Implants Of Different Diameters Research Articles

A retrospective study of dynamic navigation system-assisted implant placement

BackgroundTo evaluate the accuracy of implant placement assisted by a dynamic navigation system, as well as its influencing factors and learning curve.MethodsAt Macao We Care Dental Center, 55 cases of implant placement using dynamic navigation were retrospectively evaluated. To evaluate their accuracy, the apex, tip, and angle deviations of preoperatively planned and postoperatively placed implants were measured. The effects of the upper and lower jaws, different sites or lateral locations of dental implants, and the length and diameter of the implants on accuracy were analyzed, as well as the variation in accuracy with the increase in the number of surgical procedures performed by dentists.ResultsThe implant had an apex deviation of 1.60 ± 0.94 mm, a tip deviation of 1.83 ± 1.03 mm, and an angle deviation of 3.80 ± 2.09 mm. Statistical differences were observed in the tip deviation of implants at different positions based on three factors: jaw position, lateral location, and tooth position (P < 0.05). The tip deviation of the anterior teeth area was significantly greater than those of the premolar and molar areas. There were no statistically significant differences in apex deviation, tip deviation, or angle deviation between the implants of different diameters and lengths (P > 0.05). There were significant differences in the angle deviation between the final 27 implants and the first 28 implants. Learning curve analysis revealed that angle deviation was negatively correlated with the number of surgical procedures, whereas the regression of apex deviation and tip deviation did not differ statistically.ConclusionsThe accuracy of dynamic navigation-assisted dental implants meets the clinical needs and is higher than that of traditional implants. Different jaw positions, lateral locations, and implant diameters and lengths had no effect on the accuracy of the dental implants guided by the dynamic navigation system. The anterior teeth area had a larger tip deviation than the posterior teeth area did. As the number of dynamic implantation procedures performed by the same implant doctor increased, the angle deviation gradually decreased.

НАПРЯЖЕННО-ДЕФОРМИРОВАННОЕ СОСТОЯНИЕ В КОСТИ И ИНТЕРФЕЙСЕ «ИМПЛАНТАТ — КОСТЬ»

Introduction. This article presents the results of mathematical modeling of the stress-strain state in the bone tissue surrounding the implant and the implant-bone connection depending on the diameter and length of the implant in the case of different directions of force application and the implant-bone implant installation angle.&#x0D; Target. To study the effect of the diameter, length of the implant and the load angle on the stress fields in a three-dimensional implant-bone system with finite elements and determine the effect of the load angle on the stress fields with a change in diameter and length.&#x0D; Materials and methods. To study the distribution and analysis of the stress-strain state in the bone tissue around implants of different diameters and lengths during dental implantation, a three-dimensional finite element model of the lower jaw was created. Three models were developed using computed tomography and the Universal Surgical Integration System software.&#x0D; Results. In all cases studied, the maximum stresses were achieved in the cortical bone due to its greater rigidity. However, since cortical and cancellous bone have different strength characteristics, it was necessary to consider the stress in these areas separately.&#x0D; In the cortical bone, the maximum stresses were always reached near the edge of the hole and the contact with the implant, respectively. In cancellous bone, in many cases, the maximum stresses were noted in the region of the implant apex. At the same time, when the implant is placed at an angle or in the buccolingual direction of load application, the stresses are redistributed in favor of the cancellous bone.&#x0D; Findings. Thus, in general, it can be concluded that an increase in the length and diameter of the implant leads to a noticeable decrease in stresses in the bone tissue surrounding the implant and in the implant-bone junction. The obtained results demonstrated that implants of small diameter and length, installed in the jawbone at an oblique loading angle, are the least favorable option for stress distribution at the implant-bone interface.

Comparison of marginal bone loss in implant supported over dentures in early loading

Aim: The purpose of the present research was to evaluate the marginal bone loss in implant supported over-dentures in case of early loading on denture. Methodology: 36 edentulous participants (mean age 68 years, SD 9.2) were randomly assigned into three treatment groups (n¼12). A single implant was placed in the mandibular midline of participants to support an overdenture using a 6-week loading protocol. The control group received Southern regular implants and standard ball attachments. One group received Southern 8-mm-wide implants and large ball attachments. Another group received Neoss regular implants and Locator attachments. SPSS was used to determine between groups differences in marginal bone loss, implant stability, implant, and prosthodontic success (P&lt;0.05). Results: Implant success after 1 year was 75% for Southern regular implant (control) group; and 100% for the Southern wide and Neoss regular implant groups (P¼0.038). Prosthodontic success was comparable between the groups but the maintenance (41 events overall, mean 1.2) was greater for the Locator and the standard ball attachments. Conclusion: Mandibular single-implant overdentures are a successful treatment option for older edentulous adults with early loading protocol using implants of different diameters and with different attachment systems.

Effect of Implant Diameter and Bruxism on Biomechanical Performance in Maxillary All-on-4 Treatment: A 3D Finite Element Analysis.

To examine the stress distribution in the maxillary All-on-4 treatment concept supported by implants of different diameters under two different loading forces using finite element analysis. Two distinct All-on-4 designs were prepared in a fully edentulous maxilla, supported by 3.3- and 4.1-mm-diameter implants. Posterior implants were tilted distally, approximately 30 degrees to the occlusal plane, and anterior implants were placed axially. Bone, implant, and prosthetic components were modeled separately and were tightly connected to each other. Under two distinct loading conditions representing the occlusal forces of healthy and bruxist individuals, the stresses on peri-implant bone, implant, and prosthetic components were evaluated using finite element analysis. There were higher stresses on cortical bone than on trabecular bone. The stresses on bone and implant components were concentrated around the posterior implants, whereas stresses on the prosthesis were concentrated anteriorly. With increasing implant diameter, the stresses on trabecular bone, abutments, and crowns increased, whereas the stresses on cortical bone, implants, and frameworks decreased. Compressive stresses in the cortical bone and von Mises stresses in the frameworks exceeded the overload limit in both models under bruxist loading. The stresses on the cortical bone, implants, and frameworks were slightly higher in the model with 3.3-mm-diameter implants, whereas the stresses on the trabecular bone, abutments, and crowns were slightly higher in the model with 4.1-mm-diameter implants.

Rotational Load Fatigue Performance of Titanium vs Titanium-Zirconium Implant-Abutment Connections.

Titanium-zirconium (Ti-Zr) alloy has been developed to strengthen the implant body, but clinically relevant information is still limited. The aim of this in vitro study was to compare the rotational load fatigue performance of implant-abutment connections in narrow-diameter (3.3-mm) and regular-diameter (4.1-mm) implants made with commercially pure grade 4 titanium alloy (CPTi-G4) and Ti-Zr. Narrow-diameter (N) and regular-diameter (R) implants with CPTi-G4 (Ti) or Ti-Zr (Tz) materials were tested. This resulted in four test groups: NTi, NTz, RTi and RTz. Five specimens were made for each group (n = 5). Abutments used were milled from titanium-aluminum-niobium alloy abutment blanks. A rotational load fatigue machine applied a sinusoidally varying load at an angle of 45 degrees to produce an effective bending moment of 35 Ncm at a frequency of 14 Hz in air at 20°C. The number of cycles to failure was recorded. The upper limit was set as 5 million cycles. Results were evaluated using analysis of variance (ANOVA) and Tukey post hoc tests. Failure locations and patterns were evaluated with scanning electron microscope (SEM). All regular-diameter test groups reached the upper limit of 5 million cycles without failure. All narrow-diameter test groups failed within the range of 402,530 cycles to 3,374,353 cycles. It could be observed that NTz showed a higher mean cycle count as compared to NTi. NTi test group recorded two implants damaged, one implant fracture, five abutment fractures, and four screw fractures. NTz test group showed only abutment fractures at the level of implant platform, with no damage to the implant bodies. Significant difference was found between implants of different diameters. There was no significant difference between implants of different materials. Regular-diameter implants performed significantly better than narrow-diameter implants, regardless of material, while no significant difference in cyclic load to failure was found between groups of different alloys. All NTz failures were at the abutment only, without damage to the implant. This failure pattern can potentially be clinically advantageous in terms of retrieval and subsequent replacement of a failed prosthesis.

Different implant diameters and their effect on stress distribution pattern in 2-implant mandibular overdentures: A 3D finite element analysis study

Statement of problemThe edentulous mandible is commonly treated with a 2-implant overdenture. A change in diameter of the implants may affect the biomechanical behavior of the overdenture, but information on these effects is lacking. PurposeThe purpose of this 3D finite element analysis study was to evaluate the biomechanical behavior of 2-implant mandibular overdentures (2IMO) and their individual components by using implants of different diameters. Material and methodsA 3D mandibular model was obtained from the cone beam computed tomography (CBCT) images of a 59-year-old edentulous man, and a 3D denture model was developed from intraoral scanning files in the Mimics software program. A 3D model of different diameters of implants (2.5 mm, 3.0 mm, 3.5 mm, and 4.0 mm) with a LOCATOR attachment was developed in the Solidworks software program. Two same-sized implants were inserted in the mandibular model at 10 mm from the midline in the 3Matics software program. A vertical load of 100 N was applied on the first molar region on the right side or both sides in the ANSYS software program. The maximum von Mises stresses and strains were recorded and analyzed. ResultsStresses within the implants decreased with an increase in diameter (from 2.5 mm to 3 mm, 3.5 mm, and 4.0 mm) of the implants. The highest stresses were observed with 2.5-mm-diameter implants (0.949 MPa under unilateral and 0.915 MPa under bilateral loading) and the lowest with Ø4-mm implants (0.710 MPa under unilateral and 0.703 MPa under bilateral loading). The strains on the implants ranged between 0.0000056 and 0.0000097, and those on the mandible ranged between 0.0000513 and 0.0000566 across all diameters of the implants without following a specific trend. ConclusionsIn 2IMO, the stresses in the implants and mandible decreased with an increase in the diameter of the implants. The implants of lesser diameter (2.5 mm) exhibited the highest stresses and strains, and the implants of the largest diameter (4 mm) exhibited the lowest stresses and strains under unilateral and bilateral loading conditions.

Biomechanical Stress Analysis of Platform Switch Implants of Varying Diameters on Different Densities of Bone.

Purpose The purpose of this study was to evaluate and compare the strain developed in D2 and D3 types of bones on vertical loading by platform switch implants of different diameters. Materials and Methods Implants of diameters 3.25 mm, 4.2 mm, and 5.0 mm and of length 11.5 mm were taken and placed each on D2 and D3 bone models. Strain gauges were attached on the buccal and the lingual sides on each of these samples, and a vertical load of 190N was placed on the samples. The strain was recorded using a data logger. The data obtained was analysed using one-way ANOVA and post hoc Tukey test. Results In D2 and D3 bone models, 3.25 mm significantly showed greater bone strain values. The buccal side strain was higher irrespective of the implant diameter and density of bone. Conclusion Within the limitations of the study, it may be concluded that the narrow diameter implant produces greater strain than 4.2 and 5.0 mm diameter implants, respectively. The buccal side consistently produced higher bone strain values.

Effect of implantoplasty on the elastic limit of dental implants of different diameters

BackgroundImplantoplasty reduces both implant diameter and the thickness of its walls, subsequently reducing the ability of the implant to resist fracture in response to functional load. In combination with an increase in the crown-implant ratio due to bone loss, this could increase the lever effect, which in presence of high masticatory forces or parafunctional habits, could lead to complications such as fracture of the implant or loosening of the prosthetic screw.ObjectivesTo determine the elastic limits of internal connection, dental implants of different designs and diameters after an implantoplasty.Materials and methodsThis in vitro study included 315 tapered internal connection titanium dental implants, the threads of which were removed with an industrial milling machine—for standardized implantoplasty (IMP1; n = 105)—or with the conventional approach—manually, using high-speed burs (IMP2; n = 105). The remaining 105 implants were used as controls. The final implant diameters were recorded. The quality of the newly polished surfaces was assessed by scanning electron microscopy. All implants were subjected to a mechanical pressure resistance test. A Tukey’s test for multiple comparisons was used to detect differences in the elastic limit and final implant diameters between the implant groups.ResultsThere were statistically significant differences in the elastic limit between the IMP1, IMP2, and control groups (p < 0.05). Furthermore, the implant diameter was significantly smaller in the IMP1 and IMP2 groups (p < 0.05). Scanning electron microscopy revealed smooth implant surfaces in the IMP1 and IMP2 groups, with some titanium particles visible in the IMP1 group.ConclusionsImplantoplasty significantly decreased the elastic limit of internal connection titanium dental implants, especially in those with a smaller diameter (3-3.5 mm).

Influence of Inter-Radicular Septal Bone Quantity in Primary Stability of Immediate Molar Implants with Different Length and Diameter Placed in Mandibular Region. A Cone-Beam Computed Tomography-Based Simulated Implant Study.

Aim:The purpose of this in vitro study was to investigate the influence of length and width of implant on primary stability in immediate implants in mandibular first molar.Materials and Methods:The study was carried out on 40 cone-beam computed tomography scans selected with defined inclusion and exclusion criteria. According to the diameter and length of implants, they were divided into nine groups (G1 to G9). The virtual implants of different diameters and length were placed in mandibular first molar and measurements were done for peri-implant horizontal and vertical gap defect, peri-implant interradicular bone support and apical bone support for all the groups.Results:The study groups Diameter, (D-7 mm) showed least horizontal gap defect (Buccal-1.30 ± 0.56 mm, lingual-1.30 ± 0.56 mm, mesial-1.20 ± 0.51 mm, and distal-1.05 ± 0.59 mm) as compared to regular implant diameter (D-4.7) groups (Buccal-2.35 ± 0.483 mm, lingual-2.10 mm ± 0.44 mm, mesial-2.30 ± 0.64 mm, and distal-2.25 ± 0.43 mm). The unsupported Vertical implant gap defect at the coronal part of the socket was 2.80 mm ± 0.83 mm for all groups in both horizontal and vertical direction. The vertical peri-implant interradicular bone support showed increased bone support with increase in implant length (L). The buccal and lingual inter-radicular bone-support was least for Length (L-8.5 mm), moderate for L-11.5 mm, and highest for L-13.5 mm groups, respectively. The mesial inter-radicular bone support was least for G4G7, moderate for G1G2G5G8, and maximum for G3G6G9 groups. Similarly, the distal inter-radicular bone support was least for G4G7, moderate for G1G5G8, and maximum for G2G3G6G9 groups, respectively. There was no apical bone support in L-8.5 mm group as the tip of implant was 3.5–4 mm within the socket tip. Whereas, L-11.5 mm had decent (0.9–1 mm) and L-13.5 mm had Good (1.35–1.95 mm) apical bone support as the implant tip was beyond the socket tip.Conclusion:All the groups showed good interradicular bone support on buccal and lingual surfaces. Regular width implants with longer length showed satisfactory interradicular bone support on mesial and distal surfaces. Longer implants showed good apical bone support in all the four surfaces and hence good apical primary stability expected.

Effects of insertion torque on the structure of dental implants with different connections: Experimental pilot study in vitro.

ObjectiveDuring the insertion of dental implants in the bone tissue, different torque values can be applied. However, the high applied torque can cause damage to the implant connection. Our study sought to evaluate, by measuring the angle of rotation of the insertion drive and, later microscopic observation, possible changes in the structure of implants of different diameters with 3 different types of connections after the application of 4 different torque intensities.Materials and methodsThree hundred tapered dental implants and three hundred insertion drivers were used in the present study. Implants of 3.5 and 4 mm in diameter with 3 connection models were tested: external hexagon (EH), internal hexagon (IH) and Morse taper (MT). Then, sis groups were performed: EH3 group, EH4 group, IH3 group, IH4 group, MT3 group and MT4 group. The samples were submitted to the torque/torsion force at 4 intensities (n = 10 samples per group and intensity): 60, 80, 100 and 120 Ncm. The turning angle of the insertion driver was measured in each test. In addition, in 10 samples from each group, the maximum torque value supported by each implant model was measured. After the tests, all samples were inspected microscopically to describe the observed changes.ResultsThe maximum torque supported by the different implant models showed statistically significant difference (p < 0.0001). The values of the measured angles showed statistically significant differences between the torque values applied within each group (p < 0.001) and between groups with the same torque value (p < 0.001).ConclusionsWithin the limitations of the present study in vitro, the results showed that high torque values cause mechanical damage to the implants.

Comparative Evaluation of Primary Stability between Different Diameters Multi-Scale Roughness Dental Implant by Solid Rigid Polyurethane Simulation

Background: Implant primary stability is determined by screw characteristics and surgical procedure. The aim of the present study was to evaluate, on a polyurethane model, the insertion torque (IT), removal torque (RT), and resonance frequency analysis (RFA) of multi-scale roughness dental implants of different diameters. Methods: Two implant sizes were tested on two polyurethane blocks (20 pounds per cubic foot (PCF) and 30 PCF): 3.0 diameter and 13 mm length and 5.0 diameter and 13 mm length. The IT, RT, and RFA were assessed. Results: A significant difference of IT and RT was present in favor of wider implants at both polyurethane densities. No statistical difference was present between the 5.0 diameter and 3.0 diameter implants at both polyurethane densities. A statistically increased RFA was reported for 5.0 implant 30 PCF polyurethane blocks. Conclusions: Multi-scale roughness dental implants of both diameters showed high insertion torque and primary stability on polyurethane blocks, which is valuable for implant loading protocols.

Effects of implant diameter, implant-abutment connection type, and bone density on the biomechanical stability of implant components and bone: A finite element analysis study

Statement of problemVarious kinds of implants of different diameters and connection types are used for patients with a range of bone densities and tooth sizes. However, comprehensive studies simultaneously analyzing the biomechanical effects of different diameters, connection types, and bone densities are scarce. PurposeThe purpose of this 3-dimensional finite element analysis study was to evaluate the stress and strain distribution on implants, abutments, and surrounding bones depending on different diameters, connection types, and bone densities. Material and methodsTwelve 3-dimensional models of the implant, restoration, and surrounding bone were simulated in the mandibular first molar region, including 2 bone densities (low, high), 2 implant-abutment connection types (internal tissue level, internal bone level), and 3 implant diameters (3.5 mm, 4.0 mm, and 4.5 mm). The occlusal force was 200 N axially and 100 N obliquely. Statistical analysis was performed using the general linear model univariate procedure with partial eta squared (ηp2) (α=.05). ResultsFor bone tissue, low-density bone induced a larger maximum and minimum principal strain (in magnitude) than high-density bone (P<.001). As the implant diameter increased, the volume of the cancellous bone in low-density bone at the atrophy region (strain<200 με) increased (P<.001). For implant and abutment, the internal bone-level connection type was associated with increased peak stress as compared with the tissue-level connection type (P<.001). For all models, the stress distribution on the implant complex was influenced by implant diameter (P<.001): a decrease in implant diameter increased the stress concentration. ConclusionsThe implant connection type had a greater impact on the stress of the implant and abutment than the diameter. A tissue-level connection was more advantageous than a bone-level connection in terms of stress distribution of the implant and abutment. Bone density was the most influential factor on bone strain. The selection of dental implants should be made considering these factors and other important factors including tooth size.

Effect of vertical bone loss on stress distribution at the bone-implant interface around implants of varying diameters–an in silico 3D finite element analysis

Peri-implantitis results in loss of supporting bone around an implant. An implant thus compromised, must distribute and dissipate the stresses hence generated, in an attempt to survive. A three- dimensional Finite Element Analysis helps the clinician simulate such critical clinical situations in an attempt to predict the best way ahead. The aim of this study was to determine the distribution of stresses around an implant once Peri-implantitis associated vertical bone loss enters the picture. An attempt was also made to analyse the effect of varying the implant diameter on stresses generated. A 3-D Finite Element Analysis was carried out for implants replacing lost mandibular first molars. Threaded implants of different diameters (3.75 mm, 4.3 mm, 5.0 mm) with varying levels of Peri-implantitis induced vertical bone loss were modelled and load of 118.2 N applied to the occlusal surface at an angle of 75°. Vertical stress maps presented as a ring like configuration around the implant with highest values being recorded mesially and distally. Stresses in the cortical bone were found to decrease as more bone was lost and vice versa for trabecular bone. With the bone being lost circumferentially, models beyond 10% angular bone resorption had no cortical bone in vicinity, and hence the loads were borne primarily by the cancellous bone. Cancellous bone was able to distribute stresses over a much wider area than cortical bone. Implant diameter profoundly affected the stresses generated in cortical bone, with 4.3 mm diameter being the most optimum biomechanically in majority of the bone loss situations.

STRAIN GAUGE ANALYSIS OF AXIAL AND OFF AXIAL LOADING ON IMPLANTS FOR REPLACING FIRST MANDIBULAR MOLAR (INVITRO STUDY)

INTRODUCTION: Mechanical overload is thought to be one of the major causes of implant complications. It may induce loosening and fracture of the superstructure and/or implant components. Bone loss may also occur at the implant-bone interface. Increasing the diameter and length of the implant decreased the stress and strain on the alveolar crest, but diameter had a more significant effect than length to relieve the crestal stress and strain concentration. When the mesiodistal dimension is greater than 14 mm, using at least two implants to restore the region should be considered. When two implants replace the molar region, the mesiodistal offset loads to the prosthesis can be eliminated. OBJECTIVES: Evaluation of the axial and off axial loading on implants of different diameters for replacing first mandibular molar. MATERIALS AND METHODS: Fifteen epoxy resin blocks in which implants of different diameters were fixed. Specimens were divided into 3 parallel groups, 5 specimens each according to the implant diameter. Evaluation of the strain distribution around the implants under vertical axial and off axial loading using the strain gauge was done. RESULTS: The total microstrain mean value of the double implants was significantly less than the 6mm wide implant and the 4.7mm diameter implant. CONCLUSIONS: On using dental implants for replacing mandibular first molar, double (3.75-3.75) mm diameter implants revealed reducing microstrains than 6-mm-diameter implant and 4.7 diameter implant and give wider support to the crown restoration leading to elimination of the mesiodistal cantilever.

How do differences of dental implants' internal connection systems affect stress distribution?: A 3-dimensional finite element analysis

Background/Aim: A factor affecting the success rate of dental implants, which has been used successfully for many years, is the implant-abutment connection system. The purpose of this study was to evaluate the stress distribution of different implant-abutment connection systems under different forces. Material and Methods: This in vitro study included a finite element analysis. In the study, the cylindrical and screwed dental implants available in 3 different diameters from 4 different companies were categorized into 12 different models. Two different scenarios of force application were conducted on each model in this study. In the first scenario, 100 N force and 100 N moment were applied in a vertical direction onto a point considered as the center of each tooth. In the second scenario, a 100 N force and moment were applied at a 45˚ angle in an oblique direction. Results: As a result of the forces applied to dental implants of different diameters from different companies, octagon implant-abutment connection systems had less stress accumulation than hexagon implant-abutment connection systems. In addition, when stress accumulation ratios were evaluated according to the diameter of the implants used, it was observed that 3 mm diameter implants accumulated more stress in bone than 4 mm diameter implants; there was no significant difference between 4 mm diameter implants and 5 mm diameter implants. Conclusions: Implant-abutment connection system is important for the longevity of implants under the forces. Therefore, this factor should be considered during implant selection.

Analysis of the distribution of stress and deformation in single implant-supported prosthetic units in implants of different diameters

Abstract Introduction When stress and strain levels in the bone-implant system exceed It's capacity, a mechanical fatigue occurs, resulting in collapse and loss of osseointegration. Objective Analyze biomechanical behavior in single implant-supported prosthesis with implants of different diameters in the posterior mandible. Material and method Three different finite element models of Cone-Morse implants with the same height were created, varying the diameter (3.3 mm, 4.1 mm and 4.8 mm). The mandibular first molar area was the location of the implant, with It´s component and overlying prosthetic crown. The jawbone was composed of cortical and cancellous bone. Refined mesh of 0.5 mm was created in the critical interfaces to be analyzed. The loading of the models was performed at the point of occlusal contact with an occlusal load of 400 N. Result Maximum stress and strain occurred in the cervical regions of the implants in all groups, either in the implants or in components as well as in the analysis of cortical bone. The greater the diameter, the lower the stress and strain found in the implant. The 3.3 mm group had the highest strain in peri-implant cortical bone, and the 4.1 mm group had the smallest deformation, significantly lower than in the 4.8 mm group. Conclusion Although the biggest implant diameter (4.8 mm) appears to have lower values of stress and strain, the group of intermediate implant diameter (4.1 mm) showed less deformation rate in the cortical peri-implant bone. Therefore it is concluded that the 4.1 mm implant platform presented a more biomechanically effective peri-implant bone maintenance.

Measurement of strain distribution in cortical bone around miniscrew implants used for orthodontic anchorage using digital speckle pattern interferometry

An application of digital speckle pattern interferometry (DSPI) for the measurement of deformations and strain-field distributions developed in cortical bone around orthodontic miniscrew implants inserted into the human maxilla is presented. The purpose of this study is to measure and compare the strain distribution in cortical bone/miniscrew interface of human maxilla around miniscrew implants of different diameters, different implant lengths, and implants of different commercially available companies. The technique is also used to measure tilt/rotation of canine caused due to the application of retraction springs. The proposed technique has high sensitivity and enables the observation of deformation/strain distribution. In DSPI, two specklegrams are recorded corresponding to pre- and postloading of the retraction spring. The DSPI fringe pattern is observed by subtracting these two specklegrams. Optical phase was extracted using Riesz transform and the monogenic signal from a single DSPI fringe pattern. The obtained phase is used to calculate the parameters of interest such as displacement/deformation and strain/stress. The experiment was conducted on a dry human skull fulfilling the criteria of intact dental arches and all teeth present. Eight different miniscrew implants were loaded with an insertion angulation of 45 deg in the inter-radicular region of the maxillary second premolar and molar region. The loading of miniscrew implants was done with force level (150 gf) by nickel–titanium closed-coil springs (9 mm). The obtained results from DSPI reveal that implant diameter and implant length affect the displacement and strain distribution in cortical bone layer surrounding the miniscrew implant.

Measurements of Implant Stability Following Sinus Lift: A Pilot Clinical Study.

The aim of this study was to evaluate the implant stability of Bredent Sky Blue implants of different diameters following one stage sinus lift procedure. This study included 9 male patients with an existing indication for unilateral or bilateral sinus lift procedure. As grafting materials, combination of allograft material MinerOss® cortical & cancellous and Ossceram nano were used. All implants were considered successful and ISQ levels were measured by Osstell ISQ device. The ISQ values were from 68 to 84. The mean values of stability of Bredent Sky Blue implants of different diameters following one stage sinus lift procedure were 77.73 ± 2.93 (MD) and 77.98 ± 2.72 (VO).

Maxillary Crestal Bone Loss around Bredent Sky Blue Implants: One Year Study

Objective: To analyze the amount of crestal bone loss of the mandible around implants of different diameters one year after implantation. Material and Methods: The study included a total of 42 male and female patients. A total of 73 implants were evaluated (12 implants of diameter 3.5 x 10 mm and 61 implants of diameter 4.0 x 8 mm). Dental panoramic radiographs were made before surgery, immediately after surgery and one year later. The measurements were performed using Kodak dental software 6.11.7.0 after implantation and one year later. The data were analyzed using the IBM SPSS v.17 software package (descriptive statistics, paired samples t-test). Results: Among male patients, 43.5% were smokers, while among females, 57.9% were nonsmokers. Crestal bone resorption was greater mesially than distally, although differences were not statistically significant (p<0.05). Conclusion: All implants showed successful tissue integration. Crestal bone resorption was greater mesially than distally, although differences were not statistically significant.

Mandibular single-implant overdentures: preliminary results of a randomised-control trial on early loading with different implant diameters and attachment systems

To determine surgical and prosthodontic outcomes of mandibular single-implant overdentures, opposing complete maxillary dentures, using a wide diameter implant and large ball attachment system compared with different regular diameter implants with standard attachment systems. Thirty-six edentulous participants (mean age 68 years, SD 9.2) were randomly assigned into three treatment groups (n=12). A single implant was placed in the mandibular midline of participants to support an overdenture using a 6-week loading protocol. The control group received Southern regular implants and standard ball attachments. One group received Southern 8-mm-wide implants and large ball attachments. Another group received Neoss regular implants and Locator attachments. Parametric and non-parametric tests of a statistical software package (SPSS) were used to determine between groups differences in marginal bone loss, implant stability, implant, and prosthodontic success (P<0.05). Implant success after 1 year was 75% for Southern regular implant (control) group; and 100% for the Southern wide and Neoss regular implant groups (P=0.038). Mean marginal bone loss at 1 year was 0.19 mm (SD 0.39) without significant differences observed. Implant stability quotient (ISQ) at baseline was significantly lower for the Southern regular (control) group than the other two groups (P=0.001; P=0.009). At 1 year, no significant difference in implant stability was observed (mean ISQ 74.6, SD 6.1). The change in implant stability from baseline to 1 year was significant for the control group (P=0.025). Prosthodontic success was comparable between the groups but the maintenance (41 events overall, mean 1.2) was greater for the Locator and the standard ball attachments. Mandibular single-implant overdentures are a successful treatment option for older edentulous adults with early loading protocol using implants of different diameters and with different attachment systems.