organic and environmentally friendly extracts, growers can contribute to a more sustainable and healthier food system, especially in the case of the production of Eruca sativa microgreens.

Impact of Package Type on Selected Health Quality Parameters of Organic, Conventional and Wild Raspberries (Rubus idaeus L.) Frozen Stored

Functional foods and the nutritional value of products are now very relevant for consumers. Additionally, interest in biodegradable components made from natural products has recently increased. The aim of this study was to determine the effect of different package types (with addition of films made of biopolymers enriched with natural extracts of ginger, cinnamon, and turmeric) on antioxidative properties of conventional, organic, and wild-grown raspberry fruit during frozen storage for 1-, 4-, 8-, and 12-month periods. The content of total polyphenol and anthocyanins, as well as antioxidant activity, were studied. Additionally, structural (FT-IR and UV-Vis), mechanical (tensile strength and elongation), and surface wetting angle tests of used films were studied. In all crop types, polyphenol content increased at 8 and 12 months of frozen storage in packages with an addition of biopolymer films. There was a statistically significant increase in the amount of total polyphenols in the last month of storage in the package with films with added cinnamon extract. In contrast, packages with ginger-enriched films contributed to an increase in polyphenols only in organically grown and wild raspberry fruit at the 4th, 8th, and 12th month and 8th and 12th month, respectively. The addition of films with turmeric extract increased the polyphenol content in the 8th month of frozen storage of organically grown raspberry fruit and in the 12th month of wild-grown raspberry. During frozen storage of wild raspberry fruit, an increase in anthocyanin content was observed in all cases in the 12th month. This result was almost twice as high as in the control sample. The greatest rise in the content of anthocyanins occurred when packages with films with turmeric extract were applied. Tendencies presented by this paper are not clear-cut in cases of antioxidant activity of analysed raspberries. A common feature was that, in general, after 12 months of storage, raspberries from all crops had higher and statistically significant antioxidant values compared to the first month of storage. Studies on the biocomposite films have shown that the structure of chitosan and alginate polymers was partly decomposed after 12 months, and the natural extracts and raspberry crops used had different effects on the mechanical properties of the biocomposites films. Based on the results of research that has been carried out, it can be concluded that it has not been clearly proven whether the addition of polysaccharide films to packages contributes to the increase in bioactive compounds during frozen storage.

Analysis of the Stability of a High Fill Slope under Different Gradients and Precipitation Conditions

The stability problem of high fill slopes has always been a research hotspot. Its failure mechanism is complex and prominent, featuring strong concealment, a short occurrence time and great harmfulness. In this paper, the stability of a high fill slope under rainfall conditions will be studied by using indoor tests, numerical simulations, etc. The study is based on a high fill slope in Yichang City. The evolution law of high fill slope stability under the maximum rainfall condition is revealed. The results show the following: The influence of moisture content on stress–strain curves is reflected in both the curve’s shape and the peak value of deviatoric stress. Under the constraint of confining pressure, the curve decreases and the peak value of deviatoric stress decreases with the increase of moisture content at the same confining pressure. The safety factor obtained by a rigid body limit equilibrium analysis and numerical calculation indicates that the safety factor for a 30° slope meets the requirements for slope stability evaluation and remains in a fundamentally stable state. An on-site investigation suggests that surface failure and shallow failure may be primary failure modes for this slope; therefore, it is recommended to implement slope protection measures. This study provides valuable references for similar high fill slopes.

Mesoscopic Numerical Simulation of Freeze–Thaw Damage in Hydraulic Concrete

To investigate the impact of freeze–thaw damage on the mechanical properties of concrete, this study utilized Python in combination with ABAQUS 2016 to generate a two-dimensional meso-scale model of concrete. Uniaxial compression tests were conducted on the concrete after freeze–thaw cycles to study the evolution of its mechanical properties. Using “relative compressive strength” as a variable, the relationships between this variable and the parameters of the freeze–thaw damage model were determined, leading to the establishment of the freeze–thaw damage model and the simulation of compressive tests on concrete after freeze–thaw cycles. This study also explored the changes in the mechanical properties of concrete with variations in ITZ parameters and coarse aggregate content. The conclusions drawn are as follows: A comparison with experimental data showed that the model ensures that the relative error of each mechanical property parameter does not exceed 7%, verifying the model’s rationality. Increasing the ratio of ITZ parameters improved the mechanical properties of the ITZ, enhancing the overall mechanical performance, but had almost no effect on the elastic modulus. Compared to ratios of 0.7 and 0.8, concrete with a ratio of 0.9 showed slower rates of decrease in compressive strength and elastic modulus and slower rates of increase in peak compressive strain after freeze–thaw cycles. The increase in coarse aggregate content had a similar effect on the strength and freeze–thaw resistance of concrete as the ratio of ITZ parameters. Concrete with a coarse aggregate content of 60% exhibited slower rates of change in mechanical properties after freeze–thaw cycles.

Pressure tuning of the Se-substituted BiS2-based superconductor LaO0.5F0.5Bi(S1−xSex)2

Abstract We report the effect of hydrostatic pressure on LaO0.5F0.5Bi(S 1 − x Se x )2 with chemical pressure applied to a conducting layer by means of electrical resistivity and ac-magnetic susceptibility measurements up to 2.5 GPa. We confirmed the bulk superconductive nature of the low superconducting (low-SC) and high superconducting (high-SC) phase using ac-magnetic susceptibility under hydrostatic pressure. The T c of the high-SC phase was observed to decrease with an increase in the Se substitution. The critical pressure P c shifted toward the higher P and the P-induced transition broadened with an increase in the Se content. The T c of the low-SC phase can be expressed by assuming an applied hydrostatic pressure of 0.75 GPa as the Se substitution of x = 0.1. The broad P c transition is likely to be ascribed to the inhomogeneity of the Se substitution.

Mechanical properties and damage modeling of hybrid fiber reinforced concrete under freeze-thaw cycles

This study aimed to investigate the mechanical properties of steel-polyacrylonitrile hybrid fiber reinforced concrete and its durability under freeze-thaw damage. Firstly, the mechanical properties of hybrid fiber reinforced concrete were studied by compressive strength and flexural strength tests. Secondly, with the help of rapid freeze-thaw test, the variation rules of mass loss rate and relative dynamic elastic modulus were characterized. Based on the test results and freeze-thaw damage theory, the evolution equation of freeze-thaw damage of hybrid fiber reinforced concrete based on Weibull distribution was established. The results show that the enhancement effect of hybrid fiber on the mechanical strength of concrete is better than that of single mixed fiber, especially in the improvement of flexural strength; Accordingly, compared with the single mixing of steel fibers or single mixing of polyacrylonitrile fibers, hybrid fibers are more effective in improving the durability of concrete against freezing and this improvement effect increases with the increase of steel fiber content; The freeze-thaw damage model of Weibull distribution can better reflect the freeze-thaw damage process of hybrid fiber reinforced concrete .Through the freeze-thaw damage evolution curve, it can be found that after 500 freeze-thaw cycles, the freeze-thaw damage degree of the hybrid fiber reinforced concrete with different steel fiber content has been very close, which means that the influence of steel fiber content on the freeze-resistant performance of hybrid fiber reinforced concrete will be limited. This study provides a theoretical basis and technical basis for the design of concrete structures in alpine regions.

Disruptive effects of sewage intrusion into drinking water: Microbial succession and organic transformation at molecular level

Drinking water distribution systems are increasingly vulnerable to sewage intrusion due to aging water infrastructure and intensifying water stress. While the health risks associated with sewage intrusion have been extensively studied, little is known about the impacts of intruded bacteria and dissolved organic matter (DOM) on microbiology in drinking water. In this dynamic study, we demonstrate that the intrusion of 1 % sewage into tap water resulted in immediate contamination, including an 8-fold increase in biomass (TCC), a 48.9 % increase in bacterial species (ASVs), a 12.5 % increase in organic carbon content (DOC), and a 13.5 % increase in unique DOM molecular formulae. Over time, sewage intrusion altered tap water microbiology by accelerating bacterial growth rates (5-fold faster), selectively promoting ASVs in community succession, and producing 998 more unique DOM formulae. More significantly, statistical analysis revealed that the intrusion of 1 % sewage shifted the driving force of bacterial and DOM composition covariance from a DOM-dependent process in tap water to a bacterial-governed process post-intrusion. Our results clearly demonstrate the disruptive effects of sewage intrusion into tap water, emphasizing the urgent need to consider the long-lasting impacts of sewage intrusion in drinking water distribution systems, in addition to its immediate health risks.

Aromatic Herbs of the Lamiaceae Family as Functional Ingredients in Wheat Tortilla

The rationale for this research is the investigation of the potential health benefits as well as the antibacterial and antifungal properties of selected aromatic plants from the Lamiaceae family, which may lead to the development of improved functional foods. The present study investigated the effects of incorporating dried aromatic plants Thymus vulgaris, Thymus serpyllum, Thymus × citriodorus, Origanum vulgare and Rosmarinus officinalis at a concentration of 1% in refined wheat flour and wholemeal flour on the production of functional tortillas. Sensory analysis was employed to identify the optimal 1% addition, with the objective of achieving a favorable flavor and aroma profile. It was hypothesized that this addition would affect water activity, moisture, texture, color, antioxidant content and phenolic content, thereby enhancing the tortillas as a source of bioactive compounds. The results indicated that the type of flour used had a significant impact on the water activity of the tortillas, with wholemeal flour resulting in higher water activity than refined flour. The water activity ranged between 0.735 and 0.821, while the water content remained relatively stable. The water activity in whole-grain tortillas was significantly higher than that of refined flour tortillas, with a value exceeding 0.8, which makes them susceptible to mold growth and the production of mycotoxins. The sensory evaluations indicated that the enriched refined flour tortillas with common thyme (Thymus vulgaris), lemon thyme (Thymus × citriodorus) and rosemary (Rosmarinus officinalis) were rated highly; a similar result was observed for the whole-grain tortillas enriched with wild thyme (Thymus serpyllum) and lemon thyme. The whole-grain tortillas with rosemary were rated the highest of all the tortillas. The addition of aromatic plants increased the phenolic content and the antioxidant potential, depending on the flour type and the plant used. The addition of wild thyme and rosemary resulted in a significant increase in the phenolic content of wheat tortillas, while all enriched whole-grain tortillas exhibited a higher phenolic content than the control samples. The highest phenolic content in whole-grain tortillas was found in those fortified with rosemary, oregano and wild thyme. The highest antioxidant content was recorded in tortillas prepared with rosemary, irrespective of whether the flour used was refined or wholemeal. Fourteen phenolic compounds were tentatively identified in aromatic plants tested. The main phenolic compounds in Origanum vulgare were flavonoids. Rosmarinic acid was the dominant phenolic compound in rosemary and all thyme species, reaching the highest level in rosemary. Such high levels of rosmarinic acid may be responsible for the high antioxidant and total phenolic contents observed in rosemary extracts and also in tortillas when this plant is included in the recipe. The results of this study indicate that selected aromatic plants, particularly rosemary, have the potential to be utilized as functional ingredients in bakery products. By incorporating dried aromatic plants from the Lamiaceae family into wheat flour tortillas, food manufacturers can create products that not only taste better but also provide added health benefits. The use of selected herbs can improve the nutritional profile of tortillas by increasing antioxidant properties and, due to the properties of herbs, extend the shelf life of the product.

Performance optimization design of high ductility concrete rapid repair material incorporating coal gangue aggregate

In order to solve the problem of efficient and effective repair after brittle cracking of concrete on road and bridge deck pavements, and to consider the resource utilization of coal gangue solid waste, the river sand was replaced by coal gangue and a high ductile concrete rapid repair material (HDCRRM) was prepared through performance optimization design. First, the fluidity and compressive strength of materials mixed with different amounts of sulfoaluminate cement (SAC), fly ash, lithium carbonate, calcium hydroxide, calcium formate, sand-binder ratio, water-binder ratio and polycarboxylate superplasticizer were studied, so as to determine the preferred benchmark mix proportion. Then, the replacement rate of coal gangue was optimized to develop HDCRRM. Test results show that the reduction of SAC cement and the increase of fly ash content can weaken the compressive strength of material. The rational design content of lithium carbonate, calcium hydroxide, calcium formate, sand-binder ratio, water-binder ratio and polycarboxylate superplasticizer all can improve the fluidity and compressive strength of the materials within a certain range. When the replacement rate of coal gangue aggregate increases, the tensile elastic modulus and ultimate tensile strength of HDCRRM material decrease, while the ultimate tensile strain increases. When the replacement rate of coal gangue aggregate is 100 %, the compressive strength of HDCRRM is 40.5 MPa, the ultimate tensile strain is 2.83 %, and the average crack width is 50.27μm. The early compressive strength of HDCRRM is mainly provided by a large amount of ettringite and C-S-H gel.

Effects of ultrasonic treatment on the structure and functional characteristics of myofibrillar proteins from black soldier fly

In the process of utilizing black soldier fly larvae (BSFL) lipids to develop biodiesel, many by-products will be produced, especially the underutilized protein components. These proteins can be recycled through appropriate treatment and technology, such as the preparation of feed, biofertilizers or other kinds of bio-products, so as to achieve the efficient use of resources and reduce the generation of waste. Myofibrillar protein (MP), as the most important component of protein, is highly susceptible to environmental influences, leading to oxidation and deterioration, which ultimately affects the overall performance of the protein and product quality. For it to be high-quality and fully exploited, in this study, black soldier fly myofibrillar protein (BMP) was extracted and primarily subjected to ultrasonic treatment to investigate the impact of varying ultrasonic powers (300, 500, 700, 900 W) on the structure and functional properties of BMP. The results indicated that as ultrasonic power increased, the sulfhydryl content and turbidity of BMP decreased, leading to a notable improvement in the stability of the protein emulsion system. SEM images corroborated the changes in the microstructure of BMP. Moreover, the enhancement of ultrasound power induced modifications in the intrinsic fluorescence spectra and FTIR spectra of BMP. Additionally, ultrasonic treatment resulted in an increase in carbonyl content and emulsifying activity of BMP, with both peaking at 500 W. It was noteworthy that BMP treated with ultrasound exhibited stronger digestibility compared to the untreated. In summary, 500 W was determined as the optimal ultrasound parameter for this study. Overall, ultrasound modification of insect MPs emerges as a dependable technique capable of altering the structure and functionality of BMP.

Oryza glumaepatula and calcium oxide nanoparticles enhanced Cr stress tolerance by maintaining antioxidant defense, chlorophyll and gene expression levels in rice

Chromium (Cr), a potent heavy metal, threatens rice cultivation due to its escalating presence in soil from human activities. Wild rice contains useful genes for phytoremediation; however, it is difficult to use directly for metal mitigation. Here, a single segment substitution line (SSSL), SG001, was developed by crossing O. glumaepatula and Huajingxian74 (HJX) to evaluate the survival ability of plants against Cr. Further, we explored the potential effect of calcium oxide nanoparticles (CaO-NPs) (50 μM) to minimize the toxic effect of Cr (100 μM) in rice cultivars, SG001 and HJX. The findings of this study indicated that Cr toxicity led to increased oxidative stress. This was shown by higher levels of hydrogen peroxide (H2O2), which was increased by 104% in SG001 and 177% in HJX, and malondialdehyde (MDA) increased by 79% in SG001 and 135% in HJX. Furthermore, it also depicted that Cr toxicity considerably declined shoot and root length, shoot and root fresh weight by 30%, 27%, 25%, and 20% in SG001 and 44%, 51%, 42%, and 45% in HJX, respectively. This mitigation was evidenced by decreased Cr contents, increased calcium (Ca) levels in SG001, and the maintenance of chlorophyll, antioxidant defense, and gene expression levels. Moreover, there was a notable reduction in MDA and H2O2, while the defense mechanisms of key antioxidants, including ascorbate peroxidase, superoxide dismutase, glutathione, catalase, and peroxidase were upregulated, along with an increase in soluble protein contents in both rice cultivars after applying CaO-NPs. CaO-NPs effectively restored cellular and subcellular structural integrity and growth in both lines, which had been seriously disrupted by Cr toxicity. Overall, our findings suggest that SG001, in combination with CaO-NPs, could serve as an effective strategy to mitigate Cr toxicity in plants.

Discussion on the applicability and mechanism of phosphate-based geopolymers used for cadmium and cadmium-lead heavy metals solidification/stabilization

Lead (Pb2+) and cadmium (Cd2+) are common heavy metal pollution, which is harmful to humans and animals. However, the diffusion rate of heavy metal ions moves faster in acidic environment, there are a large number of acidic heavy metal polluted soil in China, but the conventional binders are not effective to deal with them. Phosphate-based geopolymers (PGEOs) are acidic materials, and have excellence mechanical properties in acidic environment and solidification/stabilization (S/S) effect on Pb2+, but the applicability of PGEOs to Cd, Pb and Cd composite pollution is not clear. Therefore, this study discusses the applicability of PGEOs fabricated from fly ash (FA) and aluminum dihydrogen phosphate (ADP) as activator for S/S treatment of Cd, Pb-Cd composite pollution. Results show that the influence of Cd2+ and Pb2+ on the compressive strength of PGEOs was inconsistent, as the Cd2+ content raised, the compressive strength reduced slightly at 7 and 14 days, but it did not change basically at 28 days. However, the compressive strength rose firstly and then declined with an increase in Pb-Cd content when partial Pb2+ was used to replace Cd2+. The compressive strength of PGEOs with a Pb-Cd content of 0.6 % reached maximum (11.45 MPa), exceeding the compressive strength of PGEOs containing Cd2+. Moreover, the PGEOs presents an excellent stabilization effect on Pb2+, but poor effect on Cd2+. The Pb2+ leaching concentration meet the hazardous solid waste identification criteria (<5 mg/L), but the Cd2+ leaching is high and is more than 1 mg/L. Furthermore, the compressive strength of PGEOs had a good correlation with pH and EC. The S/S mechanism of PGEOs for Pb2+, Cd2+ includes physical adsorption, encapsulation, and chemical precipitation. However, Pb2+ involved in the geopolymerization process, while Cd2+ can not participate in the structure formation, so the PGEOs have a poor S/S effect. Therefore, it needs to be further improved when using PGEOs to stabilize acidic Cd2+ contaminated soil.

Effect of Fe2O3 addition on synthesis of diamond single crystal under high-pressure and high-temperature conditions

The influence of Fe2O3 addition on the growth characteristics of synthetic diamonds under high-temperature and high-pressure conditions was systematically investigated in this work. Utilizing Fe2O3 as an oxygen source within the Fe-Ni-C-O system, oxygen-containing diamond single crystals were synthesized. The role of the oxygen atoms during the growth of large-sized diamonds with the {111} face as the growth surface was also analyzed. In addition, the morphology, growth rate, internal nitrogen content, and crystal quality of the crystals were examined. From our analysis, it was demonstrated that an increase in Fe2O3 addition leads to a reduction in the size of the synthetic crystals and a gradual decrease in the growth rate. The diamonds with complete crystal forms exhibited no significant change in color, and all appeared yellow. When the addition exceeded a threshold, cracks appeared around the seed crystal at about 0.3 mm, resulting in a cracked crystal phenomenon. A further increase in the Fe2O3 addition resulted in the skeleton crystal, and the crystal color turned black. Fourier Transform Infrared Spectroscopy (FTIR) measurements were also conducted, indicating that the introduction of oxygen atoms increases the nitrogen content in the crystals, which in turn aggregates in the form of C-centered nitrogen. The Raman spectroscopy results showed that as Fe2O3 addition in the crystals increases, more impurities are introduced, leading to an increase in the diamond stress and a shift in the diamond Raman peak, along with an increase in the full width at half maximum. The photoluminescence (PL) characterization results indicated that with the increase of the Fe2O3 addition, the intensity of the photoluminescence peaks of NV− centers and W8 centers was enhanced, which is related to the increase in the internal C-centered nitrogen content of the crystals. From the acquired results, it was proven that Fe2O3 addition has a significant impact on the synthesis of diamond single crystals. Our work provides valuable pieces of experimental evidence for exploring the formation mechanism of natural diamonds.

Mechanistic study of carbon dioxide sequestration technology using molecular simulations to assess the adsorption of methane and carbon dioxide by different functional groups

To investigate the characteristics of CO2 and CH4 adsorption across various functional groups and to clarify their thermodynamic attributes, slit models of functional groups with different pore sizes and moisture contents were constructed using the Materials Studio software program. The analysis focused on the characteristics of CO2 and CH4 adsorption in six distinct models comprising different functional groups. The results showed that the adsorption activities of the six functional groups followed the order –CHO>–COOH>–OH>-O-CH3 > –CH3 > –CH2CH3. The average adsorption heat of the oxygen-containing functional groups exceeded that of the aliphatic groups for both the single- or two-component injections of CO2. As the moisture content increases, the maximum adsorption capacity of CH4 in the slit models with –CH2CH3, −O-CH3, –COOH, and –OH functional groups show a significant decreasing trend when injecting CH4 with two components. The absolute value of the adsorption energy of CO2 and CH4 decreases with increasing pore size. In the slit models with –CHO and –COOH functional groups, multiple peaks appear in the adsorption energy of CO2, indicating a greater number of adsorption sites. For the two-component injection of CO2 and CH4, the entropy of CO2 in each functional group was minimized at a pore size of 1 nm.

L-type Ca2+ channel activation of STIM1–Orai1 signaling remodels the dendritic spine ER to maintain long-term structural plasticity

Learning and memory require coordinated structural and functional plasticity at neuronal glutamatergic synapses located on dendritic spines. Here, we investigated how the endoplasmic reticulum (ER) controls postsynaptic Ca2+ signaling and long-term potentiation of dendritic spine size, i.e., sLTP that accompanies functional strengthening of glutamatergic synaptic transmission. In most ER-containing (ER+) spines, high-frequency optical glutamate uncaging (HFGU) induced long-lasting sLTP that was accompanied by a persistent increase in spine ER content downstream of a signaling cascade engaged by N-methyl-D-aspartate receptors (NMDARs), L-type Ca2+ channels (LTCCs), and Orai1 channels, the latter being activated by stromal interaction molecule 1 (STIM1) in response to ER Ca2+ release. In contrast, HFGU stimulation of ER-lacking (ER-) spines expressed only transient sLTP and exhibited weaker Ca2+ signals noticeably lacking Orai1 and ER contributions. Consistent with spine ER regulating structural metaplasticity, delivery of a second stimulus to ER- spines induced ER recruitment along with persistent sLTP, whereas ER+ spines showed no additional increases in size or ER content in response to sequential stimulation. Surprisingly, the physical interaction between STIM1 and Orai1 induced by ER Ca2+ release, but not the resulting Ca2+ entry through Orai1 channels, proved necessary for the persistent increases in both spine size and ER content required for expression of long-lasting late sLTP.